SAMSUNG AS180UE0K Service Manual

ROOM AIR CONDITIONER

AS180UE/AS181UE AS180UD/AS181UD AS-2408BR

SERVICE

Manual

CONTENTSAIR CONDITIONER

1. Pre c a u t i o n s

2. Product Specifications

3. Operating Instructions and I n s t a l l a t i o n

4. Disassembly and Reassembly

5. Tro u b l e s h o o t i n g

6. Exploded Views and Parts List

7. Block Diagrams

8. PCB Diagrams

9. Wiring Diagrams

10. Schematic Diagrams

Printed in Korea. Code No. DB81-10161A(1)

1. Precautions

1) Remove power cable from power outlet. Remove power cable from an outlet prior to disassembly for repair. When the power cable is removed wait for at least 1 minute and measure the voltage between the + and - terminal of the large capacity electrolyti capacitor using a tester. Make sure that the voltage is less than DC 10V, then starts repairing.

2) Warning about electrical shock If you cannot avoid checking the circuits with power not disconnected pay special attention not to touch live parts to avoid electric shock.

3) Use proper parts Use genuine parts of a model if parts need to be replaced. (It is recommended that parts are replaced rather than repaired, to avoid electrical contact. Customers should refrain from repairing parts themselves as this can be extremely dangerous.)

4) Use proper tools Use proper tools for repair and be familiarized with handling test equipment. Using worn out tools may result in problems such as intermittent contact, etc.

dangerous

5) Lead wire or power cable damaged Check if lead wire or power cord is damaged prior to repair, and replace if damaged.

6) Avoid tapping a power cord Tapping a power cable or using an extension cord from a power outlet is dangerous and should be avoided. It may result is malfunctioning or fire.

7) Checking insulation Be sure to check insulation resistance when assembly is completed. (Check insulation resistance between the power cord plug and ground terminal using an ohm meter and check if it is greater than 30MΩ prior to applying the power.)

8) Check grounding Check grounding status and fix it if not sufficient.

9) Check installation condition Check installation condition and fix insufficient conditions. If it is still not satisfactory find another area for installation.

10) Child care It is recommended to have children stay away the units when the repair is being done to avoid accidents.

Cleaning

No inter connection

Brilliantly

Clean the unit and the area arount it. Let the customer know that the unit has been repaired.

Samsung Electronics

1-1

M E M O

1-2

Samsung Electronics

2. Product Specifications

2-1 AS180UE/AS181UE/AS180UD/AS181UD/AS-2408BR

M o d e l

I t e m

Ty p e C o o l i n g B T U / h D e h u m i d i t y i n g P I N T S

P e rf o rm a n c e

P o w e r E l e c t r i c a l C h a r a c t e r i st i c s

P ro d u c t

Maximum operation Condition

Low temp. heating B T U / h Air volume C o o l i n g m3/ m i n N o i s e C o o l i n g d B E n e rgy efficiency ratio C o o l i n g B T U / h . W Power V- H z Power Consumption C o o l i n g W Operating Curre n t C o o l i n g A Power factor C o o l i n g % S t a rting curre n t A Power cable L e n g t h m

Number of core wire Fuse capacity A Outer Width x Height m m dimension x Depth i n c h We i g h t k g Coolant pipe L i q u i d OD(mm) x L(m)

C o o l a n t OD(mm) x L(m) Drain hose ID(mm)x L(m) C o m p ressor Ty p e

M o t o r Ty p e

Rated input W Blower Ty p e

M o t o r Ty p e

Rated input W

Heat exchanger Coolant control unit F reezer oil capacity c c Coolant to charg e ( R - 2 2 ) g Cooling test Condition

AS180UE/AS181UE

Indoor unit Outdoor unit

Wa l l - m o u n t i n g

1 7 , 5 0 0

3 . 4

1 3 . 8

4 5 5 5

9 . 7

1-220 / 240-50

1 8 0 0

8 . 0

93.8 (at 240V) 4 0

6 . 2

3G x 2.5mm2/ A re a

3 . 1 5 1 0 5 0 x 2 9 8 x 1 8 0 7 8 7 x 6 2 0 x 3 2 0 4 1 . 3 4 x 1 1 . 7 3 x 7 . 0 9 3 0 . 9 8 x 2 4 . 4 x 1 2 . 6

1 3 4 6

ø6.35 x 5 ø12.7 x 5

ø17 x 2000

- R o t a ry

- -

- 1 8 5 5

C ro s s - f a n P ro p e l l e r

R e s i n S t e e l

3 0 6 0

2Row 12Step 2Row 24Step

C A P I L L A RY TUBE

6 0 0

1 , 5 8 0

INDOOR UNIT : DB 27°C W B 1 9 ° C OUTDOOR UNIT : DB35°C W B 2 4 ° C INDOOR UNIT : DB 32°C W B 2 3 ° C OUTDOOR UNIT : DB 43°C W B 2 6 ° C

AS180UD/AS181UD

Indoor unit Outdoor unit

Wa l l - m o u n t i n g

4 5 5 5

1-200 / 220-50

3G x 2.5mm2/ A re a

3 . 1 5 1 0 5 0 x 2 9 8 x 1 8 0 7 8 7 x 6 2 0 x 3 2 0 4 1 . 3 4 x 1 1 . 7 3 x 7 . 0 9 3 0 . 9 8 x 2 4 . 4 x 1 2 . 6

1 3 4 6

- R o t a ry

- -

- 1 8 5 5

C ro s s - f a n P ro p e l l e r

R e s i n S t e e l

3 0 6 0

2Row 12Step 2Row 24Step

1 7 , 5 0 0

3 . 4

1 3 . 8

9 . 7

1 8 0 0

9 . 0

90.9 (at 220V) 4 0

6 . 2

ø6.35 x 5 ø12.7 x 5

ø17 x 2000

C A P I L L A RY TUBE

1 , 5 5 0

AS-2408BR

Indoor unit Outdoor unit

Wa l l - m o u n t i n g

4 6 5 6

1 - 2 2 0 - 6 0

3G, AW G 1 4

3 . 1 5 1 0 5 0 x 2 9 8 x 1 8 0 7 8 7 x 6 2 0 x 3 2 0 4 1 . 3 4 x 1 1 . 7 3 x 7 . 0 9 3 0 . 9 8 x 2 4 . 4 x 1 2 . 6

1 3 4 6

ø6.35 x 5 ø15.8 x 5

ø17 x 2000

- R o t a ry

- -

- 2 1 5 7

C ro s s - f a n P ro p e l l e r

R e s i n S t e e l

3 0 6 0

2Row 12Step 2Row 24Step

6 0 0

INDOOR UNIT : DB 27°C W B 1 9 . 5 ° C OUTDOOR UNIT: DB35°C W B 2 4 ° C INDOOR UNIT : DB 32°C W B 2 2 . 5 ° C OUTDOOR UNIT: DB 43°C W B 2 5 . 5 ° C

2 2 , 0 0 0

5 . 9

1 4 . 3

1 0 . 5

2 1 0 0

1 0 . 0 9 5 . 4

5 0 6 . 2

C A P I L L A RY TUBE

6 0 0

1 , 6 5 0

Samsung Electronics

2-1

2-2 Dimensions

2-2-1 Indoor Unit

Air out

(Front view)

Air in

(Rear view)

1050

unit : mm

(Remote control unit)

180 63

(Installation plate)

outer edge of

250 145

260 200 100

indoor unit

2-2-1 Outdoor Unit

2-2

(Front view) (Rear view)

582 340 787

Samsung Electronics

3. Operating Instructions and Installation

3-1 Operating Instructions

3-1-1 Name & Function of Key in remote controller

NAMED OF KEY 1 2

FAN SPEED

SWING

ON/OFF

MODE

TURBO

MILD

Q. TIMER

SET

AUTO

Use this button to start and stop air conditioner. Each time you press this button,

MODE is changed in the following order.

"AUTO" "COOL" "DRY" "FAN"

Use this button to provide heavy duty cooling for 30 minutes.

Use this button to provide pleasant cooling

for 3 hours.

Set up the reserve or cancel the timer on and timer off quickly.

Each time you press this button, FAN SPEED is changed in the following order. "AUTO" " (L)" " (ME)" " (HI)" NATURAL

Adjusts air flow vertically. Each time you press this button, BLADE-H rotates by 8° (Changable range 50°).

Each time you press this button, BLADE-H rotates within 35° and stop.

FUNCTION OF KEY

ONE SHOT KEY ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

TIME

TIMER/CANCEL

TIMER

TIME

TEMP

SLEEP

ON OFF

(UP)

(DOWN)

(UP)

(DOWN)

Without regard to ON/OFF condition in remote controller, use this button to set current time. Adjust the current time using TIME button. (Data can be transmitted after setting up the time)

Use this button to reserve or cancel the timer on and timer off. Set up the time that operation start. Set up the time that operation stop. If the TIME button is pressed once, the time increase by one

minute during the time set mode, and ten minutes during the timer set mode.

If the TIME button is pressed once, the time decrease by one minute during the time set mode, and ten minutes during the timer set mode.

If the button is pressed once, the setting temperature is increased by 1°C.

If the button is pressed once, the setting temperature is decreased by 1°C.

Use this button for sleep operation. (The SLEEP mode can be selected at COOL mode.

ONE SHOT KEY

ONE SHOT KEY ONE SHOT KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

CONTINUOUS KEY

ONE SHOT KEY

Samsung Electronics

3-1

Operating Instructions and Installation

3-1-2 Main controller function.

1. A U TO MODE: In this mode, operation mode (COOL) is selected automatically by the room temperature of initial operation.

Operation Type

Cool Operation (Set Temp:24°C + ∆T)

∆T= -1°, -2°C, 0°C, +1°C, +2°C ∆T is controlled by setting temperature

up/down key of remote contro l l e r

2. C O O L MODE: The unit operates accord i n g to the diff e rence between the setting and room temperature . The setting temperature range is 1 8 ° C t h rough 30°C.

3. D RY MODE: The unit is operated at comp ressor on state re g a rdless of room tempera t u re for an initial 30 minutes of dehumidification operation, and the indoor fan motor is automatically operated due to the tempera t u re diff e rence between the room temperat u re and set temperature . The compressor is automatically contro l l e d due to the temperature diff e rence between room temperature and set temperature after operation of 30 minutes. * Set temperature: 18°C~30°C * Protective function: Low temperature release. (Prevention against fre e z e )

4. TURBO MODE: This mode is available only in A U TO, COOL m o d e . When this button is pressed at first, the air conditioner is operated “powerful” state for 30 minutes re g a rdless of the set temperat u re, room temperature . When this button is pressed again, or when the operating time is 30 minutes, turbo operation mode is canceled and returned to the previous mode.

5 . MILD MODE: This mode is available only

in A U TO, COOL m o d e . When this button is pressed at first, the air conditioner is operated in its current state for 3 hours. The setting temperature is automatically raised by 3°C. When this button is pressed again or when

the operating time is 3 hours, mild operation mode is canceled and returned to the p revious mode.

6 . S L E E P MODE: Sleep mode is available only

in COOL m o d e .

The operation will stop after 6 hours.

* In COOL mode : The setting temperature

is automatically raised by 1°C each 1hour

When the temperature has been raised by

total of 2°C, that temperature is main-

t a i n e d .

7. FAN SPEED: Manual (3 step), Auto (4 step), N a t u r a l Fan speed automatically varies depending on both the diff e rence between setting and

the room temperature .

8 . C O M P U L S O RY O P E R ATION:

For operating the air conditioner without the remote contro l l e r. The operating is the same function that A U TO MODE in the remote contro l l e r. * Set temperature: 22°C

3-2

Samsung Electronics

Operating Instructions and Installation

9 . SWING: BLADE-H is rotated vertically by

the stepping motor. * Memory louve: When ON/OFF button is p ressed at stop state, the BLADE-H re t u r n s to its original location which is operating state before stop. * Swing auto: The BLADE-H can ro t a t e within about 35° in the original position set by the SWING SET button. * Swing set: Press the SWING SET button, then the blade rotates vertically by 8° The BLADE-H location is dispalyed on REMOTE CONTROL. (total 7 steps)

1 0 . Q.TIMER: Q. timer (quick timer) allows

reservation or cancel the timer on and timer o ff quickly. When Q.timer button is pressed at operating state, LCD displays the polling state s e q u e n t i a l l y. The LCD also displays the time re m a i n i n g .

1 2 . SELF TEST

* Interruption of electric power and Power o n . * Abnormal condition of the room sensor. * Indoor unit fan motor lock. * Abnormal condition of the indoor unit's heat exchanger sensor.

1 3 . TIME SHORTENING: If the "Time short"

connector pin is shorted on the main P. C. B, the compressor's three minutes delay function is cancelled, and each operation time is shortened to one fiftieth of its original time.

1 4 . BUZZER SOUND: Whenever the ON/OFF

button is pressed or whenever change occurs to the condition which is set up or select, the compulsory operation mode, buzzer is sounded "beep".

11 . TIMER: The air conditioner is turned

ON/OFF at a specified time using TIMER O N / O F F.

* Timer LED lights on.

Samsung Electronics

3-3

3-2 Installation

3-2-1 Selecting Area for Installation

Select an area for installation that is suitable to the customer's needs.

3-2-1(a) Indoor Unit

1 . Make sure that you install the indoor unit in

an area providing good ventilation. It must not be blocked by an obstacle affecting the airflow near the air inlet and the air outlet.

2 . Make sure that you install the indoor unit in

an area allowing good air handling and endurance of vibration of the indoor unit.

3. Make sure that you install the indoor unit in an area where there is no source of heat or vapor nearby.

4 . Make sure that you install the indoor unit in

an area from which hot or cool air is spre a d evenly in a ro o m .

5 . Make sure that you install the indoor unit in

an area away from TVs, audio units, cordless phones, fluorescent lighting fixture s and other electrical appliances (at least 1 m e t e r ) .

6 . Make sure that you install the indoor unit in

an area which provides easy pipe connection with the outdoor unit, and easy drainage for condensed water.

7. Make sure that you install the indoor unit in an area which is large enough to accomodate the measurements shown in figure on the next page.

3-2-1(b) Outdoor Unit

1 . Make sure that you install the outdoor unit

in area not exposed to the rain or direct sun l i g h t .

(Install a separate sunblind if exposed to

d i rect sun light.)

2 . Make sure that you install the outdoor unit

in area allowing good air moment, not amplifying noise or vibration, especially to avoid disturbing neighbours.

(Fix the unit firmly if it is mounted in a

high place.)

3 . Make sure that you install the outdoor unit

in area providing good ventilation and which is not dusty. It must not be blocked

by any obstacle affecting the airflow near

the air inlet and the air outlet.

4 . Make sure that you install the outdoor unit

in area free from animals or plants.

5 . Make sure that you install the outdoor unit

in area not blocking the traff i c .

6. Make sure that you install the outdoor unit in area easy to drain condensed water fro m the indoor unit.

7. Make sure that you install the outdoor unit in area which provides easy connection within the maximum allowable length of a

coolant pipe (15 meters).

Note

1. Add 10 grams of refrigerant (R-22) for

every 1 meter if the pipe length exceeds the standard pipe length of 5 meters.

2. Maintain a height between the indoor and

outdoor units of less than 3 meters.

8 . Make sure that you install the outdoor unit

in an area which is large enough to accommodate the measurements

shown in figure on the next page.

3-2-1(c) Remote Control Unit

1 . Make sure that you install the remote con-

t rol unit in an area free from obstacles such

as curtains etc, which may block signals

f rom the remote control unit.

2. Make sure that you install the remote cont rol unit in an area not exposed to

d i rect sunlight, and where there is no sourc e

of heat.

3. Make sure that you install the remote con-

t rol unit in an area away from TVs, audio

units, cordless phones, fluorescent lighting f i x t u res and other electrical appliances (at least 1 meter).

Caution :

It is harmful to the air conditioner if it is used in the following environments: greasy areas (including areas near machines), salty areas such as coast areas, areas where sulfuric gas is present such as hot spring areas. Contact your dealer for advice.

3-4

Samsung Electronics

Operating Instructions and Installation

3-2-2 Installation diagram of indoor unit and outdoor unit

GAS LEAK TEST Slope of drain hose * Piping may be laid to the rear, left, right or down.

Avoid up

Indoor unit check points

slopes

Right

Left

Outdoor unit check points

* Check for gas leak from the flare nut

connections with leak detector.

5 6

250mm

m i n i m u m

Rear

Down

Insulation of pipe connection area

* Perform gas leakage test first, and insulate the pipe

connection area. Use an insulation tube for insulation as shown in figure.

The insulation tube shall be properly finished not to allow any gap.

Left rear

350mm or more

Vinyl tape (purchase locally)

Remote control

Remote control holder

Hole dimension of bolts for the outdoor unit

Insulation tube

Coolant adjustment pro c e d u re

C l a s s

C o n n e c t i o n

pipe lengh

At installation At installation

A i r- p u rg e

m e t h o d

C o o l a n t a d j u s t m e n t u n n e c e s s a ry

5m max

Refer to the

detailed

a i r- p u rg e

p ro c e d u re .

Add 10g of c o o l a n t

5 ~ 1 0 m

<R-22> for e v e ry 1m. (Refer to the detailed c o o l a n t c h a rg e p ro c e d u re . )

Samsung Electronics

Air purg e

m e t h o d

P u rge air using a vacuum pump or an

a d d i t i o n a l c o o l a n t c y l i n d e r.

R e f r i g e r a n t q u a n t i t y

See table r i g h t .

Add 10g of c o o l a n t <R-22> for e v e ry 1m. (Refer to the detailed c o o l a n t c h a rg e p ro c e d u re . )

Fix firmly if installed in an area affected by typhoons.

582

Coolant adjustment pro c e d u re kg .cm

Outer diameter Fixing torque Final torque

ø6.35mm 160 200 ø12.7mm 500 550 ø15.8mm 700 750

Tighten the flare nut by hand first, and tighten firmly with a spanner

C o o l a n t - q u a n t i t y

M o d e l

Coolant quantity

R e m a r k

A S 1 8 0 U E / A S 1 8 1 U E 1 5 8 0 g Self refrigerant is included with shipment.

A S 1 8 0 U D / A S 1 8 1 U D 1 5 5 0 g Self refrigerant is included with shipment.

A S - 2 4 0 8 B R 1 6 5 0 g Self refrigerant is included with shipment.

For more information refer to the Installation Manual.

ø12

3-5

Operating Instructions and Installation

3-2-2(a) Fixing the Installation Plate

CUTTING A HOLE

When the refrigerant piping are hooked up from the rear.

Installation plate

Pipe hole (ø65mm)

MOUNTING THE INSTALLATION PLATE

When the installation plate is directly mounted on the wall.

250mm 145mm

Pipe hole

(ø65mm)

260mm

Installation plate

Indoor unit

Weight

200mm 100mm

Determine the pipe hole position for installation and drill the pipe hole (65mm inner diameter) so that it slants slightly downward.

1. Install the installation plate horizontally on structural members (studs, etc.) in the wall.

2. To mount the installation plate on a concrete wall with anchor bolts, utilize the anchor bolt holes as illustrated in the left figure.

250mm350mm

3. When the anchor bolts are already driven in the wall, also utilize the anchor bolts holes to secure the installation plate. (If an anchor bolt is too long, adjust the projecting length to 20mm or less.)

Mounting at the window frame.

3-6

1. As the left Fig. Fix the wood pillar at the wood frame and install installation plate with screw tap.

2. Fix the wood pillar with enough strength to bear the weight of the indoor unit.

Wood pillarScrew wood

Samsung Electronics

3-2-2(b) Wiring connection(Indoor unit)

1. Open the Grille and remove the screw securing the cover.

AS-24**

2. AS-18**: Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals 1~3. *Each wire is labelled with the corresponding terminal number. AS-24**: Firmly connet the cable connector with connector.(6pin, 4-cable)

3. Assembly every parts by contrary order to disassembly.

3-2-2(c) Piping and drain hose installation

1 . Fix the drain hose right the refrigerant piping.

2. Be careful not to form a slack of the drain hose.

3. Do not allow the piping to jut out from the back of the indoor unit.

4. Insulate both of the refrigerant pipings so that dewing and troubles

may not happen.

5. Be careful in bending the pipes. The bending radius must be

100mm or larg e r.

Assembly cable

Operating Instructions and Installation

Conneitor

AS-18**

Indoor unit

Outdoor unit

Screw

Tape

Piping

Drain hose

A.Right-hand connection with piping C.Under-side connection with pipingB.Left-hand connection with piping

1. Cut out the knock-out piece from the

rightside of the rear body with a knife, etc. Smooth the cut edges.

1. Cut out the knock-out piece from the leftside of the rear body with a knife,

etc. Smooth the cut edges.

2. Cut out the Holder-pipe slit part.

3. Support the above section to be bent with your hand and bend the pipes there.

1. Cut out the knock-out piece from the underside of the rear body with a knife, etc. Smooth the cut edges.

2. Cut out the Holder-pipe on its slit part.

Set the drain hose in the inner part of the indoor unit and the assembly cable in lower part of it. Wind tape round them.

Piping

Assembly cable

Installation plate

Drain hose

Samsung Electronics

3-7

Operating Instructions and Installation

3-2-2(d) Indoor unit installation

DRAINAGE

1. Pass the pipes

Hook here

t h rough the hole in the wall and hook the indoor unit to the i n s t a l l a t i o n plate at the upper and lower hooks.

2. Move the indoor unit to the right and left to make sure that the unit is s e c u rely hooked on to the installation p l a t e .

1. Run the drain hose sloped downward .

2. Do not install the drain hose as illustrated below.

Do not form a rise

3. Put water in the drain pan and make sure that the water is drained outdoor.

4. When connecting the extension drain hose, insulate the inside part of the extension drain hose with shield.

3-2-2(e) Wiring connection(outdoor unit)

AUXILIARY POWER S/W WIRING CONNECTION

Do not put the drain hose end into water

Do not wave the hose

Keep a distance at least 5cm or more

Ditch

Do not put the drain hose end in the ditch

A u x i l i a ry power S/W should be installed near indoor unit so that each access is p o s s i b l e . Main/Outdoor unit power cords are connected to upper/lower terminal of a u x i l i a ry power S/W.

distributind board

Auxiliary

power S/W

Indoor unit connector wire should be connected to both indoor unit connector ( t e rminal board) and outdoor unit term i n a l b o a rd as shown in the figure below.

AS-18**

(POWER CABLE)

(ASSEMBLY CABLE)

AS-24**

(ASSEMBLY CABLE)

EARTH WIRE

EARTH WIRE

3-8

(POWER CABLE)

EARTH WIRE

Samsung Electronics

3-2-2(f) Grounding

(The Parts for this work are optional.)

Operating Instructions and Installation

• A g rounding terminal can be found on the outdoor unit as illustrated.

1. When an existing grounding terminal is avilable. ( G rounding wire of ø1.6mm or larger<solid w i re > o r

2 m m2or larger <standard wire > )

Terminal used exclusively for grounding.

Grounding resistance ; Less than 100 ohms (existing grounding electrode)

2. Use of a grounding electro d e .

• Specifications of grounding electro d e .

Steel coreCarbon plastic

PVC-Insulated(2mm2x3.5m), green Terminal, M4

No. JOB EXPLANATION PRECAUTIONS

1 Determine the • Suitable location • Avoid sandy or gravelly soil as its grounding

grounding position. a) Place that is always dank. resistance is high.

b) Hard soil rather than loose sandy soil. • The grounding wire for the telephone line cannot

be used for the grounding of the air conditioner.

• Unsuitable location • When the grounding electrode is to be installed a) Where there are underground structures or under a place with heavy traffic, its wire must be

facilites such as gas pipes, water pipes, connected firmly with the utmost care. telephone lines, underground cables, etc.

b) A place 2m or less from the lightning arrester

grounding electrode and its cable.

2 Drive the grounding a) Dig a hole to the size illustrated,

electrode into position. and drive in the grounding electrode.

b) Cover the top of the grounding

electrode with excavated soil.

3 Put the grounding a) If the grounding wire is too short, connect an • The grounding wire should be a green

wire in order. extention lead to it. Solder the joint and insulated wire of ø1.6mm or 2mm2or larger.

wrap it with tape. • The soldered joint should not be buried

b) Fasten the grounding wire with staples. underground.

4 Check the a) After grounding work, measure the grounding

workmanship, resistance with a grounding resistance tester. and provide

corrective b) If the resistance is above a specified level, measures if drive the grounding electrode in deeper necessary. or increase the number of grounding

electrodes.

5 Connect the Secure the grounding wire to the

grounding grounding terminal of the air conditioner wire to the air conditioner.

Samsung Electronics

3-9

Operating Instructions and Installation

3-2-2(g) Flare modification

• Tools used

Tightening

knob

Clamp handle

Bar

Yoke

Cutting wheel

Roller

• Flare modification procedure

1) Cut the pipe using a pipe cutter.

Oblique Raughness Burr

3) Insert a flare nut into the pipe and modifty flare.

Cone

2) Remove burrs at the tip of the pipe cut. Caution : Burrs not removed may result

in leakage of gas.

Pipe

Reamer

Point down

3-10

• Unproper flaring

Inclined Surface

damaged

Outer diameter A(mm)

ø6.35mm 1.3 ø12.7mm 2.0 ø15.8mm 2.2

Cracked Uneven

thickness

Samsung Electronics

+ 37 hidden pages