The following safety precautions must be taken when installing
and using your air conditioner.
1
The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2
Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
3
NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
4
Do NOT insert anything between the air outlet blades, as it may damage the inner fan
and you may get hurt. Keep children away from the unit.
5
If the supply cord is damaged, it must be replaced by the manufacturer
or similarly qualified persons in order to avoid a hazard.
6
Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
An authorized service center
The dealer from whom you purchased the air conditioner
.
,
its service agent
E-2
7
Do NOT place any blocking objects in front of the unit.
8
If the remote control will not be used for a long time, remove the batteries.
9
Before throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely
10
The appliance is not intended for use by young children or infirm person without supervision;
young children should be supervised to ensure that they do not play with the appliance.
11
Do NOT use an extension cord with this product.
CCCCAAAAUUUUTTTTIIIIOOOONN
NN
.
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
Power plug (The type of
power plug may differ,
depending on the local
power supply.)
Temperature/Timer
settings
Temp.
Temperature adjustment
buttons
Swing
Power
On/Off button
Fan speed adjustment buttonRemote control sensor
E-
4
Remote Control - Buttons and display
Remote control
transmission indicator
Operating mode
( Cool, Dry, Fan)
Temperature setting
Sleep mode
Energy Saving mode
Fan speed
Air flow direction
On Timer setting
Off Timer setting
Battery discharge indicator
Mode selection button
(Cool, Fan, Dry)
Temperature adjustment
buttons
Sleep timer setting button
Fan speed adjustment
button
Energy Saving button
Timer setting button
Timer Set/Cancel button
Air flow blade swing button
On/Off button
E-
5
Getting Started
You have just purchased a Samsung window-type r oom air conditioner which should be installed
following your installation manual.
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to r ead them as they will help you take full advantage of the unit’ s features.
The booklet is organized as follows.
The following figures are shown on pages 4 and 5:
-Description of Each Component
-Remote control (buttons & display)
They will help you find the buttons and understand the symbols displayed.
In the manual, you will find a series of step-by-step pr ocedures for each function
available.
The illustrations in the step-by-step procedures use four different symbols:
PRESSPUSHIMPORTANTNOTE
E-
6
E-
7
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
You purchase the air conditioner
The remote control does not work correctly
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
Push the battery cover on the rear of the remote control with your thumb
1
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities :
2
+ on the battery with + on the remote control.
- on the battery with - on the remote control.
Close the cover by sliding it back until it clicks into place.
3
UU
CC
CC
oo
oo
ssiiii
UU
oo
nnttttrrrr
oo
nn
nntttt
nn
ss
nn
nn
oollll
oo
hh
hh
ggtttt
gg
ee
ee
hh
hh
PP
PP
UU
UU
ee
ee
aa
nn
aa
nn
nniiiitttt
nn
eellll
ee
.
p
m
e
T
e
d
n
o
a
F
M
/
y
Dr
/
l
o
Co
g
n
i
w
S
r
e
w
r
o
e
v
P
Sa
E.
d
e
e
p
S
p
n
a
e
F
e
l
S
r
me
i
T
This chapter indicates how to operate and program
your air conditioner with the control panel on the unit.
E-
8
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the Fan speed.
Press the (On/Off) button.
1
Result:
If the temperature is not displayed on the control panel:
2
Press the button on the unit one or more times until the
temperature is displayed.
Result:
The air conditioner starts up in the cool mode.
The unit beeps twice.
The air conditioner is fitted with a protection mechanism to prevent
the unit from being damaged when it is started immediately after
being:
Plugged in
Stopped
It will start up normally after three minutes.
Mode
Cool/Dry/Fan
Mode
The unit beeps each time you press the button.
Cool/Dry/Fan
The air conditioner starts up in the Cool mode.
You can chang modes at any time.
Control Panel
Power
To adjust the temperature, press the or buttons on the unit one
3
or more times until the desired temperature is displayed.
The temperature can be set between 64 Fand 86 F.
Result:
Each time you press the or buttons:
- The temperature is adjusted by 1 F and displayed on
the control panel
- The unit beeps
The air conditioner starts cooling, if the room temperature is
higher than the selected temperature.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
To set the fan speed:
4
Press the button on the unit one or more times until the
Fan Speed
desired the Fan speed(F1, F2 or F3) is displayed.
Low
Medium
High
To control the direction of the air flow, refer to page 24.
5
E-
9
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.