SAMSUNG AV-R700 User Manual

ELECTRONICS

Instruction Manual

Digital Surround

AV Receiver System

AV-R700

AH68-01597B

21

Safety Warnings Precautions

Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the
ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other
equipment which may become hot. Before moving the player, ensure the disc tray is empty. This player is designed for
continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electrical supply. In order to
disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused
for a long period of time.

Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable from
the AC supply if the player malfunctions. Your player is not
intended for industrial use.

Use of this product is for personal use only.
Condensation may occur if your player or disc have been

stored in cold temperatures.
If transporting the player during the winter, wait approximately 2

hours until the unit has reached room temperature before using.

During thunderstorms, disconnect AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.

Do not expose the unit to direct sunlight or other heat
sources.

This could lead to overheating and malfunction of the
unit.

The battery used with this product contain chemicals

that are harmful to the environment.

Do not dispose of batteries in the general household

trash.

This symbol indicates that dangerous voltage which
can cause electric shock is present inside this unit.

This symbol alerts you to important operating and
maintenance instructions accompanying the unit.

WARNING: To reduce the risk of fire or electric shock, do not

expose this appliance to rain or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.

Wiring the Main Power Supply Plug(UK Only)

IMPORTANT NOTICE

The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin
face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same
colour as the fuse fitted in the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should
obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the
plug to a main socket as there is a risk of shock hazard from the bared flexible cord.

Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the main lead are coloured in accordance with the following code:–

BLUE = NEUTRAL BROWN = LIVE

As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH

THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN
AND YELLOW.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE REAR COVER. NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified
as a CLASS 1 LASER product.

CAUTION

PREP ARATION

√√

Let's find out difference between general amplifier and AV receiver!

General Amplifier

2 channels (left speaker and right speaker)

Play back music mainly

No decoder

Not play back various kinds of sound formats

AV Receiver

Multiple Channel (5.1 channel by default)

Play back music and video sound realistically

Has decoder

Dolby Pro Logic ll x

Dolby Pro Logic ll x is a new type of multiple
channel audio signal decoding method that
improves upon existing Dolby Pro Logic.

DTS (Digital Theater Systems)

DTS play backs 5.1 channel sound of wide-range
by playing sound of DVD and CD disk as surround
sound system.

DTS 96/24

DTS is the surround format implementing 5.1
channel multi channel sounds of 96KHz/24bit
without losing the image quality of DVD. In addition,
it can reproduce the matrix 6.1 of DTS 96/24
decoder signal.

DTS-ES

DTS-ES is the surround format implementing
surround type of discrete 6.1 channel while
preserving upper compatibility in response to
existing DTS Digital Sound format.
It is the latest digital sound format maximizing the
space quality and 360 surround experience by
adding rear center channels.

DOLBY DIGITAL EX

It not only significantly enhances space expression
capability of surround channel but also easily
implements the sound localization at the rear
according to sound field reproduction at 6.1 channel
including rear center channel.

DTS

It reproduces the digital PCM or analog stereo
sound source in 6.1 channels using the high
precision digital matrix of DTS only.

It refers to home theater exclusive amplifier by amplifying the audio signal from DVD and CD player as a core element of
home theater.

√√

What is AV receiver?

Features Contents

43

Play back various kinds of sound formats including Dolby
Digital and DTS
Many input/output connectors
No noise using digital signal type

PREPARATION

Safety Warnings ..............................................................................................................1

Precautions......................................................................................................................2

Features ..........................................................................................................................3

Contents ..........................................................................................................................4

Description ......................................................................................................................5

CONNECTIONS

Connecting the Speakers ...............................................................................................9

Connecting External Components ..................................................................................11

Connecting External Component.....................................................................................13

Connecting the FM Antenna............................................................................................14

OPERATION

Before Using AV Receivera.............................................................................................15

Selecting External Component Input ...............................................................................16

Setting the Speakera .......................................................................................................17

Setting DRC (Dynamic Range Compression) .................................................................21

Test Tone ........................................................................................................................22

Setting Speaker Level .....................................................................................................25

Dolby Pro Logic ll x Mode................................................................................................27

Dolby Pro Logic ll x Effect................................................................................................29

NEO:6 Mode....................................................................................................................31

SFE Mode........................................................................................................................33

EX/ES Mode ....................................................................................................................35

Stereo Mode ....................................................................................................................37

RADIO OPERATION

Listening to Radio ...........................................................................................................39

Presetting Radio Stations ...............................................................................................40

About RDS Broadcating ..................................................................................................41

MISCELLANEOUS

Convenient Functions .....................................................................................................43

Operating TV with Remote Control..................................................................................45

Operating VCR (DVD) with Remote Control....................................................................47

Before Calling for Service................................................................................................49

Specifications ..................................................................................................................51

Memo...............................................................................................................................52

This product is manufactured with technical cooperation with Digital
Theater Systems, Inc., is the registered trademark of Digital
Theater Systems.
(c)1996 Digital Theater Systems, Inc. All rights Reserved.

Manufactured under license from Dolby Laboratories.

“Dolby”, “ProLogic” and double-D symbol are the trademark of Dolby Laboratories.
Confidential unpublished works
(c)1992-1997 Dolby Laboratories. All rights are Reserved.

PREP ARATION

Description

[

Front Panel

]

[

Display

]

POWER button EXTERNAL VIDEO

INPUT CONNECTOR

VOLUME CONTROL

REMOTE CONTROL Sensor EXTERNAL OPTICAL DIGITAL

AUDIO INPUT CONNECTOR

SELECTION button

TUNING ( ) button

POWER STANDBY Indicator

EXTERNAL AUDIO INPUT CONNECTOR

SURROUND button

HEADPHONE Jack INPUT button

65

S.W

SPEAKER INDICATOR

SUBWOOFER

LEVEL INDICATOR

DOLBY PRO LOGIC

IIX

INDICATOR

VARIOUS

FUNCTION

INDICATOR

RADIO BROADCASTING
RECEIVING INDICATOR

RADIO STEREO INDICATOR

ANALOG INDICATOR

RADIO FREQUENCY
INDICATOR

OPTICAL DIGITAL
INDICATOR

DTS ES 96/24

INDICATOR

LIVE SURROUND

INDICATOR

L.PCM INDICATOR

NEO:6

INDICATOR

DOLBY DIGITAL EX

INDICATOR

MPEG2

INDICATOR

COAXIAL DIGITAL INDICATOR

DVD VIDEO INPUT

CONNECTOR

COOLING PAN

SAT VIDEO INPUT

CONNECTOR

5.1 CH ANALOG

AUDIO CONNECTOR

VCR VIDEO INPUT CONNECTOR

AM ANTENNA

CONNECTOR

VCR VIDEO OUTPUT CONNECTOR

MONITOR VIDEO OUTPUT

CONNECTOR

FM ANTENNA
CONNECTOR

OPTICAL DIGITAL AUDIO OUTPUT
CONNECTOR

DVD OPTICAL DIGITAL AUDIO INPUT CONNECTOR

SAT OPTICAL DIGITAL AUDIO
INPUT CONNECTOR

CD COAXIAL DIGITAL
AUDIO INPUT
CONNECTOR

SAT S-VIDEO INPUT CONNECTOR

VCR S-VIDEO INPUT CONNECTOR

VCR S-VIDEO OUTPUT CONNECTOR

CENTER SPEAKER TERMINAL

FRONT SPEAKER TERMINAL

REAR SPEAKER TERMINAL

MONITOR S-VIDEO OUTPUT CONNECTOR

[

Rear Panel

]

Accessories

√√

œœ

CD AUDIO INPUT CONNECTOR

DVD AUDIO INPUT CONNECTOR

SAT AUDIO INPUT CONNECTOR

Remote Control

FM Antenna User’s Manual

Battery(AAA Size 1.5V) AM Antenna

VCR AUDIO INPUT CONNECTOR

VCR AUDIO OUTPUT CONNECTOR
SUBWOOFER OUTPUT CONNECTOR 1

SUBWOOFER OUTPUT CONNECTOR 2

,

DVD S-VIDEO

INPUT

CONNECTOR

PREP ARATION

USER’S GUIDE

Description

VOLUME CONTROL button

MUTE button

MENU button

ANALOG/DIGITAL button

POWER button

SLEEP button

TUNER button

NEO : 6 button

EXTERNAL DEVICE PLAYBACK button

DISPLAY button

MODE button

Direct Function Select button

TV Indicator
VCR Indicator
AV RECEIVER Indicator

TV/VIDEO

,

FUNCTION button

DVD Indicator
MODE button
MO/ST button

SUBWOOFER button
SFE MODE button

EX/ES button

EFFECT button

STEREO button

MOVE/SELECT button

TUNER MEMORY button
TUNING/CHANNEL button

SPEAKER LEVEL button

TEST TONE button

SPEAKER SETUP button

SPEAKER DISTANCE button

RDS Selection button

[

Remote Control

]

87

To open the remote control cover,
push the top of the cover, then slide
downward.

Insert Remote Batteries

The remote control can be used up to approximately 23
feet/7 meters in a straight line. It can also be operated at
a horizontal angle of up to 30° from the remote control
sensor.

Range of Operation of the Remote Control

Remove the battery
cover on the back of
the remote by
pressing down and
sliding the cover in
the direction of the
arrow.

1

Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).

2

Replace the battery
cover.

3

Follow these precautions to avoid leaking or cracking batteries:

•

Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).

•

Use the correct type of batteries.Batteries that look similar may differ in voltage.

•

Always replace both batteries at the same time.

•

Do not expose batteries to heat or flame.

Caution !

PREP ARATION

Number(0~9) buttons

Connecting the Speakers

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

•

Place the rear left and right speaker at the interval of front
left and right speaker.

•

If there isn't enough now, place rear speakers to face
down other.

•

Place the rear speakers about 70 cm to 1 m above your
ear, facing slightly downwards.

❈ Unlike the front and center speakers, the rear speakers

and used to mainly sound effects and sound will not
come from them all the time.

Rear Speakers

•

If you place 1 rear center speaker, place it so that it faces
forward from the back of listener.

•

Place the rear center speaker about 70 cm to 1 m above
rear speakers, facing slightly downwards.

Rear Center Speaker

SL SR

SB

•

Adjust the angle of front left and right speakers so
that it can form 30 degree to the left and right from
the listening position.

•

Place the speakers so that their tweeters will be at
the same height as your ear.

•

Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speaker.

Front Speakers

•

It is best to install center speaker at the same height as
the front speakers.

•

You can also place center speaker directly over or
under the TV.

Center Speaker

•

Place AV Receiver on the dedicated stand or chest of
living room or under the TV stand properly.

Position of AV Receiver

•

The position of the subwoofer is not so critical. Place it
anywhere you like.

•

Usually, it is placed by a corner near the front speakers.

Subwoofer

When you place the speaker on the wall, make sure
to fasten it tightly so that it may not fall off.

109

Caution!

CONNECTIONS

•

Never touch speaker terminals while
the power is on. Doing so could
result in electric shock.

•

Make sure the polarities (+ and -)
are correctly.

1

√ Connecting Front Speaker Wire

√ Connecting Center/Rear Speaker Wire

PASSIVE

SUBWOOFER

ACTIVE SUBWOOFER

(BUILT-IN POWER

AMPLIFIER)

POWER

AMPLIFIER

FRONT (R)

FRONT (L)

REAR (R)

REAR (L)

MAIN UNIT
AV-R700

CENTER REAR CENTER

Caution!

Turn and loosen the
speaker connector.

2

1

Press the tab of the
speaker connector.

2

Insert the black wire into the black(-)
terminal and the red wire into the
red(+) terminal.

3

Turn and fasten the
speaker connector.

Insert the black wire into the black(-)
terminal and the red wire into the
red(+) terminal.

Connecting External Components

DVD Player

Video Projector

SA T Player

Video Player

TV MD Player

•

Disconnect the power plug from the outlet if you do not use this unit for long period of time.

•

If the Audio Output connector of external
component is only 1, connect Audio Output
connector or external component to either of
Audio Input connector (right or left) of main unit.

•

Connect the red cable of audio cable to red
connector and white cable to white connector.

•

When you connect Video Input connector of
external component to Video Output connector
of main unit, connect Video Input connector of
external component either to Video Output
connector or S-Video Output connector.

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting Video Component

1211

Caution!

CONNECTIONS

DIGITAL

OUT

AUDIO

AUDIO

OUT

OUT

LR

LRLR

AUDIO

IN

VIDEO

S-VIDEO

OUT

OUT

VIDEO

OUT IN

S-VIDEO

S-VIDEO

OUT IN

DIGITAL

AUDIO

VIDEO

OUT

DIGITAL

IN

OUT

LR

IN

OUT

S-VIDEO

OUT

VIDEOINS-VIDEO

IN

Connecting External Component

LR

DIGITAL

OUT

AUDIO

OUT

FRONT SURR.

SUB

WOOFER

L

R

L

R

CENTER

CD Player

DVD or 5.1 Channel Player

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting Audio Component/ 5.1 Channel

1413

1. Connect the FM antenna supplied to the FM

75ΩCOAXIAL terminal as a temporary mea-sure.

2. Slowly move the antenna wire around until you find
a location where reception is good, then fasten it to
a wall or other rigid surface.

1. Connect the AM loop antenna supplied to the AM
and terminals.

2. If reception is poor, connect an outdoor single vinyl-

covered wire to the AM ter-minal. (Keep the AM loop
antenna con-nected).

The cooling fan dissipates the heat generated inside the unit so that the unit can
be operated normally. The cooling fan is activated automatically to supply cool air
to the unit.

Please observe the following cautions for your safety.

•

Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the
unit could rise and may damage it.

•

Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are
covered with a newspaper or cloth, heat may build up inside the unit and fire may result.)

Connecting the FM and AM Antennas

FM antenna connection

If AM reception is poor, connect an
outdoor AM antenna(not supplied).

FM Antenna (supplied)

AM Loop Antenna
(supplied)

Snap the tabs on the loop into the
slots of the base to assemble the
AM loop antenna.

COOLING FAN

AM antenna connection

CONNECTIONS

Before Using AV Receiver

Turning On/Off

Functions of Dedicated Remote Control

Connect the power plug to the outlet.

1

Press the POWER ( ) button of the main unit.

•

This unit will be turned on or off.

2

MAIN UNIT

REMOTE CONTROL

Press MODE button.

•

Each time you press this button, it will select and blink TV indicator ➝ VCR indicator
➝DVD indicator ➝ AV Receiver indicator in turn.

•

You can operate TV after TV indicator blinking.
You can operate VCR after VCR indicator blinking.
You can operate DVD after DVD indicator blinking.
You can operate AV Receiver after AV Receiver indicator blinking.

•

This unit will not turned on or off even if you press the POWER ( ) button of
remote controller while main unit is turned off.

•

When you turn off the power by pressing the POWER ( ) button of remote
control, this unit will be standby mode.To completely turn off the power, press the
POWER ( ) button of the main unit. Standby indicator will be turned off.

•

Basic operation of remote control is set up based on Samsung products.
Refer to page 45~48 for more details on operation method.

You can operate TV, VCR, DVD, AV Receiver with one remote control.

You can listen ti sound in Analog 2 Channels or Dolby Digital 5.1 Channel using this unit.







1615

Press the FUNCTION button.

•

When you select the audio external component (external component without
Video Output connector), the image of video external component (external
component with Video Output connector) used last will appear in the TV screen.

•

You can watch the image of video external component while listening to sound of
audio external component.

Selecting External Component Input

•

You can enjoy Dolby Digital effect only if you connect Audio Output connector of
external audio component to optical/coaxial digital Audio Input connector of main unit.

To set the menu function of external component

Press the MENU button.

•

Menu setup screen of TV, VCR and DVD Player will appear.

REMOTE CONTROL

To Select the Function

To Select Analog/Digital Input

REMOTE CONTROL

•

You can directly select 5.1CH, VCR, DVD, CD, SAT, or AUX.

•

For DVD, SAT, AUX Function
ANALOG and OPTICAL (1, 2, 3) will be selected repetitively.

•

For CD Function

ANALOG and COAXIAL will be selected repetitively.

MAIN UNIT

REMOTE CONTROL

Press INPUT button.

•

Each time you press the this button, 5.1CH MULTI CH ➝ CD ➝ DVD ➝SAT ➝ VCR ➝ AUX
➝FM ➝ AM will be selected in turn.

Press the ANALOG/DIGIT AL button.

•

You can operate this function only with remote controller.

•

This function will be selected in analogue only for VCR function, and will not work for 5.1CH MULTI CH function.

Caution!

Press the POWER ( ) button of the remote control while main unit is turned on.

•

This unit will be turned on or off.

Method 1

Press DIRECT FUNCTION Select button.

Method 2

Press the FUNCTION button.

•

Each time you press the this button, 5.1CH MULTI CH ➝ CD ➝ DVD ➝SAT ➝ VCR ➝
AUX ➝FM ➝ AM will be selected in turn.

OPERA TION

Setting the Speaker

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.Signal outputs
and frequency response from the speaker will automatically be adjusted according to your speaker configuration
and whether certain speakers are used or not.

Press SPK SEL. button to select the speaker you want.

•

Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝SB SPK ➝
SW SPK ➝CROVR ➝ SPK MODE OFF will be selected in turn.

Press …† button to set the speaker as you want.

Repeat the steps 1 and 2 to set the speaker.

To Exit Setup Mode

•

Wait for about 5 seconds or press the SPK SEL. button of the remote control to
select SPK MODE OFF.

To Use SUBWOOFER button of Remote Control

Press SUBWOOFER button.

•

Each time you press this button, SW SPK : YES, SW SPK : NO will be selected in turn.

•

If you play in 2 Channel Stereo, select 'YES' to use Subwoofer and 'NO' not to use.

√

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button one time.

•

“SPEAKER SETUP” appears in the display.

Press SURROUND button to select the speaker you want.

Each time you press this button, F.SPK ➝ C.SPK ➝S.SPK ➝ SB

SPK ➝SW SPK ➝CROVR will be selected in turn.
Press SELECT ( ) button to set the speaker as you want.

Repeat the steps 3 and 4 to set the speaker.

To Exit Setup Mode

•

Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit.
“SETUP MODE OFF” appears on the display and exits Setup Mode.

•

LARGE : Select when you use large speaker. You can listen to full

ranges of sound from bass to treble.

•

SMALL : Select this when you use small speaker. Bass below

100ß‘ will not be output from the whole speakers but only
from subwoofer.

•

NONE : Select this when you use no speaker.

•

YES : Select this when you use Subwoofer Speaker if you play

back in 2 Channel Stereo.

•

NO : Select when you do not use Subwoofer Speaker if you play

back in 2 Channel Stereo.

•

CROVR: Select the crossover frequency depending on the size of

speaker connected when you use subwoofer. Select 40Hz
if cone paper speaker is 16cm, select 60Hz for 14cm,
80Hz for 12cm, 100Hz for 10cm, 12Hz for 8cm ,150Hz for
6cm and 200Hz for 4cm.

•

If F.SPK is set to ‘SMALL’, SW SPK is fixed to ‘YES’.

•

If S.SPK is set to ‘NONE’, SB SPK is fixed to ‘NONE’.

•

You cannot use Speaker Setup Mode in 5.1CH MULTI CH function.

1817

•

F.SPK (Front) : LARGE, SMALL

•

C.SPK (Center) : LARGE, SMALL, NONE

•

S.SPK (Rear) : LARGE, SMALL, NONE

•

SB SPK (Rear Center) : LARGE, SMALL, NONE

•

SW SPK (Subwoofer) : YES, NO

•

CROVR (Crossover Frequency): 40, 60, 80, 100, 120, 150,200Hz

Setting the Speaker

1

2
3

REMOTE CONTROL

Caution!

MAIN UNIT

1

2

4

5

3

,

OPERA TION

Setting the Speaker

Press the SPEAKER DIST ANCE button to select the

speaker you want.

•

Each time you press this button, F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B ➝ S.L ➝
S.W ➝DISTANCE OFF will be selected in turn.

Press …† button to set the speaker distance.

•

For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to
listening position between 0.0~1.5m at the interval of 0.3m.

•

For S. R, S.B, S.L Speaker, you can set the distance from the speaker to
listening position between 0.0~4.5m at the interval of 0.3m.

Repeat the steps 1 and 2 to set the speaker distance.

Set the distance from the speaker to listening position at the interval of 0.3m.

•

F.L (Front-Left) : 0ft 0.0m ~ 5ft 1.5m

•

CEN (Center) : 0ft 0.0m ~ 5ft 1.5m

•

F.R (Front-Right) : 0ft 0.0m ~ 5ft 1.5m

•

S.R (Rear-Right) : 0ft 0.0m ~ 15ft 4.5m

•

S.B (Rear Center): 0ft 0.0m ~ 15ft 4.5m

•

S.L (Rear-Left): 0ft 0.0m ~ 15ft 4.5m

To Exit Setup Mode

•

Wait for about 5 seconds or press the SPEAKER DISTANCE button of remote control
to select DISTANCE OFF.

2019

√

Press and hold SURROUND button for about 5 seconds

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 2 times.

•

“DISTANCE SETUP” appears on the display.

Press SURROUND button to select the speaker you want.

•

Each time you press this button, F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B ➝ S.L ➝ S.W
will be selected in turn.

Press SELECT( ) button to set the speaker distance.

•

For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to
listening position between 0.0~1.5m at the interval of 0.3m.

•

For S.R, S.B, S.L Speaker, you can set the distance from the speaker to listening
position between 0.0~4.5m at the interval of 0.3m.

Repeat the steps 3 and 4 to set the speaker distance.

Setting Speaker Distance

To Exit Setup Mode

•

Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. “SETUP MODE
OFF” appears on the display and exit Setup Mode.

•

If the listening position is beyond the range of speaker
distance setup when you place the speaker, set the
speaker distance to the maximum.

REMOTE CONTROL

1

2

3

MAIN UNIT

1
2

4

5

3

,

OPERA TION

Setting DRC

(Dynamic Range Compression)

You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.

2221

Test Tone

Use test tine to check speaker connection status or defect of speaker or adjust the level.

Press TEST TONE button.

•

Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝S.R
➝S.B ➝ S.L ➝ S.W.

•

During test tone output, press …† button to adjust the speaker output level
from -10 to +10 dB by 1 step.

To Stop Test Tone

•

Press TEST TONE button again.

√

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 3 times.

•

“DRC SETUP” appears on the display.

Press SURROUND button to set DRC.

•

Each time you press this
button, DRC : STD ➝ DRC :
MIN ➝DRC : MAX will be

selected in turn.

To Exit Setup Mode

•

Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit.
“SETUP MODE OFF” appears on the display and exits Setup Mode.

√

•

You cannot use test tone in 5.1CH MULTI CH function.

•

This function operates only in main unit.

•

STD : Set DRC effect to standard.

•

MAX : Set DRC effect to maximum.

•

MIN : Set DRC effect to minimum.

Setting DRC

MAIN UNIT

1
2

3

Caution!

To Automatically Output Test Tone

REMOTE CONTROL

1

Caution!

OPERA TION

•

F.L (Front-Left) : -10 ~ +10dB

•

CEN (Center) : -10 ~ +10dB

•

F.R (Front-Right) : -10 ~ +10dB

•

S.R (Rear-Right) : -10 ~ +10dB

•

S.B (Rear Center): -10 ~ +10dB

•

S.L (Rear-Left): -10 ~ +10dB

•

S.W (Subwoofer): -10 ~ +10dB

2423

Test Tone

Use test tone to check speaker connection status or defect of speaker or adjust the level.

Test Tone Output

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 5 times.

•

“TEST-T MANU” appears in the display.

Press SURROUND button.

•

Each time you press this button, F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B ➝ S.L ➝S.W

will be selected in turn.

Press SELECT( )button to set the test tone as you want.

•

You can adjust the speaker output level from -10 to +10dB by 1 step.

√

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 4 times.

•

“TEST-T AUTO” appears in the display.

Press SURROUND button.

•

Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B
➝S.L ➝ S.W .

•

During test signal output, press SELECT ( ) button to adjust the speaker output
level from -10 to +10 dB by 1 step.

√

•

You cannot use test tone in 5.1CH MULTI CH function.

To Automatically Output Test Tone To Manually Output Test Tone

MAIN UNIT

1
2

3

MAIN UNIT

1
2

4

3

To Stop Test Tone

Method 1) Press INPUT button 2 times.

•

“TEST-T OFF” appears on the display and test tone stops.

Method 2) Turn VOLUME CONTROL.

•

“SETUP MODE OFF” appears on the display and test tone stops.

To Stop Test Tone

Method 1) Press INPUT button 1 time.

•

“TEST-T OFF” appears on the display and test signal stops.

Method 2) Turn VOLUME CONTROL.

•

“SETUP MODE OFF” appears on the display and test tone stops.

Caution!

,

,

OPERA TION

Setting Speaker Level

You can set the balance and level of speakers

Press SPK LEVEL button to select the speaker you want.

•

Each time you press this button, F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B ➝ S.L ➝ S.W ➝
SPK LEVEL OFF will be selected in turn.

Press …† button to set the speaker level you want.

•

You can adjust it from -10 to +10dB by 1 step.
The sound gets smaller at -10dB and louder at +10dB.
Default setting value is 00dB.

Repeat the steps 1 and 2 to set it.

•

F.L (Front-Left) : -10 ~ +10dB

•

CEN (Center) : -10 ~ +10dB

•

F.R (Front-Right) : -10 ~ +10dB

•

S.R (Rear-Right) : -10 ~ +10dB

•

S.B (Rear Center): -10 ~ +10dB

•

S.L (Rear-Left): -10 ~ +10dB

•

S.W (Subwoofer): -10 ~ +10dB

To Exit Setup Mode

•

Wait for about 5 seconds or press SPK LEVEL button of remote control to select SPK
LEVEL OFF.

To Exit Setup Mode

•

Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP
MODE OFF” appears on the display and exits Setup Menu.

2625

√

Press and hold SURROUND for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 7 times.

•

“LEVEL SETUP” appears on the display.

Press SURROUND button.

•

Each time you press this button, F.L ➝ CEN ➝ F.R ➝S.R ➝ S.B ➝ S.L ➝ S.W

will be selected in turn.

Press SELECT( ) button to set to the speaker level you

want.

•

You can adjust it from -10 to +10dB by 1 step.

•

The sound gets smaller at -10dB and louder at +10dB.

•

Default setting value is 00dB

Repeat the steps 3 and 4 to set it.

Setting Speaker Level

Remote Control

Remote Control

1

2

3

1

2

4

5

3

,

OPERA TION

Dolby Pro Logic llx Mode

You can experience surround sound regardless of type of stereo mix by making existing Dolby Surround mix
sound similar to discrete 5.1 Channel Surround.

Press MODE button.

•

Each time you press this button, MUSIC ➝ CINEMA ➝ MATRIX ➝ GAME ➝

PROLOGIC will be selected in turn.

•

MUSIC : Provide 5.1 Channel Surround sound to digital, analog
or existing stereo source such as CD, TAPE, FM, TV and Stereo
VC.

•

CINEMA : Provide 5.1 Channel Surround sound to sound track of
stereo movie encoded as Dolby Surround.

•

MATRIX : You can feel 5.1 Channel Surround sound enjoying the
space of sound.

•

GAME : When you play game, you can enjoy game with sound
effect as if you are at actual site.

•

PROLOGIC : Decode(3/1 Surround) the sound track of stereo
music encoded as Dolby Surround to Dolby Pro Logic.

2827

Press SURROUND button briefly to select “DPL llx” Mode.

•

Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝STEREO will be
selected in turn.

Press SELECT( ) button.

•

Each time you press SELECT ( ) button, MUSIC ➝ CINEMA ➝MATRIX ➝
GAME ➝PROLOGIC will be selected in turn.

•

Each time you press SELECT ( ) button, PROLOGIC ➝ GAME ➝MATRIX
➝CINEMA ➝ MUSIC will be selected in turn.

Dolby Pro Logic ll x Mode

•

You cannot use Dolby Pro Logic ll x Mode for multi channel
signal encoded as Dolby Digital and DTS.

•

You cannot use Dolby Pro Logic ll x Mode in 5.1 multi­channel function.

•

Pro Logic works only for PCM audio signals with sampling
frequency of 32KHz, 44KHz or 48KHz.

•

Sound will not be output from rear center speaker if PCM
audio signal is not stereo but mono.

•

Sound will be output from some speaker only if you
connect the external component only to Audio Input
connector (or R) of the main unit.

To Exit Setup Mode

•

Wait for about 5 seconds.

To Exit Setup Mode

•

Wait for about 5 seconds.

REMOTE CONTROL

1

MAIN UNIT

Caution!

1

2

,

OPERA TION

Dolby Pro Logic llx Effect

This function works only in Dolby PRO LOGIC IIX MUSIC Mode.

Press MODE button to select ‘MUSIC’ Mode.
Press EFFECT button.

•

Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA will be

selected in turn.

Press …† button to select Dolby Pro Logic IIx effect you want.

•

C-WIDTH: You can set from 0 to 7.

•

DIMENSION: You can set from 0 to 7.

•

PANORAMA: You can Set it ON or OFF.

Repeat the steps 2 and 3 to set the Dolby Pro Logic IIx effect.

•

C-WIDTH : Sound will be output from center speaker only. Front-left
and front-right speaker give sound field effect only. In addition, sounds
are output in different volumes from Front-Left, Front-Right Speaker and
Center Speaker.

•

DIMENSION : Adjust the sound balance if the sound is unbalanced to
front or rear speaker.

•

PANORAMA : Give the effect expanding and covering the sound from
front-left and front-right Speaker to both walls.

To Exit Setup Mode

•

Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP
MODE OFF” appears on the display and exits Setup Mode.

3029

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.Press

INPUT button 8 times.

•

“DPL ll x MODE”appears on the display.

Press SURROUND button.

•

Each time you press this button, DIMENSION ➝ PANORAMA ➝ C-WIDTH will
be selected in turn.

Press SELECT( ) button to select Dolby Pro Logic llx

effect you want.

Repeat the steps 3 and 4 to set Dolby Pro Logic llx effect.

Dolby Pro Logic llx Effect

To Exit Setup Mode

•

Wait for about 5 seconds .

REMOTE CONTROL

1
2

4

3

MAIN UNIT

1

2

4

5

3

,

OPERA TION

NEO:6 Mode

You can play back 2 channel sound in 6.1 channel of 360 degree surround when enjoying music or movie.

Press NEO:6 MODE button.

•

Each time you press this button, MUSIC ➝ CINEMA will be selected in turn.

3231

Press SURROUND button briefly to select “NEO:6” Mode.

•

Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝STEREO will be
selected in turn.

Press SELECT( ) button.

•

Each time you press this button, MUSIC ➝ CINEMA will be selected in turn.

This mode decodes 2 channel signals to high precision digital matrix
decoder.
DTS NEO:6 decoder discretes 2 channel sound to Discrete 6.1
channel sound.

•

MUSIC : NEO:6 MUSIC Mode is used as optimized to music
according to played signal.

•

CINEMA : NEO:6 CINEMA Mode is used as optimized to movie
according to played signal.

NEO : 6 Mode

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 9 times.

•

“NEO:6 MODE” appears on the display.

Press SURROUND button.

•

“CEN-IMG” appears on the display.

Press SELECT( ) button to set the sound image you want.

•

You can set the sound image from 0 to 5.

•

NEO:6 Mode can be used in multi channel signal
encoded to Dolby Digital or DTS.

•

Pro Logic works only for PCM audio signals with sampling
frequency of 32KHz, 44KHz or 48KHz..

•

You can use this function to set the sound image of Center
Speaker only in the main unit.

To Exit Setup Mode

•

Wait for about 5 seconds.

To Exit Setup Mode

•

Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP MODE OFF’ appears
on the display and exits Setup Mode.

If TV (or screen) is installed high, you can feel the balance of sound and image by
raising the sound image of Center Speaker.

REMOTE CONTROL

1

Caution!

MAIN UNIT

1

1
2

3
4

2

To Set Sound Image of Center Speaker

Caution!

,

,

OPERA TION

SFE Mode

Refer to the unique sound existing at specific place and you can feel live sound as if you are listening at
actual site.

Press SEF MODE button.

•

Each time you press this button, LIVE ➝ ROCK ➝ CLASSIC ➝JAZZ ➝ MIDNIGHT

➝HALL ➝ CINEMA ➝ CHURCH will be selected in turn.

3433

Press SURROUND button briefly to select ‘SFE’ Mode. Each

time you press this button, DPL II x ➝ NEO:6 ➝ SFE ➝STEREO will be
selected in turn.

Press SELECT( ) button.

•

Each time you press Select ( ) button, LIVE ➝ ROCK ➝ CLASSIC ➝JAZZ
➝MIDNIGHT ➝ HALL ➝ CINEMA ➝CHURCH will be selected in turn

•

Each time you press Select ( ) button, CHURCH ➝ CINEMA ➝ HALL ➝
MIDNIGHT ➝JAZZ ➝ CLASSIC ➝ ROCK ➝LIVE will be selected in turn.

•

LIVE, ROCK, CLASSIC, JAZZ : Select the genre suitable for the
music among Live, Rock, Classic and Jazz to listen to music.

•

MIDNIGHT : Emphasize bass when you listen to music at midnight.

•

HALL : Clear music as if you are listening at concert hall.

•

CINEMA : Enjoy sound as if you are in cinema.

•

CHURCH : Enjoy magnificent sound as if you are listening at
church.

SFE Mode

To Exit Setup Mode

•

Wait for about 5 seconds.

To Exit Setup Mode

•

Wait for about 5 seconds.

REMOTE CONTROL

1

MAIN UNIT

1

2

,

OPERA TION

EX/ES Mode

This mode enable you to listen 6.1 channel surround to the source encoded to Dolby Digital-EX, DTS-ES such as DVD.
This function works when Dolby Digital 5.1 channel source is inputted, and does not work when LPCM and Dolby Digital
2 channel source are entered.

Press EX/ES button.

•

Each time you press this button, EX/ES AUTO ➝ EX/ES ON ➝ EX/ES OFF

will be selected in turn.

3635

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button 10 times.

•

“EX/ES SETUP” appears on the display.

Press SURROUND button.

•

Each time you press this button, EX/ES : AUTO ➝ EX/ES : ON ➝ EX/ES :
OFF will be selected in turn.

•

AUTO : 7.1 channel(or 6.1 channel) sound will be played back to

7.1 channel(or 6.1 channel) and 5.1 channel sound will be
automatically converted to and output as 5.1 channel.

•

ON : 5.1 channel sound will be converted to and output as 7.1

channel (or 6.1 channel).

•

OFF : 7.1 channel (or 6.1 channel) sound will be converted to and

output as 5.1 channel.

EX/ES Mode

Movie sound track encoded with Dolby Digital EX can play back
the rear center channel added during program mixing. Rear
center channel provides fine image, in-depth and realistic
feeling.

Dolby Digital - EX

•

You cannot use Dolby Digital-EX in the system without rear
center speaker.

•

You need to set it to EX/ES Mode when playing back disk
encoded to Dolby Digital-EX in 6.1 channel.

•

Some disks encoded with Dolby Digital-EX do not contain
identification signal. In this case, set EX/ES to ON.

Rear center channel is added to DTS 5.1 channel, improving the
sense of direction and space for sound. Since DTS-ES decoder
is built-in in the main unit, you can play back the disk encoded
with DTS-ES Discrete and DTS-ES Matrix. DTS-ES Discrete 6.1
can record the sound of all channels including rear center
channel digitally and play back the recorded sound as they are.

DTS-ES (Discrete 6.1, Matrix 6.1)

•

You cannot use DTS-ES in the system without rear center
speaker.

To Exit Setup Mode

•

Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP
MODE OFF’ appears on the display and exits Setup Mode.

To Exit Setup Mode

•

Wait for about 5 seconds or press EX/ES button of the remote control to select EX/ES
: OFF.

REMOTE CONTROL

MAIN UNIT

Caution!

Caution!

Method

1

2
3

OPERA TION

3837

Stereo Mode

You can select this mode when you listen to the sound at Front-Left speaker, Front-Right speaker and
subwoofer.

•

96KHz PCM is not played back in Stereo Mode.

•

When PCM and Analog Stereo signal are input,
left/right channel is played back in Stereo Mode.

L/R : Front Speaker (Left/Right) C : Center Speaker SL/SR : Rear Speaker (Left/Right) S : Rear Center Speaker SW : Subwoofer

For Surround Mode and Input Signal

•

2 channel Dolby Digital signal has Dolby Digital Pro Logic. Speaker Setup is set to LARGE, SMALL, or YES.

•

If there is no surround signal in DVD disk, sound will not output from rear-left speaker, rear-right speaker, center speaker, and
subwoofer.

Dolby D Surr. EX Dolby Digital 5.1

OOO-O

DIGITAL L, C, R, SL, SR, S, SW

Dolby D (5.1ch) Dolby Digital 5.1

OOO-O

DIGITAL L, C, R, SL, SR, SW

Dolby D (2ch) Pro Logic II x

OOO OO

DIGITAL L, R

Dolby D (2ch Surr) Pro Logic II x

OOO OO

DIGITAL L, R, S

L.PCM (Audio) Pro Logic II x

OOO OO

L.PCM L, R

Analog Pro Logic II x

OOO OO

ANALOG -

DTS-ES DTS 5.1

OOO OO

dts, ES

L, C, R, SL, SR, S, SW

DTS 96/24 DTS 96/24

OOO OO

DTS 96/24 L, C, R, SL, SR, SW

DTS (5.1) DTS 5.1

OOO -O

dts

L, C, R, SL, SR, SW

L.PCM (Audio) Neo:6

OOO O-

L.

PCM L, R

Analog Neo:6

OOO O-

ANALOG -

Dolby D (2ch) Neo:6

OOO O-

DIGITAL L, R

Dolby D (2ch Surr) Neo:6

OOO O-

DIGITAL L, R, S

Dolby Surr. EX SFE

-----

DIGITAL L, C, R, SL, SR, S, SW

Dolby D (5.1ch) SFE

-----

DIGITAL L, C, R, SL, SR, SW

Dolby D (2ch) SFE

OOO OO

DIGITAL L, R

Dolby D (2ch Surr) SFE

OOO OO

DIGITAL L, R, S

DTS-ES SFE

----- dts, ES

L, C, R, SL, SR, S, SW

DTS (5.1ch) SFE

----- dts

L, C, R, SL, SR, SW

L.PCM (Audio) SFE

OOO OO

L.PCM L, R

Analog SFE

OOO OO

ANALOG -

Dolby D Surr. EX Dolby Digital EX

OOO OO

DIGITAL L, C, R, SL, SR, S, SW

Dolby D (5.1ch) Dolby Digital EX

OOO OO

DIGITAL L, C, R, SL, SR, SW

DTS-ES DTS-ES

OOO OO

dts, ES

L, C, R, SL, SR, S, SW

DTS (5.1ch) DTS-ES

OOO OO

dts

L, C, R, SL, SR, SW

Dolby Surr. EX Stereo

O

-- -

O

DIGITAL L, C, R, SL, SR, S, SW

Dolby D (5.1ch) Stereo

O

-- -

O

DIGITAL L, C, R, SL, SR, SW

Dolby D (2ch) Stereo

O

-- -

-

DIGITAL L, R,

Dolby D (2ch Surr) Stereo

O

-- -

-

DIGITAL L, R, S

DTS-ES Stereo

O

-- -Odts, ES

L, C, R, SL, SR, S, SW

DTS 96/24 Stereo

O

-- -Odts

96/24 L, C, R, SL, SR, SW

DTS (5.1ch) Stereo

O

-- -Odts

L, C, R, SL, SR, SW

L.PCM (Audio) Stereo

O

-- -

-

L.PCM L, R

L.PCM 96KHz Stereo

O

-- -

-

L.PCM L, R

Analog Stereo

O

-- -

-

ANALOG -

Surround Mode Input Signal Decoding

Output Channel

L/R C

SL
SR

SB

SubW

Display Information

Display Signal Format Channel Status

EX/ES

DOLBY

(MUSIC,
CINEMA,
MATRIX,

GAME,

PROLOGIC

)

NEO:6

(MUSIC,
CINEMA)

STEREO

SFE

Press STEREO button.

•

“STEREO” appears in the

display and Stereo Mode is
selected.

Press SURROUND button briefly to select

‘STEREO’.

•

Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝
STEREO will be selected in turn.

To Exit Setup Mode

•

Wait for about 5 seconds.

To Exit Setup Mode

•

Wait for about 5 seconds.

REMOTE CONTROL MAIN UNIT

Caution!

Caution!

OPERA TION

Listening to Radio

You can listen to the chosen band (FM, AM broadcast stations) by using either the automatic or manual
tuning operation.

Presetting Radio Stations

You can preset to 30 stations including FM and AM broadcasting.

4039

Press TUNER button.

•

Each time you press this button, FM ➝ AM will be selected in turn.

Press Select button and then TUNING/CH( ) button to

select 89.1.

•

Refer to step 2, page 39, to tune in automatically and manually.

Press TUNER MEMORY button.

•

Tuner number will blink on the display.

Press TUNING/CH( ) button to select 2ch.

•

You can select from 1 to 30ch.

Press TUNER MEMORY button.

•

Tuner number will disappear and 89.1 station will be preset in 2ch.

To preset other stations, repeat the steps 2 to 5.

To Listen to Preset Station

•

Press Select button of the remote control to select the PRESET and press
TUNING/CH ( ) button.

Ex) If you preset FM 89.1 station in 2ch

Press TUNER button.

•

Each time you press this button, FM ➝ AM will be repetitively
selected.

Select frequency.

•

Automatic Tuning 1 :

1) Press ENTER button to select PRESET.

2) Press TUNING/CH( ) button to select the preset

frequency.

•

Automatic Tuning 2 :

1) Press ENTER button to select MANUAL

2) Press and hold TUNING/CH( ) button to

automatically tune in frequency.

•

Manual Tuning :

1) Press ENTER button to select MANUAL.

2) Press TUNING/CH( ) button briefly to increase or

decrease frequency by step by step.

Press INPUT button to select FM or

AM.

Select the frequency.

•

Automatic Tuning :
Press and hold TUNING/CH( ) button to

automatically tune in frequency.

•

Manual Tuning :
Press TUNING/CH( ) button briefly to

increase or decrease frequency by step by step.

To Listen to Mono/Stereo

Press MO/ST button.

•

Each time you press this button, STEREO, MONO will be selected in turn.

•

If you select MONO in the area with weak reception and blanket area, you can listen to clear broadcasting without noise.

•

This function works only in Remote Control.

REMOTE CONTROL MAIN UNIT

1

2

1

2

,,,,,

REMOTE CONTROL

1

2

4

5

6

3

,
,

,

RADIO OPERA TION

About RDS broadcasting

•

RDS is not available for AM broadcasts.

•

RDS may not operate correctly if the station tuned is not transmitting
RDS signal properly or if the signal strength is weak.

•

If searching finishes at once,“PS”,and “RT” will not appear on the display.

Using the RDS (Radio Data System) to receive FM stations

PTY (Program Type) indication and PTY-SEARCH function

What information can RDS signals provide?

RDS allows FM stations to send an additional signal along with their regular program signals. For
example,the stations send their station names,as well as information about what type of program they
broadcast, such as sports or music,etc.

When tuned to an FM station which provides the RDS service,the RDS indicator
lights up on the display.

•

Description on RDS function

1. PTY (Program Type) : Displays the type of programme currently being broadcast

2. PS NAME (Program Service Name) :

Indicates the name of broadcasting station

and is composed of 8 characters.

3. RT (Radio Text) :

Decodes the text broadcast by a station (if any) and is composed

of maximum 64 characters.

4. CT (Clock Time) :

Decodes the real time clock from the FM frequency.

• Some stations may not transmit PTY, RT or CT information therefore this may not be
displayed in all cases.

5. TA (Traffic Announcement) :

When this symbol flashes it shows that the traffic

announcement is in progress.

You can see the RDS signals the station sends on the display.

TO show the RDS signals

Press RDS DISPLAY while listening to an FM station.

Each time you press the button, the display change to show you the following information:

PS (Program Service) :While searching,"PS"appears and then the station names will be
displayed."NO PS" appears if no signal is sent.
RT(RadioText) : while searching,"RT"appears and then text messages the station sends
will be displayed. "NO RT"appears if no signal is sent.

Frequency : station frequency (non-RDS service)

About characters shown in the display

When the display shows PS,or RT signals,the following characters are used.

•

The display window cannot differentiate upper case and lower case lrtters and always
uses upper case letters.

•

The display window cannot show accented letters, “A,” for instance, may stans for
accented “A’s” like “À, Â, Ä, Á, Åand Ã.”

To search for a program using the PTY codes

Before you start, remember...

•

The PTY Search is only applicable to preset
stations.

•

To stop searching any time during the process,
press PTY SEARCH while searching.

•

There is a time limit in doing the following steps.
If the setting is cancelled before you finish, start
from step 1 again.

•

When pressing the buttons on the primary remote
control, make sure that you have selected the FM
station using the primary remote control.

One of the advantages of the RDS service is that you can locate a particular kind of program from the
preset channels by specifying the PTY codes.

Press PTY SEARCH while listenning to an
FM station.

1

Press the PTY-or PTY+until the PTY code
you want appears on the display.

•

The display gives you the PTY codes described
to the right.

2

Press PTY SEARCH again, while the PTY
code selected in the previous step is still on
the display.

•

The center unit searches 15 preset FM
stations,stops when it finds the one you

have selected, and tunes in that station.

3

Display

NEWS

AFFAIRS

INFO

SPORT

EDUCATE

DRAMA

CULTURE

SCIENCE

VARIED

POP M

ROCK M

M.O.R.M

LIGHT M

CLASSIC

OTHER M
WEATHER

FINANCE

CHILDREN

SOCIAL A
RELIGION
PHONE IN

TRAVEL

LEISURE

JAZZ
COUNTRY
NATION M

OLDIES

FOLK M

DOCUMENT

Program Type

• News including an announced opinion and
report

• Several matters including a current incident,
documentary, discussion and analysis.

• Information including weights and measures,

returns and forecast, matters interesting the
customer, medical information, etc.

• Sports

• Education

• Drama-Radio serial, etc.

• Culture-National or local culture including the
religious problem, social science, language,
theater,etc.

• Natural science and technology

• Others-Speech, amusing program (quiz,
game), interview, comedy and satirical play,
etc.

• Pop music

• Rock music

• Current contemporary music considered to be
“easylistening.”

• Light classical music- Classical music and
instrumental and chorus music

• Heavy classical music-Orchestra music,
symphony, chamber music and opera

• Other music - Jazz, R&B country music

• Weather

• Finance

• Children’s programmes

• Social affairs

• Religion

• Phone in

• Travel

• Leisure

• Jazz

• Oldies Music

• Folk Music

• Country Music

• National

• Documentary

4241

RADIO OPERA TION

44

Convenient Functions

Press the SLEEP button.

•

SLEEP : OFF ➝15 ➝30 ➝45 ➝60 ➝90 ➝120MIN will be selected in turn.

You can set the time that this unit will shut itself off.

To Check Sleep Timer

Press SLEEP button.

•

The remaining time before this unit will shut itself off is displayed on the display.

•

Pressing the button again changes the sleep time from what you have set earlier.

To Cancel Sleep Timer

•

Press SLEEP button until SLEEP : OFF appears on the display.

To Output Sound Again

Press MUTE button again.

•

MUTE will disappear and sound will Output.

Press the MUTE button.

•

MUTE appears on the display.

This function is useful what answering a doorbell or telephone call.

Connect the headphone to the headphone jack and listen to
music.

Use headphones (not supplied) for private listening pleasure.

Press the MUTE button.

•

MUTEappears on the display.

The unit automatically back on in 5 seconds.

Do not volume up when you use headphone.
It may damage your hearing.

43

•

Sleep , Mute, Display Off function will work only in Remote
Control.

Sleep Timer Function

Mute Function

Reset Function

Using Headphone

REMOTE CONTROL

REMOTE CONTROL

Caution!

MISCELLANENOUS

Press the DISPLA Y OFFbutton.

•

Each time you press this button, the display is turned on or off.

You can turn the display off to prevent the dazzling light or when you go to bed.

Turning Display On/Off

REMOTE CONTROL

Press “0” button five times and then press ENTER button.

Press

…,†buttons to select “YES”.

REMOTE CONTROL

1

2
3

Using the RESET function will erase all stored settings.
Do not use this unless necessary.

Caution!

46

Operating TV with Remote Control

45

•

The remote control may not work on some brands of TVs. Also, some operation may not be
possible depending on your brand of TV.

•

If you do not set the remote control with the code for your brand of TV, the remote control will work
on a Samsung TV by default.

1

Press MODE button to make the TV

indicator on the remote control flash.

2

Press POWER( ) button to turn on the

TV.

3

Point the remote control toward the TV.

4

While holding down POWER( ) button,

enter the code corresponding to your brand
of TV.

•

If the code matches the TV's code, the TV will be turned off.

•

If there is more than one code listed for your TV in the table, enter
one at a time to determine which code works.

Ex) For a ‘Samsung’ TV

While holding down POWER button, use the Numeric buttons
to enter 00, 01, 02, 03, 04, and 05.

•

You can use the TV POWER, VOLUME, CHANNEL, and Numeric
buttons (0~9).

5

If TV is turned on or off when you press the
power button of the remote control, the
setting is completed.

Code Number Brand Code Number Brand Code Number Brand

ADMIRAL(M.WARDS)

056, 057, 058
A MARK 001, 015
ANAM 001, 002, 003, 004,005,

006, 007, 008, 009, 010,

011, 012, 013, 014
AOC 001, 018, 040, 048
BELL & HOWELL(M.WARDS)

057, 058, 081
BROCSONIC 059, 060
CANDLE 018
CETRONIC 003
CITIZEN 003, 018, 025
CINEMA 097
CLASSIC 003
CONCERTO 018
CONTEC 046
CORONADO 015
CRAIG 003, 005, 061, 082, 083,

084
CROSLEX 062
CROWN 003
CURTISMATES 059, 061, 063
CXC 003
DAEWOO 002, 003, 004, 015,016,

017, 018, 019, 020, 021,

022, 023, 024, 025, 026,

027, 028, 029, 030, 032,

034, 035, 036, 040, 048,

059, 090, 099, 100
DAYTRON 040
DYNASTY 003
EMERSON 003, 015, 040, 046, 059,

061, 064, 082, 083, 084,

085
FISHER 019, 065, 103
FUNAI 003
FUTURETECH 003
GENERAL ELECTRIC(GE)

006, 040, 056, 059, 066,

067, 068
HALL MARK 040
HITACHI 015, 018, 050, 059, 069
INKEL 045
JC PENNY 056, 059, 067, 086
JVC 070
KTV 059, 061, 087, 088
KEC 003, 015, 040
KMC 015
LG(GOLDSTAR)

001, 015, 016, 017, 037,

038, 039, 040, 041, 042,

043, 044, 054, 086

LUXMAN 018
LXI(SEARS) 019, 054, 056, 059, 060,

062, 063, 065, 071

MAGNAVOX 015, 017, 018, 048, 054,

059, 060, 062, 072, 089
MARANTZ 040, 054
MATSUI 054
MGA 018, 040
MITSUBISHI/MGA

018, 040, 054, 059, 060,

075, 101
MTC 018
NEC 018, 019, 020, 040, 059,

060
NIKEI 003
ONKING 003
ONWA 003
PANASONIC 006, 007, 008, 009, 054,

066, 067, 073, 074
PENNEY 018
PHILCO 003, 015, 017, 018, 048,

054, 059, 062, 069, 090
PHILIPS 015, 017, 018, 040, 048

054, 062, 072, 112, 114,

117, 118
PIONEER 063, 066, 080, 091
PORTLAND 015, 018, 059
PROTON 040
QUASAR 006, 066, 067
RADIO SHACK 017, 048, 056, 060, 061,

075
RCA/PROSCAN 018, 059, 067, 076, 077

078, 092, 093, 094
REALISTIC 003, 019
SAMPO 040
SAMSUNG 000, 015, 016, 017, 040,

043, 046, 047, 048, 049,

054, 059, 060, 098
SANYO 019, 061, 065, 101, 102,

103, 104
SCOTT 003, 040, 060, 061
SEARS 015, 018, 019
SHARP 015, 057, 064, 101, 105,

106, 115
SIGNATURE 2000 (M.WARDS)

057, 058
SONY 050, 051, 052, 053, 055,

101
SOUNDESIGN 003, 040
SPECTRICON 001
SSS 018

SYLVANIA 018, 040, 048, 054, 059,

060, 062
SYMPHONIC 061, 095, 096
TATUNG 006
TECHWOOD 018
TEKNIKA 003, 015, 018, 025
TMK 018, 040
TOSHIBA 019, 057, 063, 071, 101

107, 109, 110, 111, 113
VIDTECH 018
VIDECH 059, 060, 069
WARDS 015, 017, 018, 040, 048,

054, 060, 064
YAMAHA 018
YORK 040
YUPITERU 003
ZENITH 058, 079
ZONDA 001
DONGYANG 003, 054
LOWE 054
FINLUX 054, 109, 114
YOKO 054
LOEWE OPTA 054, 114
PHONOLA 054, 112, 114
RADIOLA 054, 112
SCHNEIDER 054
AKAI 103
GRUNDIG 108, 109, 113, 119, 120,

121
BLAUPUNKT 108
SIEMENS 108
CGE 113
IMPERIAL 113
MIVAR 113
SABA 114
BANG&OLUFSEN

114
BRIONVEGA 114
FORMENTI 114
METZ 114
WEGA 114
RADIOMARELLI

114
SINGER 114
SINUDYNE 114
TELEFUNKEN 116

TV Brand Code List

MISCELLANENOUS

48

Operating VCR (DVD) with Remote Control

47

•

The remote control may not work on some brands of VCR (DVD)s. Also, some operations may not
be possible depending on your brand of VCR (DVD).

•

If you do not set the remote control with the code for your brand VCR (DVD), the remote control
work on a Samsung VCR (DVD) by default.

1

Press MODE button to make VCR indicator

on the remote control flash.

2

Press POWER( ) button to turn on the

VCR (DVD).

3

Point the remote control toward the VCR
(DVD).

4

While holding down POWER( ) button,

enter the code corresponding to your brand
of VCR (DVD).

•

If the code matches the VCR (DVD)'s code, the VCR (DVD) will
be turned off.

•

If there is more than one code listed for your VCR (DVD) in the
table, enter one at a time to determine which code works.

Ex)For a ‘Samsung’ VCR (DVD)

While holding down POWER( ) button, use the Numeric
button to enter 00, 32~45, 87, and 88.

•

If you operate DVD, press Device Select button to make DVD
indicator on the remote control flash.

•

You can use VCR (DVD) POWER, VOLUNE, PLAY, PAUSE,
STOP, SKIP and Numeric button (0~9).

5

If VCR (DVD) is turned on or off when you press
the power button of the remote controller, the
setting is completed.

Brand Code Number Brand Code Number Brand Code Number

Code Number Brand

ADMIRAL(M.WARDS)

043, 106
AWIA 044, 045, 046
AKAI 088, 089, 090
ANAM 001, 002, 003, 004, 005,

033
AOC 091
AUDIO DYNAMIC

019, 047, 092
BELL & HOWELL(M.WARDS)

048, 093
BROKSONIC 092

,

094, 095

CANON 001

,

033, 049, 091
CAPEHART 011
CITIZEN 050
CRAIG 050

,

072, 096
CRITERION 051
CURTIS MATHES

001, 031, 032, 033, 044,
091

DAEWOO 006

,

007, 008, 009, 010

,

011, 012, 013, 014, 015

,

016, 017, 018, 046, 051

,

091
DAYTRON 011
DBX 019

,

047, 052, 092

EMERSON 025

,

031, 032, 044, 046

,

094, 095, 097, 098, 099
FISHER 009

,

048, 053, 054, 055

,

100
FUNAI 044
GENERAL ELECTRIC(GE)

001, 031, 032, 033, 056

,

091
GO VIDEO 059

,

060, 061

HARMAN KARDON

019
HITACHI 020

,

021, 049, 054, 062

,

100
HQ 051
INSTANT REPLAY

001, 033, 049, 091
JCL 001

,

033
JCP 025
JC PENNY 047

,

048, 052, 062, 091

,

092

JVC 001

,

033, 047, 052, 063

,

064, 065, 092

KENWOOD 047

,

050, 052, 092
LG(GOLDSTAR) 019

,

020, 021, 022, 023

,

024, 025, 026, 027, 028

,

029, 030, 050

LXI(SEARS) 020

,

025, 044, 048, 050

,

053, 054, 055, 062, 100
MAGIN 072
MAGNAVOX 001

,

031, 032, 033, 049

,

066, 067, 091
MARANTZ 001

,

019, 033, 047, 052

,

092, 110
MARTA 025

,

050

MEI 001

,

033

MEMOREX 001

,

025, 033, 054, 091

,

100

MINOLTA 020

,

021, 062

MITSUBISHI/MGA

068, 069, 070, 101, 102
MTC 072
MULTITECH 044

,

057, 069

NEC 019

,

047, 052, 057, 092

OLYMPIC 049

,

091
OPTIMUS 101
ORION 103
PANASONIC 001

,

004, 033, 049, 067

,

091, 107

PENNEY 019

,

020, 072
PENTAX 001

,

020, 021, 033, 062
PHILCO 001

,

033, 046, 049, 091

,

094

PHILIPS 001

,

030, 033, 049, 050

,

066, 091
PILOT 025
PIONEER 049
PORTLAND 011
QUASAR 001

,

033, 049, 067, 091

,

107, 108
RICO 036
RCA/PROSCAN

001, 020, 021, 031, 032

,

033, 049, 051, 062, 066

,

070, 091, 104
REALISTIC 001

,

009, 025, 033

,

044, 048, 054, 091,

101

, 105

SAMSUNG 000, 006, 031, 032, 057

,

058, 071, 072, 073, 074

,

075, 076, 077, 078, 079

,

080, 081
SANYO 008

,

009, 046, 048, 050

,

054, 058, 093, 100
SANSUI 092
SCOTT 006

,

051, 054, 057, 069

,

070, 100, 101
SEARS 020

,

021, 025

SHARP 043

,

105, 106
SINGER 096
SIGNATURE 2000 (M.WARDS)

043, 044, 054, 100, 106
SHINTOM 096
SONY 034

,

035, 036, 037, 038

,

039, 040, 041, 042,082

,

083, 084, 085, 086
STS 020
SYLVANIA 001

,

033, 044, 049, 066

,

091
SYMPHONIC 044
TANDY 009

TASHIRO 050
TATUNG 047

,

052, 092

TEAC 044

,

047, 052, 092

TECHNICS 001

,

033, 049, 091

TEKNIKA 001

,

025, 033

TOSHIBA 006

,

051

TOTEVISION 025

,

072
TAEKWANG 087
UNITECH 072
VECTOR RESEARCH

019

VIDEO CONCEPTS

019
VIDEOSONIC 072
WARDS 001

,

020, 031, 032, 033

,

043, 050, 054, 072, 100

,

105, 106, 109
YAMAHA 019

,

047,048, 052, 092

,

ZENITH 019, 047,048, 052, 092

DENON 003, 032
DOONOON 019
DMTECH 017
FISHER 002
GE 006
HARMAN/KARDON

012
JVC 010

,

013
KENWOOD 008
LG 001
MAGNAVOX 004
MITSUBISHI 005

,

016
ONKYO 004

,

014
OPTIMUS 011
PANASONIC 021
PROSCAN 006
PHILIPS 004

,

023
PIONEER 007

,

011, 022, 025
RCA 006
SAMSUNG 000

,

027
SANYO 002
SONY 015, 020
THETA DIGITAL

011
TOSHIBA 004, 018
YAMAHA 009, 033
ZENITH 004, 024
TAEGWANG 026
PS2 028
X-BOX 029
APEX 030
MARANTZ 031

VCR Brand Code List

DVD Brand Code List

MISCELLANENOUS

50

Before Calling for Service

49

Symptom Check Remedy

There is no sound from rear

center speaker

•

Is the rear center speaker connected

properly?

•

Is the SB SPK (Rear Center) selected

to NONE in Speaker Setup?

•

Is Surround Mode selected to EX/ES

•

Refer to page 9~10 to connect it properly.

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Refer to page 35~36 to select Surround

Mode to EX/ES.

Can't select EX/ES Mode.

•

Is SB SPK (Rear Center) selected to

NONE in Speaker Setup?

•

Is the input signal selected properly?

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Use 5.1 channel external component.

Can't select Dolby Pro Logic

llx Mode.

•

Is the input signal selected properly?

•

Select 2 channel Dolby Digital, PCM, and

Analog input signal.

There is no sound when
playing DTS encoded DVD
and CD.

•

Is analog input selected?

•

Check whether digital external component

is properly connected and refer to page 19
to select the digital input.

Can't select NEO:6 Mode.

•

Is the input signal selected properly?

•

Use PCM and Analog input signal.

Product Protection Function

DC Protection Circuit

•

If DC is output from output connector, DC protection circuit

works automatically to protect the speaker.

Heat Protection

•

Protection function works if the main unit is overheated or power

transformer is overheated.
appears in the display when the “ ” function
works.

- If speaker terminal is shorted

- If speaker cord is shorted
If there is no problem when you turn it on again after turning it
off, PROTECTION mark will disappear on the display and the
unit will work properly.

•

If PROTECTION appears on the display,
check whether speaker terminal is shorted
and then turn on the device.

√√

œœ

Symptom

Check Remedy

Can't turn it on.

It does not work when the
button is pressed.

Sound is not produced.

Picture does not appear when
the function is selected.

•

Is the power code plugged into the outlet?

•

Isn’t the air too dry to cause

electrostatics?

•

Are the speaker and external

component connected properly?

•

Does the Mute function work?

•

Is the volume set to minimum?

•

Is the speaker setup selected to

NONE?

•

Isn’t the external component connected

properly?

•

Connect the power plug to the outlet.

•

Disconnect the power plug and connect it

again.

•

Properly connect it.

•

Properly connect it.

•

Press Mute button to cancel the function.

•

Adjust the volume.

•

Refer to page 17~18 to select LARGE,

SMALL or YES.

There is no sound from

center speaker

•

Is the center speaker connected properly?

•

Is C.SPK (Center) selected to NONE in

Speaker Setup?

•

Is the Surround Mode selected to Stereo?

•

Refer to page 9~10 to connect it properly.

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Refer to page 27~38 to select other

Surround Mode.

Remote controller does not
work.

There is no sound from rear

speaker.

The sound from each device
is changed during stereo
playback.

Can't receive broadcasting.

•

Is AM or FM antenna connected

properly?

•

Are the batteries exhausted?

•

Is the distance between remote

control and main unit proper?

•

Is the rear speaker connected

properly?

•

Is S.SPK (Rear) set to NONE in

Speaker Setup?

•

Is Surround Mode selected to Stereo?

•

Refer to page 17~18 to connect it properly.

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Refer to page 27~38 to select other

Surround Mode.

•

Replace with new batteries.

•

Operate at close distance.

•

Properly connect the antenna.

•

If the input strength of antenna connector is

weak, install the FM antenna at the place
with good reception.

•

Is the left/right speaker or left/right

input/output code connected
properly?

•

Check the left/right channel and properly

connect it.

MISCELLANENOUS

51

Specifications

❈S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES-17 filter.

VIDEO

OUTPUT

Power Supply

Standby Power Consumption

Power Consumption

Weight

Dimensions (W x H x D)

Operating Temperature Range

Operating Humidity Range

Frequency Response

Usable Sensitivity

S/N Ratio

Distortion

Stereo Separation

Tuner Output Level

Frequency Response

S/N Ratio

Usable Sensitivity

Distortion

Rated Output

Front Speaker(Left+Right)

Center Speaker

Rear Speaker(Left+Right)

Rear Center Speaker

Input Sensitivity/Impedance

S/N Ratio(Analog Input/5.1CH Analog Input)

Separation(1KHz)

Analog Input/5.1CH Analog Input

Digital Input/96KHz PCM

TV Format

Input Level/Impedance

Output Level/Impedance

Video Frequency Response

Component Video Frequency Response

S/N Ratio

GENERAL

FM TUNER

AM TUNER

AMPLIFIER

FREQUENCY

RESPONSE

230V, 50 Hz

0.9W

110W

4.65 kg

430 x 65 x 350 mm

+5° C~+35° C

10%~75%

87.5~108.0MHz

12dBf

MONO/STEREO 55/55dB

MONO/STEREO 0.3/0.8%

30dB

1KHz, 75KHz Dev

522~1611KHz

40dB

60dB uV/m(Loop Antenna)

2% (MOD:80%)

20Hz~20KHz/THD = 1%

6 Ω 90W/CH

6 Ω 90W/CH

6 Ω 90W/CH

6 Ω 90W/CH

450mV/47kΩ

80dB

60dB

20Hz~20KHz(+_3dB)

20Hz ~44KHz(+_3dB)

NTSC/PAL

1Vp-p/75 Ω

1Vp-p/75 Ω

5Hz to 10KHz(-3dB)

5Hz to 40KHz(-3dB)

60dB

52

Memo