Samsung CE745GR User Manual

MICROWAVE OVEN

CE745GR

SERVICE

Manual

MICROWAVE OVEN

CONTENTS

1. Precaution

2. Specifications

3. Operating Instructions

4. Disassembly and Reassembly

5. Alignment and Adjustments

6. Troubleshooting

7. Exploded Views and Parts List

8. PCB Diagrams

9. Schematic Diagrams

BWT

GRILL

CE745GR

lbs. kg

oz. g

1min+

h

10min

min 1min

1-2-3

Auto

10s.

Samsung Electronics

(a) Do not operate or allow the oven to be operated

with the door open.

(b) Make the following safety checks on all ovens

to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and

other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.

(c) Before turning on microwave power for any

service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.

(d) Any defective or misadjusted components in

the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.

(e) A Microwave leakage check to verify

compliance with the Federal performance standard should be performed on each oven prior to release to the owner.

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

1. Precaution

1-1 Safety precautions ( )

Samsung Electronics 1-1

1. All repairs should be done in accordance with the procedures described in this manual. This product complies with Federal Performance Standard 21 CFR Subchapter J (DHHS).

2. Pacemaker wearers must consult a physician before attempting to service an MWO.

8. Notify the Central Service Center if the microwave leakage exceeds 5 mw/cm

2

4. Check all grounds.

5. Do not power the MWO from a "2-prong" AC cord. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

6. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

7. Make sure that there are no cabinet openings through which people--particularly children--might insert objects and contact dangerous voltages. Examples: Lamp hole, ventilation slots.

8. In the event of suspected microwave energy leakage in excess of 5mW/§†, please notify

J.V.SAMSUNG SERVICE LTD. MARSHAL ZHUKOU.,1.OFFICE 201 123308,MOSCOW,RUSSIA

9. Service technicians should remove their watches while repairing an MWO.

10. To avoid any possible radiation hazard, replace parts in accordance with the wiring diagram. Also, use only the exact replacements for the following parts: Primary and secondary interlock switches, interlock monitor switch.

11. If the fuse is blown by the Interlock Monitor Switch: Replace all of the following at the same time: Primary and secondary switches, as well as the Interlock Monitor Switch. The correct adjustment of these switches is described elsewhere in this manual. Make sure that the fuse has the correct rating for the particular model being repaired.

12. Design Alteration Warning: Use exact replacement parts only, i.e., only those that are specified in the drawings and parts lists of this manual. This is especially important for the Interlock switches, described above. Never alter or add to the mechanical or electrical design of the MWO. Any design changes or additions will void the manufacturer's warranty.10.Always unplug the unit's AC power cord from the AC power source before attempting to remove or reinstall any component or assembly.

13. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

14. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs). Examples include integrated circuits and field-effect transistors.

Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground.

15. Always connect a test instrument's ground lead to the instrument chassis ground

before

connecting the positive lead; always remove the instrument's ground lead last.

Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially lethal high voltages and currents.

16. When checking the continuity of the witches or transformer, always make sure that the power is OFF, and one of the lead wires is disconnected.

17. Components that are critical for safety are indicated in the circuit diagram by shading, or .

18. Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

1. High Voltage Warning Do not attempt to measureany of the high voltages--this includes the filament voltage of the magnetron. High voltage is present during any cook cycle.

Before touching any components or wiring, always unplug the oven and discharge the high voltage capacitor (See Figure 1-1)

2. The high-voltage capacitor remains charged about 30 seconds after disconnection. Short the negative terminal of the high-voltage capacitor to the oven chassis. (Use a screwdriver.)

3. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

1-2

Pretaution

Samsung Electronics

1-2 Special Servicing Precautions (Continued)

1-3 Special High Voltage Precautions

Fig. 1-1. Discharging the High Voltage Capacitor

2. Specifications

2-1 Table of Specifications

ITEM TIMER 99 MINUTES 90 SECONDS POWER SOURCE 230V/50HZ, AC POWER CONSUMPTION MICROWAVE : 1,400W,GRILL : 1100W OUTPUT POWER FROM85 TO 850W (10 LEVEL POWER)

OPERATING FREQUENCY 2,450MHz MAGNETRON OM75PH(31) COOLING METHOD COOLING FAN MOTOR OUTSIDE DIMENSIONS 191/4"(W) x 1027/32"(H) x 143/8"(D) NET WEIGHT 36.3 LBS. SHIPPING WEIGHT 39.6 LBS.

MODEL CE745GR

(IEC-705 TEST PROCEDURE)

2-2 Comparison Chart

MODEL

FEATURE

MORE/LESS O

AUTO REHEAT O AUTO DEFROST O TIME COOK O POWER LEVEL O INSTANT COOK O MEMORY O BOOST CHILD LOCK O CLOCK O GRILL O COMBI O

CE745GR

Samsung Electronics 2-1

CE745GR

lbs.

kg

oz.

g

1min+

h

10min

min

1min

1-2-3

Auto

10s.

Auto Defrost Butten

Kg,g Button

Power Level Selection Button

Memory Button

Hold/Timer Button

Stop Button Start/Boost Button

Timer Setting Button

Grill Button Combi Button

Clock Setting Button

More/Less Button

Auto Cook Button

Instant Cook Button

3. Operating Instructions

3-1 Control Panel

Samsung Electronics 3-1

3-2 Features & External Views

,,,,,,,,,,,,,,,,,

Door

Ventilation Slot Light

Safety Interlock Holes

Control Panel

Open Door Push Button

Guide Roller

GRILL WIRE RACK

Glass Plate

Door Latches

CE745GR

lbs. kg

oz. g

1min+

h

10min

min 1min

1-2-3

Auto

10s.

489mm

357mm

275mm

200mm

365mm

GRILL

CE745GR

lbs. kg

oz. g

1min+

h

10min

min 1min

1-2-3

Auto

10s.

4. Disassembly and Reassembly

4-1 Replacement of Magnetron, Motor Assembly and Lamp

Samsung Electronics 4-1

Remove the magnetron including the shield case, permanent magnet, choke coils and 500pF capacitors (all of which are contained in one assembly).

1. Disconnect all lead wires from the magnetron and lamp.

2. Remove the bracket mounting.

3. Remove the air cover.

4. Remove screws securing the magnetron to the wave guide.

5. Take out the magnetron very carefully.

6. Remove screws from the back panel.

7.Remove the assy noise filter.

8. Take out the fan motor.

9. Remove the oven lamp by pulling out from hole of air cover carefully.

10. NOTE1: When removing the magnetron, make

sure that its antenna does not hit any adjacent parts, or it may be damaged.

11. NOTE2: When replacing the magnetron, be

sure to remount the magnetron gasket in the correct position and make sure the gasket is in good condition.

1. Discharge the high voltage capacitor.

2. Disconnect all the leads.

3. Remove the mounting bolts.

4. Reconnect the leads correctly and firmly.

4-2 Replacement of High Voltage Transformer

Lamp

Cover Air

Magnetron

H. V. Trans

H. V. Capacitor

Screw

Thermo S/W

Fan Motor

H. V. Trans

Bolts

BKT-Mountain

PRECAUTION

Servicemen should remov their watches whenever

working close to or replacing the magnetron.

PRECAUTION

There exists HIGH VOLTAGE ELECTRICITY with high current capabilities in the circuits of the HIGH VOLTAGE TRANSFORMER secondary and filament terminals. It is extremely dangerous to work on or near these circuits with the oven energized. DO NOT measure the voltage in the high voltage circuit including filament voltage of magnetron.