Samsung 730MP User Manual

g

Install Drivers Install Pro

rams

Power

Failure to follow directions noted by this symbol could re sult in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z This may cause fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

z The monitor may cause injury by falling.

Set down the monitor carefully.

z The monitor could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

z Installation by unqualified personnel may result in injury. z Always use the mounting device specified in the owner's manual.

Leave a space for ventilation between the product and the wall.

z Poor ventilation may cause the interior temperature to rise and lead to fire.

To prevent rainwater from running along the outdoor antenna cable and entering the house, be sure the outdoor portion of the cable hangs down below the point of entry.

z If rainwater enters the product, it may cause an electric shock or fire.

If you are using an outdoor antenna, be sure to put sufficient distance between your antenna and the electrical wires nearby so that they would not come in contact with each other in case the antenna is knocked over by strong wind.

z A knocked-over antenna may cause injury or an electric shock.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

z A dirty connector may cause an electric shock or fire.

Contact a Service Center or Customer Center for interior cleaning once a year.

z Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or fire.

Others

Do not remove cover (or back). No user serviceable parts inside.

z This may cause an electric shock or fire. z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact

an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to moisture.

z

This may cause malfunction, an electric shock or fire.

z Especially avoid operating the monitor near water or outdoors where it could be

exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord.

z The monitor may malfunction, causing an electric shock or fire.

z

Then contact the Servic e Center .

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause malfunction, an electric shock or fire. z If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center .

Do not use or store inflammable substances near the monitor.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause an electric shock, fire or injury.

Do not insert metal objects such as utensils, wire or drill bits, or th ings that catch fire easily, such as pieces of paper or matches, into the vents, or the headphone, or A/V ports on the monitor.

z This may cause malfunction, an electric shock or fire. z Always contact the Service Center if foreign substances/objects enter into the

monitor.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

z Change the mode to energy sav e or set a screensaver to moving picture when

you need to be away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

17 inch - 1280 X 1024

Keep the volume at a proper level when you use the headphones.

z Excessively loud volume levels may damage hea ring.

Keep a proper distance between your eyes and the monitor screen.

z Sitting too close to the monitor on a continuous basis may d a mage eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

.

Do not use the monitor where it may be exposed to strong vibrations.

z Exposure to strong vibrations may be fire hazard and shorten the life of the

monitor.

When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor.

z Failure to disconnect a cable may damage it and lead to fire o r an electric

shock.

When you remove batteries from the remote, be care ful that they are not swallowed by children. Keep batteries out of the reach of children.

z If swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position as indicated on battery holder.

z Incorrect polarity may cause a battery to break or leak and could lead to fire,

injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries together.

z This may cause a battery to break or leak and could lead to fire, injury, or

contamination (damage).

Do not set a glass of water, chemicals or any small metal objects on the monitor.

z This may cause damage, electric shock or fire. z If a foreign substance gets into the monitor, disconnect the plug and then

contact a service center.

r

(

)

(Op

)

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer

Contact a local deale

.

to buy optional items.

Unpacking

Manual

Quick Setup Guide

Option A

Monitor

Warranty Card

Not available in all locations

Option B

Monitor & WISELINK

User's Guide, Monitor Driver,

Natural Color software

Cable

tion A

D-Sub Cable Power Cord Radio Antenna

p

y

r

(Op

)

p

y

r

D-Sub Cable Power Cord Radio Antenna

Audio Cable

Option B

USB Cable

Cable

Sold se

tion B

aratel

D-Sub Cable Power Cord Radio Antenna

DVI Cable

Others

Audio Cable

USB Cable

Sold se

aratel

DVI Cable

Remote Control Batteries (AAA X 2) Connecte

Others

Option B

WISELINK

Front

Remote Control Batteries (AAA X 2) Connecte

1. MENU

2. CH

3. + VOL -

4. ENTER/FM RADIO

5. SOURCE

1. MENU

6. PIP

2. CH

7. Power button

3. - VOL +

8. Power indicator

4. ENTER/FM RADIO

5. SOURCE

9. Remote Control Sensor

6. PIP

7. Power button

8. Power indicator

9. Remote Control Sensor

1. MENU

Use this button for open the on -screen menu and exits from the menu screen or closes

Use this button for open the on-screen menu and exits from the menu screen or closes

screen adjustment menu.

2. CH

Moves from one menu item to another vertically or adjusts sele cted menu values. In TV

Moves from one menu item to another vertically or adjusts selected menu values. In TV

mode, selects TV channels.

>>Click here to see an animation clip

3. + VOL -

3. - VOL +

Moves from one menu item to another horizontally or adjusts selected menu values. Also

Moves from one menu item to another horizontally or adjusts selected menu values. Also adjusts the audio volume.

adjusts the audio volume.

>>Click here to see an animation clip

4. ENTER / FM RADIO

ENTER

ENTER FM RADIO

FM RADIO

In PC/DVI mode, sets only SOUND to FM Radio.

In areas where signal is weak, noise may occur while FM radio is broadcast.

In general VIDEO SOURC E mode, sets to FM RADIO, turning off the screen.

In general VIDEO SOURCE mode, sets to FM RADIO, turning off the screen.

>>Click here to see an animation clip

5. SOURCE

Switches from PC mode to Video mode.

Changing the source is allowed only external devices that are connected to the monitor at

the time.

the time. To switch Screen modes:

To switch Screen modes: [PC] [DVI] [TV] [Ext.] [AV] [S-VIDEO] [Component]

[PC] [DVI] [TV] [Ext.] [AV] [S-VIDEO] [Component]

>>Click here to see an animation clip

NOTE : According to broadcasting type in each country, you may not be able to select one.

Scart is mainly used in Europe.

For more information > Broadcasting Systems

6. PIP ( Available in PC/DVI Mode O nly )

6. PIP ( Available in PC/DVI Mode Only )

In PC Mode, turns on Video or TV screens in PIP Mode.

>>Click here to see an animation clip

7. Power button

Use this button to turn the monitor on and off.

8. Power indicator

Power Indicator shows PowerSaver mode by green blinking.

9. Remote Control Sensor

Aim the remote control towards this spot on the Monitor.

See PowerSaver described in the manual for further information regarding power saving functions.

For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended

for long periods.

: Activates a highlighted menu item.

: Turns on/off FM Radio.

Rear

(The configuration at the back of the monitor may vary from product to product.)

1. DC Power Connection Terminal

1. Power Connection Terminal

This product may be used with 90 ~ 264VAC.

2. PC connection terminal

3. FM RADIO / TV connection terminal

3. COMPONENT terminal

4. FM RADIO / TV connection terminal

4. EXT(RGB) connection terminal

z

Computer connection terminal (DVI(HDCP))

z

z Computer connection terminal (1 5 Pin D-SUB)

z Computer connection terminal(15 Pin D-SUB)

Audio connection terminal

z

z FM RADIO ANT connection terminal

z DVD/DTV left / right audio connection terminal (R/L)

DVD/DTV Component(PR, PB,Y) terminal

z

z TV connection terminal

For more information > Connecting TV

z Headphone connection terminal (Output)

TV connection terminal

z

For more information > Connecting TV FM RADIO ANT connection terminal

z z Headphone connection terminal (Output)

EXT(RGB) connection terminal

5. AV connection terminal

5. EXT(RGB) connection terminal

- Scart is mainly used in Europe.

EXT(RGB) connection terminal

z

S-Video connection terminal (Input)

- Scart is mainly used in Europe.

z Video connection terminal (Input) z Left(L) / Right(R) audio connection terminal (Input)

6. AV connection terminal

See Connecting the Monitor for further information regarding cable connections.

Remote Control

Left(L) / Right(R) AUDIO connection terminal (Input)

z

VIDEO connection terminal (Input)

z

S-VIDEO connection terminal (Input)

z

1. POWER

2. CHANNEL

3. +100, -/--

4. - +

5. MUTE

6. TTX/MIX

7. MENU

8. ENTER

9. FM RADIO

10. CH/P

11. SOURCE

12. INFO

1. POWER

13. EXIT

2. CHANNEL

14. Up-Down Left-Right Buttons

3. +100, -/--

15. AUTO

4. - +

16. P.MODE, M/B (MagicBright™)

17. P.SIZE

A

5. MUTE

18. STILL

6. TTX/MIX

7. MENU

19. PIP

20. S.MODE

8. ENTER

21. DUAL/MTS

9. FM RADIO

22. PRE-CH

10. CH/P

23. SOURCE

11. SOURCE

24. SIZE

12. INFO

25. POSITION

13. EXIT

14. Up-Down Left-Right Buttons

26. MAGIC-CH

1. POWER

Use this button to turn the monitor on and off.

2. CHANNEL

Selects TV channels in the TV mode. You may use this butt on in PIP mode as well.

3. +100

Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1".

-/-- (One/Two-Digit channel selectio n )

Use to select a channel nu mbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number.

4. - +

djusts the audio volume.

1. POWER

5. MUTE

Use this button to turn the monitor on and off.

Pauses (mutes) the audio output temporarily. Displays on the lower left corner of the screen.

2. CHANNEL

The audio resumes if Mute or - + is pressed in the Mute mode.

Selects TV channels in the TV mode. You may use this button in PIP mode as well.

6. TTX/MIX

3. +100

TV channels provide written information services via teletext.

Press to select channels over 100.

For more information > TTX / MIX

For example, to select channel 121, press "+100", then press "2" and "1".

TTX / MIX is mainly used in Europe.

-/-- (One/Two-Digit channel selection )

7. MENU

Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed.

Use this button to open the on -screen menu and exit from the menu screen or close screen

Enter the two-digit channel number.

adjustment menu.

-/-- is mainly used in Europe.

8. ENTER

4. - +

ctivates a highlighted menu item.

djusts the audio volume.

9. FM RADIO

5. MUTE

Turns on/off FM Radio.

Pauses (mutes) the audio output temporarily.

In PC/DVI mode, sets only SOUND to FM Radio.

Displays on the lower left corner of the screen.

In areas where signal is weak, noise may occur while FM radio is broadcast.

The audio resumes if Mute or - + is pressed in the Mute mode.

In general VIDEO SOURC E mode, sets to FM RADIO, turning off the screen.

6. TTX/MIX

10. CH/P

TV channels provide written information services via teletext.

In TV mode, selects TV channels.

For more information > TTX / MIX

TTX / MIX is mainly used in Europe.

11. SOURCE

Switches from PC mode to Video mode.

7. MENU

Changing the source is allowed only external devices that are connected to the monitor at

Use this button to open the on-screen menu and exit from the menu screen or close screen

the time.

adjustment menu.

12. INFO

8. ENTER

Current picture information displays on the upper left corner of the sc reen.

ctivates a highlighted menu item.

13. EXIT

9. FM RADIO

Exits from the menu screen.

Turns on/off FM Radio. In PC/DVI mode, sets only SOUND to FM Radio.

14. Up-Down Left-Right Buttons

In areas where signal is weak, noise may occur while FM radio is broadcast.

Moves from one menu item to another horizontally, vertically or adjusts selected menu

In general VIDEO SOURCE mode, sets to FM RADIO, turning off the screen.

values.

10. CH/P

15. AUTO

In TV mode, selects TV channels.

djusts the screen display automatically.

15. AUTO

16. P.MODE, M/B (MagicBright™)

17. P.SIZE

18. STILL

19. PIP

20. S.MODE

21. DUAL/MTS

22. PRE-CH

23. SOURCE

24. SIZE

25. POSITION

26. MAGIC-CH

A

11. SOURCE

16. P.MODE, M/B (MagicBright™)

When you press this button , current mode is displayed on the lower center of the screen.

Switches from PC mode to Video mode. Changing the source is allowed only external devices that are connected to the monitor at the time.

TV / AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode )

The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes.

12. INFO

( Dynamic Standard Movie Custom )

Current picture information displays on the upper left corner of the screen.

PC / DVI Mode : M/B ( MagicBright™ )

13. EXIT

MagicBright™ is a new feature providing the optimum viewing environment depending on

Exits from the menu screen.

the contents of the image you are watching. Then push button again to circle through available preconfigured modes.

14. Up-Down Left-Right Buttons

( Entertain Internet Text Custom )

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

17. P.SIZE - Not available in PC/DVI Mode

Press to change the screen size.

15. AUTO

ZOOM1, ZOOM2 are not available in 1080i(or over 720p) of DTV.

djusts the screen display automatically.(PC MODE)

18. STILL

16. P.MODE, M/B (MagicBright™)

Press the button once to freeze the screen. Press it again to unfreeze.

When you press this button, current mode is displayed on the lower center of the screen.

19. PIP

TV / AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode )

Push the PIP button to turn PIP screen On/Off.

The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes.

20. S.MODE ( Sound Mode )

( Dynamic Standard Movie Custom )

When you press this button , current mode is displayed on the lower center of the screen. The Monitor has a built-in high fi delity stereo amplifier.

PC / DVI Mode : M/B ( MagicBright™ )

Then push button again to circle through available preconfigured modes.

MagicBright™ is a new feature providing the optimum viewing environment depending on

( Standard Music Movie Speech Custom )

the contents of the image you are watching. Then push button again to circle through available preconfigured modes.

21. DUAL / MTS

( Entertain Internet Text Custom )

DUAL :

17. P.SIZE - Not available in PC/DVI Mode

can be operated depending on broadcasting type by using DUAL button on the remote control while watching TV.

Press to change the screen size.

Toggles MONO/STEREO , DUAL 1/DUAL 2 and MONO/NICAM MONO/NICAM STEREO

ZOOM1, ZOOM2 are not available in 1080i(or over 720p) of DTV.

MTS :

• Mono, Stereo, SAP (Separate Audio Program)

18. STILL

Set 'MTS' to ON to choose Mono, Stereo or SAP.

Press the button once to freeze the screen. Press it again to unfreeze.

22. PRE-CH

19. PIP

This button is used to return to the immediately previous channel.

Push the PIP button to turn PIP screen On/Off.

23. SOURCE

20. S.MODE ( Sound Mode )

Selects the Video source.

When you press this button, current mode is displayed on the lower center of the screen. The Monitor has a built-in high fidelity stereo amplifier.

24. SIZE

Then push button again to circle through available preconfigured modes.

You can switch the Picture Size.

( Standard Music Movie Speech Custom )

25. POSITION

21. DUAL / MTS

Changing the Position of the PIP window.

DUAL :

can be operated depending on broadcasting type by using DUAL button on the remote

26. MAGIC-CH

control while watching TV.

MagicChannel enables you to watch only certain channels.

Toggles MONO/STEREO, DUAL 1/DUAL 2 and MONO/NICAM MONO/NICAM STEREO

This function is available only in Korea.

MTS :

• Mono, Stereo, SAP (Separate Audio Program)

STEREO/MONO, DUAL l / DIAL ll and MONO/NICAM MONO/NACAM STE REO

You can select the MTS (Multichannel Television Stereo) mode.

STEREO/MONO, DUAL l / DIAL ll and MONO/NICAM MONO/NACAM STEREO

You can select the MTS (Multichannel Television Stereo) mode.

Set 'MTS' to ON to choose Mono, Stereo or SAP.

22. PRE-CH

This button is used to return to the immediately previous channel.

23. SOURCE

Selects the Video source.(PIP Mode)

24. SIZE

You can switch the Picture Size.

25. POSITION

Changing the Position of the PIP window.

26. MAGIC-CH

MagicChannel enables you to watch only certain channels.

This function is available only in Korea.

Connecting the monitor

1. Connecting to a Computer

1.

2-1.

2-2.

3.

4.

5.

6.

Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analog) connector on the video card.

Using the D-sub (Analog) connector on the video card.

Connect the signal cable t o the 15-pin, D-sub connector on the back of your monitor.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Using the DVI (Digital) connector on the video card.

Connect the DVI Cable to the DVI Port on the back of your Monitor.

Connect the audio cable for y our monitor to the audio port on the back of your computer.

Connect the audio cable for your monitor to the audio port on the back of your computer.

Connect the power cord insert a plug in a wall outlet.

Turn on both your computer and the monitor.

You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.)

You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer.

If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check

to see if the monitor status is set to analogue. Press Source button to have the monitor double-

check the input signal source.

2. Connecting to a Macintosh

1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER

port on the monitor. (Voltage is automatically adjusted by the power adapter.)

2. Using the D-sub (Analog) connector on the video card.

Connect the signal cable to the D-SUB port on the Macintosh computer.

Connect the signal cable t o the D-SUB port on the Macintosh computer.

3. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh

adapter (optional) referring to the switch configuration table shown on its rear.

4. Connect the audio cable for your monitor to the audio port on the back of your computer.

4. Turn on the monitor and Macintosh.

5. Turn on the monitor and Macintosh.

Connecting to other devices

1-1. Connecting AV Devices

This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a camcorder, or a DTV or a TV without disconnecting the PC. For detailed information on connecting

This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a

AV input devices, refer to User Controls under Adjusting Your Monitor.

camcorder, or a DTV or a TV without disconnecting the PC. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor.

The configuration at the back of the monitor may vary from prod uct to product.

The configuration at the back of the monitor may vary from product to product.

The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on.

1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal

of the monitor using the RCA or S-Video cable.

S-Video, RCA cable and EXT(RGB) cable is optional.

2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

3. Se lect AV or S-Video using the

3. Select AV or S-Video using the

4. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R

and L audio input terminals using audio cables.

1-2. Connecting EXT(RGB) - It only applies to AV DEVICE that supports SCART.

Connect to the DVD Devices input if the device has a DVD connector.You can watch DVD simply by

hooking up the DVD with the monitor as long as the power is on.

SOURCE

button on the monitor's front.

1. Connect a video cable between the EXT(RGB) jacks on the Monitor and the EXT(RGB) jacks on

the DVD Player.

2. Se lect Ext. by pressing

2. Select Ext. by pressing

2. Connecting TV

You may view television programs on the monitor if it is connected to an antenna or a CATV cable

without installing any separate TV reception hardware or software on your computer.

SOURCE

button on the monitor.

1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor.

You need to use a coaxial antenna cable.

When using an interior antenna terminal:

Check the antenna terminal on the wall first and connect the antenna cable.

When using an outdoor antenna:

If you are using an outdoor ante nna, use a professional for installation if possible.

If you are using an outdoor antenna, use a professional for installation if possible.

To connect the RF cable to the antenna input terminal:

Keep the copper wire portio n of the RF cable straight.

Keep the copper wire portion of the RF cable straight.

2. Turn on the monitor.

3. Select TV using Source button among the external signal adjustment buttons.

4. Select a desired TV channel.

Is weak signal causing poor reception?

Purchase and install a signal amplifier for better reception.

In areas where Antenna cable is not supported, first, attach Connecter to TV antenna .

3. Connecting DVD/DTV Set Top Box

Connect to the DVD/DTVS et Top Box input if the device has a DVD/DTV connector. You can watch

Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch

Component simply by hook ing up the Component with the monitor as long as the power is on.

Component simply by hooking up the Component with the monitor as long as the power is on.

1. Connect the Audio (R) and Audio (L) outputs on the DVD / DTV set top box to the Audio (R) and

Audio (L) inputs on the monitor using audio cables.

2. Connect a video cable between the component( P

2. Connect a video cable between the component( P jacks on the DVD / DTV se t top box.

jacks on the DVD / DTV set top box.

, PB,Y) jacks on the Monitor and the PR, PB,Y

R, PB,Y) jacks on the Monitor and the PR , PB,Y

R

3. Se lect Component using the

3. Select Component using the

4. Connecting Headphone

You may connect your Hea dphone to the monitor.

You may connect your Headphone to the monitor.

1. Connect your Headphone to the Headphone connection terminal.

Using the Stand

This monitor supports various types of VESA-standard bases. You need to either fold or remove the

base in use in order to install a VESA base.

1. Folding the base

The monitor may be reclined from -5 to 15 degrees.

SOURCE

button on the monitor's front.

2. Attaching a base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Monitor

A.

Mounting interface pad

B.

1. Turn off your monitor and unplug its power cord.

1. Turn off your monitor and unplug its pow er cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove four screws and then remove the Stand from the LCD monitor.

4. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with

4. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

four screws that came with the arm-type base, wall mount h anger or other base.

To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the

To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for

monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for more information.

more information.

Samsung Electronics will not be responsible for damages caused by using a base other than those

specified.

When prompted by the operating system for the monitor driver, insert the CD - ROM included

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to

with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and downl oad the driver program file at the Internet web site shown here.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung-monitor.com / (Worldwide)

Internet web site : http://www.samsung-monitor.com/ (Worldwide)

z

http://www.samsungusa.com/monitor (USA)

http://www.sec.co.kr/monitor (Korea)

http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

http://www.samsungmonitor.com.cn/ (China)

Windows ME

1. Insert CD into the CD-ROM drive.

2. Click

3. Choose your monitor model in the model list, then click the

"Windows ME Driver"

.

"OK"

button.

/

Windows XP/2000

4. Cli ck the

4. Click the

5. Monitor driver installation is completed.

1. Insert CD into the CD-ROM drive.

2. Click

3. Choose your monitor model in the model list, then click the

"Install"

"Windows XP/2000 Driver"

button in the

"Warning"

window.

"OK"

button.

4. If you can see following message window, then click the

click

5. Monitor driver installation is completed.

button.

"OK"

This monitor driver is under certified MS logo,and this installation doesn't damage

your system.The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung-monitor.com/ .

http://www.samsung-monitor.com

.

"Continue Anyway"

button. Then