The performance of the remote control may be affected by bright light.
➢
8
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the television
◆ Find that the remote control is no longer operating
correctly
1Remove the cover on the rear of the remote control by pressing
the symbol
2Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆-on the battery against -on the remote control
◆+on the battery against +on the remote control
3Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
()
downwards and then pulling firmly to remove it.
ENG
9
ENG
Connecting to an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the TV
P 4
or
Cable Television
Network
Mono
1In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the television.
2If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to:
◆“Storing Channels Automatically” on page 15.
◆“Storing Channels Manually” on page 16.
Signal Strength( ) display (Option)
➢
The “ ”(Signal Strength) symbol is displayed by
pressing the “INFO ()” button. This symbol displays
signal strength for your watching TV channel. The more
signal bar is the better TV gets sensitivity on current
channel.
10
Switching Your Television On and Off
The mains lead is attached to the rear of your television.
1Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the television
➢
and the frequency is 50 or 60Hz.
2Press the “ ” button (On/Off) on the front of the television.
Result
:The Standby indicator on the front of the television
lights up.
3Press the POWER () button on the remote control to switch the
television on.
Result
:The programme that you were watching last is re-
selected automatically.
If you have not yet stored any channels, No clear picture
➢
appears. Refer to “Storing Channels Automatically” on page
15 or “Storing Channels Manually” on page 16.
4To switch your television off, press the “ ” button (On/Off) again.
ENG
Placing Your Television in Standby Mode
Your television can be placed in Standby mode, in order to reduce:
◆ Power consumption
◆ Wear of the cathode ray tube
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1Press the POWER () button on the remote control.
Result
:The screen is turned off and the Standby indicator on
the front of the television lights up in red.
2To switch the television back on, simply press the POWER ()
button again.
You can also switch on by pressing the Por button.
➢
Do not leave your television in Standby mode for long
☛
periods of time (when you are away on holiday, for
example). Turn your television off by pressing the “”
button (On/Off) on the front of the television. It is best to
unplug the set from the mains and aerial.
11
ENG
Becoming Familiar with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up the television using the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
ButtonViewing FunctionMenu Function
Used to display the next
stored channel.
Used to display the previous
stored channel.
to Used to display the corresponding channels.
-/--
PRE-CHPress the PRE-CH button. The TV will switch to the last
MUTEUsed to switch the sound off temporarily.
MENUUsed to display theUsed to return to the previous
Used to select a channel numbered ten or over.
Press this button, and the “
Enter the two-digit channel number.
channel viewed.
To quickly switch between two channels that are far apart,
tune to one channel, then use the number button to select
second channel. Then, use the PRE-CH button to quickly
alternate between them.
Used to increase the volume.
Used to decrease the volume.
To turn the sound back on, press this button again, or
➢
press theorbutton.
on-screen menu system.menu or normal viewing.
--
” symbol is displayed.
-
-
-
-
12
-
-
EXIT
TV◆ Used to return the TV
mode when it is in external
input mode.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
Used to confirm your choice.
Used to exit from the menu
system and return to normal
viewing directly.
-
Plug & Play Feature (depending on the model)
When the television is initially powered on, three basic customer
settings proceed automatically and subsequently: setting the
language, channel and clock.
ENG
Plug & Play
1If the television is in Standby mode, press the POWER () button
on the remote control.
Result
:The message Plug & Play is displayed. It flickers for
a little while and then
Language menu is automatically
displayed.
2Select the appropriate language by pressing the ▼ or ▲ button.
Press the
Result
➢
ENTER () button to enter the language.
:The message Check antenna input. is displayed.
If any language is not selected on the Language menu, the
Language menu will disappear about 30 seconds later.
3Make sure that the antenna is connected to the TV.
Press the
Result
ENTER () button.
:The Auto Store menu is displayed with Area is
selected.
4Press the ENTER () button again. Select your area by pressing
the
▼ or ▲ button, and then Press the ENTER () button.
To search the channels, select
Search by pressing the ▼ or ▲
button, and then press the ENTER () button.
Press the
Press the
Result
➢
ENTER () button again to start search the channels.
MENU () button to stop the search.
:The Time menu is displayed with Clock is selected.
Refer to “Storing Channels Automatically” on page 15.
5Press the œ or √ button to move to the hour or minute. Set the
hour or minute by pressing the
Refer to “Setting and Displaying the Current Time” on page
➢
30.
▼ or ▲ button.
6When you have finished, press the MENU () button.
Result
:The message Enjoy your watching is displayed,
and then the channel which has been stored will be
activated.
7If you want to reset this feature...
Language
English
Melayu
Indonesia
MoveEnter
Check antenna input.
Enter Exit
TV
Area: ASIA W/EUROPE
Search
MoveEnterReturn
TV
Clock-- : -- am
Sleep Timer: Off
On Timer-- : -- am Off
Off Timer-- : -- am Off
On Timer Volume: 10
MoveEnterReturn
Auto Store
Search
Start
Enter Return
Time
√√
√√
1 Press the MENU () button.
2 Press the ▼ or ▲ button to select Setup, and then press the
ENTER () button.
Result
:The Plug & Play is selected.
3 Press the ENTER () button again.
Result
:This feature starts with the message
Plug & Play
is displayed.
Enjoy your watching
TV
Plug & Play
Language: English
Time
Child Lock
Blue Screen: Off
Melody: On
Demonstration
MoveEnterReturn
13
Setup
√√
√√
√√
√√
√√
√√
ENG
Viewing the Demonstration
TV
Plug & Play
Language: English
Time
Child Lock
Blue screen: Off
Melody: On
Demonstration
MoveEnterReturn
Setup
To become familiar with the various menus provided by your
television, you can view the in built demonstration.
√√
√√
√√
√√
√√
√√
1Press the MENU () button.
Result
:The main menu is displayed.
2Press the ▼ or ▲ button to select Setup.
Result
:The options available in the Setup group are
displayed.
3Press the ENTER () button.
4Press the ▼ or ▲ button to select Demonstration.
5Press the ENTER () button.
Result
:Each of the menu options is displayed in turn.
When you wish to exit from the demonstration, press the
➢
EXIT () button on the remote control.
Choosing Your Language
TV
Plug & Play
Language: English
Time
Child Lock
Blue screen: Off
Melody: On
Demonstration
MoveEnterReturn
Setup
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
√√
√√
√√
√√
√√
√√
1Press the MENU () button.
Result
:The main menu is displayed.
2Press the ▼ or ▲ button to select Setup.
Result
:The options available in the
Setup group are
displayed.
3Press the ENTER () button.
4Press the ▼ or ▲ button to select Language.
5Select the appropriate language by pressing the ENTER ()
button repeatedly.
14
Storing Channels Automatically
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers manually and
clear any channels you do not wish to watch.
TV
Auto Store
Manual Store
Add/Delete
Sort
LNA: Off
ENG
Channel
√√
√√
√√
√√
√√
1Press the MENU () button.
Result
:The main menu is displayed.
2Press the ▼ or ▲ button to select Channel.
Result
:The options available in the Channel group are
displayed.
3Press the ENTER () button.
Result
:The Auto Store is selected.
4Press the ENTER () button again.
Result
:The options available in the Auto Store group are
displayed with
Area is selected.
5Press the ENTER () button again.
6Select your area by pressing the ▼ or ▲ button, then press the
ENTER () button.
The areas are displayed in the following order:
ASIA W/EUROPE-CIS E/EUROPE-CHINA-HONGKONG U/K
-
AUSTRALIA-NZ/INDONESIA-SOUTH AFRICA-AMERICA
7Press the ▼ or ▲ button to select Search, then press the ENTER
() button.
8Press the ENTER () button to start the search.
Result
:The horizontal bar is displayed, and then channels are
stored in an order which reflects their positions in the
frequency range. Finally, the search will end
automatically.
To stop the search before it has finished, press the MENU
➢
() button.
9When searching and storing are complete, the Sort menu is
displayed.
◆
To sort the stored channels into the desired numerical order,
go to Step
on page 19.
◆
To exit from the channel store function without sorting the
channels, press the
menus disappear.
6 of the “Sorting the Stored Channels” procedure
MENU () button repeatedly until the
MoveEnterReturn
TV
Area: ASIA W/EUROPE
Search
MoveEnterReturn
TV
Area: ASIA W/EUROPE
Search
MoveEnterReturn
P1 102 MHZ
TV
From: P 1
To: P--
Store: ?
Auto Store
ASIA W/EUROPE
CIS E/EUROPE
CHINA
HONGKONG U/K
AUSTRALIA
NZ/INDONESIA
SOUTH AFRICA
AMERICA
Auto Store
Search
Start
Enter Return
Search
Stop
Enter Return
Sort
√√
√√
√√
√√
7%
10When the channels have been stored, you can:
◆
Sort them in the order required (refer to page 19)
◆
Clear a channel (refer to page 18)
◆
Activate the Digital Noise Reduction feature (refer to page 23)
MoveAdjustReturn
15
ENG
Storing Channels Manually
TV
Auto Store
Manual Store
Add/Delete
Sort
LNA: Off
MoveEnterReturn
Channel
You can store the channels, including those received via cable
√√
√√
√√
√√
√√
networks.
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
TV
Programme: P 3
Color System: AUTO
Sound System: BG
Search: 46MHz
Channel: C 1
Store: ?
MoveAdjustReturn
TV
Programme: P 3
Color System: AUTO
Sound System: BG
Search: 46MHz
Channel: C 1
Store: ?
MoveEnterReturn
TV
Programme: P 3
Color System: Auto
Sound System: BG
Search: 46MHz
Channel: P 1
Store: ?
MoveEnterReturn
TV
Programme: P 3
Color System: AUTO
Sound System: BG
Search: 46MHz
Channel: C 1
Store: ?
MoveEnterReturn
TV
Programme: P 3
Color System: AUTO
Sound System: BG
Search: 46MHz
Channel: C 1
Store: ?
MoveEnterReturn
Manual Store
Manual Store
Manual Store
AUTO
PAL
SECAM
NT4.43
NT3.58
Manual Store
Manual Store
BG
DK
I
M
1Press the MENU () button.
Result
√√
√√
2Press the ▼ or ▲ button to select Channel.
:The main menu is displayed.
3Press the ENTER () button.
Result
:The options available in the Channel group are
displayed.
4Press the ▼ or ▲ button to select Manual Store.
√√
√√
5Press the ENTER () button.
6To assign a programme number to a channel, press the œ or √
button.
7Press the ▼ or ▲ button to select Color system.
8Press the ENTER () button.
9Press the ▼ or ▲ button to select the broadcasting standards.
√√
√√
Result
:The color standards are displayed in the following
order:
AUTO-PAL-SECAM-NT4.43-NT3.58.
10Press the ENTER () button.
11Press the ▼ or ▲ button to select Sound System .
12Press the ENTER () button.
√√
√√
13Press the ▼ or ▲ button to select the sound standards.
Result
:The sound standards are displayed in the following
order:
BG-DK-I-M.
14Press the ENTER () button.
√√
√√
16
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.