CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Note to CATV system installer :
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation
slots are not covered. Do not stack anything on top of the player. Do not place the player on modules or other equipment which may
become hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the
Home Theater to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the
power supply, remove the main plug from the wall outlet, especially when left unused for a long period of time.
ENG
PREPARATION
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
This symbol indicates that dangerous voltage which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating and maintenance instructions accompanying
the unit.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Phones
Protect the player from moisture(i.e. vases) , and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...). Disconnect the power cable from the AC supply if the
player malfunctions. Your player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been stored in cold
temperatures.
If transporting the player during the winter, wait approximately 2 hours
until the unit has reached room temperature before using.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the unit.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
12
Features
Multi-Disc Playback & FM Tuner
The HT-Q40 combines the convenience of multi-disc playback capability, including
DVD-AUDIO, DVD-VIDEO, VCD, CD, MP3-CD, WMA-CD, DivX, CD-R/RW, and DVD-R/RW,
with a sophisticated FM tuner, all in a single player.
USB Host Play
You can enjoy media files such as pictures, movies and tunes saved in an MP3 player, digital
camera or USB memory by connecting the storage device to the USB port of the home theater.
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal decoding technology
that improves upon existing Dolby Pro Logic.
DTS (Digital Theater Systems)
DTS is an audio compression format developed by Digital Theater Systems Inc.
It delivers full-frequency 5.1 channel sound.
TV Screen Saver Function
The HT-Q40 automatically brightens and darkens your TV screen
after 3 minutes in the stop mode.
The HT-Q40 automatically switches itself into the power saving mode
after 20 minutes in the screen saver mode.
Power Saving Function
The HT-Q40 automatically shuts itself off after 20 minutes in stop mode.
Customized TV Screen Display
The HT-Q40 allows you to select your favorite image during JPEG, DVD or VCD
playback and set it as your background wallpaper.
AV SYNC Function
Video may lag behind the audio if the unit is connected to a digital TV.
To compensate for this, you can adjust the audio delay time to sync up with the video.
DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby Digital
surround sound and MPEG-2 video compression technology. Now you can enjoy these
realistic effects in the home, as if you were in a movie theater or concert hall.
DVD players and the discs are coded by region. These regional codes must match in order
for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
(Your DVD player will only play DVDs that are labeled with identical region codes.)
Playable Discs
Disc TypeDisc Size Max. Playing Time
DVD-AUDIO
DVD-VIDEO
VIDEO-CD
AUDIO-CD
Divx
Mark (Logo)
COMPACT
DIGITAL VIDEO
COMPACT
DIGITAL AUDIO
Recorded Signals
Audio + Video
Audio + Video
Audio
MPEG4
MP3
5"
3 1/2"
5"
3 1/2"
5"
3 1/2"
5"
3 1/2"
Approx. 240 min. (single-sided)
Approx. 480 min. (double-sided)
Approx. 80 min. (single-sided)
Approx. 160 min. (double-sided)
74 min.
20 min.
74 min.
20 min.
74 min.
20 min.
Disc Recording Format
This product does not support Secure (DRM) Media files.
CD-R Discs
Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the
•
condition of the disc.
Use a 650MB/74 minute CD-R disc.
•
Do not use CD-R discs over 700MB/80 minute as they may not be played back.
Some CD-RW (Rewritable) media, may not be playable.
•
Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you
•
may not be able to fully play the disc.
CD-R MP3 Discs
Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.
•
MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
•
Use discs recorded with a compression/decompression data rate greater than 128Kbps.
•
Only files with the ".mp3" and ".MP3" extensions can be played.
•
Only a consecutively written Multisession disc can be played. If there is a blank segment in the Multisession disc,
•
the disc can be played only up to the blank segment.
If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.
•
For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate
•
(e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.
Amaximum of 500 tracks can be played per CD.
•
A maximum of 300 folders can be played per CD.
•
PREPARATION
Do not use the following types of disc!
LD, CD-G, CD-I, CD-ROM and DVD-ROM discs cannot be played on this player.
•
If such discs are played, a "WRONG DISC FORMAT" message appears on the TV screen.
DVD discs purchased abroad may not play on this player.
•
If such discs are played, a "WRONG REGION CODE" message appears on the TV screen.
Copy Protection
Many DVD discs are encoded with copy protection. Because of this, you should only connect
•
your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain
•
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
CD-R JPEG Discs
Only files with the ".jpeg" and ".JPEG" extensions can be played.
•
If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
•
Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
•
JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
•
Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the
•
disc can be played only up to the blank segment.
A maximum of 9,999 images can be stored on a single CD.
•
When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.
•
Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.
•
CD-R/RW DivX Discs
Since this product only provides encoding formats authorized by DivX Networks, Inc., a DivX file created by the user
•
might not be played.
Software update for unsupported formats is not supported.
•
(Example: QPEL, GMC, resolution higher than 720 x 480 pixels, etc.)
Sections with high frame rate might not be played while playing a DivX file.
•
For more information about the formats authorized by DivX Networks, Inc., visit "www.divxnetworks.net".
•
65
Description
ENG
—Front Panel—
Standby indicator
Power ( ) button
Disc Tray
Function button
Tuning Up & Skip ( ) buttons
Tuning Down & Skip ( ) buttons
Volume
Headphone Jack
Play/Pause ( ) button
Stop ( ) button
Direct Play buttons
Open/
Close button
USB port
—Rear Panel—
External Audio Input Connectors
Cooling Fan
5.1 Channel Speaker
Output Terminals
PREPARATION
Video Output Connector
Connect the TV's video input jacks
(VIDEO IN) to the VIDEO OUT connector.
External Digital Optical
Input Connector
Use this to connect external equipment
capable of digital output.
FM Antenna Connector
COMPONENT VIDEO OUTPUT
Connectors
Connect a TV with component video inputs
to these jacks.
DOLBY DIGITAL indicator
LINEAR PCM indicator
P.SCAN
indicator
DTS
indicator
MPEG indicator
DVD AUDIO indicator
DOLBY PLll indicator
7
GROUP indicator
TITLE
indicator
DSP indicator
CHAPTER indicator
TRACK indicator
PROGRAM indicator
System Status Display
REPEAT indicator
PBC indicator
STEREO indicator
TUNED indicator
RADIO
FREQUENCY
indicator
SPEAKER indicator
DISC(1~5)
indicator
Accessories
Video CableRemote Control
FM Antenna
User's Manual
8
Description
—Remote Control—
ENG
PREPARATION
Insert Remote Batteries
TV button
DVD Receiver button
POWER button
Number(0~9) buttons
REMAIN button
STEP button
SEARCH buttons
VOLUME button
MENU button
DVD button
AUX button
OPEN/CLOSE button
TV/VIDEO, DISC SKIP button
CANCEL button
REPEAT button
Play/Pause button
Tuning Preset/CD Skip button
TUNING/CH button
MUTE button
RETURN button
Cursor/Enter button
TUNER button
USB button
Stop button
Remove the battery
1
cover on the back of
the remote by pressing
down and sliding the
cover in the direction of
the arrow.
Caution
Follow these precautions to avoid leaking or cracking cells:
Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
•
Use the correct type of batteries.Batteries that look similar may differ in voltage.
•
Always replace both batteries at the same time.
•
Do not expose batteries to heat or flame.
•
Insert two 1.5V AAA
2
batteries, paying
attention to the correct
polarities (+ and –).
Replace the battery
3
cover.
INFO button
PL II EFFECT button
PL II MODE button
TUNER MEMORY, P.SCAN button
ZOOM button
SLEEP button
SLOW, MO/ST button
DIMMER button
9
AUDIO button
SUB TITLE button
DSP/EQ button
TEST TONE button
SOUND EDIT button
DIGEST button
LOGO button
SLIDE MODE button
EZ VIEW button
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be
operated at a horizontal angle of up to 30° from the remote control sensor.
10
SRSL
C
L
SW
R
R
L
C
SR
SL
SW
Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Rear Speaker (R)
ENG
Center Speaker
Rear Speaker (L)
CONNECTIONS
Position of the Home Theater
Place it on a stand, cabinet shelf, or under the
•
TV stand.
Front Speakers
Place these speakers in front of your listening
•
position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at
•
the same height as your ear.
Align the front face of the front speakers with the
•
front face of the center speaker or place them
slightly in front of the center speakers.
Center Speaker
It is best to install it at the same height as the front
•
speakers.
You can also install it directly over or under the TV.
•
Selecting the Listening Position
The listening position should be located about 2.5 to 3
times the distance of the TV's screen size away from the
TV. Example: For 32" TVs 2~2.4m (6~8 feet)
For 55" TVs 3.5~4m (11~13 feet)
Rear Speakers
Place these speakers behind your listening position.
•
If there isn't enough room, place these speakers so they face each
•
other.
Place them about 60 to 90cm (2 to 3feet) above your ear, facing
•
slightly downward.
Unlike the front and center speakers, the rear speakers are used
*
to handle mainly sound effects and sound will not come from
them all the time.
Subwoofer
The position of the subwoofer is not so critical.
•
Place it anywhere you like.
Front Speaker (R)
Press and hold the terminal tab.
1
Insert the speaker cord.
2
Release your finger.
3
Caution
Do not let children play with or near the speakers.
•
They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers,
•
make sure that the polarity (+/–) is correct.
Front Speaker (L)
Subwoofer
123
Note
If you place a speaker near your TV set,
•
screen color may be distorted because of
the magnetic field generated by the
speaker. If this occurs, place the speaker
away from your TV set.
Red
Black
11
12
Connecting the Video Out to TV
P.SCAN(Progressive Scan) Function
GB
Choose one of the two methods for connecting to a TV.
METHOD 1
METHOD 2
Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire
picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines
displayed in one pass) to create a clear and detailed picture without visible scan lines.
Press STOP button.
1
If playing a disc, press the STOP button twice so that “STOP”, appears on the display.
•
Press and hold P.SCAN button on the remote control for over 5 seconds.
2
Pressing and holding the button for over 5 seconds will select "Progressive Scan" and "Interlace Scan"
•
alternately.
When you select P.SCAN, "P.SCAN" will appear on the display.
•
To set P.Scan mode for DivX discs, press the P.SCAN button on the remote control for more than
•
5 seconds with no disc in the unit (“'NO DISC" on the display), then load the DivX disc and play.
What is Progressive (or Non-Interlaced) Scanning?
Interlaced Scan (1 FRAME = 2 FIELDS)
Progressive Scan (FULL FRAME)
CONNECTIONS
METHOD 1 Composite Video
Connect the supplied video cable from the VIDEO OUT jack on the back panel of the
system to the VIDEO IN jack on your television.
METHOD 2 Component (Progressive Scan) Video
If your television is equipped with Component Video inputs, connect a component video
cable (not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the
corresponding jacks on your television.
When the Progressive scan mode is selected, the VIDEO output (Yellow) does
Note
•
not output any signal.
...............
Good Quality
...............
Best Quality
In interlaced-scan video, a frame consists of two interlaced fields (odd and even), where each field contains
every other horizontal line in the frame.
The odd field of alternating lines is displayed first, and
then the even field is displayed to fill in the alternating
gaps left by the odd field to form a single frame.
One frame, displayed every 1/30th of a second, contains
two interfaced fields, thus a total of 60 fields are displayed every 1/60th of a second.
The interlaced scanning method is intended for capturing
a still object.
Note
This function works only on TVs equipped with component video inputs (Y, Pr, Pb) that support
•
Progressive Video. (It does not work on TVs with conventional component inputs, i.e., non-progressive
scan TVs.)
Depending on the capabilities of your TV, this function may not work.
•
The progressive scanning method scans one full frame of
video consecutively down the screen, line by line.
An entire image is drawn at one time, as opposed to the
interlaced scanning process by which a video image is
drawn in a series of passes.
The progressive scanning method is desirable for dealing
with moving objects.
13
14
Connecting External Components
Connecting an External Digital / Analog Component
Example: Digital signal components such as a Set-Top Box or CD Recorder.
Analog signal components such as a VCR.
Connecting the FMAntenna
GB
Audio Cable
(not supplied)
If the external analog
component has only one
Audio Out, connect either left
or right.
Connect the Digital Input (OPTICAL) to the Digital Output on the external digital component.
1
Connect AUX (Audio) In on the Home Theater to Audio Out on the external analog
2
component.
Be sure to match connector colors.
•
Optical Cable
(not included)
FM Antenna (supplied)
1
Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal.
Slowly move the antenna wire around until you find a location where reception is good, then fas-
2
ten it to a wall or other rigid surface.
Cooling Fan
The cooling fan supplies cool air to the unit to prevent overheating.
CONNECTIONS
Press AUX on the remote control to select ‘DIGITAL IN / AUX1/AUX2’ input.
3
Each time the button is pressed, the selection changes as follows: AUX1 ➝ AUX2 ➝ DIGITAL IN
•
You can also use the FUNCTION button on the main unit.
•
The mode switches as follows: DVD/CD ➝ DIGITAL IN ➝ AUX1➝ AUX2 ➝ USB ➝ FM
You can connect the Video Output jack on your VCR to the TV, and connect the Audio
Note
•
Output jacks on the VCR to this product.
15
Notes
Please observe the following cautions for your safety.
•
Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise
and may damage it.
•
Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a
newspaper or cloth, heat may build up inside the unit and fire may result.)
This unit does not receive AM broadcasts.
•
16
Before Using Your Home Theater
GROUP 1GROUP 2
TRACK 1TRACK 2TRACK 1TRACK 2TRACK 3
TITLE 1TITLE 2
CHAPTER 1CHAPTER 2CHAPTER 1CHAPTER 2CHAPTER 3
TRACK 1TRACK 2TRACK 4TRACK 5TRACK 3
FILE 1FILE 2
Your Home Theater is capable of playing DVD, VCD, CD, MP3/WMA and JPEG discs.Depending on the disc you
are using, these instructions may vary slightly. Read the instructions carefully before using.
To Operate your Samsung TV and the Home Theater with the HT-Q40's Remote Control
Disc terminology
Groups and tracks (DVD-AUDIO)
DVD-audio is divided into several large sections called "groups" and
•
smaller sections called "tracks". Numbers are allotted to these sections.
These numbers are called "group numbers" and "track numbers".
ENG
Plug the main unit's
power cord into the
1
AC power supply.
Press TV/VIDEO
button to select
4
VIDEO mode on
your TV.
VIDEO
Press TV button to
set the remote to TV
23
mode.
Press DVD RECEIVER
button to switch to
56
DVD RECEIVER
mode.
Press the POWER
button to turn on your
Samsung TV with this
remote.
Press FUNCTION button
on the main unit or DVD
button on the remote to
enable DVD/CD playback.
Titles and chapters (DVD-VIDEO)
DVD-video is divided into several large sections called "titles" and smaller
•
sections called "chapters". Numbers are allotted to these sections.
These numbers are called "title numbers" and "chapter numbers".
Tracks (Video and music CDs)
Video and music CDs are divided into sections called "tracks".
•
Numbers are allotted to these sections. These numbers are called
"track numbers".
OPERATION
Buttons Enabled for TV Operation: POWER, CHANNEL, VOLUME, TV/VIDEO, and Numeric (0-9) buttons.
Note
•
By default, the remote control is set to work with Samsung TVs.
•
See page 63 for more information about remote control operation with other manufacturer's TVs.
17
Note
Files (DivX)
DivX is divided into sections called "files".
•
Numbers are allotted to these sections. These numbers are called
"file numbers".
In this manual, the instructions marked with "DVD ( )" are applicable
•
to DVD-VIDEO, DVD-AUDIO, and DVD-R/RW discs.
Where a particular DVD type is mentioned, it is indicated separately.
Depending on the content of the disc, the initial screen may appear different.
•
DVD
18
Disc Playback
Selecting a Disc in the Disc changer
The DVD/CD function is automatically selected when Disc Skip is pushed.
ENG
Press OPEN/CLOSE button to open the
1
disc tray.
Load a disc.
Place a disc gently into the tray with the disc’s label
•
2
3
4
facing up.
Press DISC SKIP button.
Rotate the carousel tray so you can load the third, fourth,
•
and fifth discs.
Close the compartment by pressing the
OPEN/CLOSE button again.
To select a specific disc, press the corresponding DIRECT PLAY(1, 2, 3, 4, 5) buttons on the front panel or DISC SKIP on the
remote control, until the required disc indicator flashes.
If the disc selected is not loaded, the next disc is played automatically.
•
To stop playback, press STOP during playback.
• If pressed once, “PRESS PLAY” is displayed and the stop position will be stored in memory.
If PLAY/PAUSE ( ) button or ENTER button is pressed, playback resumes from the stop position.
(This function works only with DVDs.)
• If pressed twice, “STOP” is displayed, and if PLAY/PAUSE ( ) button is pressed, playback starts from the
beginning.
OPERATION
Note
19
DVDVCDCD
Playback starts automatically.
•
Depending on the content of the disc, the initial screen may appear different.
•
To temporarily pause playback, press PLAY/PAUSE during playback.
To resume playback, press PLAY/PAUSE ( ) button again.
•
20
MP3/WMA-CD Playback
Something like you
Back for good
Love of my life
More than words
DVD RECEIVER SMART NAVI
Displaying Disc Information
ENG
Data CDs (CD-ROM, CD-R, CD-RW) encoded in MP3/WMA format can be played.
Press the
OPEN/CLOSE button
to open the disc tray,
1
and then load the
2
MP3/WMA disc.
The MP3/WMA menu screen will appear
•
and playback will start.
The appearance of the menu depends
•
on the MP3/WMA disc.
WMA-DRM files cannot be played.
•
•
To change the album,
use to
select another album
in Stop mode, and
3
then press the
4
ENTER button.
To select another album and track,
•
repeat Steps 2 and 3 above.
Depending on the recording mode, some MP3/WMA-CDs may not play.
Note
•
Table of contents of a MP3-CD varies depending on the MP3/WMA track
•
format recorded on the disc.
In Stop mode, use
to select
the album, and then
press the ENTER
button.
Use to select the track.
Press the STOP
button to stop
playback.
You can view disc playback information on the TV screen.
Press INFO button.
Each time the button is pressed, the display changes as follows:
•
DVD
The information Display
disappears from the screen
Note
Depending on the disc, the disc
•
information display may appear different.
Depending on the disc, you can also
•
select DTS, DOLBY DIGITAL, or PRO
LOGIC.
•
If this symbol appears on the TV screen while buttons are being operated,
that operation is not possible with the disc currently being played.
•
•
•
•
CDVCD
The information Display
disappears from the screen
appears on the TV screen!
What is a Group?
A section of tracks contained in a DVD-AUDIO disc.
What is a Title?
A movie contained in a DVD-VIDEO disc.
What is a Chapter?
Each title on a DVD disc is divided into several smaller sections called
"chapters".
What is a Track (File)?
A section of video or a music file recorded on a DVD-AUDIO, CD, or MP3-CD.
MP3DivXJPEG
The information Display
disappears from the screen
OPERATION
To play a file icon in the screen,
Press the button when it is in stop
status and select a desired icon from the top
part of the menu.
To play music files only, select the Icon.
•
To view image files only, select the Icon.
•
To view movie files only, select the Icon.
•
To select all files select the Icon.
•
Music File Icon
•
Image File Icon
•
Movie File Icon
•
All File Icon
•
Screen Display
DVD display
VCD display
CD display
DVD
DVD-AUDIO display
AUDIO
TITLE display
GROUP display
CHAPTER display
ELAPSED TIME display
REPEAT PLAYBACK display
AUDIO LANGUAGE display
TRACK (FILE) display
STEREO (L/R) display
DOLBY DIGITAL display
ANGLE display
SUBTITLE display
2221
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.