Samsung CS-53140TS, CS-21K40MG User Manual

COLOR TELEVISION

CS21K40

Owner’s Instructions

Before operating, please read this manual thoroughly,

and retain it for future reference.

www.samsung.com/global/register

Connection Panel

The actual configuration of your TV may be different,

➢

depending on your model.

Rear Panel

(depending on the model)

Connecting to the RCA Output

The RCA4 connectors are used for equipment, such as a recording VCR or audio system.

Connecting to the RCA Input

The RCA3 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. (When using the mono equipment, connect to the AUDIO-L input connector.)

The RCA5 connectors are used for equipment such as a DVD with component output (480i only).

Control Panel

The actual configuration of your TV may be different,

➢

depending on your model.

Front (or Side) Panel

1 On-screen menu display 2 Volume adjustment 3 Channel selection 4 Remote control sensor 5 Standby indicator 6 Power on/off

◆ You can use the 3 buttons to switch the TV on when it is

in standby mode depending on the model.

◆ The 2 and 3 buttons also have the same function as the

œ/√/†/… buttons on the remote control.

◆ If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.

(depending on the model)

cable television

network

Whenever you connect an audio or video system to your

☛

television, ensure that all elements are switched off. Please be sure to match the color coded input terminals and cable jacks.

Connecting to an Aerial or Cable Television Network

Connect the aerial or network input cable to the 1 (75 Ω coaxial socket). To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network. If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.

Connecting to the SCART Input/Output

The SCART2 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. The SCART2 is also used for equipment with an RGB output, such as a video game device or video disc player.

Front (or Side) Panel

Audio input

Video input

Headphone jack

Please be sure to match the color coded input terminals

☛

and cable jacks.

Connecting to the RCA Input

The 1 (AUDIO-L/R) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video disc player, or video game device.

Connecting Headphones

The 3 (headphone) jack is used for watching a television programme without disturbing the other people in the room. Prolonged use of headphones at a high volume may damage your hearing.

When both the front (or side) AV and rear connectors

➢

are connected to external equipment, the front (or side) AV receives priority.

English - 1

continued...

AA68-03808E-01

Remote Control

Operation of remote control may be affected by bright

➢

artificial light near to the TV.

(depending on the model)

66 …… / †† / œœ / √√

Used to increase or decrease the volume.

Used to display the onscreen menu or return to the previous menu.

Used to control the cursor in the menu.

S.MENU

Used to display the sound menu.

TURBO

Used to select the turbo sound option.

P.SIZE

Used to change the screen size.

DUAL I-II (option) Used to select the sound mode.

SOURCE

Used to display all of the available video sources.

INFO

Used to view the channel information and setting status you selected.

PRE-CH

Used to switch repeatedly between the last two channels displayed.

Used to display the next or previous stored channel.

EXIT

Used to exit from any display or return to normal viewing.

MUTE

Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or

button.

ENTER

While using the onscreen menus, press the ENTER button to activate (or change) a particular item.

S.MODE (option) Used to select the sound effect.

((

P. MODE

Used to select the picture effect.

))

Used to return to the TV mode when it is in external input mode.

SLEEP

Used to select a preset time interval for automatic shut off.

Switching the Television On and Off

The mains lead is attached to the rear of the television.

1 Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the

➢

television and the frequency is 50 or 60Hz.

2 Press the “I” button (On/Off) on the front (or side) of the

television.

3 Press the POWER button on the remote control to

switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” or “Channel - Manual Store” on page 4.

If the television is initially powered on, several basic

➢

customer settings proceed automatically. Refer to “Function - Plug & Play” on page 3.

4 To switch the television off, press the “ I ” button (On/Off)

on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER button on the remote control while

viewing. The television is in standby mode.

2 To switch the television back on, simply press it again.

POWER

Used to switch the TV on and off.

Numeric buttons

Used to select channels directly.

-/--

Used to select a channel numbered ten or over. Press this button, then “--” symbol is displayed. Enter the two-digit channel number.

Installing Batteries

Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+” and “-” ends of the batteries are inserted correctly or the batteries are drained.

Do not mix battery types, i.e. alkaline and manganese.

➢

English - 2

Do not leave the television in standby mode for long

☛

periods of time (when you are away on holiday, for example). Turn the television off by pressing the “I ” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.

Viewing the Menus

Function - Plug & Play

1 Press the MENU button.

The main menu is displayed on the screen. Its left side has four icons: Picture, Sound, Channel, and Function.

2 Press the … or † button to select one of the icons.

Press the œ or √ button to access the icon’s sub-menu.

3 Press the … or † button to move to items in the menu.

Press the œ or √ button to enter items in the menu.

4 Press the …/†/œ/√ button to change the selected

items. Press the MENU button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in standby

Plug & Play

mode, press the POWER button on the remote control. The Plug & Play is displayed. It flickers for a little while, and then Language menu is displayed.

2 Select the appropriated

language by pressing the … or † button. Press the MENU button. The Ant. Input Check is displayed.

If any language is not

➢

selected, the language

LANGUAGE ENGLISH

FRANÇAIS TÜRKÇE

Adjust Select

Ant. Input Check

Auto Store Exit

menu will disappear about 30 seconds later.

3 Make sure that the antenna is connected to the

television (refer to page 1).

4 Press the œ or √ button to

search the channels. The

P 1 471 MHz 48%

searching starts. To stop the search, press the MENU

Exit

button.

continued...

5 When the channel

searching has finished, the Time menu is displayed with Clock selected.

Time

Clock -- : -- am

Move Exit

6 Press the œ or √ button to move to the hour or minute.

Set the hour or minute by pressing the … or † button.

7 When you have finished,

ENJOY YOUR WATCHING

press the MENU button. The ENJOY YOUR WATCHING is displayed, and then the channel which has been stored will be activated.

Re-setting the Plug & Play

Method: MENU ➜ …/† (Function) ➜ œ/√ ➜ …/† (Plug & Play) ➜ œ/√

Language : English Time

Plug & Play

Blue Screen : Off Child Lock Low Noise Amp : Off

Select Enter Exit

Function

√√

English - 3

+ 5 hidden pages