Samsung b25, S25, B24, S26, S27 Disassemble
...
67
13. Disassembly method of the refrigerator
13-1) How to disassemble the freezer and refrigerator
FTA / DTA
Ice-maker
Interior Lamp(FRE)
While supporting the ice-maker at front, lift
it slightly toward direction and pull it
straight out toward direction.
While pushing toward direction using(-) driver
or the likes, make the lamp cover free.
Remove the lamp cover by pulling it down toward
direction while holding the back of the cover.
After replacement of the lamp, push the font of the
lamp cover back and then the back.
Case-Baskel and Tray Ice
After removing the Case-Basket by pulling it
out, pull the Tray Ice out.
Cover-Tray Water
After opening the doors of the freezer and
refrigerator, disassemble the Cover-Tray Water by
turnig three screws.
When assembling
the Cover-Tray
Water, make it fit
to three slots and
assemble by
turning three
screws.
Case-Veg(LOW) and its cover
Disassemble it by drawing it and lifting it
up slightly while holding the knob. ( )
Slide the cover out by pulling it to the
front. ( )
Case-Veg(UPP) and its cover
Disassemble it by drawing it and lifting it up
slightly while holding the knob. ( )
Slide the cover out by pulling it to the front.
( )
Interior Lamp(REF)
Remove the cover by rotating( ) driver.
Remove the lamp by pulling it out and replace new one.
After covering, assemble by rotating( ) driver toward the arrow direction.
Guide-Bottle(REF)
While holding the Guide-Bottle, disassemble
it by lifting it up.
Shelf(REF)
While drawing the shelf out, slide it out by
lifting it up.
Cover-Guard
While pushing the cover to the left, slide it
out by lifting it up.
68
13-2) Disassembly of Evaporator of Freezer
1. After disassembly of the lamp cover for the
freezer, disconnect wire housing from the
lamp socket.
2. Disassemble and remove two cap-screws
using(-) driver or the likes.
3. While holding the bottom of the EVAPCOVER FRONT and drawing it carefully
toward the arrow direction, disassemble
the cover by sliding it out at the raised
spot.( Since the housing for the thermalsensor is located at the rear side of the
cover, be careful during disassembly and
disconnect the housing.)
4. After disassembly of the EVAP-COVER
REAR, disassemble the motor and heater
housing from the wire terminal at the top
side of the cover.
5. After removing two screws of the COVEREVAP REAR, disassemble it by pulling it
out to the front using(-) driver or the likes.
( Slide the cover out by pushing the held
part toward the arrow direction and
drawing it to the front )
13-3) Disassembly of Evaporator of Refrigerator
1. Remove all foods in the refrigerator and
shelves.
Disassemble two purifier covers using(-)
driver or the likes and remove a screw.
2. Detach snaps of the bottom side of the
COVER-EVAP FRONT by inserting(-)
driver into the snaps and rotating it toward
the arrow direction.
After detachment of the snaps of the EVAPCOVER FRONT, disassemble the cover by
pulling it to the front.
3. After detachment of the insulating material,
remove screw of damper cover and
disassemble by pulling it to the front.
( While disassembling the damper cover,
at first disassemble the sensor housing at
the left top.)
4. Disassemble the COVER-EVAP REAR by
deatching the snaps and pulling it out to
the front using(-) driver or the likes.
( While disassembling the COVER-EVAP
REAR, be careful because motor wire is
connected.)
5. Disassemble the motor and heater housing
from the wire terminal at the top side of the
cover.
Loading...