Samsung CS-21M6N User Manual
COLOUR
TELEVISION
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ENG
REMOTE CONTROL
ON-SCREEN MENUS
TELETEXT FUNCTION
(depending on the model)
2
ENG
Safety Instructions
The following illustrations represent the precautions to be taken when using and moving your television.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS
Caution
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO
NOT REMOVE REAR COVER, NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION
Do NOT expose the television to
extreme temperature conditions
(below 5°C and above 35°C) or to
extreme humidity conditions (less
than 10% and more than 75%).
Do NOT expose the television to
direct sunlight.
Do NOT expose the television to
any liquids.
If the television is broken, do not
try to repair it yourself. Contact
qualified service personnel.
During a storm conditions
(especially when there is lightning)
unplug the television from the
mains socket and aerial.
If the remote control is not used for
a long period of time, remove the
batteries and store it in a cool, dry
place.
Mode System
CZ PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43MHz
CW PAL-B/G, D/K, I, SECAM-B/G,D/K, I, L/L’,
NTSC4.43MHz
CS PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43/3.58MHz
WARNING: TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
☛
The main voltage is indicated on the rear
of the TV set and the frequency is 50 or
60Hz.
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
!
10%
H
5°
75%
35°
H
3
ENG
Contents
◆ PREPARING YOUR TELEVISION
■
Safety Instructions ......................................................................................... 2
■
Caution .......................................................................................................... 2
■
Front Control Panel ....................................................................................... 4
■
Connection Panels ........................................................................................ 5
■
Infrared Remote Control (All Functions Except Teletext) .............................. 6
■
Infrared Remote Control (Teletext Functions) ............................................... 7
■
Inserting the Batteries in the Remote Control................................................ 8
■
Connecting the Aerial (or Cable Television Network).................................... 8
■
Switching Your Television On and Off........................................................... 9
■
Placing Your Television in Standby mode..................................................... 9
■
Plug & Play Feature....................................................................................... 10
■
Viewing the Demonstration............................................................................ 11
■
Choosing Your Language.............................................................................. 12
◆ SETTING UP THE CHANNELS
■
Storing the Channels Automatically............................................................... 13
■
Storing the Channels Manually...................................................................... 14
■
Giving Channels Names................................................................................ 16
■
Skipping Unwanted Channels ....................................................................... 17
■
Fine tuning Channel Reception ..................................................................... 18
■
Sorting the Stored Channels ......................................................................... 19
◆ USING THE TELEVISION
■
Changing the Picture Standard ..................................................................... 20
■
Adjusting the Picture Settings........................................................................ 21
■
Selecting the Picture Format (depending on the model) ............................... 21
■
Activation/Deactivation the Digital Noise Reduction Feature ........................ 22
■
Changing the Sound Standard ...................................................................... 23
■
Adjusting the Sound Settings ........................................................................ 24
■
Extra Sound Settings (depending on the model)........................................... 25
■
Selecting the Sound Mode (depending on the model) .................................. 26
■
Selecting the Turbo Sound............................................................................ 27
■
Adjusting the Volume..................................................................................... 27
■
Switching the Sound Off Temporarily ............................................................ 27
■
Setting the Sleep Timer ................................................................................. 28
■
Setting and Displaying the Current Time....................................................... 28
■
Switching the Television On and Off Automatically ....................................... 29
■
Setting the Blue Screen Mode....................................................................... 30
■
Activating the Childlock ................................................................................. 30
◆ USING THE TELETEXT FUNCTION
■
Teletext Decoder ........................................................................................... 31
■
Displaying Teletext Information ..................................................................... 31
■
Selecting a Specific Teletext Page................................................................ 32
■
Using FLOF to Select a Teletext Page .......................................................... 33
■
Storing Teletext Pages .................................................................................. 33
◆ INFORMATION ON CONNECTIONS AND RECOMMENDATIONS FOR USE
■
Connecting to the AV-1 or 2 Input/Outputs.................................................... 34
■
Connecting to the Rear S-VIDEO Input......................................................... 35
■
Connecting to the Rear DVD Input................................................................ 35
■
Connecting to the RCA Input......................................................................... 36
■
Connecting Headphones............................................................................... 37
■
Viewing Picture From External Sources ........................................................ 37
■
Automatic Degaussing to Remove Colour Patches....................................... 38
■
Trouble Shooting: Before Contacting Service Personnel .............................. 38
☛
➢
Symbols
Press Important Note
4
ENG
Front Control Panel (depending on the model)
➣
Buttons and markings are subject to change.
TV/VIDEO
SELECTION
MENU DISPLAY
VOLUME ADJUSTMENT
CHANNEL SELECTION
POWER
STAND-BY/TIMER
INDICATOR
REMOTE CONTROL SENSOR
MENU DISPLAY
VOLUME ADJUSTMENT
CHANNEL SELECTION
POWER
STAND-BY/TIMER
INDICATOR
REMOTE CONTROL SENSOR
TV/VIDEO
SELECTION
MENU DISPLAY
VOLUME ADJUSTMENT
CHANNEL SELECTION
POWER
STAND-BY INDICATOR
REMOTE CONTROL
SENSOR
TIMER
INDICATOR
5
ENG
Connection Panels
HEADPHONE JACK
(OPTION)
INPUT 1
MONITOR
-OUT
INPUT 2
VIDEO
(
MONO
)
L-AUDIO-R
Side of TV
Rear of TV
RCA AUDIO/VIDEO
INPUT CONNECTORS
Front of TV
HEADPHONE JACK (OPTION)
RCA AUDIO/VIDEO
INPUT CONNECTORS
☛
This figure shows the Standard Connector-jack panel.
The actural configuration on your TV may be different,
depending on the model.
DVD INPUT CONNECTORS
(OPTION)
S-VIDEO CONNECTOR
(OPTION)
RCA AUDIO/VIDEO
INPUT/OUTPUT CONNECTORS
RGB
2
1
SCART AUDIO/VIDEO
INPUT/OUTPUT
CONNECTORS
OPTION
INPUT
MONITOR
-OUT
VIDEO AUDIO
RCA AUDIO/VIDEO
INPUT/OUTPUT CONNECTORS
6
ENG
Infrared Remote Control (All Functions Except Teletext)
➣
Operation of remote control may be affected by bright artificial light near to the TV set.
POWER
SOUND MENU DISPLAY
(OPTION)
ONE/TWO-DIGIT CHANNEL
SELECTION
TURBO SOUND ON/OFF
(OPTION)
TEMPORARY SOUND SWITCH-
OFF
VOLUME DECREASE
PREVIOUS CHANNEL
DIRECT CHANNEL SELECTION
TUNER/CABLE NETWORK
SELECTION
EXTERNAL INPUT SELECTION
ON-SCREEN DISPLAY
AUTOMATIC SWITCH-OFF
PICTURE SIZE
NEXT CHANNEL
VOLUME INCREASE
PICTURE STANDARD
SOUND STANDARD (OPTION)
SOUND MODE SELECTION
(OPTION)
MENU DISPLAY
➣
Buttons and markings are subject to change.
7
ENG
Infrared Remote Control (Teletext Functions)
TELETEXT HOLD
FASTEXT TOPIC SELECTION
TELETEXT NEXT PAGE
TELETEXT PREVIOUS PAGE
TELETEXT DISPLAY/MIX
LIST/FLOF MODE SELECTION
TELETEXT REVEAL
TELETEXT STORE
PICTURE SIZE
TELETEXT SUB-PAGE
PROGRAMME SELECTION
BY NAME
➣
Buttons and markings are subject to change.
?
1
1
8
ENG
You must insert or replace the batteries in the remote control when
you :
◆ Purchase the television.
◆ Find that the remote control is no longer operating
correctly.
1 Remove the cover of the remote control by pressing the symbol
( ) and pulling the cover in the direction of the arrow.
2 Insert batteries, taking care to respect the polarities:
◆ + on the battery with + on the remote control
◆-on the battery with -on the remote control
3 Replace the cover by pushing it in the direction of the arrow.
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
Plug the aerial or cable network input cable to the 75Ω coaxial socket
on the rear of the television.
Inserting the Batteries in the Remote Control
Connecting the Aerial (or Cable Television Network)
Cable
Television
Network
Rear of TV
PRESS
PRESS
PRESS
9
ENG
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the TV set and
the frequency is 50 or 60Hz.
2 Press the “” (ON/OFF) button on the front of the television.
Result
: The Standby indicator lights up on the front panel.
3 Press the POWER button on the remote control to switch the
television on.
Result
: The programme that you were watching last is re-
selected automatically.
4 To switch your television off, press the “” (ON/OFF) button
again on the front of the television.
Placing Your Television in Standby mode
Your television can be placed in Standby mode, in order to reduce:
◆ Power consumption
◆ Wear of the cathode ray tube
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
The television is placed automatically in Standby mode when you
turn it on.
1 Press the POWER button on the remote control.
Result:
The screen is turned off and the Standby indicator on
the front of the television lights up.
2 To switch the screen back on, simply press the POWER button
again on the remote control.
➣
Do not leave your television in standby mode for long
periods of time (when you are away on holiday, for example).
In this case, you should switch it off completely.
Switching Your Television On and Off
10
ENG
Plug & Play Feature
When the television is initially powered ON, three basic customer
settings proceed automatically and subsequently: setting the
language, channel and clock.
1 If the television is in Standby mode (red light visible on the
television front panel), press the POWER button on the remote
control.
Result: The message “Plug & Play” is displayed. It flickers for a
little while and then the “Language” menu is
automatically displayed.
2 Press the ▲ or ▼ button to select required language. Press the
MENU button to enter the language, and then the message “Ant.
Input : Check” is displayed.
➣
If any language is not selected on the “Language” menu, the
“Language” menu will be displayed about 30 seconds later.
3 Make sure that the antenna is connected to the TV. And then press
the + or – button.
Result: The “Auto store” menu is displayed.
4 Select your country by pressing the + or – button. To search the
channels, select the “Search” by pressing the ▲ or ▼ button, and
then press the + or – button (refer to “Storing the Channels
Automatically” on page 13). Press the MENU button to skip.
Result: The “Time” menu is displayed.
5 Press the + or – button to move to the hour or minute. Set the hour
or minute by pressing the ▲ or ▼ button (refer to “Setting and
Displaying the Current Time” on page 28).
6 When you have finished, press the MENU button.
Result: The message “ENJOY YOUR WATCHING” is displayed,
and then the channel which has been stored will be
activated.
7 If you want to reset this feature...
1 Press the MENU button.
2 Press the ▲ or ▼ button to select the “Function”, and then
press the + or – button.
3 Select the “Plug & Play” by pressing the ▲ or ▼ button, and
then press the
+ or – button.
Result:
The message “Plug & Play” is displayed.
Plug & Play
Ant. Input : Check
Select Exit
Auto store
Area : ASIA W/EUROPE
Search : -/+
Select Adjust Exit
Time
Clock : -- : -- am
Timer : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
11
ENG
Viewing the Demonstration
To become familiar with the various menus provided by your
television, you can view the inbuilt demonstration.
1 Press the MENU button.
2 Press the ▲ or ▼ button to select the “Function” and press the + or
– button.
3 Press the ▲ or ▼ button to select the “Demonstration” and press
the + or – button.
Result: Each of the menu options is displayed in turn.
4 When you wish to stop the demonstration, press any button on the
remote control.
Picture
Mode Custom
Adjust
Digital NR : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
12
ENG
Choosing Your Language
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
1 Press the MENU button.
2 Press the ▲ or ▼ button to select the “Function”.
3 Press the + or – button to select the “Language”.
4 Select a particular language by pressing the ▲ or ▼ button
repeatedly.
5 When you have finished, press the TV button or, press the
MENU button repeatedly to return to normal viewing.
Picture
Mode Custom
Adjust
Digital NR : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Adjust Exit
Loading...