Samsung CS25M6HN8X/BWT, CS29M6HT8X/BWT Service Manual

COLOR TELEVISION RECEIVER

Chassis : KS3A(P)_100Hz(Rev. 5) Model : CS25M6HN8X/BWT

CS29M6HT8X/BWT

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Troubleshooting

Exploded Views and Parts List

Electrical Parts List

Block Diagrams

Wiring Diagram

Schematic Diagrams

10.

ELECTRONICS

Printed in Korea

AA82-00063A

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGE CURRENT

TESTER

DEVICE UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified

limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground

system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to

have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

Precautions

Samsung Electronics 1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Reference Information

Samsung Electronics 2-1

2. Reference Information

2-1 Tables of Abbreviations and Acronyms

A Ah Å dB dBm

°C °F °K F G GHz g H Hz h ips kWh kg kHz kΩ km km/h kV kVA kW I MHz

Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz

MV MW MΩ m µA µF µH µm µs µW mA mg mH mI mm ms mV nF

Ω

pF Ib rpm rps s V VA W Wh

Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour

Table 2-1 Abbreviations

Reference Information

2-2 Samsung Electronics

Table 2-2 Table of Acronyms

ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF

Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency

I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR

Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor

Reference Information

Samsung Electronics 2-3

Table 2 - 3 IC Line - Up

DESCRIPTION

Video Processor

Sipadoss-Module, Video Processor

Multistandard Sound Processor MICOM, TTX(MTP)

EEPROM Audio AMP

RGB Drive AMP Hybrid IC

100Hz Horizontal Pulse AMP Vertical IC

Horizontal Drive IC

E/W Drive IC

SPS Controllor

Bridge Diode Photo Coupler

5V Controlled Regulator

Rectifier Diode

3.3V Regulator 6V Regulator

8V Controlled Regulator

3.3V Regulator MICOM Reset IC

2-2 IC Line Up

LOC. NO

IC201S

IC601 IC901 IC902

IC602

HIC201 HIC202 HIC203

HIC204 HIC401

IC301

Q402 Q401

D414

IC401

Q404

IC801S

D801S

PC801S

IC802

D805 D806

D807

D802 IC201 IC804

IC803 IC903

IC904

BOARD

MAIN

SPEC

VDP3140 DDP3310 VPC3230

OKI/SDA9401

MSP3411G

SDA555X

KS24L161

TDA7297

DRGB001

DDRI001

LA7845

BUZ73A

2SC5446 FMP-3FU

KA393 IRF620

3S1265RB

3S1265RD

RBV606

PC123Y

KA78R05

FML-G12S

FMG-G2CS KA78RM33

KA7806

KA78R08

KA78RM33 KIA7025AP

REMARK

Refer to Table 2-3-1

Refer to Table 2-3-2

Refer to Table 2-3-3

VM Option

Option

HC401

HC801

2-4 Samsung Electronics

SPEC

VDP3140D

DDP3310 VPC3230

OKi

SDA9401

FUNCTION

100Hz Video Processor

Sipadoss Module AA98-00133A(with OKi) AA98-00134B(with SDA9401)

REMARK

Table 2-3-1 VIDEO IC (IC201S)

Table 2 - 3 IC Line - Up

DESCRIPTION

IIC Level Shifter

Video Output AMP R.G.B Drive

Push-Pull (VM)

TR-Power (TILT)

OP-AMP (TILT) OP-AMP

TR-Power Video Switching IC with Adder Output

High-end Picture-In Picture IC 1-TUNER PIP

3.3V Regulator

LOC. NO

Q909

Q910 IC501 IC502 IC503

QF04

QF05 QG02 QG03 ICG01 ICH01 QH01 ICS01

ICP01

ICP0

SPEC

2N7000

TDA5109

TDA6111Q

2SC2344 2SA1011

KSA940

KSD2073-H2

KA4558 KA4558

2SC4636RB

TEA6425

SDA9489X

SDA9488

EZ1086CM

REMARK

FLAT FLAT FLAT

Option

Option Option Option Option

BOARD

MAIN

CRT

DOUBLE

FOCUS

V-S/W

PIP

Reference Information

Samsung Electronics 2-5

SPEC

MSP3400D MSP3410D MSP3411G

FUNCTION

Multistandard, A2 Stereo Multistandard, A2 Stereo, Nicam Multistandard, A2 Stereo, Nicam, Vitual Dolby

REMARK

SPEC

TDA7297

FUNCTION

15W x 2CH, 10W x 2CH

REMARK

Table 2-3-2 SOUND IC (IC601)

Table 2-3-3 SOUND AMP (IC602)

SPEC

TCLS3101PD09A(S) TCPS3000P TCPS3001PD09E(S) TCPW3001PD09A(S)

TCLS3101PD16A

FUNCTION

CS with LNA Function CS CS CZ, CW

REMARK

Main(Old)

India

Main(New)

SPEC

TCPS3000PC09B(S)

TCPS3000PC16B

FUNCTION

CS CS

REMARK

Sub(Old() Sub(New)

TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.

Table 2-3-4 1’st TUNER (TU01S)

Table 2-3-5 2’nd TUNER (TU02S)

Note

Reference Information

2-6 Samsung Electronics

MEMO

Specifications

Samsung Electronics 3-1

3. Specifications

Specifications are subject to change.

Television

System

Antena Input

Power

Consumption

Requirements

Frequency

Sound

Output

Effect

Jacks

Front (AV2)

Back

PAL/SECAM-B/G,D/K,L,I, NTSC-M

130W (Applied When 29” Flat)

220V Only

Free Voltage

50/60Hz

15W x 2CH

10W x 2CH

5W x 2CH

Virtual Dolby

Turbo Sound

Pseudo Stereo

RCA Input

S-VHS

Head-Phone

2Scart Input/Output

DVD Input(YPbPr)

AV2 Monitor Audio Output

S-VHS

75ohms, Coaxial Cable

Not Present R815

Option

AV1 : Scart I/O, RGB Input,

RF Out

AV2 : Scart I/O, Monitor Out

Option

Function

2 TUNER PIP, TTX, A2 STEREO + NICAM

TTX, A2 STEREO + NICAM

Non PIP, Non TTX, A2 STEREO + NICAM

NOTE

29 Inch

21 Inch

Specifications for Model Name (Ex. CS29A6??8X/HAC)

3-2 Samsung Electronics

MEMO

Alignment and Adjustments

Samsung Electronics 4-1

4. Alignment and Adjustments

4-1 General Alignment Instructions

1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus.

2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below.

3. Use the specified test equipment or its equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results.

6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

8. To protect against shock hazard, use an isolation transformer.

4-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.

The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes.

If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF.

If color shading persists, perform the following Color purity and Convergence adjustments.

4-3 High voltage Check

CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).

1. Connect a digital voltmeter to the second anode of the picture tube.

2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current).

3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.

Alignment and Adjustments

4-2 Samsung Electronics

4-5 SCREEN Adjustment

1. Input Toshiba Pattern

2. Enter “Service Mode”.(Refer to “Service Mode”)

3. Select “G2-Adjust”.

4. Set the values as example(Refer to page4-17).

4-4 Dynamic Focus Adjustment

1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT.

2. Input a crosshatch pattern.

3. Enter “ STANDARD “ in video mode.

4. Turn the Dynamic focus VR fully clockwise (maximum).( )

5. Turn the Static focus VR fully counterclockwise (maximum).( )

6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( )

7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.( )

8. Repeat 4-7, if necessary.

❷

❶

❷

❶

❷

❶

❷

❶

ex) IBRM = 220

WDRV = 35 CDL = 220 COLR G B = 150 150 150

STATIC FOCUS VR

DYNAMIC FOCUS VR

SCREEN

Alignment and Adjustments

Samsung Electronics 4-3

5. Turn the SCREEN VR until “MRCR G B” and “MRWDG” are green and those value are about 100. (The incorrect SCREEN Voltage may result that “MRCR G B” and “MRWDG” should be red)

When you do not have Toshiba Pattern, follow this method.

1. Set the TV on the condition that AV mode no signal(black)

2. Enter the “Menu” and set the mode to blue screen off.

3. Enter the “Service Mode”.

4. Select “ G2-Adjust”.

5. Set the values as example(Refer to page4-17).

ex) IBRM = 220

WDRV = 35 CDL = 220 COLR G B = 150 150 150

6. Turn the SCREEN VR until the value of “ MRCR G B” is about 120. Do not mind that

the “OSD” Color is red.

■ After completing G2-Adjust, follow this procedure.

① Enter the “Video Adjust 1”. ➁ Choose any item in menu. (ex. Select “Red Cutoff”) ➂ Change the value of item you select, and recover the value.

For example, when the value of “Red Cutoff” is 127, change the value to 128 and restore the value to 127.

If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.

Note 1.

Alignment and Adjustments

4-4 Samsung Electronics

4-6 E2PROM (IC902) Replacement

1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted.

2. After IC902 is replaced, connect the AC power supply cord.

3. Turn the power switch ON.

4. In stand-by, warm up the TV for at least 10 seconds.

5. Power on the TV.

4-7 White Balance Adjustment

■ Equipment : Color-Analyzer (CA-100)

■ Input Signal : Pattern signal (Toshiba pattern)

1. Select STANDARD from the menu.

2. Input an 100% White pattern.

3. Enter the “Service Mode”. (Refer to “4-8 Service Mode”)

4. Warm up the TV set at least for 30 minutes.

5. Input a Toshiba pattern signal.

6. Enter the “Video Adjust1”.

- Adjust “Sub Contrast” so that Y (luminance) becomes 40 ft ± 3.

- Use “Red Drive” and “ Blue Drive” to adjust High-Light (x : 290, y : 300)

- Adjust “Sub Bright” so that Y (luminance) becomes 1.3ft ± 0.3.

- Use “Red Cutoff” and “Blue Cutoff” to adjust Low-Light (x : 290, y : 300).

7. Adjust CA-100 so that the final adjustment value can be fixed.

8. Use the Channel Up/Down (▲/▼) buttons to move the cursor on the adjustment modes.

9. Use the Volume +/- buttons to change the adjustment value.

Alignment and Adjustments

Samsung Electronics 4-5

4-8 Factory Adjustment

1. To enter the “Service Mode”, Press the remote-control keys in this sequence :

- If you do not have Factory remote-control

- If you have Factory remote-control

2. After the Service Mode is entered, the initial screen is as shown in the figure below.

3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters.

- When CRT, CRT PCB, FBT, E

PROM (sometimes MICOM) is replaced, the adjustment values

should be controlled.

- After the Service adjustment is completed, Do not select “Reset” in the service mode menu.

(After above procedure is done, power is on initially and the “Plug and Play” will be operated.)

4-8-1 Service Mode

These hexa digits are check sum value which depends on the MICOM. If check sum value is changed, the value of

PROM Data newly initialed.

Note 2.

PICTURE OFF PICTURE ON

PICTURE ON

Service

Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option(81h 0Ch) Reset G2-Adjust Others

DISPLAY

()

FACTORY

MUTE

Alignment and Adjustments

4-6 Samsung Electronics

4-8-2 Memory Data

4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)

No.

OSD

V Amp

V Shift

V Slope

V SC

H EW

H Trapizium

H Parabola

H Corner U

H Corner L

H Shift

BOW

Amgle

H Corner U6

H Corner L6

V Max

Zoom1 Amp

Zoom2 Amp

Zoom Trap

H-QEW

Zoom 4:3 Para

4:3~16:9 Para

Range

0 ~255

Function

Adjusts Vertical picture size. Adjusts 4:4 upper and lower picture size in a lion head pattern at factory.

Adjusts Vertical picture position

Adjust Vertical Slope Correction

Adjusts Vertical s-correction

Horizontal east west width. Adjusts 5:5 left and right picture size in a lion head pattern at factory.

Adjusts horizontal Trapezium.

Adjusts Horizontal Parabola.

Adjusts the top horizontal corner of picture. Adjusts so that the top of H corner can be linear.

Adjusts the bottom horizontal corner of picture. Adjusts so that the bottom of H corner can be linear.

Adjusts Horizontal Position

Adjusts Horizontal BOW

Adjusts Horizontal Angle

Adjusts so that the top horizontal corner of picture can be linear

Adjusts so that the bottom horizontal corner of picture can be linear

Adjusts Max value of vertical amplitude

Adjusts vertical amplitude in zoom1

SIM-806HEW only.

Adjusts horizontal Trapezium in Zoom

Short for Q-CRT HORIZNOTAL EAST WEST,data used for only Q-CRT MODEL. In NORMAL mode,horizontal picture size is within 5 ~ 5.5.In Q mode, horizontal picture size is within 6.5 ~ 7. This H QEW function sets the gap between horizontal picture size in NORMAL mode and horizontal picture size in Q mode.

Corrects the vertical linearity in Zoom mode of P-SIZE. The data depends on CRT (see data above).

Corrects the vertical linearity in 16:9 mode of P-SIZE.. The data depends on CRT (see data above).

Remark

Adjust

Fix

Adjust

Fix

Adjust

Fix

Alignment and Adjustments

Samsung Electronics 4-7

V Amp V Shift V Slope V SC H EW H Trapizium H Parabola H Corner L H Corner L H Shift BOW Amgle H Corner U6 H Corner L6 V Max Zoom1 Amp Zoom2 Amp Zoom Trap H-QEW Zoom 4:3 Para 4:3~16:9 Para

RANGEOSD

0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255

RANGEOSD

0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255

INITIAL DATA

SIM-806HEW

32W8VH

Philips

Invar Flat

80 104 125 117 125

88 185 132 129 176 176 128 150 202 128

32W8VH Thomson Invar Flat

92 111 130 225 215 113

96 121 122 170 130 140

78 128 143 173 128 128

28C7VH

Thomson

Invar 2.0R

85 108 130 200 205

65 118 136 174 123 129 140 136 213 180 202 128

28C7H

Thomson

AK 2.0R

129 110 130 200 187 114

91 118 136 180 123 129 133 129 213 180 202 128 128

28C7H Philips

Invar 2.0R

129 110 130 200 187 114

91 118 136 180 123 129 133 129 213 180 202 128

INITIAL DATA

SIM-806HEW SIM-806HMA/806HEA/806HC

29A8VH

SED

Invar Flat

128 153 133 210 109 108 112 125 118 183 123 129 126 136 200 195 202 128 128

28W8VH

SED

Invar Flat

104 109 107 175 161 124 110 108 111 188 127 127 138 140 127 148 178 128 128

29A7HP

SED

V-Before

148 149 134 206 183 110

94 130 133 195 127 128 131 130 200 187

128 128

29A7HP

SED

V-After

106 141 134 206 195 105

79 130 143 195 127 128 131 130 200 179

128 128

28W6

Thomson

AK 2.0R

84 117 130 200 172 108

82 118 136 177 121 132 135 126 128 146 171 128 128

34A7HP Toshiba

V-Before

133 151 134 189 179

81 145 150 186 127 128 127 134 200 198

131 128

32W6V

Remarks

Thomson

Invar 2.0R

80 116 115 150 232 107

92 185 123 129 159 158 128 150 190 128

34A7HP

GEOM GEOM

FIX

FIX GEOM GEOM GEOM

FIX

FIX GEOM GEOM GEOM GEOM GEOM

FIX

Remarks

Toshiba

V-After

124 125 125 210 215

71 134 159 189 127 128 133 126 200 189

131 128

GEOM GEOM

FIX

FIX GEOM GEOM GEOM

FIX

FIX GEOM GEOM GEOM GEOM GEOM

FIX

Alignment and Adjustments

4-8 Samsung Electronics

4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)

1 V Amp

V Slope

5 H EW

7 H Parabola

9 H Corner L

2 V Shift

V SC

H Trapizium

H Corner U

H Shift

11 BOW

13 H Corner U6

15 V Max 16 Zoom Trap

17 Zoom 4:3 Para

Angle

14 H Corner L6

18 4:3~10:9 Para

+ 49 hidden pages

Samsung CS25M6HN8X/BWT, CS29M6HT8X/BWT Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual