Samsung 910TM, 710TM, 913TM, 713BM User Manual
SyncMaster 710TM / 910TM / 713BM / 913TM
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited Important to read and understand at all times
Power
Do not disassemble Disconnect the plug from the outlet
Do not touch Grounding to prevent an electric shock
When not used for extended period of time, set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
z This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
z An improper ground may cause electric shock or equipmen t da mag e.
Insert the power plug firmly so that it does not come loose.
z A bad connection may cause fire.
Installation
Do not excessively bend the plug and wire nor place heavy objects upon
them, which could cause da mage.
z This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
z This may cause fire.
Be sure to contact an authorized Service Center when installing your set in a
location with heavy dust, high or low temperatures, high humidity, and
chemical substances, or where it will be operated for 24 hours continuously
such as an airport, train station or etc.
Failure to do so may cause serious damage to your set.
Put your monitor in a location with low humidity and a minimum of dust.
Failure to do so may cause an electric shock or fire inside the monitor.
z
Do not drop the monitor when moving it.
z This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the
base does not project beyond the showcase or shelf.
z Dropping the product may cause damage to the product or personal
injury.
Do not place the product on an unstable or small surface area.
z Place the product on an even, stable surface, as the product may fall
and cause harm to someone walking by, specifically children.
Do not place the product on the floor.
Someone, specifically children could trip over it.
z
Keep any flammable objects such as candles, insecticides or cigarettes
away from the product.
z Otherwise, this may cause a fire.
Keep any heating devices away from the power cable.
A melted coating may lead to electric shock or fire.
z
Do not install the product in places w i th poo r ve ntilation, for instance, a
bookshelf, closet, etc.
Any increase in internal temperature may cause fire.
z
Set down the monitor carefully.
The monitor could be damaged or broken.
z
Do not place the monitor face down.
z The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional.
Installation by unqualified personnel may result in injury.
z
z Always use the mounting device specified in the owner's manual .
When installing the product, make sure to keep it away from the wall
(more than 10cm/4inch ) for ventilation purposes.
z Poor ventilation may cause an increase in the internal temperature of
the product, resulting in a shortened component life and degraded
performance.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with
a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
z This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.
A dirty connector may cause an electric shock or fire.
z
Make sure to unplug the power cord before cleaning the product.
z Otherwise, this may cause electric shock or fire.
Others
Unplug the power cord from the power outlet and wipe the product using
a soft, dry cloth.
Do not use any chemicals such as wax, benzene, alcohol, thinners,
z
insecticide, air freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning
once a year.
z Keep the product's interior clean. Dust which has accumulated in the
interior over an extended period of time may cause malfunction or fire.
Do not remove cover (or back).
z This may cause an electric shock or fire.
z Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any
unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service.
z This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture;
do not install inside a vehicle.
z This may cause malfunction, an electric shock or fire.
z Especially avoid operating the monitor near water or outdoors where the
monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off
and unplug the power cord. Then contact the Service Center.
z The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is
not used for a long period of time.
Failure to do so may cause an electric shock or fire.
z
Do not try to move the monitor by pulling only the wire or the signal
cable.
This may cause a breakdown, electric shock or fire due to damage to
z
the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
z This may cause a breakdown, electric shock or fire due to damage to
the cable.
Do not cover the vents on the monitor cabinet.
z Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects
on the monitor.
z This may cause malfunction, an electric shock or fire.
If a foreign substance enters the monitor, unplug the power cord and
z
contact the Service Center .
Keep the product away from combustible chemical sprays or
inflammable substances.
z This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
z This may cause an electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and gimlet or
inflammable objects such as paper and match into the vent, headphone
port or AV ports.
z It may cause a fire or an electric shock. If an alien substances or water
flows into the product, turn the product off, unplug the power connector
from the wall outlet and contact Service Center.
If you view a fixed screen for an extended period of time, residua l ima ge
or blurriness may appear.
z Change the mode to energy save or set a screensaver to moving picture
when you need to be away from the monitor for an extended period of
time.
Adjust the resolution and frequency to the levels appropriate for the
model.
z Inappropriate resolution may cause undesirable picture quality.
17, 19 inch - 1280 X 1024
Keep the volume at a proper level when you use the headphones.
z Excessively loud volume levels may damage hearing.
Watching the monitor continuously at a too close angle may result in
eyesight damage.
To ease eye strain, take at least a five-minute break after every hour of
using the monitor
.
Do not install the product on an unstable, uneven surface or a location
prone to vibrations.
z Dropping the product may cause damage to the product or personal
injury. Using the product in a location prone to vibrations may shorte n
the lifetime of the product or may catch fire.
When moving the monitor, turn off and unplug the power cord.
Make sure that all cables, including the antenna cable and cables
connected to other devices, are disconnected before moving the
monitor.
z Failure to disconnect a cable may damage it and lead to fire or an
electric shock.
Place the product out of children's reach, as they could damage it by
hanging onto it.
z A falling product could cause physical damage even de ath.
When not using the product for an extended time period, keep the
product unplugged
z Otherwise, this may cause heat emission from the accumul ated dirt or
degraded insulation, leading to electric shock or fire.
Do not place children's favorite objects (or anything else that may be
tempting) on the product.
z Children may try to climb on the product to retrieve an object. The
product could fall, causing physical damage or even death.
r
p
g
A
)
Unpacking
SyncMaster 710TM
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local deale
to buy o
tional items.
Monitor ( Type (A)
Manual
Cable
Quick Setup Guide
D-Sub Cable Power Cord
Warranty Card
(Not available in all
locations)
Monitor ( Type (B) )
User's Guide,
Monitor Driver,
Natural Color software,
MagicTune™ software,
Ma
icRotation software
udio Cable
y
Sold separatel
DVI Cable
Front
Menu button [ ]
MagicBright button
[]
Opens the OSD menu. Also use to exit the OSD menu or return
to the previous menu.
MagicBright is a new feature providing optimum viewing
environment depending on the contents of the image you are
watching. Currently four different modes are available: Custom,
Text, Internet, and Entertain. Each mode has its own
preconfigured brightness value. You can easily select one of four
settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers,
the pre-configured values may not be comfortable to your
eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by
using the OSD menu.
2) Text
For documentations or works involving heavy text.
: Normal Brightness
3) Internet
For working with a mixture of images such as text and
graphics.
4) Entertain
For watching motion pictures such as a DVD or VCD.
>>Click here to see an animation clip
: Medium Brightness
: High Brightness
Volume button[ ]
Adjust buttons [ ]
Enter button [ ] /
Source button
Auto button
Power button
Power indicator
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed or wh en
leaving it unattended for long periods.
[]
When OSD is not on the screen, push the button to adjust
volume.
Adjust items in the menu.
Activates a highlighted menu item. /
Push the 'Source' and then select the Video signal while the
OSD is off. (When the Source button is pressed to change the
input mode, a message appears on the upper left of the screen
displaying the current mode -- analog or digital input signal.)
Note : If you select the Digital mode, you must connect your
monitor to the graphic card's port using the DVI cable.
Use this button for auto adjustment.
Use this button to turn the monitor on and off.
This light glows green during normal operation, and blinks green
once as the monitor saves your adjustments.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Power port
DVI port
D-sub 15-pin port
Power on/off Switch
Connect the power cord to the power port on the back of the monitor.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back
of your monitor.
Use this button for turn the monitor on and off.
Kensington Lock
The Kensington lock is a device used to physically fix the system
when using it in a public place. (The locking device has to be
purchased separately. )
Headphone connection
terminal
AUDIO IN
See Connecting the Monitor for further information regarding cable connections.
Connect the audio cable for your monitor to the audio port on the
back of your computer.
r
p
Unpacking
Type (A)
SyncMaster 713BM
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local deale
to buy optional items.
Type (B)
Manual
Monitor & Sim
Monitor & Pivot stand
le stand Bottom
g
A
p
y
Cable
Quick Setup Guide
Warranty Card
(Not available in all
locations)
User's Guide,
Monitor Driver,
Natural Color software,
MagicTune™ software,
Ma
icRotation software
D-Sub Cable Power Cord
Sold se
Front
aratel
DVI Cable
udio Cable
Menu button [ ]
MagicBright button
[]
Volume button[ ]
Adjust buttons [ ]
Opens the OSD menu. Also use to exit the OSD menu or return
to the previous menu.
MagicBright is a new feature providing optimum viewing
environment depending on the contents of the image you are
watching. Currently four different modes are available: Custom,
Text, Internet, and Entertain. Each mode has its own
preconfigured brightness value. You can easily select one of four
settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers,
the pre-configured values may not be comfortable to your
eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by
using the OSD menu.
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and
graphics.
4) Entertain
For watching motion pictures such as a DVD or VCD.
>>Click here to see an animation clip
When OSD is not on the screen, push the button to adjust
volume.
Adjust items in the menu.
: Normal Brightness
: Medium Brightness
: High Brightness
Enter button [ ] /
Source button
Auto button
Activates a highlighted menu item. /
Push the 'Source' and then select the Video signal while the
OSD is off. (When the Source button is pressed to change the
input mode, a message appears on the upper left of the screen
displaying the current mode -- analog or digital input signal.)
Note : If you select the Digital mode, you must connect your
monitor to the graphic card's port using the DVI cable.
Use this button for auto adjustment.
Power button
Power indicator
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed or wh en
leaving it unattended for long periods.
Rear
[]
Use this button to turn the monitor on and off.
This light glows green during normal operation, and blinks green
once as the monitor saves your adjustments.
(The configuration at the back of the monitor may vary from product to product.)
Power port
DVI port
D-sub 15-pin port
Power on/off Switch
Kensington Lock
Connect the power cord to the power port on the back of the monitor.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back
of your monitor.
Use this button for turn the monitor on and off.
The Kensington lock is a device used to physically fix the system
when using it in a public place. (The locking device has to be
purchased separately. )
Headphone connection
terminal
AUDIO IN
See Connecting the Monitor for further information regarding cable connections.
Connect the audio cable for your monitor to the audio port on the
back of your computer.
y
g
Unpacking
SyncMaster 910TM / 913TM
Please make sure the following items are included with your monitor.
If an
items are missing, contact your dealer.
Monitor
Manual
Cable
Quick Setup Guide
Warranty Card
(Not available in all
locations)
User's Guide,
Monitor Driver,
Natural Color software,
MagicTune™ software,
Ma
icRotataion software
A
y
Sold separatel
D-Sub Cable Power Cord
udio Cable
Front
DVI Cable
(option)
Menu button [ ]
MagicBright button
[]
Opens the OSD menu. Also use to exit the OSD menu or return
to the previous menu.
MagicBright is a new feature providing optimum viewing
environment depending on the contents of the image you are
watching. Currently four different modes are available: Custom,
Text, Internet, and Entertain. Each mode has its own
preconfigured brightness value. You can easily select one of four
settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers,
the pre-configured values may not be comfortable to your
eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by
using the OSD menu.
: Normal Brightness
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and
graphics.
4) Entertain
For watching motion pictures such as a DVD or VCD.
>>Click here to see an animation clip
: Medium Brightness
: High Brightness
Volume button[ ]
Adjust buttons [ ]
Enter button [ ] /
Source button
Auto button
Power button
Power indicator
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed or when
leaving it unattended for long periods.
[]
When OSD is not on the screen, push the button to adjust
volume.
Adjust items in the menu.
Activates a highlighted menu item. /
Push the 'Source' and then select the Video signal while the
OSD is off. (When the Source button is pressed to change the
input mode, a message appears on the upper left of the screen
displaying the current mode -- analog or digital input signal.)
Note : If you select the Digital mode, you must connect your
monitor to the graphic card's port using the DVI cable.
Use this button for auto adjustment.
Use this button to turn the monitor on and off.
This light glows green during normal operation, and blinks green
once as the monitor saves your adjustments.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Power port
DVI port
D-sub 15-pin port
Connect the power cord to the power port on the back of the monitor.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back
Power on/off Switch
Kensington Lock
of your monitor.
Use this button for turn the monitor on and off.
The Kensington lock is a device used to physically fix the system
when using it in a public place. (The locking device has to be
purchased separately. )
Headphone connection
terminal
AUDIO IN
See Connecting the Monitor for further information regarding cable connections.
Connect your headphone to the Headphone-out port.
Connect the audio cable for your monitor to the audio port on the
back of your computer.
SyncMaster 710TM
1.
2-1.
2-2.
2-3.
2-4.
3.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is
complete.
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor
B. Mounting interface pad
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion benea th it to protect th e
screen.
3. Remove four screws and then remove the Stand from the LCD monitor.
4. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure
it with four screws that came with the arm-type base, wall mount hanger or other base.
SyncMaster 713BM
1.
2-1.
2-2.
2-3.
2-4.
3.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is
complete.
Monitor Assembly
Monitor and Bottom
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Simple stand Pivot stand
A. Monitor
B. Mounting interface pad
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion benea th it to protect th e
screen.
3. Remove four screws and then remove the Stand from the LCD monitor.
4. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure
it with four screws that came with the arm-type base, wall mount hanger or other base.
SyncMaster 910TM / 913TM
1.
2-1.
2-2.
2-3.
2-4.
3.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is
complete.
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Loading...