Samsung AM26B1C13 User Manual

ENGLISH

OWNER’S INSTRUCTIONS & INSTALLATION MANUAL

MANUAL DE INSTRUCCIONES & MANUAL DE INSTALACIÓN

MANUEL D’UTILISATION & MANUEL D’INSTALLATION

MULTI-SPLIT TYPE ROOM AIR CONDITIONER ( Cool )

ACONDICIONADOR DE AIRE DOMÉSTICO SISTEMA MULTI SPLIT

( Refrigeración )

CLIMATISEUR DE TYPE MULTIPLE ( Refroidissement )

E S F

DB98-05640A(3)

ESPAÑOL

FRANÇAIS

AM18B1C09 AM26B1C13

AM27B1C07 AM27B1C13

Indoor Unit

UM18B1C2 UM26B1C2

UM27B1C3

Outdoor Unit

Safety Precautions

The following safety precautions must be taken when using your air conditioner.

1 Make sure that the indoor unit is correctly ventilated at all times; do NOT place clothing or other materials

over it.

2 NEVER spill liquid of any kind into the indoor unit. Should this happen, switch off the breaker used for your

air conditioner and contact your installation specialist.

3 Do NOT insert anything between the air flow blades, as the inner fan may become damaged and you may be

hurt. Keep children away from the indoor unit.

4 Do NOT place any obstacles in front of the outdoor unit.

5 If the remote control will not be used for a long time, remove the batteries.

6 Users of this product are cautioned not to attempt repair of this product at their own discretion.

Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased.

7 If the supply cord is damaged, it must be replaced by a special cord or assembly available from the

manufacturer or its service centre.

8 This device must be installed according to the national electrical rules.

9 Before disposing of the remote control it is necessary to remove batteries.

10 The appliance is not intended for use by young children or infirm person without supervision;

young children should be supervised to ensure that they do not play with the appliance.

11 Max current is measured according to IEC standard for safety and current is measured according to

ISO standard for energy efficiency.

The manufacturer does not take any responsibility for any accidents that occur because the air conditioner is not fixed firmly or installed securely, during installing or using the product. In case you experience difficulty in installation, you must use an installation specialist. An accident will occur if the installation is not done as recommends in the installation guide.

CCCCAAAAUUUUTTTTIIIIOOOONN

E-2

Contents

◆

REPARING YOUR AIR CONDITIONER

■ Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

■ View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

■ Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . 6

■ Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■ Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . 8

■ Installing the Remote Controller Holder . . . . . . . . . . . . . . . . . . 8

◆

PERATING YOUR AIR CONDITIONER

■ 5 Way Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

■ Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . 10

■ Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

■ Changing the Room Temperature Quickly . . . . . . . . . . . . . . . 12

■ Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . 13

■ Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

■ Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . 15

■ Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . 15

◆

ROGRAMMING YOUR AIR CONDITIONER

■ Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

■ Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

■ Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

◆

ECOMMENDATIONS FOR USE

■ Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . 19

■ Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . 20

■ Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . 21

■ Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 22

■ Installing a Filter (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

◆

ECHNICAL SPECIFICATIONS

E-3

ENGLISH

View of the Unit

The design and shape are subject to change according to the model.

Indoor Unit

Air filter (under the grille)

Air flow blades (outlet)

Air Inlet

Timer indicator

STANDARD indicator

NATURE indicator

POWER indicator

SILENCE indicator

Remote Control Sensor SAVING indicator

On/Off & 5 Way selection button

◆ For details on the 5 Way, refer to page 9.

NNNNoooottttee

E-4

E-5

ENGLISH

Air Inlet(Rear)

Air Outlet

Connection Valve

Outdoor Unit

UM18B1C2

Outdoor Unit

UM26B1C2

Outdoor Unit

UM27B1C3

Air Inlet(Rear)

Air Outlet

Connection Valve

Remote Control - Buttons and Display

Operating mode

( AUTO, COOL,

DRY, FAN)

Remote control

transmission indicator

Mode selection button

(AUTO, COOL, DRY, FAN)

Turbo/Sleep mode selection button

Swing button

On Timer button

Off Timer button

On/Off & Timer Set/Cancel button

Fan speed adjustment button

Temperature adjustment buttons

Temperature setting

Sleep mode

Turbo mode

Fan speed

Air flow direction

On Timer setting

Off Timer setting

Battery discharge indicator

5 Way selection button

E-6

etting Started

You have just purchased a split type air conditioner and it has been

installed by your installation specialist.

Your Owner’s Instructions contains valuable information on using your

air conditioner. Please take the time to read it as it will help you take full

advantage of the unit’s features.

The booklet is organized as follows.

◆ The following figures are shown on pages from 4 to 6 :

- Indoor and outdoor units

- Remote control(buttons and display) They will help you find the buttons and understand the symbols displayed.

◆ In the main part of the installation book, you will find a series of

step-by-step procedures for each function available.

The illustrations in the step-by-step procedures use three different symbols:

PRESS PUSH HOLD DOWN

E-7

ENGLISH

Inserting the Remote Control Batteries

Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it.

Insert the two batteries, taking care to respect the polarities :

◆ + on the battery with + on the remote control.

◆ - on the battery with - on the remote control.

Close the cover by sliding it back until it clicks into place.

◆ Use two AAA, LR03 1.5V batteries.

◆ Do not use old batteries or different kinds of batteries together.

◆ Batteries may be completely discharged after 12 months, even

◆ if they have not actually been used.

You must insert or replace the remote control batteries when :

◆ You purchase the air conditioner

◆ The remote control does not work correctly

NNNNoooottttee

Installing the Remote Controller Holder

Place the remote controller holder on the wall.

Fix the remote controller holder by tightening the screws.

Put the remote controller into the holder as shown in the figure.

◆ If you want to install the holder easily, you had better install the holder on the wooden frame.

E-8

5 Way Function

Press the (ON/OFF) button one time and then select the desired mode.

To stop the operating, press the (ON/OFF) button until all indicators turn off.

You can select the 5 Way function with operating mode of the air conditioner for more comfortable circumstances. You can use the 5 Way function with the indoor unit as well as the remote control. Thus, you can use this function even though you have lost your remote control.

Using with the indoor unit

To select the 5 Way function with the remote control, press the 5 Way button one or more times until the desired mode is selected.

◆ Each time you press the 5 Way button:

Each 5 Way indicator on the indoor unit lights up in order.

Selecting with the Remote Control

Even if the air conditioner has been turned on via the ON/OFF button on the unit, operations can still be controlled using the remote control as usual.

NNNNoooottttee

To obtain a(n)...

Normal operating

(STANDARD) mode

Then select...

(NATURE) mode

Reducing the uncomfortable temperature gradually

(POWER) mode

High fan speed

(SAVING) mode

Compressor run time reduced

(SILENCE) mode

Fan speed reduces as the temperature decreases

E-9

ENGLISH

Selecting the Automatic Operating Mode

You can start the air conditioner in Automatic mode from your remote control. In the Automatic mode, the standard temperature and the optimum fan speed is selected automatically. You can adjust the standard temperature but not the fan speed.

If the is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears.

Result

: ◆ The indoor unit beeps each time you press the MODE button.

◆ The air conditioner runs in AUTO mode.

You can change modes at any time.

If necessary, press the (On/Off) button. Result: ◆ The 5 Way indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected when the unit was last used.

◆ The indoor unit beeps.

The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being:

◆ Plugged in

◆ Stopped

lt will start up normally after three minutes.

IMPORTANT

NNNNoooottttee

To adjust the standard temperature (The air conditioner automatically set the standard temperature by the current room temperature.), press the TEMPERATURE buttons one or more times.

SET TEMP. SET TEMP. - SET TEMP. SET TEMP.

-4°F/-2°C -2°F/-1°C Standard temperature +2°F/+1°C +4°F/+2°C < When you feel hot > < When you feel chilly >

E-10

Cooling Your Room

If necessary, press the (On/Off) button. Result:

◆

The 5 Way indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected when the unit was last used.

◆ The indoor unit beeps.

The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being:

◆ Plugged in

◆ Stopped

lt will start up normally after three minutes.

IMPORTANT

If the is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears.

Result:

◆

The indoor unit beeps each time you press the MODE button.

◆

The air conditioner runs in COOL mode.

You can change modes at any time.

NNNNoooottttee

To adjust the temperature, press the TEMPERATURE buttons one or more times until the required temperature is displayed. Possible temperatures are between 65°F(18°C) and 86°F(30°C) inclusive.

Result: ◆

Each time you press the TEMPERATURE buttons:

- The temperature is adjusted by 1°F(1°C)

- The indoor unit beeps

◆ The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature; the fan will, however, operate.

Select the fan speed by pressing the FAN button one or more times until the required setting is displayed:

Automatic (rotated : ) Low Medium High

Result

: Each time you press the FAN button, the indoor unit beeps.

To control the direction of the air flow, refer to page 15.

You must select the Cool mode if you wish to adjust the:

◆ Cooling temperature

◆ Fan speed when cooling

E-11

ENGLISH

Changing the Room Temperature Quickly

The Turbo cooling function is used to cool your room as quickly as possible.

EEEExxxxaaaammmmpppplllleeee

: You have just come home and find that the room is very

hot. You wish to cool it down as quickly as possible.

The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected.

If necessary, press the (On/Off) button. Result

: ◆ The 5 Way indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected when the unit was last used.

◆ The indoor unit beeps.

Press the button. Result: ◆ The temperature and fan settings are adjusted automatically.

◆ The air conditioner cools the room as quickly as possible.

◆ After 30 minutes, the air conditioner is reset automatically to the

previous mode, temperature and fan settings. But, if you press the button in DRY or FAN mode,

it will change to AUTO mode automatically.

If you wish to stop the Turbo function before the end of the 30-minute period, press the button one or more times until or disappears.

Result

: The air conditioner is reset automatically to the previous mode,

temperature and fan settings.

To control the direction of the air flow, refer to page

15.

E-12

Removing Excess Humidity

E-13

ENGLISH

If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much.

1 If necessary, press the (On/Off) button.

Result

: ◆

The 5 Way indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected when the unit was last used.

◆ The indoor unit beeps.

The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being:

◆ Plugged in

◆ Stopped

It will start up normally after three minutes.

2 If the is not displayed at the top of the remote control, press the

MODE button on the remote control one or more times until it appears. Result

: ◆

The indoor unit beeps each time you press the MODE button.

◆

The air conditioner runs in DRY mode.

NNNNoooottttee

ee You can change modes at any time.

3 To adjust the temperature, press the TEMPERATURE buttons one or

more times until the required temperature is displayed. Possible temperatures are between 65°F(18°C) and 86°F(30°C) inclusive.

Result

: ◆ Each time you press the TEMPERATURE buttons:

- The temperature is adjusted by 1°F(1°C)

- The indoor unit beeps

◆ The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically.

4 To control the direction of the air flow, refer to page 15.

IMPORTANT

Airing Your Room

If the atmosphere in your room is stale, you can air the room using the Fan feature.

1 If necessary, press the (On/Off) button.

Result

: ◆

The 5 Way indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected when the unit was last used.

◆ The indoor unit beeps.

2 If the is not displayed at the top of the remote control,

press the MODE button on the remote control one or more times until it appears.

Result

: ◆

The indoor unit beeps each time you press the MODE button.

◆

The air conditioner runs in FAN mode.

◆

The temperature is set automatically.

NNNNoooottttee

ee You can change modes at any time.

3 Select the fan speed by pressing the FAN button one or more times

until the required setting is displayed:

Low Medium High

Result

: Each time you press the FAN button, the indoor unit beeps.

4 To control the direction of the air flow, refer to page 15.

E-14

Adjusting the Air Flow Direction Vertically

E-15

ENGLISH

Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner.

1 Press the SWING button one or more times as required.

Result

: The outer blade is adjusted vertically.

RECOMMENDATION When... Adjust the blade to face...

Cooling Upwards.

2 If you want the blade to move up and down automatically when the air

conditioner is operating, press the SWING button. Result

: The blade move up and down, around the base position set.

To stop the blade moving up and down, press the SWING button again.

NNNNoooottttee

If you switch the air conditioner... Then the blade is...

Off Closed completely. On again

Set to the initial position powered.

Adjusting the Air Flow Direction Horizontally

There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally.

1 Adjust each set of inner blades to the required position, by pushing or

pulling them sideways.

+ 35 hidden pages