SAMSUNG CS-15K8MNQ, CS-15M16MJQ, CS-21M16MQQ Service Manual Alignment & Adjustment

Alignment and Adjustments
4-1
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the Video Mode.
3. Do not tamper with the “Adjustment” screen of the Factory Mode menu. This screen is intended only for factory use.
4-1-2 When EEPROM (IC902) Is Replaced
1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to re-program this data.
2. After IC902 is replaced, warm up the TV for 10 seconds.
4-1-3 When CRT Is Replaced
1. Make the following adjustments AFTER set­ting up after setting up purity and conver­gence :
White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size Fail Safe (This adjustment must be the last step).
2. If the EEPROM or CRT is replaced, set PVAto 40 (factory mode) and set SC as follows.
4-2 Factory/Service Mode
4-2-1 Procedure for the “Adjustment” Mode
1. This mode uses the standard remote control. The Service Mode is activated by entering the following remote-control sequence :
(1) DISPLAY→FACTORY. (2) STAND-BY→ DISPLAY→ MENU→ MUTE
POWER ON.
2. The “SERVICE (FACTORY)” message will be displayed. The Service Mode has three compo­nents: ADJUST , OPTION,OPTION1,G2 Adjust and Reset.
3. Access the Adjustment Mode by pressing the “VOLUME” keys ( Up or Down). The adjust­ment parameters are listed in the accompany­ing table, and selected by pressing the CHAN­NEL keys (▲ ,).
4. Selection sequences for the all system:
DOWN or UP key:
AGC>SCT>SBT>BLR>BLB>RG>GG>BG> VSL>VS>VA>HS>SC>CDL>STT>AKB> PDL>NDL>PSR>NSR>VOL>LCO>TXP> MVOL>FMWS>AGCS>OMD>SCL>PWL>
AGN>PEK>ACL>FCO>SCBT>SSP>PSNS
5. The VOLUME keys increase or decrease the adjustment values (stored in the non-volatile memory) when Adjustment Mode is cancelled.
6. Cancel the Adjustment Mode by re-pressing the “FACTORY” or “Power OFF” keys.
4-2-2 Main Adjustment Parameter
Alignment and Adjustments
4-2
Samsung Electronics
OSD FUNCTION RANGE INITIAL DATA REMARK AGC RF AGC 0 … 63 33 SCT Sub contrast 0 … 23 13 SBT Sub brightness 0 … 23 9 BLR Black level offset R 0 … 63 31 BLB Black level offset B 0 … 63 27
RG White point R 0 … 63 32 GG White point G 0 … 63 32(FIX) BG White point B 0 … 63 31
VSL Vertical slope 0 … 63 19
VS Vertical shift 0 … 63 38 VA Vertical amplitude 0 … 63 40(FIX) HS Horizontal shift 0 … 63 30
SC S-correction 0 … 63 24 CDL Cathode drive level 0 … 15 12 STT Sub tint 0 … 7 7 AKB Black current stabilization 0 … 1 0 PDL PAL delay 0 … 15 1 NDL NTSC delay 0 … 15 10 PSR PAL sub color 0 … 23 15 NSR NTSC sub color 0 … 23 10 VOL Volume pre setting 0 … 63 10 LCO SECAM-L Vision IF 0 … 1 0 TXP TTX Position 0 … 15 9
MVOL Melody initial volume adjustment 0 … 50 10 FMWS Narrow-band sound PLL window selection 0 … 1 0 AGCS IF AGC speed 0 … 3 1
OMD Off-set IF demodulator 0 … 63 26 SCL Soft clipping level 0 … 3 1 PWL Peak white limiting 0 … 15 12 AGN FM demodulator gain 0 … 1 1 PEK Peaking center frequency 0 … 3 2 ACL Automatic color limiting 0 … 1 0 FCO Forced color limiting 0 … 1 0
SCBT Screen brightness 0 … 63 45
SSP Sub Sharpness gain adjustment 0 … 23 20
PSNS Identify sensitivity PAL/NTSC decoder 0 … 1 1
Alignment and Adjustments
Samsung Electronics 4-3
4-2-3 Option Bytes
In the Service Mode, various can be selected via the Option Table. Example:
Option Table:XX XX XX XX
1 LNA ON
2 SYSTEM CZ
3 AUDIO STEREO
4 JACK
SCART
5 ZOOM NOR/ZOOM/16:9
6 AUTO POWER ON
7 SBL OFF
8 2nd SIF ON
9 HOTEL MODE OFF
10 BKS ON
11 HIGH DEVIA ON
12 HELP MENU ON
13 TIME ON
14 V-GUARD OFF
Alignment and Adjustments
4-4 Samsung Electronics
4-3 Other Adjustments
4-3-1 General
1. Usually, a color TV needs only slight touch­up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus.
2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, per­form the purity and convergence adjustments described below.
3. Use the specified test equipment or its equiva­lent.
4. Correct impedance matching is essential.
5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results.
6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
8. To protect against shock hazard, use an isola­tion transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the pic­ture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.
The degaussing coil operates for about 1 sec­ond after the power is switched ON. If the set has been moved or turned in a different direc­tion, disconnect its AC power for at least 30 minutes.
If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
4-2-4 RESET
The Reset Mode is used during factory inspection. Function Reset:
1. Picture Custom
2. Auto Volume Off
3. Color System Auto (option)
4. Sound System D/K (option)
5. Blue Screen Off
6. Low Noise AMP Off (option)
7. Volume 10
8. CH. Skip Erased
9. CH. Lock Off
10. Timer Off
Alignment and Adjustments
Samsung Electronics 4-5
4-3-3 High Voltage Check
CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +125 volts (Full color bar input and normal picture level).
1. Connect a digital voltmeter to the second
anode of the picture tube.
2. Turn on the TV. Set the Brightness and
Contrast controls to minimum (zero beam cur­rent).
3. The high voltage should not exceed 27.5KV.
4. Adjust the Brightness and contrast controls to
both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions.
4-3-4 FOCUS Adjustment
1. Input a black and white signal.
2. Adjust the tuning control for the clearest pic-
ture.
3. Adjust the FOCUS control for well defined
scanning lines in the center area of the screen.
4-3-5 Cathode Voltage Adjustment
(Screen Adjustment)
1. Connect CRT socket pin GK to an oscilloscope
probe.
2. Input a gray scale pattern. (Use a pattern gen-
erator, PM5518)
3. Use the P mode key (on the remote control)
for the STANDARD picture.
4. Adjust the Screen VR (on the FBT) so that the
voltage on the oscilloscope becomes 120+2.5V (See Fig. 4-1).
4-3-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Plug in the CRT deflection yoke and tighten the clamp screw.
3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2.
4. Input a black and white signal.
5. Fully demagnetize the receiver by applying an external degaussing coil.
6. Turn the CONTRAST and BRIGHTNESS con­trols to maximum.
7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to pro­vide vertical green belt. (Fig. 4-3).
8. Tighten the convergence yoke.
9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.
10. Temporarily tighten the deflection yoke.
11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field.
12. Tighten the deflection yoke.
or
œ
or
1. Input a gray scale pattern.
(Use a pattern generator,PM5518)
2. Enter "Adjustment" Mode:
(1) DISAPLAY FACTORY
(2) STAND-BY DISAPALY MENU
MUTE POWER ON
3. Select "G2 adjust" by pressing channel key
4. Enter "G2 adjust" by pressing channel key
5. Adjust he screen Vr (On the FBT),so that OSD becomes "SCREEN ADJEST:OK"
4-3-5 Cathode Voltage Adjustment
(Screen Adjust)
Alignment and Adjustments
4-6 Samsung Electronics
4-3-7 White Balance Adjustment
Fig. 4-2 Convergence Magnet Assembly
Fig. 4-3 Center Convergence Adjustment
Fig. 4-4
(a) Set up
1. Warm up the TV for at least 30 minutes in the Aging Mode (OSD White). This mode is dis­played by entering the following sequence:
DISPLAY
FACTORY → FACTORY
2. Input a Toshiba pattern.
(b) Low-Light Adjustment
1. Set SBT to 3.5 ± 0.5 fL in the Factory Service Mode with using CA100. See Fig. 4-4
➁.
2. Adjust RG,BG so that the levels are suitable to each local area.
(c) High-Light Adjustment
1. Set SCT to 55 FL (20”. 21”), 65 FL(14”) in the
Factory Service Mode with using CA100. See Fig. 4-4
①.
50 21"flat in the Factory Service Mode with using CA100.See Fig.4-4 1 .
2.5
6 Pole Magnet
Clamper
Screw
4 Pole Magnet
2 Pole Magnet
2 POLE PURITY
Vertical Green Belt
6 POLE
CONVERGENCE 4 POLE CONVERGENCE
YOKE CLAMP SCREW
ADJUST THE ANGLE (VERTICAL LINES)
31m/m
1
2
Alignment and Adjustments
Samsung Electronics 4-7
4-3-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen.
3. Adjust the Brightness and Contrast controls for a well defined picture.
4. Adjust the two-tab pairs of the 4 pole mag­nets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen.
5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen.
6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.)
7. Repeat adjustments 2~6, if necessary.
8. Since the 4-pole magnets and 6-pole magnets
interact, the dot movement is complex (Fig. 4-5).
Fig. 4-5 Center Convergence Adjustment
BLUE
BLUE
RED
RED
RED/BLUE
RED/BLUE
GREEN
GREEN
4-Pole Magnet Movement
6-Pole Magnet Movement
Alignment and Adjustments
4-8 Samsung Electronics
24(21"flat)
4-3-9 RF AGC Adjustment
Set the AGC data to 33 (Factory Mode).
4-3-10 Sub-Color Adjustment
PSR
Set data to (Factory Mode).
NSR
2 5
4-3-11 Geometry Adjustment
SC
VSVSLHS
1. Input a lion head pattern (in the PAL channel).
2. Set the SC (S-Correction) as follows : 9 (21”),
9 (20”), 0 (14”) and VA 40 so that the lion
head circle becomes oval.
3. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4.
4
5
5
Fig. 4-9
6. Adjust HS (using the width coil) so that the left and right margins of the picture are 5.
Fig. 4-7
4. Adjust with VS (Vertical shift) so that the top margin of the picture is 4.
4
Fig. 4-8
5. Adjust with HS (Horizontal Shift) so that the
lion-head pattern and CRT centers are aligned.
Loading...