Samsung 740T, 740N, 540N, 940N, 540B User Manual

Install drivers Install programs

SyncMaster 740B / 940B / 740N / 940Fn / 540B / 540N / 740T / 940T / 940N / 940Be

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Do not use a damaged or loose plug.

This may cause electric shock or fire.

z

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

z

Insert the power plug firmly so that it does not come loose.

z A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

z This may cause fire.

Do not disconnect the power cord while using the monitor.

A surge may be caused by the separation and may damage the monitor.

z

Do not use the power cord when the connector or plug is dusty.

z If the connector or plug of the power cord is dusty, clean it with a dry

cloth. Using the power cord with a dusty plug or connector may cause electric

z

shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

z Dropping the product may cause damage to the product or the person

carrying it.

Do not place the product on an unstable or small surface area.

z Place the product on an even, stable surface, as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

Take care, as someone, specifically children may trip over it.

z

Keep any flammable objects such as candles, insecticides or cigarettes away from the product.

Otherwise, this may cause fire.

z

Keep any heating devices away from the power cable.

A melted coating may cause electric shock or fire.

z

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

Any increase in internal temperature may cause fire.

z

Put down the monitor carefully.

Failing to do so may damage the monitor.

z

Do not place the monitor face down.

z This may damage the TFT-LCD surface.

The installation of the bracket must be done by a qualified professional.

Installing the bracket by unqualified personnel may result in injury.

z

z Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inchs) for ventilation purposes.

z Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded performance.

Clean

Keep the plastic packaging (bag) out of children's reach.

The plastic packaging (bag) may cause suffocation if children play with

z

it.

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

This may cause damage, electric shock or fire.

z

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

A dirty connector may cause electric shock or fire.

z

Make sure to unplug the power cord before cleaning the product.

Otherwise, this may cause electric shock or fire.

z

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

Do not use any chemicals such as wax, benzene, alcohol, thinners,

z

insecticide, air freshener, lubricant or detergent.

Other

Contact a Service Center or Customer Center for interior cleaning once a year.

Keep the product's interior clean. Dust which has accumulated in the

z

interior over an extended period of time may cause a malfunction or fire.

Do not remove the cover (or back).

This may cause electric shock or fire.

z

z Refer servicing to a qualified servicing company.

If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or Service Center.

z This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

z This may cause a malfunction, electric shock or fire.

In particular, avoid operating the monitor near water or outdoors where it

z

could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center.

z The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.

Failure to do so may cause electric shock or fire.

z

Do not try to move the monitor by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to

z

the cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

z

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause a malfunction, electric shock or fire.

z

z If a foreign substance enters the monitor, unplug the power cord and

contact a Service Center.

Keep the product away from combustible chemical sprays or inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports.

z This may cause electric shock or fire. If an alien substances or water

enters the product, turn the product off, unplug the power connector from the wall outlet and contact a Service Center.

When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.

z Change the mode to energy saving mode or set a screensaver to a

changing picture when away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z An inappropriate resolution may cause undesirable picture quality.

15 inch (38 cm) - 1024 X 768 17,19 inch (43, 48 cm) - 1280 X 1024

Viewing the monitor continuously at a too close angle may result in damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

z Dropping the product may cause damage to the product or the person

carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

Failure to disconnect cables may damage it and cause fire or an electric

z

shock.

Place the product out of children's reach, as they could damage it by hanging onto it.

A falling product may cause injury to the person or even fatality.

z

When not using the product for an extended period of time, keep the product unplugged.

Otherwise, this may cause heat emission from the accumulated dirt or

z

degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest on the product.

Children may try to climb on the product to retrieve an object. The

z

product could fall, causing physical damage or even death.

When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.

z This may cause your monitor to fall, and become damaged or cause

personal injury.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor.

Keep your back straight.

z

z Keep a distance of about 45 ~ 50 cm between your eyes and

the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.

z Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor

height so that the top of the monitor is slightly below eye level.

z Adjust the monitor angle so that there is no reflected light on

the screen.Try to maintain your arms perpendicular to your armpits.

z Keep your arms level with the back of your hands.

Keep the angle of the elbow perpendicular.

z

z Keep the angle of the knees at more than 90 degree. Do not let

your feet fall up from the floor. Adjust the arm position so that it is below the heart.

r

SyncMaster 740B / 940B

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Type 3

Monitor & Pivot stand

Type 4

g

)

Manual

Monitor & Sliding Stand

Monitor & Lowest HAS Stand

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

Cable

Front

D-sub Cable Power Cord DVI Cable (option

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ] / Source button

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.

AUTO button

(op

)

Use this button for auto adjustment.

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

Simple stand Pivot stand / Sliding Stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

DVI IN port

RGB IN port

POWER on/off Switch

tion

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. Use this button for turn the monitor on and off.

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

SyncMaster 540B

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Manual

Monitor & Pivot stand

g

Cable

)

Front

User's Guide,

Warranty Card

Quick Setup Guide

D-sub Cable Power Cord DVI Cable (option

(Not available in all

locations)

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers,

the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ] / Source button

AUTO button

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.

Use this button for auto adjustment.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

Simple stand Pivot stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

DVI IN port

RGB IN port

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

SyncMaster 740N / 940N

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Type 3

Monitor & Pivot stand

Type 4

g

Manual

Monitor & Sliding Stand

Monitor & Lowest HAS Stand

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

Cable

Front

D-sub Cable Power Cord

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ]

AUTO button

Power button [ ]/ Power indicator

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item.

Use this button for auto adjustment.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving

(op

)

functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

Simple stand Pivot stand / Sliding Stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

RGB IN port

POWER on/off Switch

tion

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. Use this button for turn the monitor on and off.

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

SyncMaster 540N

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Manual

Monitor & Pivot stand

g

Cable

Front

Warranty Card

Quick Setup Guide

D-sub Cable Power Cord

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers,

the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ]

AUTO button

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item.

Use this button for auto adjustment.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

Simple stand Pivot stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

Connect the power cord for your monitor to the power port on the back

of the monitor.

RGB IN port

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

g

SyncMaster 940Fn

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Manual

Monitor & Pivot stand

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

Cable

'DVI-A to D-sub' Cable Power Cord DVI Cable

Front

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Enter button [ ] /

(op

)

Source button

AUTO button

Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.

Use this button for auto adjustment.

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

(The configuration at the back of the monitor may vary from product to product.)

POWER port

DVI IN port

RGB IN port

Power on/off Switch

tion

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI Port on the back of your Monitor.

Connect the 'DVI-A to D-SUB' Cable to the RGB IN port on the back of your monitor. Use this button for turn the monitor on and off.

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

SyncMaster 740T / 940T

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Type 3

Monitor & Sliding Stand

Manual

g

)

Cable

Monitor & Lowest HAS Stand

User's Guide,

Warranty Card

Quick Setup Guide

D-sub Cable Power Cord DVI Cable (option

(Not available in all

locations)

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

Front

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ] / Source button

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.

AUTO button

(op

)

Use this button for auto adjustment.

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

Simple stand Sliding Stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

DVI IN port

RGB IN port

POWER on/off Switch

tion

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. Use this button for turn the monitor on and off.

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

r

SyncMaster 940Be

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to buy optional items.

Unpacking

Type 1

Type 2

Monitor & Simple stand Bottom

MagicRotation program can not be provided as Simple Stand does not support Pivot function.

Manual

Monitor & Sliding Stand

g

Cable

)

Front

User's Guide,

Warranty Card

Quick Setup Guide

D-sub Cable Power Cord DVI Cable (option

(Not available in all

locations)

Monitor Driver,

Natural Color software,

MagicTune™ software

Ma

icRotation software

MENU button [ ]

MagicBright™™ []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.

1) Custom

Although the values are carefully chosen by our engineers,

the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.

2) Text

For documentations or work involving a lot of text.

3) Internet

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

Brightness button []

Adjust buttons [ ]

Enter button [ ] / Source button

AUTO button

Power button [ ]/ Power indicator

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

When OSD is not on the screen, push the button to adjust brightness.

Adjust items in the menu.

Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.

Use this button for auto adjustment.

Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.

Rear

Simple stand Sliding Stand

(op

)

(The configuration at the back of the monitor may vary from product to product.)

POWER port

DVI IN port

RGB IN port

POWER on/off Switch

tion

Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. Use this button for turn the monitor on and off.

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

SyncMaster 740B / 940B / 540B / 740T / 940T / 940Be

Connecting the Monitor

1.

2-1.

2-2.

2-3.

2-4.

3.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

[ RGB IN ]

Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor.

[ DVI IN ]

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable.

In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Using the Stand

y

Monitor Assembl

Monitor and Bottom

Pivot Stand / Sliding Stand

Stand Stopper

A.

Attaching a Base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Pivot stand

Simple stand

Monitor

A.

Mounting interface pad (Sold separately)

B.

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Sliding Stand

Lowest HAS Stand

Connecting the Monitor

SyncMaster 740N

1.

2-1.

2-2.

2-3.

3.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable.

In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Using the Stand

[ RGB IN ]

Monitor Assembl

y

Monitor and Bottom

Swivel stand

Pivot Stand / Sliding Stand

Stand Stopper

A.

Attaching a Base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Pivot stand

Simple stand

Monitor

A.

Sliding Stand

Lowest HAS Stand

Mounting interface pad (Sold separately)

B.

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Connecting the Monitor

SyncMaster 940Fn

1.

2-1.

2-2.

2-3.

2-4.

3.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card. Connect the 'DVI-A to D-SUB' Cable to the RGB IN port on the back of your monitor.

[ RGB IN ]

Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI IN port on the back of your monitor.

[ DVI IN ]

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the 'DVI-A to D-SUB' connection cable.

In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Using the Stand

Pivot Stand

Stand Stopper

A.

Attaching a Base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Monitor

A.

Mounting interface pad (Sold separately)

B.

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Connecting the Monitor

SyncMaster 540N / 940N

1.

2-1.

2-2.

2-3.

3.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable.

In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Using the Stand

[ RGB IN ]

Monitor Assembl

y

Monitor and Bottom

Pivot Stand

Stand Stopper

A.

Attaching a Base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Simple stand Pivot stand

Monitor

A.

Mounting interface pad (Sold separately)

B.

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

1. Insert CD into the CD-ROM drive.

2. Click

"Windows"

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. If you can see following message window, then click the Then click

button. (Microsoft

"OK"

®

Windows® XP Operating System)

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor homepage

http://www.samsung.com/.

5. Monitor driver installation is completed.

"Continue Anyway"

button.

Installing the Monitor Driver (Manual)

Windows XP | Windows 2000 |Windows Me |Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" —> "

Control Panel

" then click the "

Appearance and Themes

" Icon.

3. Click "

4. Click the "

Display

" icon and choose the "

Properties

" button on the "

Settings

Monitor

" tab then click "

" tab and select "

Advanced..

Driver

".

" tab.

5. Click "

6. Select "

Update Driver..

Don't search ,I will..

" and select "

Install from a list or..

" then click "

" and then click "

Have disk

".

7. Click the " model list and click the "

8. If you can see following " click "OK" button.

Browse

" button then choose A:(D:\Driver) and choose your monitor model in the

" button.

" window, then click the "

Continue Anyway

" button. Then

This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/

9. Click the "

" button then click "OK" button continually.

Close

10. Monitor driver installation is completed.

Microsoft® Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Case1: If the "Properties" button is inactive, it means your monitor is properly configured.

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps

5. Click "

6. Choose "

specific driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

Browse

Start

Monitor

Please stop installation

continually.

Driver

Display a list of the known drivers for this device so that I can choose a

Browse Open

Finish

" button on the "

" , "

Setting

Display

Settings

".

" and then click on "

" then click "

" button then choose A:(D:\Driver).

" button, then click "OK" button.

" button then the "

Insert disk

" , "

Control Panel

" Icon.

" tab and then click "

File Needed

Update Driver..

" and then click "

Close

" window.

".

Advanced..

" button then click "

".

" then click on the "Next" button.

Have disk

".

If you can see the " And click the "

Microsoft® Windows® Millennium Operating System

1. Click "

2. Double click "

3. Select the "

4. Select the "

5. Click the "

6. Choose "

7. Choose "

8. Click the "

9. Specify A:\(D:\driver) then click "OK" button.

10. Select " connected to your computer and click "OK".

11. Continue choosing " dialogue box.

Microsoft® Windows® NT Operating System

1. Click

2. In Display Registration Information window, click Settings Tab and then click

Modes

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.

4. Click

" , "

Start

Settings Monitor

Change Specify the location of the driver Display a list of all the driver in a specific location..

Have Disk

Show all devices

Start,Settings,Control Panel

.

Apply

Digital Signature Not Found

" button then the "

Finish

Setting

Display

button if you see the screen working normally after clicking

" , "

Control Panel

" icon.

" tab and click "

" tab.

" button in the "

" button

" and choose the monitor that corresponds to the one you

" button and "OK" button until you close the Display Properties

Close

".

Advanced Properties

Monitor Type

, and then double-click

" window then click the "

" button.

" area.

".

Display

Yes

" then click "

icon.

Test

"button.

" button.

. If the screen is

not normal, change to a different mode (lower mode of resolution, colors or frequency).

r

If there is no Mode at frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for

3. Set a mouse for your computer.

4. The next screen is for

5. Set a Keyboard for your computer.

6. The next screen is for

7. First of all, set a directly.)

8. Set a

9. Enter the

10. You have

vertical frequency

of X-Window.

Execute

X-Window after setting other requested hardware.

horizontal frequency

model name of your monitor

finished

setting up your monitor.

All Display Modes

setting your mouse

selecting a keyboard

setting your monitor

for your monitor. (You can enter the frequency

for your monitor. (You can enter the frequency directly.)

. This information will not affect the actual execution

, select the level of resolution and vertical

.

Natural Color

Natural Colo

One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This is only available for Samsung monitors and ensures that the color of the images on the monitor are the same as the printed or scanned images. For more information, refer to Help (F1) in the software program.

Installing the Natural Color Software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural Color screen will appear. Click on Natural Color in the startup window to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-

ROM Drive, click the Windows [Start] button, select [Run...]. Enter D:\color\NCProsetup.exe and then press the <Enter> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.)

Uninstalling the Natural Color Software Program

Select

"Setting/Control Panel"

program"

Select Natural Color from the list and then click the

.

on the

menu and then double-click

"Start"

"Add/Delete"

button.

"Add/Delete a

SyncMaster 740B / 940B

1.

[ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu.

[ ]This button allows you to adjust items in the menu.

2.

[ ]Press this button to Activates a highlighted menu item.

3.

4.[AUTO

]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and

position are adjusted automatically.

AUTO

Menu Description

AUTO

Locked

When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.

- If you change resolution in the control panel, auto function will be executed automatically.

' button is pressed, the Auto Adjustment screen appears

AUTO

Menu Description

After pushing the "MENU" button more than 5 seconds, OSD function is

Locked

locked (unlocked).

You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature.

MagicBright™

Menu Description

Push the MagicBright button to circle through available preconfigured

MagicBright™

modes.

- Six different modes (Custom/Text/Internet/Game/Sport/Movie)

Brightness

Menu Description

Brightness

SOURCE

When OSD is not on the screen, push the button to adjust brightness.

Menu Description

SOURCE

Selects the video signal while the OSD is off.

Picture

Color

Image

OSD

Setup

Information

Picture

Brightness Contrast

MagicColor Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Auto Source Image Reset Color Reset

Menu Description Play/Stop

You can use the on-screen menus to change the brightness according to personal preference.

Brightness

Contrast

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.)

: When OSD is not on the screen,

Color

Menu Description Play/Stop

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

- Returns to the original mode.

1) Off

2) Demo

appears on the right and the screen after applying MagicColor appears on the left.

3) Full

more realistic natural skin color with clearness.

4) Intelligent

5) MagicZone

sharp display of animated multimedia or photo images by enhancing the brightness, sharpness, saturation, hue of a certain area on the screen. Especially, MagicZone is appropriate to using the moving picture.

- The screen before applying MagicColor

- Displays not only vivid natural color but also

- Displays vivid natural color with clearness.

- The MagicZone ensures the clear and MagicZone

MagicColor

Hue

: This function is to adjust the hue of the MagicZone.

Saturation : This function is to adjust the saturation of the MagicZone.

Brightness : This function is to adjust the brightness of the MagicZone.

Sharpness : This function is to adjust the sharpness of the MagicZone.

H-Position : This function is to move the MagicZone horizontally.

V-Position : This function is to move the MagicZone vertically.

H-Size : This function is to adjust the horizontal size of the MagicZone.

V-Size

Hue

Saturation

Brightness

Sharpness

H-Position

V-Position

H-Size

V-Size

Color Tone

: This function is to adjust the vertical size of the MagicZone.

The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.)

Color Control

Gamma

Image

Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.)

Gamma correction changes the luminance of the colors with intermediate luminance.

z

Mode 1

z

Mode 2

z

Mode 3

Menu Description Play/Stop

Removes noise such as vertical stripes. Coarse

Coarse

adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only)

Removes noise such as horizontal stripes. If the noise

Fine

persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only)

Sharpness

Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.)

Changes the horizontal position of the monitor's entire

H-Position

display. (Available in analog mode only)

Changes the vertical position of the monitor's entire

V-Position

OSD

display. (Available in analog mode only)

Menu Description Play/Stop

You can choose one of 9 languages.

Language

:The language chosen affects only the language of

Note

the OSD. It has no effect on any software running on the computer.

H-Position

V-Position

Transparency

Display Time

You can change the horizontal position where the OSD menu appears on your monitor.

You can change the vertical position where the OSD menu appears on your monitor.

Change the transparency of the background of the OSD.

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.

Setup

Menu Description Play/Stop

Auto Source

Image Reset

Color Reset

Information

Select

Auto Source

the signal source.

Image parameters are replaced with the factory default values.

Color parameters are replaced with the factory default values.

for the monitor to automatically select

Menu Description

Information

Shows a video source, display mode on the OSD screen.

SyncMaster 740N / 940N

1.

[ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu.

[ ]This button allows you to adjust items in the menu.

2.

[ ]Press this button to Activates a highlighted menu item.

3.

4.[AUTO

]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and

position are adjusted automatically.

AUTO

Menu Description

AUTO

Locked

When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.

- If you change resolution in the control panel, auto function will be executed automatically.

' button is pressed, the Auto Adjustment screen appears

AUTO

Menu Description

After pushing the "MENU" button more than 5 seconds, OSD function is

Locked

locked (unlocked).

You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature.

MagicBright™

Menu Description

Push the MagicBright button to circle through available preconfigured

MagicBright™

modes.

- Six different modes (Custom/Text/Internet/Game/Sport/Movie)

Brightness

Menu Description

Brightness

Picture

Color

Image

OSD

Setup

Information

Picture

When OSD is not on the screen, push the button to adjust brightness.

Brightness Contrast

MagicColor Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Image Reset Color Reset

Menu Description Play/Stop

You can use the on-screen menus to change the brightness according to personal preference.

Brightness

Contrast

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.)

: When OSD is not on the screen,

Color

Menu Description Play/Stop

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

- Returns to the original mode.

1) Off

2) Demo

- The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.

- Displays not only vivid natural color but also

3) Full

more realistic natural skin color with clearness.

4) Intelligent

5) MagicZone

sharp display of animated multimedia or photo images by

- Displays vivid natural color with clearness.

- The MagicZone ensures the clear and MagicZone

enhancing the brightness, sharpness, saturation, hue of a certain area on the screen. Especially, MagicZone is appropriate to using the moving picture.

MagicColor

Color Tone

Hue

: This function is to adjust the hue of the MagicZone.

Saturation : This function is to adjust the saturation of the MagicZone.

Brightness : This function is to adjust the brightness of the MagicZone.

Sharpness : This function is to adjust the sharpness of the MagicZone.

H-Position : This function is to move the MagicZone horizontally.

V-Position : This function is to move the MagicZone vertically.

H-Size : This function is to adjust the horizontal size of the MagicZone.

V-Size : This function is to adjust the vertical size of the MagicZone.

The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.)

Hue

Saturation

Brightness

Sharpness

H-Position

V-Position

H-Size

V-Size

Color Control

Gamma

Image

Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.)

Gamma correction changes the luminance of the colors with intermediate luminance.

z

Mode 1

z

Mode 2

z

Mode 3

Menu Description Play/Stop

Removes noise such as vertical stripes. Coarse

Coarse

Fine

adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only)

Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only)

Sharpness

H-Position

V-Position

OSD

Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.)

Changes the horizontal position of the monitor's entire display. (Available in analog mode only)

Changes the vertical position of the monitor's entire display. (Available in analog mode only)

Menu Description Play/Stop

You can choose one of 9 languages.

Language

:The language chosen affects only the language of

Note

the OSD. It has no effect on any software running on the computer.

H-Position

V-Position

Transparency

Display Time

Setup

You can change the horizontal position where the OSD menu appears on your monitor.

You can change the vertical position where the OSD menu appears on your monitor.

Change the transparency of the background of the OSD.

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.

Menu Description Play/Stop

Image Reset

Color Reset

Information

Image parameters are replaced with the factory default values.

Color parameters are replaced with the factory default values.

Menu Description

Information

Shows a video source, display mode on the OSD screen.

SyncMaster 940Fn

1.

[ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu.

[ ]This button allows you to adjust items in the menu.

2.

[ ]Press this button to Activates a highlighted menu item.

3.

4.[AUTO

]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and

position are adjusted automatically.

AUTO

Menu Description

AUTO

Locked

When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.

- If you change resolution in the control panel, auto function will be executed automatically.

' button is pressed, the Auto Adjustment screen appears

AUTO

Menu Description

After pushing the "MENU" button more than 5 seconds, OSD function is

Locked

locked (unlocked).

You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature.

MagicBright™

Menu Description

Push the MagicBright button to circle through available preconfigured

MagicBright™

modes.

- Six different modes (Custom/Text/Internet/Game/Sport/Movie)

Brightness

Menu Description

Brightness

SOURCE

When OSD is not on the screen, push the button to adjust brightness.

Menu Description

SOURCE

Selects the video signal while the OSD is off.

Picture

Color

Image

OSD

Setup

Information

Picture

Brightness Contrast

MagicColor Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Auto Source Image Reset Color Reset Priority

Menu Description Play/Stop

You can use the on-screen menus to change the brightness according to personal preference.

Brightness

Contrast

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.)

: When OSD is not on the screen,

Color

Menu Description Play/Stop

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

- Returns to the original mode.

1) Off

2) Demo

appears on the right and the screen after applying MagicColor appears on the left.

3) Full

more realistic natural skin color with clearness.

4) Intelligent

5) MagicZone

sharp display of animated multimedia or photo images by enhancing the brightness, sharpness, saturation, hue of a certain area on the screen. Especially, MagicZone is appropriate to using the moving picture.

- The screen before applying MagicColor

- Displays not only vivid natural color but also

- Displays vivid natural color with clearness.

- The MagicZone ensures the clear and MagicZone

MagicColor

Hue

: This function is to adjust the hue of the MagicZone.

Saturation : This function is to adjust the saturation of the MagicZone.

Brightness : This function is to adjust the brightness of the MagicZone.

Sharpness : This function is to adjust the sharpness of the MagicZone.

H-Position : This function is to move the MagicZone horizontally.

V-Position : This function is to move the MagicZone vertically.

H-Size : This function is to adjust the horizontal size of the MagicZone.

V-Size

Hue

Saturation

Brightness

Sharpness

H-Position

V-Position

H-Size

V-Size

Color Tone

: This function is to adjust the vertical size of the MagicZone.

The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.)

Color Control

Gamma

Image

Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.)

Gamma correction changes the luminance of the colors with intermediate luminance.

z

Mode 1

z

Mode 2

z

Mode 3

Menu Description Play/Stop

Removes noise such as vertical stripes. Coarse

Coarse

adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only)

Removes noise such as horizontal stripes. If the noise

Fine

persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only)

Sharpness

Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.)

Changes the horizontal position of the monitor's entire

H-Position

display. (Available in analog mode only)

Changes the vertical position of the monitor's entire

V-Position

OSD

display. (Available in analog mode only)

Menu Description Play/Stop

You can choose one of eight languages.

Language

:The language chosen affects only the language of

Note

the OSD. It has no effect on any software running on the computer.

H-Position

V-Position

Transparency

Display Time

You can change the horizontal position where the OSD menu appears on your monitor.

You can change the vertical position where the OSD menu appears on your monitor.

Change the transparency of the background of the OSD.

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.

Setup

Menu Description Play/Stop

Auto Source

Image Reset

Color Reset

Priority

Information

Select

Auto Source

the signal source.

Image parameters are replaced with the factory default values.

Color parameters are replaced with the factory default values.

This is a source-switch function according to the priority that the user has set for the source.

for the monitor to automatically select

Menu Description

Information

Shows a video source, display mode on the OSD screen.

SyncMaster 540B / 740T / 940T / 940Be

1.

[ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu.

[ ]This button allows you to adjust items in the menu.

2.

[ ]Press this button to Activates a highlighted menu item.

3.

4.[AUTO

]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and

position are adjusted automatically.

AUTO

Menu Description

AUTO

Locked

When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.

- If you change resolution in the control panel, auto function will be executed automatically.

' button is pressed, the Auto Adjustment screen appears

AUTO

Menu Description

After pushing the "MENU" button more than 5 seconds, OSD function is

Locked

locked (unlocked).

You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature.

MagicBright™

Menu Description

Push the MagicBright button to circle through available preconfigured

MagicBright™

modes.

- Six different modes (Custom/Text/Internet/Game/Sport/Movie)

Brightness

Menu Description

Brightness

SOURCE

When OSD is not on the screen, push the button to adjust brightness.

Menu Description

SOURCE

Selects the video signal while the OSD is off.

Picture

Color

Image

OSD

Setup

Information

Picture

Brightness Contrast

MagicColor Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Auto Source Image Reset Color Reset

Menu Description Play/Stop

You can use the on-screen menus to change the brightness according to personal preference.

Brightness

Contrast

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.)

: When OSD is not on the screen,

Color

Menu Description Play/Stop

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

- Returns to the original mode.

1) Off

2) Demo

appears on the right and the screen after applying MagicColor appears on the left.

3) Full

more realistic natural skin color with clearness.

4) Intelligent

5) MagicZone

sharp display of animated multimedia or photo images by enhancing the brightness, sharpness, saturation, hue of a certain area on the screen. Especially, MagicZone is appropriate to using the moving picture.

- The screen before applying MagicColor

- Displays not only vivid natural color but also

- Displays vivid natural color with clearness.

- The MagicZone ensures the clear and MagicZone

MagicColor

Hue

: This function is to adjust the hue of the MagicZone.

Saturation : This function is to adjust the saturation of the MagicZone.

Brightness : This function is to adjust the brightness of the MagicZone.

Sharpness : This function is to adjust the sharpness of the MagicZone.

H-Position : This function is to move the MagicZone horizontally.

V-Position : This function is to move the MagicZone vertically.

H-Size : This function is to adjust the horizontal size of the MagicZone.

V-Size

Hue

Saturation

Brightness

Sharpness

H-Position

V-Position

H-Size

V-Size

Color Tone

: This function is to adjust the vertical size of the MagicZone.

The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.)

Color Control

Gamma

Image

Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.)

Gamma correction changes the luminance of the colors with intermediate luminance.

z

Mode 1

z

Mode 2

z

Mode 3

Menu Description Play/Stop

Removes noise such as vertical stripes. Coarse

Coarse

adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only)

Removes noise such as horizontal stripes. If the noise

Fine

persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only)

Sharpness

Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.)

Changes the horizontal position of the monitor's entire

H-Position

display. (Available in analog mode only)

Changes the vertical position of the monitor's entire

V-Position

OSD

display. (Available in analog mode only)

Menu Description Play/Stop

You can choose one of eight languages.

Language

:The language chosen affects only the language of

Note

the OSD. It has no effect on any software running on the computer.

H-Position

V-Position

Transparency

Display Time

You can change the horizontal position where the OSD menu appears on your monitor.

You can change the vertical position where the OSD menu appears on your monitor.

Change the transparency of the background of the OSD.

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.

Setup

Menu Description Play/Stop

Auto Source

Image Reset

Color Reset

Information

Select

Auto Source

the signal source.

Image parameters are replaced with the factory default values.

Color parameters are replaced with the factory default values.

for the monitor to automatically select

Menu Description

Information

Shows a video source, display mode on the OSD screen.

SyncMaster 540N

1.

[ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu.

[ ]This button allows you to adjust items in the menu.

2.

[ ]Press this button to Activates a highlighted menu item.

3.

4.[AUTO

]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and

position are adjusted automatically.

AUTO

Menu Description

AUTO

Locked

When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)

To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.

- If you change resolution in the control panel, auto function will be executed automatically.

' button is pressed, the Auto Adjustment screen appears

AUTO

Menu Description

After pushing the "MENU" button more than 5 seconds, OSD function is

Locked

locked (unlocked).

You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature.

MagicBright™

Menu Description

Push the MagicBright button to circle through available preconfigured

MagicBright™

modes.

- Six different modes (Custom/Text/Internet/Game/Sport/Movie)

Brightness

Menu Description

Brightness

Picture

Color

Image

OSD

Setup

Information

Picture

When OSD is not on the screen, push the button to adjust brightness.

Brightness Contrast

MagicColor Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Image Reset Color Reset

Menu Description Play/Stop

You can use the on-screen menus to change the brightness according to personal preference.

Brightness

Contrast

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.)

: When OSD is not on the screen,

Color