Samsung 470D User Manual

4 CHANNEL DVR

User Manual

SRD-470/470D

Z6806127401A_SRD-470, 470D-IB_EN1 1Z6806127401A_SRD-470, 470D-IB_EN1 1 2010-04-30 오후 6:06:232010-04-30 오후 6:06:23

4 Channel DVR

User Manual

Copyright

©2009 Samsung Techwin Co., Ltd. All rights reserved.

Trademark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this
document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of
Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document
without prior notice.

Warranty

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this
document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of
Samsung Techwin.

Z6806127401A_SRD-470, 470D-IB_EN2 2Z6806127401A_SRD-470, 470D-IB_EN2 2 2010-04-30 오후 6:06:392010-04-30 오후 6:06:39

is the registered logo of Samsung Techwin Co., Ltd.

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.

1)

Read these instructions.

2)

Keep these instructions.

3)

Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water.

6)

Clean only with dry cloth.

7)

Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.

8)

Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifi ers) that produce heat.

9)

Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. if the provided
plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11)

Only use attachments/accessories specifi ed by the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or table specifi ed by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.

13)

Unplug this apparatus during lightning storms or when unused for long
periods of time.

14)

Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

English _3

Z6806127401A_SRD-470, 470D-IB_EN3 3Z6806127401A_SRD-470, 470D-IB_EN3 3 2010-04-30 오후 6:06:392010-04-30 오후 6:06:39

overview

BEFORE START

This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, etc.
You have to keep in mind the following notices :

SAMSUNG retains the copyright on this manual.

•

This manual cannot be copied without SAMSUNG’s prior written approval.

•

We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of

•

instructions mentioned in this manual.
Prior to opening the case, please consult a qualifi ed technician fi rst. Whenever this is needed power must be

•

removed from the unit.
Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this

•

DVR, check the compatibility. Consult your provider for the compatibility list.

Warning

Battery

❖

It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifi cations of the battery you are using now.

Normal voltage : 3V

•

Normal capacity : 170mAh

•

Continuous standard load : 0.2mA

•

Operating temperature : -20°C ~ +85°C

•

(-4°F ~ +185°F)

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”

J

❖

Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
Please turn off the power using the Power button on the front of your DVR.
After selecting <OK> in the pop-up menu, you can pull off the power cord.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

❖

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.

❖

This equipment is in door use and all the communication wirings are limited to inside of the building.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.



Batteries shall not be exposed to excessive heat such as sunshine, fi re or the like.



System Shutdown

Operating Temperature

Ethernet Port

Connect the power cord into a grounded outlet.



4_ overview

Z6806127401A_SRD-470, 470D-IB_EN4 4Z6806127401A_SRD-470, 470D-IB_EN4 4 2010-04-30 오후 6:06:402010-04-30 오후 6:06:40

CONTENTS

OVERVIEW

4

INSTALLATION

13

CONNECTING WITH OTHER DEVICE

17

LIVE

21

4 Before Start
7 Features
9 Part Names and Functions (Rear)
10 Part Names and Functions (Front)
12 Remote Control

 OVERVIEW

13 Checking the installation environment
14 HDD Addition

17 Connecting the Video, Audio, and Monitor
17 Connecting the USB
17 Connecting POS Device
18 Connecting the Alarm Input/Output
18 Connecting the RS485 Device
19 Connecting the Network

21 Getting Started
23 Live Screen Configuration
27 Live Mode
29 Spot Out
29 Zoom
30 Audio ON/OFF
30 Freeze
30 Event Monitoring

USING THE DVR

32

Z6806127401A_SRD-470, 470D-IB_EN5 5Z6806127401A_SRD-470, 470D-IB_EN5 5 2010-04-30 오후 6:06:402010-04-30 오후 6:06:40

32 System Setup
42 Setting the Device
50 Setting the Recording
53 Setting the Event
56 Backup
57 Network Configuration
64 Controlling a PTZ device

English _5

overview

SEARCH & PLAY

66

WEB VIEWER

70

BACKUP VIEWER

94

APPENDIX

96

66 Search
69 Playback

70 Introducing Web Viewer
71 Connecting Web Viewer
73 Using Live Viewer
79 Using Search Viewer
83 Viewer Setup
93 About

94 SEC Backup Viewer

96 Product Specification
99 Product Overview
100 Default Setting
103 Troubleshooting

6_ overview

Z6806127401A_SRD-470, 470D-IB_EN6 6Z6806127401A_SRD-470, 470D-IB_EN6 6 2010-04-30 오후 6:06:412010-04-30 오후 6:06:41

FEATURES

The SRD DVR (Digital Video Recorder) employs H.264 video encoding for 4 channel inputs and G.723 audio
encoding for 4 channels while simultaneously supports hard disc recording and playback.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video
and audio data.

4 CH Composite Input Connectors

•

CIF(S)/2CIF(M)/4CIF(L) Recording

•

Network transfer regardless of the recording conditions using network specifi c codec

•

Improved quality using de-interlace chip

•

HDD information and status with HDD SMART

•

Record at 4CIF Size (NTSC: 704*480, PAL: 704*576) 120(NTSC)/100(PAL)IPS

•

4 CH Loop Through video port

•

HDD Overwrite

•

Massive HDD backup via USB 2.0

•

Backup using USB 2.0 memory and/or external CD/DVD writer

•

(DVD writer not supported in SRD-470)
Record and play 4 CH video data simultaneously

•

Various search modes (time, event, backup, POS, motion detection)

•

Lots of storage modes (time lapse, event, timed recording)

•

HDD extension (USB 2.0)

•

Alarm connection (input: 4, output:2, reset: 1)

•

Remote monitoring via Windows Network Viewer

•

 OVERVIEW

English _7

Z6806127401A_SRD-470, 470D-IB_EN7 7Z6806127401A_SRD-470, 470D-IB_EN7 7 2010-04-30 오후 6:06:412010-04-30 오후 6:06:41

overview

Standards Approvals

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15



M

Package Contents

Please unwrap the product, and place the product on a fl at place or in the place to be installed.
Please check the following contents are included in addition to the main unit.

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

Remote Control Adaptor Power Cable

Network Viewer Software /

User Manual CD

HDD Fixing Screw

(Only applicable for SRD-470 : 4EA)

For models that are not equipped with the HDD, one SATA cable is provided for HDD installation.



M

User Manual Remote Control Battery (AAA)

SATA Cable

(Only applicable for SRD-470 : 1EA)

8_ overview

Z6806127401A_SRD-470, 470D-IB_EN8 8Z6806127401A_SRD-470, 470D-IB_EN8 8 2010-04-30 오후 6:06:422010-04-30 오후 6:06:42

PART NAMES AND FUNCTIONS (REAR)

1

2

3 4 5

11

Part Names Functions

VGA Output port for VGA video signal.

RS-232C RS-232C communications port.

VIDEO OUT BNC type of output port for the composite video signal.

Output port (RCA jack) for the audio signal.

AUDIO OUT

AUDIO IN 1~4 Output ports (RCA jacks) for the audio signal.

It is recommended to use an amplifi er-integrated speaker for the output of the audio



signal.

 OVERVIEW

678910

NETWORK Network connection port.

DC 12V Port to be connected to the 12V power source.

ALARM IN 1~4, G : Alarm input ports.

ALARM OUT 1, 2, COM : Alarm output ports.

RS485 Used to establish RS485 communications. (TX+, TX-)

USB USB connection port.

SPOT BNC type of output port for the Spot signal.

THROUGH Port to transfer the video signal to other video devices.

VIDEO IN

Input port for the composite video signal.
Supports both NTSC and PAL video signal.

English _9

Z6806127401A_SRD-470, 470D-IB_EN9 9Z6806127401A_SRD-470, 470D-IB_EN9 9 2010-04-30 오후 6:06:442010-04-30 오후 6:06:44

overview

PART NAMES AND FUNCTIONS (FRONT)

SRD-470

SRD-470D

1 3 5

2

SRD-470

8 7 69

3 5

21

4

SRD-470D

9

10_ overview

Z6806127401A_SRD-470, 470D-IB_EN10 10Z6806127401A_SRD-470, 470D-IB_EN10 10 2010-04-30 오후 6:06:452010-04-30 오후 6:06:45

8 7 6

Part Names Functions

Power LED : Displays the power ON/OFF status.

Power

Power Button : Used to turn the DVR ON/OFF.

In Live mode, pressing it will switch the mode to 4-split, PIP, and Auto Sequence in sequence.

MODE

In Search mode, pressing it will switch the mode to 9-split and 4-split in sequence.

For the Play Screen mode, refer to “Play”. (page

69)

AUDIO Sets Audio ON/OFF.

ALARM

Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the
icon.

REC Starts or ends the recording.

) : Used for backward frame-by-frame search while in PAUSE.

(-x2, -x4, -x8, -x16, -x32

, -x64)

/


►/

/

Step Rewind (
Fast Rewind () : Used for quick backward search while in Play.

Stop : Used to stop the playback.

Play/Pause : Used to pause or resume the screen.

Fast Forward () : Used for quick forward playback. (x2, x4, x8, x16, x32
Step Forward ( ) : Used for forward frame-by-frame search while in PAUSE.

Open/Close Used to open and close the DVR-RW disc tray. (available for SRD-470D only)

ALARM : Lights on when an event occurs.

HDD : Displays the normal access to HDD.

Upon access to HDD, LED repeats on and off.

LED Indicator

NETWORK : Displays both network connection and data transfer status.

BACKUP : Displays when Backup is in progress.

REC : Lights on when recording is in progress.

Direction &
Select Button

Used to change a value or move the cursor up/down/left/right (◄ ►).
Selects a menu item or executes the selected menu.

PTZ : Sets PTZ Mode ON/OFF.

ZOOM(TELE) : Sets the screen to the x2 digital zoom.

Runs the TELE function in the PTZ Mode.

Camera Control

FREEZE(WIDE) : Runs the FREEZE function in the Live Mode.

Runs the WIDE function in the PTZ Mode.

SEARCH(VIEW) : This is the function that switches over to the Search mode.

(Perform the VIEW function when selecting the PTZ button.)

MENU : Used to access the Menu screen or move to the previous menu.

Channel

Used to select channel numbers directly in the Live Mode, or numbers in the numeric input
mode.

 OVERVIEW

, x64)

USB Port Connects the USB devices.

English _11

Z6806127401A_SRD-470, 470D-IB_EN11 11Z6806127401A_SRD-470, 470D-IB_EN11 11 2010-04-30 오후 6:06:462010-04-30 오후 6:06:46

overview

REMOTE CONTROL

Displays the search menu.

Changes the screen mode.

Displays the Exit pop up screen.

Used as the numeric input keys, or displays a single

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

Goes to the system menu screen.

Up/Down/Left/Right(▲▼◄ ►)/ENTER

Moves the cursor up/down/left/right, and runs the

Freezes the screen temporarily.

Runs the digital zoom (x2) function.

Starts or ends the live recording.

Runs the View function in the PTZ mode.

SEARCH

MODE

POWER

NUMBER [0~+10]

channel.

T/W

Zooms in or out.

MENU

Select Menu.

FREEZE

ZOOM

REC

VIEW

BACKUP

Displays the Backup Menu.

OPEN/CLOSE

Opens or closes the CD tray.

DVR

Activates the DVR function.

ID

Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.

Move Frame

While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

PTZ

Displays or ends PTZ.

SCROLL ,.

Moves the menu scroll.

RETURN

Returns to the previous screen.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

REC LOCK

Selects the recording lock function.

PRESET

Displays the Preset Setup.

Using the Numeric buttons

1.

Press any button among 1 to 4.

2.

Move to the selected channel number.

Changing the Remote Control ID

1.

Press the ID button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.

2.

Enter 2 digits of your selection in order, while pressing the system [ID] button.

3.

When ID input is done, press the system [ID] button again to check the setting.

If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.



M

12_ overview

Z6806127401A_SRD-470, 470D-IB_EN12 12Z6806127401A_SRD-470, 470D-IB_EN12 12 2010-04-30 오후 6:06:462010-04-30 오후 6:06:46

Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 46)

installation

2

34

M

O
D

E

A

U

D

IO

A

L
A

R

M

R

E
C

Z

O

O

M

R
E

C

F

R

E

E

Z

E

S

E

A
R

C

H

T

E

L

E

W

I
D

E

V

I
E

W

M

E

N

U

B
A

C
K

U
P

N
E

T
W

O
R

K

H
D

D

A
L

A
R

M

DIGIT

AL VID

EO RECORDER

SRD-

470D

Please take note of the followings before using this product.

Do not use the product outdoor.

•

Do not spill water or liquid in the connection part of the product.

•

Do not impose the system to excessive shock or force.

•

Do not pull out the power plug forcefully.

•

Do not disassemble the product on your own.

•

Do not exceed the rated input/output range.

•

Use a certifi ed power cord only.

•

For the product with an input ground, use a grounded power plug.

•

CHECKING THE INSTALLATION ENVIRONMENT

 INSTALLATION

Samsung Digital Video Recorder (“DVR” hereinafter) is a
state-of-art security device, and contains mass storage hard

Temperature
Unit: ºC

One Year: 24HR X 365 DAY =8,760 HR

disk(s) and critical circuits inside.
When the temperature rises inside the product, the product

may breakdown and the product life be shortened. Please
pay attention to the following recommendations before
installation.

Life (Unit: HOURS)

[Figure 1]

The followings are the recommendations when Samsung DVR is installed on a rack.

Please ensure that the rack inside is not sealed.

1.
Please ensure the air is circulated through the inlet/outlet as shown in the picture.

2.
If the DVR or other devices on a rack is to be stacked as in the picture, provide a

3.
suitable space or install a ventilating opening for air circulation.

For natural air convection, place the inlet at the bottom of the rack and the outlet on

4.
top.

It is strongly recommended that a fan motor is installed at the inlet and the outlet for air

5.
circulation. (Please fi t a fi lter at the inlet to screen dust or foreign substances.)

Please maintain the temperature inside the rack or surrounding areas between 0°C ~

6.

D
I
G

I
T
A
L
V

I
D
E
O

R
E
C

O
R

D
E
R

S
R

D

­4

7
0
D

M
O
D
E

A
U
D
I
O

L
A

A

R
M

L
A
R
M

H

1

D
DA

N
E
T
W

O
R
K

B

2

R

A

E

C
K

C

U
P

R
E
C

3

4

Z
O
O

M

F
R
E

E
Z
E

S

E
A
R

C

T

H
E
L

E

M
E
NU

W

ID
E

V
I
E

W

D
I
G

I
T
A
L
V

I
D
E
O

R
E
C

O
R

D
E
R

S
R

D

­4

7
0
D

M
O
D
E

A
U
D
IO

A
L
A

A

R
M

LA
R
M

H

1

D
D

N
E
T
W

O
R
K

B

2

R

A

E

C
K

C

U
P

R
E
C

3

4

Z
O
O

M

F
R
E

E
Z
E

S

E
A
R

C
T

H
E
L

E

M
E
N

U

W

ID
E

VI
EW

D
I
G

I
T
A
L
V

I
D
E
O

R
E
C

O
R

D
E
R

S
R

D

­4

7
0
D

M
O
D
E

A
U
D
I
O

A
L
A

A

R
M

L
A
R
M

H

1

D
D

N
E
T
W

O
R
K

B

2

R

A

E

C
K

C

U
P

R
E
C

3

4

Z
O
O

M

F
R
E

EZ
E

S

E
A
R

C
T

H
E
LE

M
E
NU

W

ID
E

VI
E

W

D
I
G

I
T
A
L
V

I
D
E
O

R
E
C

O
R

D
E
R

S
R

D

­4

7
0
D

M
O
D
E

A
U
D
IO

A
L
A

A

R
M

L
A
R
M

H

1

D
D

N
E
T
W

O
R
K

B

2

R

A

E

C
K

C

U
P

R
E
C

3

4

Z
O
O

M

F
RE

E
Z
E

S

E
A
R

C
T

H
E
L

E

M
E
NU

W

ID
E

VI
E

W

40°C (32°F ~ 104°F) as shown in the fi gure 1.

Rack Mount Instructions - The following or similar rack-mount instructions are
included with the installation instructions :

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specifi ed by
the manufacturer.

[Figure 2]

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of air fl ow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is

not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit

and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should

be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

English _13

Z6806127401A_SRD-470, 470D-IB_EN13 13Z6806127401A_SRD-470, 470D-IB_EN13 13 2010-04-30 오후 6:06:482010-04-30 오후 6:06:48

installation

HDD ADDITION

You can install additional HDDs.
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product
damage.
Please consult your provider for further information on HDD installation since improper installation or settings may
damage the product.

Number of HDDs supported : SRD-470 : Default 1 HDD + Up to 1 HDD added



SRD-470D : Default 1 HDD

Make sure to unplug the power cord from the wall outlet before proceeding with the installation.





J

Cautions for data loss (HDD care)

Please pay attention so that the data inside the HDD is not damaged.
Before adding a HDD, please check the compatibility with this DVR product.
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.
Please ensure that the HDD is free from such shock.
We are not liable for any damage to the HDD incurred by user’s carelessness or miss use..

Cases might cause damage to HDD or recorded data



To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.
Data may be lost due to external impacts during disassembly or installation of the DVR.
HDD may be damaged if the DVR is suddenly stopped by a power cut or power off during operation.
HDD or fi les stored inside may be damaged if the main body is moved or impacted during the HDD operation.

Cautions when adding a HDD

When adding a HDD, ensure that the cable does not get caught or the insulation does not come off.

1.

Pay attention so as not to lose the disassembly screws or accessories.

2.

If the screws or accessories are not put together correctly, the product may breakdown or not operate properly.



Please check the HDD compatibility before adding a HDD.

3.

Please contact your nearest dealer to obtain the list of compatible devices.



14_ installation

Z6806127401A_SRD-470, 470D-IB_EN14 14Z6806127401A_SRD-470, 470D-IB_EN14 14 2010-04-30 오후 6:06:512010-04-30 오후 6:06:51

First, loosen the screws on both sides and remove

1.

the cover.

Loosen the left and right screws on the lower hard

2.

disk bracket to remove it.

 INSTALLATION

Insert the additional hard disk into the bracket and

3.

fi x it using the provided screws.

Hard disk bracket

Master hard disk

English _15

Z6806127401A_SRD-470, 470D-IB_EN15 15Z6806127401A_SRD-470, 470D-IB_EN15 15 2010-04-30 오후 6:06:512010-04-30 오후 6:06:51

installation

Insert the bracket where the additional hard disk is

4.

inserted into the lower bracket and fi x it using the
provided screws.

When done, connect the power cable and connect

5.

the signal cable (SATA cable) to the connector for
the main board.

SATA2
SATA1

Check if the connectors are properly connected

6.

and there is no problem with wiring, and close the
cover and fi x it with screws.

16_ installation

Z6806127401A_SRD-470, 470D-IB_EN16 16Z6806127401A_SRD-470, 470D-IB_EN16 16 2010-04-30 오후 6:06:572010-04-30 오후 6:06:57

connecting with other device

CONNECTING THE VIDEO, AUDIO, AND MONITOR

VIDEO OUT(VGA)

MONITOR

VIDEO IN

VIDEO OUT

SPOT OUT

AUDIO OUT

AUDIO IN

CONNECTING THE USB

There is one USB port at the front and one at the back of the product.

1.

You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.

2.

If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >

3.

Storage Device”. (Page
This product supports hot-plugging, which connects/removes the USB device during the system operation.

4.

44)

 CONNECTING WITH OTHER DEVICE

If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.



J

CONNECTING POS DEVICE

You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with

1.

a RS-232C cable.
Connection setup for the RS-232C port is available in “Menu > Device > POS Devices”, press the

2.

<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit and Transfer Type>. (Page

Z6806127401A_SRD-470, 470D-IB_EN17 17Z6806127401A_SRD-470, 470D-IB_EN17 17 2010-04-30 오후 6:07:032010-04-30 오후 6:07:03

47)

English _17

connecting with other device

CONNECTING THE ALARM INPUT/OUTPUT

Connecting the alarm input signal

Connection port for the alarm input signal.
Connect one strand of the sensor signal line (two

strands) to the alarm input port and connect the other
to the [G] port.

Connecting the alarm output signal

Connection port for the alarm output signal.
Connect one strand of the sensor signal line

(two strands) to the alarm output port and connect
the other to the [COM] port.

ALARM IN ALARM OUT

CONNECTING THE RS485 DEVICE

Connect the rear [RS485 +, –] ports to the external device.

ex) you can connect and control the PTZ camera



M

which supports the RS485 communication.
Check if the RS485 device is compatible with the



product fi rst.
Pay attention not to change the polarity (+/-) of the



RS485 device when connecting it.
Depending on camera’s type, connection polarity can



be different.
For further information, refer to the respective PTZ
Camera’s documentation.

RS485

18_ connecting with other device

Z6806127401A_SRD-470, 470D-IB_EN18 18Z6806127401A_SRD-470, 470D-IB_EN18 18 2010-04-30 오후 6:07:052010-04-30 오후 6:07:05

CONNECTING THE NETWORK

Connecting to Internet through Ethernet (10/100/1000BaseT)

RJ-45 Ethernet Cable
(Direct Cable)

 CONNECTING WITH OTHER DEVICE

INTERNET

Hub/Switcher

Back Bone

Connecting to the Internet using the router

INTERNET

Hub/Switcher

Windows
Network Viewer

Router

xDSL or Cable

Modem

DDNS Server
(Data Center)

xDSL or Cable

Modem

External Remote

PC

English _19

Z6806127401A_SRD-470, 470D-IB_EN19 19Z6806127401A_SRD-470, 470D-IB_EN19 19 2010-04-30 오후 6:07:062010-04-30 오후 6:07:06

connecting with other device

Connecting to Internet through ADSL

RJ-45 Ethernet Cable
(Direct Cable)

INTERNET

Hub/Switcher

Phone(ADSL) Line

ADSL MODEM

Windows
Network Viewer

20_ connecting with other device

Z6806127401A_SRD-470, 470D-IB_EN20 20Z6806127401A_SRD-470, 470D-IB_EN20 20 2010-04-30 오후 6:07:082010-04-30 오후 6:07:08

live

GETTING STARTED

Starting the system

1.

Connect the power cable of the DVR to the wall outlet.

2.

Press the Power button on the front panel.

3.

You will see the initialization screen.
The initialization process will last about 1 minute.
If a new HDD is installed, the initialization process may
take longer.

4.

The live screen appears with a beep.

 LIVE

REC

REC

Shutting Down the System

You can shut down the system only if you have logged in to the DVR.
You require permission to shut down the system if you are not logged in as admin.

1.

Press the [POWER] button on the remote control or the
front panel, or right-click to display the context sensitive
menu and select <Shutdown>.

2.

The “Shutdown” confi rmation window appears.

3.

Use the arrow keys on the remote control or the front panel
to move to <OK> and press the [ENTER] button or click
<OK>.
The system will shut down.



M

Z6806127401A_SRD-470, 470D-IB_EN21 21Z6806127401A_SRD-470, 470D-IB_EN21 21 2010-04-30 오후 6:07:092010-04-30 오후 6:07:09

For the permission management, refer to “Permission
Management > Setting Permissions”. (Page 37)

Shutdown

Are you sure to shutdown?

OK Cancel

English _21

live

Login

To access a DVR or restricted menu, you should have logged in to the DVR.

1.

In live mode, right-click any area of the screen.
You will see the context sensitive menu as in the right
fi gure.

2.

Click <Login>.
The login dialog appears.
You can also see the login dialog to access a desired menu
by pressing the [MENU] button on the remote control or
the front panel.

The login dialog will also appear if you press a menu button on



the remote control or the front panel of the DVR when the
corresponding menu requires logging in.

After logged in, press [RETURN] on the remote control to display



the logout dialog.



By default, initial ID and password are set to “admin”, and “4321”.

Login

ID admin

x

Password

x

OK Cancel

Scene Mode

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Login





M

For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page

Locking All Buttons

This will restrict access to all buttons available in the DVR.

1.

In Live mode, press buttons in the order of [STOP]
[FREEZE][STOP][FREEZE][MENU].
All buttons will be locked.

In the lock condition, press any button to display a dialog

2.

where you are prompted to enter the password for
unlocking the buttons.
The button lock will be released if you enter the admin
password.



Key Lock Password

ID admin

x

Password

x

OK Cancel

37)

22_ live

Z6806127401A_SRD-470, 470D-IB_EN22 22Z6806127401A_SRD-470, 470D-IB_EN22 22 2010-04-30 오후 6:07:142010-04-30 오후 6:07:14

LIVE SCREEN CONFIGURATION

CAM 01

Icons on the Live Screen

You can check the status or operation of the DVR with the icons on the live screen.

2010-01-01 00:00:01

CAM 01

Name Description

Current Date, Time

Login Information

Displays the current time and date.

When you are logged in, the “LOG ON” icon will be displayed.

Displayed if the zoom function is activated.
Displayed if you press the Pause button.

Screen Mode

Displayed in Auto Sequence mode where all channels are switched at the
specifi c time interval.

Displayed if the recording is in process.
M To cancel the recording, enter the password.

Displayed if there is a problem with the cooling fan.

Displayed if the HDD is full and the DVR has an insuffi cient space to record.

System Operation

Displayed if no HDD is installed or the existing HDD should be replaced.
Displayed if the HDD needs a technical examination.
Displayed if a new fi rmware is found from the network.

Video Input Status

Displayed if no input is entered in the condition that the camera is set to <ON>.
Nothing will be displayed on the screen if the camera is set to <OFF>.

 LIVE

Camera Name/ Channel

Displays the camera name and the changed channel, if any.

Displays the resolution of the recording screen. (Page 52)

Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
Displays AUDIO ON/MUTE.

Not displayed in video mode if deactivated.

Camera Operation

If the sensor is set to <ON>, the input signal will be displayed on the screen of
the connected channel.

Displayed if a motion detected in the condition that the motion detection is set to
<ON>.

Displays the current record mode from Record/Event/Schedule.

English _23

Z6806127401A_SRD-470, 470D-IB_EN23 23Z6806127401A_SRD-470, 470D-IB_EN23 23 2010-04-30 오후 6:07:202010-04-30 오후 6:07:20

live

Error Information

If you turn on the system when the internal HDD is not connected or an error occurs, the “HDD FAIL” icon

•

) will be displayed on the top left corner. In this case, make sure you contact the service center for

(
assistance as this may cause a failure of recording, playback or backup.

If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and

•

the fan error icon (
works.
As a fan error can shorten the product life, make sure you contact the service center for assistance.

If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.



M

Live Screen Menu

In addition to the buttons on the front panel or the remote control, you can access a desired menu by right­clicking the mouse any area in live mode.
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/
logout, screen split mode and DVD operation mode.

Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.



M

) will be displayed on the top left corner. In this case, check to see if the internal fan

Scene Mode

Scene Mode

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Login



PTZ Control

ZOOM

Audio

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Login

PTZ Alarm Freeze





< Split Mode Menu >

< Single Mode Menu >

Split Mode Menu

The context sensitive menu in split mode differs, depending on the login/logout status.

Scene Mode

1

2

3

4

5

6

7

8

9

10

11

12

13

24_ live

Z6806127401A_SRD-470, 470D-IB_EN24 24Z6806127401A_SRD-470, 470D-IB_EN24 24 2010-04-30 오후 6:07:222010-04-30 오후 6:07:22

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Logout





Menu Description

Scene Mode Refer to “Live Mode”. (Page 27)

Spot Out Refer to “Spot Out”. (Page 29)

Audio On/Off Refer to “Audio ON/OFF”. (Page 30)

Freeze Refer to “Freeze”. (Page 30)

Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 30)

Record/Stop Starts/stops the standard recording.

Play Plays the search result (data). Refer to “Search & Play > Play”. (Page 69)

 LIVE

Search Refer to “Search & Play > Search”. (Page

66)

Backup Refer to “Using the DVR > Setting the Backup”. (Page 56)

Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 32)

Shutdown

Show/Hide Launcher

Turns down the DVR.

Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 26)

Login/Logout You can log in or out.

Single Mode Menu

The single mode menu is available only in Single Mode.
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.

1

2

3

Full Screen

Spot Out

PTZ Control

ZOOM

Audio

Freeze

Stop Alarm

Record

Play

Shutdown

Hide Launcher

Logout





PTZ Alarm Freeze

Menu Description

Full Screen

PTZ Control

Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.

Accesses the PTZ Control menu. The PTZ menu is activated only in One-Channel Live mode.
(Page

64)

ZOOM Enlarges the selected image. (Page 29)

English _25

Z6806127401A_SRD-470, 470D-IB_EN25 25Z6806127401A_SRD-470, 470D-IB_EN25 25 2010-04-30 오후 6:07:302010-04-30 오후 6:07:30

live

View the Launcher Menu

The Launcher menu appears on the bottom of the live screen.

1.

In Live mode, right-click to display the context menu and
select <Show Launcher>.

2.

Move the cursor to the bottom and click a desired item in
the Launcher menu.

If no input is entered for 10 seconds, the menu will disappear.



M

The Launcher menu can be accessed only by using the mouse.



PTZ

Menu Description

Alarm Freeze

Displays the current time and date.

Date/Time

Screen Mode Displays in the sequence of 4-split, PIP and Auto Sequence.

Menu Expansion Button Click to display the hidden menu to the right.

Audio Turns ON/OFF the sound of the selected channel.

Zoom Enlarges the selected area. This is available only in Single Live mode.

PTZ Runs the PTZ Control launcher.

Alarm Stops the alarm if it's activated.

Freeze Freezes the Live screen temporarily.

Play Enters Play mode if a fi le to play exist, and if not, enters Search mode.

Record Start/End recording the Live screen.

The indication of AM/PM is displayed if you set 12 hours for the time format in
“System > Date/Time/Language > Time”. (Page

32)

26_ live

Z6806127401A_SRD-470, 470D-IB_EN26 26Z6806127401A_SRD-470, 470D-IB_EN26 26 2010-04-30 오후 6:07:332010-04-30 오후 6:07:33

LIVE MODE

Displays 4 live video images in 3 different modes.

Switching the screen mode

To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the front panel or the remote control to switch the mode in the sequence of the
launcher menu items.

CH1 CH2



CH3 CH4

CH1

4-split mode PIP Auto Sequence

Switching the screen automatically

With SRD-470/470D, you can display 4 live single screens in sequence.

CH2



CH1

 LIVE

CH1

CH1

M

CH1

CH1

Single mode

In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be



1

4

conducted at the set interval. (Page 42)

English _27

Z6806127401A_SRD-470, 470D-IB_EN27 27Z6806127401A_SRD-470, 470D-IB_EN27 27 2010-04-30 오후 6:07:352010-04-30 오후 6:07:35

live

Channel Setting

You can display the channel in a desired area of a split screen.

Place the cursor over the camera name of each channel to display the <

1.

Click a camera name to display a channel list where you can select a different channel.

2.

Select a desired channel and click it.

3.

The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
change the channel position.

Ex : if switching CH 1 to CH 4



▼

> key to the right on the screen.

CH1 CH2

CH4 CH2



CH3 CH4

Switching to Single Mode

When in split mode, select and double-click a desired channel to switch to its Single mode.
Press the number corresponding to a desired channel on the front panel or the remote control to switch to its
Single mode.
Refer to “Remote Control > Using the numeric buttons”. (Page 12)

Ex : If double-clicking CH 3 or pressing the number “3” on the remote control or the front panel.



CH1 CH2

CH3 CH1



CH3 CH4

CH3

28_ live

Z6806127401A_SRD-470, 470D-IB_EN28 28Z6806127401A_SRD-470, 470D-IB_EN28 28 2010-04-30 오후 6:07:362010-04-30 오후 6:07:36

SPOT OUT

The Spot Out monitoring is independent of the Live mode, which monitors a specifi c channel through the Spot Out
port.

Selecting a Spot Out mode

If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you
can select a output screen mode.

1.

In Live mode, right-click any area on the screen.
The Live menu appears.

2.

Click Spot Out.
Supports the Spot output in Single screen with Auto
Sequence mode.

The Spot output is supported only for a designated channel.



For the Spot Out port of a model, refer to “Part Names and
Functions (Rear)”. (Page 9)

Scene Mode



Spot Out



Spot Out 1

Auto Sequence

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Logout



Single

CH1



CH2

CH3

CH4

< Multichannel Live Menu >

ZOOM

 LIVE

This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.

1.

Select <ZOOM> in the right-click menu.
Press the [ZOOM] button on the front panel or the remote control, or simply click <

> in the launcher

menu. The zoom box appears.
Use the direction keys, or drag and drop to specify an area to enlarge.

2.

Press the [ENTER] button, or double-click the selected area to enlarge it twice.

3.

In the enlarged image, use the direction buttons (◄ ►) on the remote control or the front panel to move the



enlarged area.

Press the [ZOOM] button on the front panel or the remote control, or simply click < > in the launcher

4.

menu to release the zoom.



English _29

Z6806127401A_SRD-470, 470D-IB_EN29 29Z6806127401A_SRD-470, 470D-IB_EN29 29 2010-04-30 오후 6:07:372010-04-30 오후 6:07:37

live

AUDIO ON/OFF

You can turn the sound on/off corresponding to the channel in Live mode.

AUDIO ON/OFF in Single mode

Click the audio icon ( ) on the screen, or press the [AUDIO] button on the front panel or the remote control
to turn it on/off.



M

FREEZE

This is available only in Live mode, this pauses playing the Live image temporarily.

1.

2.

Only the channel where <AUDIO> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live
mode that you can use to turn the sound on/off.

Press the [FREEZE] button on the front panel or the remote control, or click <
menu.
The playback of the image is stopped temporarily.

Press the [FREEZE] button again, or click <
This will release the freeze.

Freeze

>.

Freeze

> in the launcher

EVENT MONITORING

This will display the channel in sync with a specifi c event (Sensor/Motion/Video Loss) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 48)

If multiple events occur simultaneously, the screen will switch to a split mode.

•

- 2~4 events : 4-split mode
If the second event occurs within the set time of <Event Display>, the fi rst event will last until the second

•

30_ live

one is terminated. (Page

Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.



Event occurrence 5 seconds

CH1

48)

Stop alarm

Z6806127401A_SRD-470, 470D-IB_EN30 30Z6806127401A_SRD-470, 470D-IB_EN30 30 2010-04-30 오후 6:07:462010-04-30 오후 6:07:46

Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the fi rst



event occurred in CH 1.

Event occurrence 4 seconds 9 seconds

M

Stop alarm

CH1 CH2

CH1

Press the [ALARM] button to reset the alarm settings and to release the event mode.



If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will



be performed.

 LIVE

English _31

Z6806127401A_SRD-470, 470D-IB_EN31 31Z6806127401A_SRD-470, 470D-IB_EN31 31 2010-04-30 오후 6:07:472010-04-30 오후 6:07:47

using the DVR

You can setup the system properties, devices, and options for recording, event,
backup and network.

SYSTEM SETUP

You can setup Date/Time/Language, Permission, System Properties and Log.

Date/Time/Language

You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.

Setting the Date/Time/Language

Set the Date/Time/Language

Using the mouse may help make setup easier.

1.

Press the [MENU] button on the remote control or on the
front panel.

If not logged in, it prompts with login window.



Refer to “Login”. (Page 22)

Use the left/right buttons (

2.

◄ ►

) to select the <System>.

System property setup menu is selected.

3.

Use the up/down buttons (
Language> and press the [ENTER] button.

Select <Date/Time/Language>.

4.

A dialog to setup Date, Time and Language.

Use direction buttons (

5.



◄ ►

) to select <Date/Time/

) to select an item to set

System

Date/Time/Language
Permission Management
System Management
Log Information

and make your changes.

Date : Sets the date that will appear on the screen.

•

You can select the date format.

•

Time : Sets the time and its format that will appear on the
screen.
Select either one from <24 Hours, 12 Hours (AM/PM)>.

•

Time Zone : Sets the time zone of your area based on the
Greenwich Mean Time (GMT).

GMT (Greenwich Mean Time) is standard World Time and the basis



of world time zone.

Time Sync. : You can set the DVR’s current time

•

Date/Time/Language

Date/Time/Language

Date 2010-01-01 YYYY-MM-DD

x

Time 08:14:24 24 Hours

x

Time Zone GMT+09:00

x

Time Sync.

x

DST

x

Language English

x

Holiday

Setup

Dec First (Sun) 0 Dec First (Sun) 0

OK Cancel

synchronized to a selected <Time Server> regularly if you select to use <Time Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.

Logout

Exit

32_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN32 32Z6806127401A_SRD-470, 470D-IB_EN32 32 2010-04-30 오후 6:07:472010-04-30 오후 6:07:47

- Time Server : Enter an IP or URL address of the time
server.

- Last Sync Time : Displays the most recent
synchronization time from the selected time server.

- Activate as Server : Set to <Use> to allow the DVR to act
as a Time Server for other DVRs.

•

DST : Set up Daylight Saving Time with its period to make
the time earlier than the GMT of its time zone by 1 hour
during the set period.

•

Language : Select your language. Sets the language for the

Date/Time/Language

Date/Time/Language

Date 2010 -01-01 YYYY-MM-DD

x

Time Synchronization Setup

Synchronization Use

x

Time 08:14:24 24 Hours

x

Time Server 203.248.240.103

x

Time Zone GMT+08:00

x

Last Sync Time Fail

x

Time Sync.

x

Activate as Server Use

x

DST

x

Language English

x

Holiday

Setup Not Used

Dec First (Sun) 0H Dec First (Sun) 0H

OK Cancel

OK Cancel

interface.
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,
Turkish, Czech, Danish, and Swedish are available.

6.

When the Date/Time/Language setup is done, press <OK>.

You can also use numeric buttons on the remote control or front panel to enter values for Date, Time and other



M

numeric fi elds.

Setting Holiday

You can set specifi c dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Date/Time/Language> window to select <Date/Time/Language>, and

3.

press the [ENTER] button.

4.

Select <Holiday>.
A calendar for Holiday setup appears.

5.

Use the left/right <

> buttons to select year or month,

and press the [ENTER] button.

Date/Time/Language

Date/Time/Language

2010 Jan

Sun Mon Tue Wed Thu Fri Sat
1 2

3 4 5 6 7 8 9

10 11 12 13 14 15 16

17 18 19 20 21 22 23

24 25 26 27 28 29 30

31

Holiday

 USING THE DVR

OK Cancel

6.

Use direction buttons (
and press the [ENTER] button.
You will see the “Setting Holiday” screen.

Ex : Select January 11th and check on <1/11> only to make



every January 11th a holiday. Check both on <1/11> and <Jan
2nd Mon> to make every January 11th and 2nd Monday of

January holidays.

When the Holiday setup is done, press <OK>.

7.

◄ ►

) to select a desired date,

Date/Time/Language

Date/Time/Language

2010 Jan

Setting Holiday

Sun Mon Tue Wed Thu Fri Sat
1 2

3 4 5 6 7 8 9

10 11 12 13 14 15 16

17 18 19 20 21 22 23

24 25 26 27 28 29 30

31

Holiday

1 / 11

Jan 2nd Mon

OK Cancel

OK Cancel

Using the Calendar

Using the mouse may help make setup easier.

{

Select year and month.
Select the left/right < > key on the left/right side of year/month and press [ENTER] button to
adjust by 1 year/month.

|

Use direction buttons to select a date and press [ENTER] button.

A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event



Search.

English _33

Z6806127401A_SRD-470, 470D-IB_EN33 33Z6806127401A_SRD-470, 470D-IB_EN33 33 2010-04-30 오후 6:07:512010-04-30 오후 6:07:51

using the DVR

Permission Management

You can set permissions of each user over the DVR's specifi c function and settings.

Setting the Administrator

You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <Permission Management>, and press
[ENTER] button.

Select <Admin>.

4.

A dialog for Admin ID and Password input appears.

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and set the ID and password.

Permission Management

Admin

ID admin

x

Password

x

Confi rm P/W

x

Group

********

********

User Setup

M

6.

“4321”.

When the administrator setup is done, press <OK>.

By default, initial ID and password are set to “admin”, and



Using Virtual Keyboard

{

For alphanumeric inputs, the virtual keyboard window

appears.

|

Use direction buttons (

character, and press the [ENTER] button.

}

In the upper text input box of the virtual keyboard, there

displays a list of candidate words containing the selected
character.

~

Select a word from the list, or use the keyboard to enter the

whole word.

If there are many of candidate words, use < , > buttons to move between them forward and backward.



You can use mouse wheel and jog shuttle button too.



Select <OK>.



Entered word is applied.



For upper case letters, use <Caps Lock> button.



For special characters, use <Shift> button.



Using the virtual keyboard is the same to a normal keyboard use in your region.



You can enter only lower-case alphabets and numeric values for the user ID.



For the password, use alphabets and special characters excluding < \ > and <“>.



You can use number buttons on the remote control or front panel.

◄ ►

) to move to a desired

OK Cancel

` 1 2 3 4 5 6 7 8 9 0 - =

q w e r t y u i o p [ ] \

a s d f g h j k l ; ‘

z x c v b n m , . /

Space Ctrl

OK Cancel

Caps Lock

Shift



Del

34_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN34 34Z6806127401A_SRD-470, 470D-IB_EN34 34 2010-04-30 오후 6:07:542010-04-30 오후 6:07:54

Setting the Group

You can create user groups and setup permissions for those user groups.
You can register a user for each group in <User>.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <Permission Management>, and press
[ENTER] button.

Select <Group>.

4.

A window for <Add>, <Delete>, <Rename>, and
<Group Authority> setup appears.

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and set the value.

Add, Delete, Rename : You can add, delete, rename a

•

group or modify the permissions given to the group.
The virtual keyboard appears when <Add> or <Rename> was selected.
You can add up to 10 groups.

-

Add : When you fi rst run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10
groups.

- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts

belonging to that group.

- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.

For entering a group name, refer to “Using Virtual Keyboard”. (Page 34)



Group Authority : Sets permissions to access menu items of each group.

•

Users of a group can access checked functions.

When the group setup is done, press <OK>.

6.

Permission Management

Admin

Group

x

Group Authority

Group

Live View

Search

Backup

Menu

Record Lock PTZ Remote Alarm Out Shutdown

Setup

Setup

Setup

Setup

User

Add Delete Rename

OK Cancel

Setup

 USING THE DVR

To set the group authority

You can set the permissions of the group users to access the menu according to the channel.

1.

Select a menu to which the group permission is assigned.
The menu where the group permission is assigned will be
displayed in the Live menu when a group user logs in.

•

Live View : You can set the permission to access the Live
screen according to the channel.

•

Search : You can set the permission to access the Search
menu according to the channel.

•

Backup : You can set the permission to access the Backup
menu according to the channel.

•

Menu : You can set menus accessible with a specifi c
permission.
Group users can access the permitted menus only.
Select a menu to display the Menu Permission screen.

•

Record Lock, PTZ, Remote Alarm Out, Shutdown : Select
an item so that the item will be added to the permissions.

2.

Select <OK>.
Select and assign a group user so that the user can
access the specifi ed menu.

Permission Management

Admin

Group ABC

x

Group Authority

Permission Management

Menu Permission

Admin

All

System

Group ABC

x

Group Authority

Date/Time/Language

Date/Time/Language Holiday

System Management

System Information Settings

Log Information

System Log Event Log Backup Log

Group

Channel Setup

Live View

Search

Backup

Menu

Record Lock PTZ Remote Alarm Out Shutdown

Live View

Search

Backup

Menu

Record Lock PTZ Remote Alarm Out Shutdown

Setup

All

Setup

1 2 3 4

Setup

Setup

Group

Device Record Event Backup Network

Setup

Setup

Setup

Setup

OK Cancel

OK Cancel

OK Cancel

OK Cancel

User

Add Delete Rename

User

Add Delete Rename

Setup

Setup

English _35

Z6806127401A_SRD-470, 470D-IB_EN35 35Z6806127401A_SRD-470, 470D-IB_EN35 35 2010-04-30 오후 6:07:562010-04-30 오후 6:07:56

using the DVR

To restrict the user permissions

If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.

Start the DVR.

1.

If all permissions are restricted, only the Login dialog
should appear.

Log in with a registered user ID.

2.

Right-click any area on the screen.

3.

If all permissions are restricted, only the accessible context
menus should appear.

Login

ID abc

x

Password

x

OK Cancel

Scene Mode

Audio Off

Freeze

Stop Alarm

User Menu

Hide Launcher

Logout



To change the user password

If you log in with a user account that is restricted to access the menu, you can change your own password
only.

1.

Log in with your account.

2.

Select <User Menu>.
The Permission Management setup screen appears.

3.

Select <Permission Management>.
The Password setup dialog appears.

4.

Enter a new password.

5.

Select <OK>.
You change to the password will be applied.

Permission Management

User

ID

x

Password

x

Confi rm P/W

x

abc

********

********

OK Cancel

36_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN36 36Z6806127401A_SRD-470, 470D-IB_EN36 36 2010-04-30 오후 6:07:592010-04-30 오후 6:07:59

Setting the User

Users can be added only if a group was created in <Group> menu.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <Permission Management>, and press
[ENTER] button.

Select <User>.

4.

A window for Add User appears.

Use direction buttons (

5.

window.
A window for “Add User” appears.
You can confi gure the Network Viewer settings including
name, ID, viewer, Select Group and password.
Result of the user setup appears in the <User> window.
To change the user property, use “Edit User”.
The “Edit User” window appears when you select a
desired item to be changed in the <User> window.

•

Viewer : If you select <Use>, you will be given access to the
Web Viewer and Network Viewer.

Refer to “Connecting Web Viewer”. (Page 71)





For more information about use of Network Viewer, refer to the
Network Viewer's user guide. (Page

When the user setup is done, press <OK>.

6.

◄ ►

) to select <Add> from the

8)

Permission Management

Admin

Group All Group

x

Group Name ID Viewer Delete

Permission Management

Admin

Group All Group

x

Group Name ID Viewer Delete

Group

Group

Add User

Name Kim

x

ID ksh

x

Viewer Not Used

x

Select Group ABC

x

Password

x

Confi rm

x

User

OK Cancel

User

********

********

OK Cancel

OK Cancel

Setup

Previous/Next Page

Setup

Previous/Next Page

Add

 USING THE DVR

Add

Setting Permissions

You can set restricted access for all general users.
Items with restrictions will require logging in for use.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <Permission Management>, and press
[ENTER] button.

Select <Setup>.

4.

The Restricted Access, Restriction on Network Access,
Auto Log out, Manual Input of ID setup screen appear.

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and set the value.

Restricted Access : All menu items allowed for a user can

•

be set with restricted access.

- Checked (

- Not checked (

If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>



) : Restricted

) : Accessible

setting.

If it is checked (



) in <Restricted Access>, a user can access the item only if the user has permission in <Group

Authority> setting.

Restriction on Network Access : Restricts remote access from a <Restricted Access> network.

•

- All Network : Restricts all access instances via Network Viewer and Web Viewer.

- Web Viewer : Restricts access via the Web Viewer.

Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of

•

time.

Permission Management

Admin

Restricted Access

Live View Backup Record Lock Search

PTZ Remote Alarm Out Shutdown All

Restriction on Network Access

All Network Web Viewer

Auto Log out 3 min

x

Manual Input of ID ON

x

Group

OK Cancel

User

Setup

English _37

Z6806127401A_SRD-470, 470D-IB_EN37 37Z6806127401A_SRD-470, 470D-IB_EN37 37 2010-04-30 오후 6:08:022010-04-30 오후 6:08:02

using the DVR

Manual Input of ID : Prompts you to enter the user ID

•

manually for the login process.

- Checked (
[½] symbols.
Use the virtual keyboard to enter the user ID.

When the permission setup is done, press <OK>.

6.

System Management

You can check the system version, update to a newer version, as well as data backup and initialization.

Checking the System Information

You can check the current system version, broadcasting system, MAC address. You can update the system.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <System Management>, and press [ENTER]
button.

Check the Version, Broadcast Format, and MAC Address.

4.

System Information : Shows the current system’s

•

information.
The values can not be changed by a user.

S/W Upgrade : Updates the DVR’s software up to date.

•

) : Encloses the registered user IDs with the

Login

ID

x

*****

Password

x

OK Cancel

System Management

System Information

System Information

Software Version V1.00h_100315180929

x

Broadcast Format

x

MAC Address 00:00:F0:54:FF:FF

x

S/W Upgrade

Device

x

Version

x

NTSC

Network

No S/W Data

Settings

Previous

Upgrade

Ex : If you connect to a storage device that has upgradable software



installed, and return to the <System Management> menu, the
current software version will be displayed.

System Management

System Information

System Information

Software Version V1.00h_100315180929

x

Broadcast Format

x

MAC Address 00:00:F0:54:FF:FF

x

S/W Upgrade

Device

x

Version

x

Settings

NTSC

v3.1.0.4

V1.00h_100320180929

Previous

Upgrade

38_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN38 38Z6806127401A_SRD-470, 470D-IB_EN38 38 2010-04-30 오후 6:08:052010-04-30 오후 6:08:05

Updating the Software

•

Connect a device storing the software to be updated.

1.

(It may take about 10 seconds to recognize the device.)

Upgradeable devices include USB memory, CD/DVD and



network device.

To update the network, the current DVR should have been



connected to the network.
Upgrade via the proxy server may not be enabled due to the

System Management

System Information

System Information

Software Version V1.00h_100315180929

x

System Upgrade

Broadcast Format

x

MAC Address 00:00:F0:54:FF:FF

x

Current Version V1.00h_100315180929
New Version V1.00h_100320180929

S/W Upgrade

Do you want to upgrade?

Device USB2FlashStorage

x

Version V1.08_090731170402

x

Settings

NTSC

OK Cancel

restricted access.

Select <System Management> from <System> window.

2.

Select <System Information>.

3.

When the recognized device appears, select <Upgrade>.

4.

The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is



Previous

same to or older than that of <S/W Upgrade>.

Press <OK> in the “System Upgrade” window.

5.

While updating, it shows the progress.



Updating progresses with 3 steps as shown in the fi gure.

•

System Management

System Information

System Information

Software Version V1.00h_100315180929

x

Broadcast Format

x

S/W Upgrade

MAC Address 00:00:F0:54:FF:FF

x

Software upgrading...

S/W Upgrade

Device USB2FlashStorage

x

Version V1.08_090731170402

x

Settings

NTSC

Upgrade

 USING THE DVR

Upgrade

When the updating is done, it automatically restarts.

6.

Do not turn the power off until it fi nishes restarting.

M

When you experience continued failure, consult the service

If “Upgrade Failed” appears, retry from the step 4.



center for assistance.

Previous

System Management

System Information

System Information

Software Version V1.00h_100315180929

x

Broadcast Format

x

S/W Upgrade

S/W Upgrade

MAC Address 00:00:F0:54:FF:FF

x

Software upgrading...

S/W Upgrade

Device USB2FlashStorage

x

Version V1.08_090731170402

x

Settings

NTSC

Software upgrading...

Do not turn off during the upgrade.

Previous

Upgrade

English _39

Z6806127401A_SRD-470, 470D-IB_EN39 39Z6806127401A_SRD-470, 470D-IB_EN39 39 2010-04-30 오후 6:08:082010-04-30 오후 6:08:08

using the DVR

Settings

You can copy and import the DVR settings by using a storage media.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <System Management>, and press [ENTER]
button.

Select <Settings>.

4.

A window of storage device and load factory default
appears.

Use direction buttons (

5.

◄ ►

item, and export or import settings data to a storage
device.

Storage Device : Shows the connected storage device.

•

Export : Exports DVR settings to the connected storage device.

•

Import : Imports DVR settings from the storage device and applies to the DVR.

•

If <Include Network Settings> is checked, the network settings will be imported too.



Load Factory Default : If <Default> is selected, a

•

confi rmation dialog for “Load Factory Default” prompts.
Press <OK> to initialize the system to the factory default.

To move to the previous menu, press <Previous>.

6.

) to move to a desired

System Management

System Information

Storage Device 1932 MB (Remained Capacity)

x

DVRUSB

x

USBDVR

x

Include Network Settings

Load Factory Default

x

System Management

System Information

Storage Device 1932 MB (Remained Capacity)

x

Load Factory Default

DVRUSB 38010100

x

USBDVR

x

Include Network Settings

Load Factory Default

x

10041400

Default

Sure to Default Setting?

OK Cancel

Default

Settings

Previous

Settings

Export

Import

Export

Import

Previous

Log Information

You can browse logs on the system and events.

System Log

System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.

4.

Select <System Log>.

Refer to “Using the Calendar”. (Page 33)



Click on the calendar <

Type : When there are too many logs, you can display logs of

•

> to display the calendar window.

the desired format by selecting the type.

Use direction buttons (

5.

◄ ►

) to move to a desired item,

and press <Search>.

Log Information

System Log

Search Day 2010-01-01

First Page

No. Log List Date/Time

Event Log

Last Page

Previous

Backup Log

Search

Type View all

Previous/Next Page

40_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN40 40Z6806127401A_SRD-470, 470D-IB_EN40 40 2010-04-30 오후 6:08:122010-04-30 오후 6:08:12

Event Log

Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.

Using the mouse may help make setup easier.

Use the up/down buttons () in <System> window to

3.

move to <Log Information>, and press [ENTER] button.
Select <Event Log>.

4.

Use direction buttons (

5.

◄ ►

) to move to the desired

item.

Set Search Day, Channel and Type and the press

6.

<Search>.

Refer to “Using the Calendar”. (Page 33)



Log Information

System Log

Search Day 2010-01-01

No. Log List Date/Time

7 Motion Detection [CH 1] 2010-01-01 00:02:14

6 Motion Detection [CH 2] 2010-01-01 00:02:14

5 Motion Detection [CH 3] 2010-01-01 00:02:14

4 Motion Detection [CH 4] 2010-01-01 00:02:18

3 Motion Detection [CH 3] 2010-01-01 00:02:18

2 Motion Detection [CH 2] 2010-01-01 00:02:18

1 Motion Detection [CH 1] 2010-01-01 00:02:18

First Page

Event Log

Last Page

CH All CHs Type View all

Previous

Backup Log

Search

Previous/Next Page

Click on the calendar < > to display the calendar window.

Backup Log

You can fi nd out who backed up and the details (backup time, channel, device to use, fi le format, etc.).

Using the mouse may help make setup easier.

In the <System> window, press the up/down () button

3.

to move to <Log Information> and press the [ENTER]
button.

Select <Backup Log>.

4.

Use the four direction buttons (

5.

◄ ►

) to move to a

desired item.
Specify a search term and select <Search> in the right

6.

corner.
Backup details for the search term will be listed.

Log Information

System Log

Search Day 2010-01-01 ~ 2010-01-02

First Page

No. User Date/Time

Event Log

Last Page

Backup Log

Previous/Next Page

Previous

Search

 USING THE DVR

English _41

Z6806127401A_SRD-470, 470D-IB_EN41 41Z6806127401A_SRD-470, 470D-IB_EN41 41 2010-04-30 오후 6:08:152010-04-30 오후 6:08:15

using the DVR

SETTING THE DEVICE

You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.

Camera

Setting the Camera

You can set Video, Audio, Channel Name and Dwell Time of a Camera.

Using the mouse may help make setup easier.

Press the [MENU] button on the remote control or front

1.

panel.

◄ ►

Use the left/right button (

2.

Device setting menu is selected.

Use the up/down buttons (

3.

and press [ENTER] button.

Select <Camera>.

4.

You will see a window where you can confi gure the
camera settings including Video, Audio, Channel Name,
Dwell Time and Progressive.

Use direction buttons (

5.

item, and set the value.

) to select <Device>.



) to move to <Camera>,

◄ ►

) to move to a desired

Camera

Camera

CH Video  Audio  CH Name SEQ-Dwell Time  Progressive

1 ON  OFF  CAM 01 5 sec  OFF

2 ON  OFF  CAM 02 5 sec  OFF

3 ON  OFF  CAM 03 5 sec  OFF

4 ON  OFF  CAM 04 5 sec  OFF

Device

Camera
Storage Device
Remote Device
POS Device
Monitor

PTZ

Logout

Exit











Video

•

- <ON/OFF> : You can turn ON/OFF the selected

channel’s camera.

- <Covert1> : Shows information other than the video of the selected channel.

For privacy protection, it does not display the video while the recording continues.



- <Covert2> : Shows nothing but an empty screen while the recording continues.

Audio

•

- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.

- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.

Audio output is available for only 1 channel.



CH Name : Up to 15 characters including blanks are allowed.

•

Refer to “Using Virtual Keyboard”. (Page 34)



SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.

•

If set to <OFF>, the channel is not listed in the Auto Sequence mode.



42_ using the DVR

Screen Setup

OK Cancel

Z6806127401A_SRD-470, 470D-IB_EN42 42Z6806127401A_SRD-470, 470D-IB_EN42 42 2010-04-30 오후 6:08:172010-04-30 오후 6:08:17

Progressive : You can set the progressive camera to ON/OFF.

•

If you set it to <ON> for the progressive camera, screen fl ickering will be reduced.



J

Screen Setup : The video appeared on the screen may vary

•

depending on the channel’s camera, confi gure the DVR
display to your preferences.
Select a channel and adjust the
<

(Contrast)>, and <(Color)> of the selected channel.

Press the <Init> to initialize settings back to the default 50.

•

When the camera setup is done, press <OK>.

6.

<

(Brightness)>,

Screen Setup

CH1 50 50 50

OK Cancel

Init Apply to All CH

Setting the PTZ

To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.
For other settings, refer to the “Remote Devices” settings. (Page 46)

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <Camera>, and press [ENTER] button.
Select <PTZ>.

4.

A window of PTZ settings appears.

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and select it.

ID : Set the ID of the connected camera of each channel.

•

You can easily setup by using the numeric buttons on the
remote control or front panel.

Protocol : Set the protocol of the connected camera of each

•

channel.

Camera

Camera

CH ID Protocol

1 0

2 1

3 2

4 3

PTZ

None

>

None

>

None

>

None

>

OK Cancel

 USING THE DVR











M

6.

(Page 65)

When the PTZ setup is done, press <OK>.

You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.



English _43

Z6806127401A_SRD-470, 470D-IB_EN43 43Z6806127401A_SRD-470, 470D-IB_EN43 43 2010-04-30 오후 6:08:192010-04-30 오후 6:08:19

using the DVR

Storage Device

You can check information on storage devices.

Confi rming Devices

You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD, CD/DVD).
Refer to “Product Specifi cations > Backup”. (Page 96)

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <Storage Device>, and press [ENTER] button.
Select <Device>.

4.

No. : Shows the assigned number of the internal HDD.

•

To see the detailed positioning of the HDD according to the



number, refer to <HDD Map>.

Used/Total : Shows the used/total capacity of the storage

•

device.
Usage : Sets the storage device’s usage.

•

-

USB memory and storage media such as CD/DVD are used for backup purpose only.

Status/Management : Shows the current status of the HDD, as in Normal/Check/Replace.

•

- Normal : Available to use

- Check : Available to use but recommended to replace

- Replace : Requires immediate replacement.

HDD Map : Shows the internal HDD’s locations according

•

to assigned numbers.

Refer to this for servicing or additional HDD installation.



Storage Device

Device

Device No. Used/Total Usage Status/Management

HDD 1 12.28G/499.37G Internal Normal

HDD Map

HDD Map

Format

OK Cancel

HDD Alarm

To move to the previous menu, press <OK>.

5.

44_ using the DVR

OK

<SRD-470>

HDD Map

OK

<SRD-470D>

Z6806127401A_SRD-470, 470D-IB_EN44 44Z6806127401A_SRD-470, 470D-IB_EN44 44 2010-04-30 오후 6:08:252010-04-30 오후 6:08:25

Formatting

You can format a storage device.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <Storage Device>, and press [ENTER] button.
Select <Format>.

4.

A window for selection of device for formatting appears.

5.

Use direction buttons (
formatted.

6.

Select <Format> on the bottom of the screen.
Press <OK> on the “Manage” confi rmation window will
start formatting the selected device.

7.

When the formatting is done, press <OK>.

◄ ►

) to select a device to be

Storage Device

Device

Device Select Used/Total Usage

HDD 1 12.28G/499.37G Internal

Format

Storage Device

Device

Device Select Used/Total Usage

HDD 1 12.28G/499.37G Internal

Format

Manage

Format

Format

HDD Alarm

OK Cancel

HDD Alarm

Formatting deletes all recordings.

Proceed formatting?

OK Cancel

OK Cancel

 USING THE DVR

HDD Alarm

You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.

4.

Select <HDD Alarm>.
A window for setting HDD check and replace output ports
and their durations appears.

5.

Use direction buttons (

◄ ►

) to move to the desired

item.

•

Alarm

- Alarm signal will output through the alarm out port on the

rear side when selected <1>, <2>.

- If <BEEP> was selected, a beep will sound.

- If <All> was selected, both beep sound and alarm signal through rear side ports will output.

•

Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specifi ed alarm
output port.

•

Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specifi ed
alarm output port.

Storage Device

Device

Check Alarm Output Port

x

Duration OFF

x

Replace Alarm Output Port

x

Duration OFF

x

Format

1 2 BEEP

All

1 2 BEEP

All

OK Cancel

HDD Alarm

English _45

Z6806127401A_SRD-470, 470D-IB_EN45 45Z6806127401A_SRD-470, 470D-IB_EN45 45 2010-04-30 오후 6:08:332010-04-30 오후 6:08:33

using the DVR

•

Duration : Sets the alarm duration for the alarm signal and beep sound.

- If <BEEP> was selected, a beep will sound.

- If <All> was selected, both beep sound and alarm signal through rear side ports will output.

<Check> status means that the HDD is operating but it has problems that require technical examination.



M

6.

Remote Devices

You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.

Using the mouse may help make setup easier.

3.

4.

5.

•

6.

(

) appears on the Live screen.

<Replace> status means that the HDD has defect and requires immediate replacement.



(

) appears on the Live screen.

When the HDD Alarm setup is done, press <OK>.

Use the up/down buttons () in <Device> window to
move to <Remote Device>, and press [ENTER] button.

Use direction buttons (

◄ ►

) to move to the desired

item, and press [ENTER] button.

Set the values of each communication setup of the remote

Remote Device

Baudrate Parity Data Stop Bit Transfer type

9600  None  8  1  Half Duplex

System Keyboard OFF ID 00

Remote Control ON ID 00

device.

Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.

Make sure to match IDs of the DVR, System Keyboard
and Remote Control, and press <OK>.

OK Cancel

For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 12)



M

POS Devices

You can set properties of POS devices connected to the DVR.
A POS device connection requires channel, preset, and Port/Ethernet settings.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <POS Device>, and press [ENTER] button.

Use direction buttons (

4.

item, and set the value.

POS USE : When selected <POS USE>, DVR and POS will

•

be connected.

J

the <POS USE> is not checked, the changes for POS device

If you change settings for the device and press <OK> while



will not be saved.

46_ using the DVR

◄ ►

) to move to a desired

POS Device

POS USE

POS CH Preset  Port/Ethernet

1 None No preset None

2 None No preset None

3 None No preset None

4 None No preset None

OK Cancel

POS Device Setup

Z6806127401A_SRD-470, 470D-IB_EN46 46Z6806127401A_SRD-470, 470D-IB_EN46 46 2010-04-30 오후 6:08:362010-04-30 오후 6:08:36

POS Device Setup : Sets the communication setups for the

•

POS device and DVR.

It is independent to the Remote Device setup.



POS Device

POS USE

POS CH Preset  Port/Ethernet

1 None No preset None

2 None No preset None

POS Device Setup

3 None No preset None

Baudrate Parity Data Stop bit Transfer type

4 None No preset None

9600  None  8  1  Half Duplex

OK Cancel

POS Device Setup

CH : Select the camera to be synchronized to the POS

•

device.

If selected a channel input fi eld, “Sync Channel Setup” window



appears.

One POS device can be synchronized to up to 4 cameras



(channels), however one channel cannot be synchronized to
multiple POS devices.

Channels to be synchronized to a POS device should be set to



“Event” in “Main Menu > Record > Recording Schedule”.
(Page 50)

Preset : Sets the name, start and end strings of the receipt

•

for the preset.

Preset name should be unique.



Use <Add> button to display “Add Preset” window, and set its



name, start string, and end string.

Port/Ethernet : Sets the port number for the DVR and POS

•

device connection.

COM1 : For RS-232C connections





7001~7016 : For Ethernet connections

OK Cancel

POS Device

POS USE

POS CH Preset  Port/Ethernet

1 None No preset None

Sync Channel Setup

2 None No preset None

3 None No preset None

4 None No preset None

POS Device

POS USE

Preset Setup

POS CH Preset Port/Ethernet

1 None No preset None

No. Name Start End Input char. Set Del

2 None No preset None

3 None No preset None

4 None No preset None

5 None No preset None

6 None No preset None

7 None No preset None

8 None No preset None

CH

Add Preset

Name

x

Start Keyword

x

End Keyword

x

1 2 3 4

OK Cancel

OK Cancel

OK Cancel

OK Cancel

OK Cancel

POS Device Setup

POS Device Setup

Previous/Next Page

 USING THE DVR

Add

When the POS Device setup is done, press <OK>.

5.

English _47

Z6806127401A_SRD-470, 470D-IB_EN47 47Z6806127401A_SRD-470, 470D-IB_EN47 47 2010-04-30 오후 6:08:382010-04-30 오후 6:08:38

using the DVR

Monitor

You can confi gure information to be displayed and its format for Spot Out monitor.

Setting the Monitor

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <Monitor>, and press [ENTER] button.
Select <Monitor>.

4.

Use direction buttons (

5.

◄ ►

item, and set the value.

Event Display : Sets the dwell time of the event channel

•

display on the monitor when an event occurs.
If selected <Continuous>, it displays the channel until you
press [ALARM] button to release it.

Display : Displays only checked items on the monitor

•

screen.
VGA : The current monitor may not display the video if the <VGA> settings do not match with this player

•

Sharpness : You can adjust the sharpness of the video output signal.

•

When the monitor setup is done, press <OK>.

6.

) to move to a desired

Monitor

Monitor

Event Display OFF

x

Display Date Time CH Name Icon

x

VGA 800x600

x

Sharpness Level1 (Low)

x

Display Position Setup

Spot Out

OK Cancel

Mode

Setting Display position

Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,
depending on the condition. Then, you can change the display position of the data.



In the <Device> window, press the up/down (

3.

to move to <Monitor> and press the [ENTER] button.
Select the <Monitor> item.

4.

Select <Display Position Setup> in the bottom.

5.

You will move to the <Display Position Setup> window.

Use the four direction buttons or the number buttons on

6.

the front panel or the remote control to adjust the data
position.

) button

Display Position Setup

30

30 30

30

OK Cancel

48_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN48 48Z6806127401A_SRD-470, 470D-IB_EN48 48 2010-04-30 오후 6:08:412010-04-30 오후 6:08:41

Setting the Spot Out

You can set the DVR to output information / video apart from the monitor out.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Device> window to

3.

move to <Monitor>, and press [ENTER] button.
Select <Spot Out>.

4.

The number of Spot Out terminals differs according to the



model.

Monitor

Monitor

Spot Out 1 SEQ

x

Spot Out

Mode

Set Mode

All

 USING THE DVR

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and set the value.

Spot Out 1 : You can select between Auto Sequence, and

•

Single.
Set Mode : A window for “Set Spot Out” appears and you

•

can set the channel for it.
You can set the dwell time between the screen switching in
“Setting the Device > Camera > SEQ-Dwell Time”.
(Page 42)

M

6.

Refer to “Spot Out”. (Page 29)

When the Spot Out is done, press <OK>.

You can setup using the mouse right button in Live screen.



Setting the Screen Mode

You can confi gure the Live screen and Split Screens.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.

4.

Select <Mode>.

5.

Use direction buttons (
item, and set the value.

•

Live Screen : Select split modes for the Live screen.
4-split screens are included by default.

•

Play Screen : Select split modes for the playback screen.
Single screen and 4-split screen are provided by default.

6.

When the screen mode setup is done, press <OK>.

◄ ►

) to move to a desired

OK Cancel

Monitor

Monitor

Spot Out 1 4-split

x

Monitor

Monitor Spot Out

Spot Out

Set Spot Out

1 2 3 4

OK

OK Cancel

Live Screen

Play Screen

OK Cancel

Mode

Set Mode

Mode

Live Play

English _49

Z6806127401A_SRD-470, 470D-IB_EN49 49Z6806127401A_SRD-470, 470D-IB_EN49 49 2010-04-30 오후 6:08:442010-04-30 오후 6:08:44

using the DVR

SETTING THE RECORDING

You can setup scheduled recording, event recording and other recording related settings.

Recording Schedule

Make your reservation on a date and time to schedule the recording on specifi ed time.

Using the mouse may help make setup easier.

Press the [MENU] button on the remote control or front

1.

panel.

◄ ►

Use the left/right button (

2.

Record menu is selected.

Use the up/down buttons (

3.

Schedule>, and press [ENTER] button.

Select <Recording Schedule>.

4.

A window of scheduled recording setup appears.

Use direction buttons (

5.

item, and set the value.

) to select <Record>.



) to move to <Recording

◄ ►

) to move to a desired

Recording Schedule
Event Record Duration
REC Quality & Resolution
Record Option

Recording Schedule

CH1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

All

Sun

Mon

Tue

Wed

Thu

Fri

Sat

Hol

No Recording Continuous Event Both(Cont&Evnt)

Record

Logout

Exit

Apply to All CH

Apply to All CH : If selected <Apply to All CH>, “Apply to

•

All CH” window appears.
Press <OK> to apply the setup to all channels.

When the recording schedule setup is done, press <OK>.

6.

50_ using the DVR

OK Cancel

Recording Schedule

CH1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

All

Sun

Apply to All CH

Mon

Tue

Wed

Thu

Fri

Sat

Hol

No Recording Continuous Event Both(Cont&Evnt)

Apply recording schedule to all channels?

OK Cancel

Apply to All CH

OK Cancel

Z6806127401A_SRD-470, 470D-IB_EN50 50Z6806127401A_SRD-470, 470D-IB_EN50 50 2010-04-30 오후 6:08:472010-04-30 오후 6:08:47

Recording Color Tags

Color Function Description

White No Recording No schedule / event recording

Orange Continuous Scheduled recording only

Blue Event Event recording only

Green Both(Cont&Evnt) Both scheduled / event recordings

Each press of a selected cell will cycle through <No Recording>-<Continuous>-<Event>­<Both(Cont&Evnt)>.

Event Record Duration

You can set the beginning and ending point of a recording on an event.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Record> window to

3.

move to <Event Record Duration>, and press [ENTER]
button.

Use direction buttons (

4.

◄ ►

) to move to a desired

item, and set the value.

Pre Event : The recording of an event will start at a

•

pre-determined time prior to the actual occurrence of the event.
If it is set to 5 seconds, the recording begins from 5
seconds before the event.

POST Event : The recording will continue for a

•

pre-determined time after the actual end of an event.
If it is set to 5 seconds, the recording ends in 5 seconds after an event.

Event Record Duration

CH Pre Event  POST Event

1 OFF

2 OFF

3 OFF

4 OFF

OK Cancel

1 min



1 min



1 min



1 min





 USING THE DVR









When the event recording duration setup is done, press <OK>.

5.

REC Quality / Resolution

You can set resolution, IPS, and quality of recordings by channel, and by recording type of standard / event.

Setting Standard Recording Properties

You can set each channel’s resolution, quality and IPS for normal recordings.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press
[ENTER] button.

4.

Select <Standard>.

5.

When the recording setup is done, press <OK>.

REC Quality & Resolution

Standard

CH Resolution  Record Rate  Record Quality

1 4CIF(L)  30ips  Level8(High)

2 4CIF(L)  30ips  Level8(High)

3 4CIF(L)  30ips  Level8(High)

4 4CIF(L)  30ips  Level8(High)

Event

OK Cancel











English _51

Z6806127401A_SRD-470, 470D-IB_EN51 51Z6806127401A_SRD-470, 470D-IB_EN51 51 2010-04-30 오후 6:08:502010-04-30 오후 6:08:50

using the DVR

Setting Event Recording Properties

You can set each channel’s resolution, quality and IPS for event recordings.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Record> window to

3.

move to <REC Quality & Resolution>, and press
[ENTER] button.

Select <Event>.

4.

Event recording setup window appears.

Use direction buttons (

5.

item, and select it.

•

Resolution : Sets the resolution of the recorded screen.

Resolution

Name Resolution Description

CIF(S) NTSC: 352 X 240, PAL: 352 X 288

2CIF(M) NTSC: 704 X 240, PAL: 704 X 288 Samples half of the horizontal screen.

4CIF(L) NTSC: 704 X 480, PAL: 704 X 576 Samples original screen size.

◄ ►

) to move to a desired

REC Quality & Resolution

Standard

CH Resolution  Record Rate  Record Quality

1 4CIF(L)  30ips  Level8(High)

2 4CIF(L)  30ips  Level8(High)

3 4CIF(L)  30ips  Level8(High)

4 4CIF(L)  30ips  Level8(High)

Event

OK Cancel

Samples each half of horizontal and
vertical screen.











Record Rate : Image Per Second, means the frames recorded per a second.

•

Record Quality : Sets the recording quality.

•

When the Event recording setup is done, press <OK>.

6.

Record Option

You can set the recording to stop or overwrite when the HDD is full.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Record> window to

3.

move to <Record Option>, and press [ENTER] button.

Use direction buttons (

4.

◄ ►

) to move to a desired

item, and set the value.

Disk End Mode : If selected <Overwrite>, recording will

•

continue despite the HDD full while overwriting the oldest.
If selected <Stop>, the recording will stop when the HDD is
full.

Disk End Beep : If selected <Stop>, the button is activated.

•

If you check it, the beep will sound on the disk full and the
recording stops.

Record Option

Disk End Mode Overwrite

x

Disk End Beep

Auto Delete

x

99 day

OK Cancel

52_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN52 52Z6806127401A_SRD-470, 470D-IB_EN52 52 2010-04-30 오후 6:08:522010-04-30 오후 6:08:52

Auto Delete : If you check it, Record Period setup is activated.

•

If you setup the auto delete, recorded data only in the confi gured period are searchable.

When the recording option setup is done, press <OK>.

5.

SETTING THE EVENT

You can set recording options for sensor, motion, and video loss event.

Sensor Detection

You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration.

Using the mouse may help make setup easier.

1.

Press the [MENU] button on the remote control or front
panel.

2.

Use the left/right button (

◄ ►

) to select <Event>.

Event setting menu is selected.

3.

Use the up/down buttons (



) to move to <Sensor

Detection>, and press [ENTER] button.

A window of sensor detection setup appears.

4.

Use direction buttons (

◄ ►

) to move to a desired

item, and set the value.

•

Sensor Operation : Sets the operation mode of sensors.

- <OFF> : Sensor does not operate.

- <N.O (Normal Open)> : Sensor is opened.
If the sensor is closed, it generates alarm.

- <N.C (Normal Close)> : Sensor is closed.
If the sensor is open by interruption, it generates alarm.

Cam : Select a channel to be connected to the sensor.

•

If selected camera, “Cam Preset setup” window appears.
Select a channel and setup the preset.

Preset setup can be done in PTZ mode.



Sensor Detection
Motion Detection
Video Loss Detection
Alarm Schedule

Sensor Detection

Sensor

Sensor Operation  Cam  Alarm  Duration

1 OFF  1 None 10 sec

2 OFF  2 None 10 sec

3 OFF  3 None 10 sec

4 OFF  4 None 10 sec

OK Cancel

Sensor Detection

Cam Preset setup

Sensor

Sensor Operation  Cam  Alarm  Duration

1 OFF  1 None 10 sec

CH  Preset

2 OFF  2 None 10 sec

1 None

3 OFF  3 None 10 sec

2 None

4 OFF  4 None 10 sec





Logout

Event

CH  Preset

3 None

4 None

 USING THE DVR

Exit

























OK Cancel

OK Cancel

English _53

Z6806127401A_SRD-470, 470D-IB_EN53 53Z6806127401A_SRD-470, 470D-IB_EN53 53 2010-04-30 오후 6:08:542010-04-30 오후 6:08:54

using the DVR

•

Alarm : Sets the alarm output method.

For further information on alarm output, refer to “HDD Alarm >



Alarm”. (Page

Duration : Sets the duration of alarm signal and alarm

•

45)

sound.

When the sensor detection setup is done, press <OK>.

5.

Motion Detection

You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Event> window to
move to <Motion Detection>, and press [ENTER] button.
A window of motion detection area setup appears.

4.

Use direction buttons (
item, and set the value.

•

Mode : Sets whether to activate motion detection.

•

Sensitivity : Sets the sensitivity level of the motion detection.

•

Alarm : Sets the alarm output method.

For further information on alarm output, refer to “HDD Alarm >



Alarm”. (Page

Alarm Duration : Sets the duration of alarm signal and alarm

•

45)

sound.

When the motion detection setup is done, press <OK>.

5.

◄ ►

) to move to a desired

Sensor Detection

Sensor

1 OFF  1 None 10 sec

2 OFF  2 None 10 sec

3 OFF  3 None 10 sec

4 OFF  4 None 10 sec

Motion Detection

CH Mode  Sensitivity  Alarm  Alarm Duration

1 OFF  Very High  None 10 sec

2 OFF  Very High  None 10 sec

3 OFF  Very High  None 10 sec

4 OFF  Very High  None 10 sec

Sensor Operation  Cam  Alarm  Duration

Alarm Setup

1 2 BEEP

All

OK Cancel

OK Cancel

OK Cancel



Motion Region



















Setting the Motion Detection Area

{

Select <Motion Region>.

|

When “Motion Region” window appears, select a
channel for detection and set the area of motion
detection.

•

To set the area in “Motion Region” window

In the “Motion Region” window, select desired region
from <

•

To set the area using <Individual> selection

In the “Motion Region” window, you can select cells
individually by using <Individual>.

When selected <Individual>, “Motion Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]

button on the remote control or front panel to display the “Motion Region” window again.

- Select : Selected cell is set to be a part of motion detection area.

- Unselect : Selected cell is removed from the motion detection area.

- Inverse : Unselected cells are set to be the motion detection area.

- Menu : After selecting individual motion areas, move to the “Motion Region” window.

If selected <Apply to All CH>, selected motion area is applied to all channels.



When the motion detection setup is done, press <OK>.

}

54_ using the DVR

>.

Motion Region

1 CH

Individual

OK Cancel

Apply to All CH

Select

Unselect

Inverse

Menu

Z6806127401A_SRD-470, 470D-IB_EN54 54Z6806127401A_SRD-470, 470D-IB_EN54 54 2010-04-30 오후 6:08:572010-04-30 오후 6:08:57

Video Loss Detection

You can set the alarm to be generated on a camera disconnection, which causes a video loss.

Using the mouse may help make setup easier.

Use the up/down buttons () in <Event> window to

3.

move to <Video Loss Detection>, and press [ENTER]
button.
A window of video loss detection area setup appears.

Use direction buttons (

4.

◄ ►

) to move to a desired

Video Loss Detection

CH Video Loss State  Alarm  Alarm Duration

1 OFF  None 10 sec

2 OFF  None 10 sec

3 OFF  None 10 sec

4 OFF  None 10 sec

item, and set the value.

Video Loss State : Sets whether to activate video loss

•

detection.
Alarm : Sets the alarm output method.

•

For further information on alarm output, refer to “HDD Alarm >



Alarm”. (Page

Alarm Duration : Sets the duration of alarm signal and alarm sound.

•

When the video loss detection setup is done, press <OK>.

5.

45)

OK Cancel

Alarm Schedule

You can set the conditions and operating hours for scheduled alarms.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Event> window to
move to <Alarm Schedule>, and press [ENTER] button.

4.

A window of <Alarm Schedule> settings appears.

5.

Alarm : Sets the alarm output method.

For further information on alarm output, refer to “HDD Alarm >



Alarm”. (Page

<ON> : Marked in orange, and always generates alarm on

•

45)

scheduled time.
<OFF> : Marked in white, no alarm is generated even if an

•

event occurs.
Event Sync : Marked in Blue, generates alarm only when an event occurs.

•

Apply to All Alarm : Applies the confi gured schedule to all

•

alarms.

When the alarm is generated on the scheduled time, you can



M

6.

stop the alarm by canceling the schedule.

When the Alarm Schedule setup is done, press <OK>.

Alarm Schedule

Alarm1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

All

Sun

Mon

Tue

Wed

Thu

Fri

Sat

Hol

OFF ON Event Sync

OK Cancel

Alarm Schedule

Alarm1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

All

Sun

Apply to All Alarm

Mon

Tue

Wed

Thu

Fri

Sat

Hol

OFF ON Event Sync

Apply the alarm scheduling to all?

OK Cancel

Apply to All Alarm

Apply to All Alarm











 USING THE DVR

OK Cancel

English _55

Z6806127401A_SRD-470, 470D-IB_EN55 55Z6806127401A_SRD-470, 470D-IB_EN55 55 2010-04-30 오후 6:09:052010-04-30 오후 6:09:05

using the DVR

BACKUP

You can check the backup device and set the backup schedule by channel or by time.
The product only supports external HDD of USB memory/DVD and USB type. (Page

Setting the Backup

You can backup the desired data to a connected device.

Using the mouse may help make setup easier.

1.

Press the [MENU] button on the remote control or front
panel.

2.

Use the left/right button (
Backup menu is selected.

3.

Press the [ENTER] button.
A backup window appears.
You can directly access it from the “Live screen menu”.
(Page

24)

4.

Use direction buttons (
item, and set the value.

•

Backup Range : Sets the <Start> and <End> time for the
backup.

•

Channel : Sets the channel to backup.
You can select multiple channels.

•

Device : Select a backup device from the recognized devices.
If the built-in internal CD/DVD or external USB CD/DVD is used for the backup, you can select the format of
recording between AVI and SEC.

Since SRD-470 model does not have built-in internal DVD Writer, internal CD/DVD backup is not available.



Type : Sets the backup data format.

•

- AVI : Saves the CODEC information provided by the DVR with the recording data, and saved data can be
played back by using external viewers (such as Windows Media Player) on a PC.

- DVR : Saved data can be played back only by the DVR.

- SEC : Saves data in the Samsung’s proprietary format with built-in viewer, which supports immediate
playback on a PC.

Filename : You can set the back fi le name.

•

Refer to “Using Virtual Keyboard”. (Page 34)



Check capacity : Shows the size of the selected backup data, used and available capacity of the selected

•

backup device.

Checking will stop if the backup size is over 200%.



Overlap : Shows a list of overlapping data on a same time according to the number of data.

•

It appears when one channel has multiple data on a certain time point due to changing of time or time zone
settings, etc.

Refer to time and time zone of “Setting the Date/Time/Language”. (Page 32)



◄ ►

) to select <Backup>.

◄ ►

) to move to a desired

Backup

Start x End

x

2010-01-01 00:01:06 ~ 2010-01-01 08:25:45

Device USB-Storage

x

Folder \20100101\

x

96)

Backup

1 2 3 4 ALL

Check capacity

OK Cancel

Logout

Backup

Type

x

Filename 0001

x

Exit

DVR

Change

Backup

Used

Free

56_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN56 56Z6806127401A_SRD-470, 470D-IB_EN56 56 2010-04-30 오후 6:09:082010-04-30 오후 6:09:08

5.

When the backup setup is done, press <OK>.

If no available device is recognized for backup, <OK> button is not activated.





J

The application may slow down during the backup.



You can switch to the menu screen during the backup in operation, but playback of data is not available.



When a CD/DVD or memory device is used for backup, it is not available to use the full capacity of the media since
the system consumes a part of its capacity.



If a CD or DVD media causes errors, the disc tray opens and closes a several times, and eventually backup process
will fail. In this case, replace the CD/DVD media and try again.



M

Pressing the <Exit> during the backup will return to the previous menu, while the backup progresses.

NETWORK CONFIGURATION

It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can confi gure the network environment which enables such functions.

Connection Mode

You can set the network connection route and protocol.

Setting the Connection

 USING THE DVR

Sets the protocol and environment of the network.

Using the mouse may help make setup easier.

Press the [MENU] button on the remote control or front

1.

panel.

Use the left/right button (

2.

◄ ►

) to select <Network>.

Network menu is selected.



3.

Use the up/down buttons (

) to move to <Connection

Mode>, and press [ENTER] button.

Select <Connection>.

4.

A window of connection mode setup appears.

Use direction buttons (

5.

◄ ►

) to move to a desired

item, and set the value.

Connection Mode : Sets the network connection mode.

•

Bandwidth : Sets the maximum data fl ow to be transferred.

•

(Upload speed)
Options will vary depending on the selected connection
mode.

- For <Static IP>, <Dynamic IP> : Select one from 50

kbps ~ 2Mbps, and Unlimited.

- For <ADSL>, select one from 50 kbps ~ 600 kbps.

Connection Mode
DDNS
Live Transfer
Mailing Service

Connection Mode

Connection

Connection Mode Static IP

x

Bandwidth 2Mbps

x

IP 192.168. 1.200

x

Gateway 192.168. 1. 1

x

Subnet Mask 255.255.255. 0

x

DNS

x

Protocol

Manual 168.126. 63. 1

OK Cancel

Logout

Exit

Network

English _57

Z6806127401A_SRD-470, 470D-IB_EN57 57Z6806127401A_SRD-470, 470D-IB_EN57 57 2010-04-30 오후 6:09:102010-04-30 오후 6:09:10

using the DVR

•

IP, Gateway, Subnet Mask, and DNS

- For <Static IP> : You can directly input IP address,

Gateway, Subnet Mask and DNS.

- For <Dynamic IP> : IP address, Gateway, and Subnet

Mask are set automatically.

- For <ADSL> : IP address, Gateway, and Subnet Mask

are set automatically.

User ID, Password : In case you selected ADSL, provide the

•

“User ID” and its “Password”.

DNS server for <Dynamic IP> and <ADSL> can be set by user only if you selected <Manual>.



M

When the connection setup is done, press <OK>.

6.

Setting the Protocol

Use the up/down buttons () in <Network> window to

3.

move to <Connection Mode>, and press [ENTER]
button.

Select <Protocol>.

4.

Use direction buttons (

5.

◄ ►

item, and set the value.

Protocol Type : Select the protocol type between TCP and

•

UDP.

If selected UDP, selections of Port (TCP), Port (UDP), and Unicast/



Multicast are activated.

Port (TCP) : Initially, <554~557> is set. It increases / decreases by 4.

•

- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet
environments.

•

Port (UDP) : Initially, <8000~8159> is set. It increases / decreases by 160.

- UDP : It has less stability and faster speed when compared to TCP, and recommended for local area
network (LAN) environments.

•

Unicast/Multicast : Select one between Unicast and Multicast.
If selected Multicast, Multicast IP and TTL are activated.

- Unicast : Transfers data (UDP, TCP) individually to each connecting client.

- Multicast : Multiple client can receive the data (only in UDP) without putting additional traffi c load to the
network.

•

Multicast IP : User can directly input.

•

TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.

•

Webviewer Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.

6.

When the protocol setup is done, press <OK>.

) to move to a desired

Connection Mode

Connection

Connection Mode ADSL

x

Bandwidth 600kbps

x

IP

x

Gateway

x

Subnet Mask

x

DNS Manual 168.126. 63. 1

x

User ID ID

x

Password

x

Connection Mode

Connection

Protocol Type TCP

x

Port(TCP) 554 ~

x

Port(UDP)

x

Unicast/Multicast

x

Multicast IP

x

TTL

x

Webviewer Port 80

x

Protocol

192.168. 1.200

192.168. 1. 1

255.255.255. 0

********

OK Cancel

Protocol

8000 ~ 8159

Unicast

224.126. 63. 1

5

OK Cancel

557

58_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN58 58Z6806127401A_SRD-470, 470D-IB_EN58 58 2010-04-30 오후 6:09:122010-04-30 오후 6:09:12

DDNS

You can set the DDNS site for a remote user’s network connection.

Using the mouse may help make setup easier.

3.

Use the up/down buttons () in <Network> window to
move to <DDNS>, and press [ENTER] button.

4.

Use virtual keyboard to enter user inputs.

Refer to “Using Virtual Keyboard”. (Page 34)





If selected <OFF> or <Samsung DDNS>, input fi elds are

DDNS

DDNS Site OFF

x

Host Name

x

User Name

x

User Password

x

********

deactivated.

When the DDNS setup is done, press <OK>.

5.

M

Refer to <DDNS Setting>. (Page 61)



OK Cancel

Connecting and Setting the Network

Networking may differ from the connection method, check your environment before setting the connection
mode.

When no router is used

Static IP mode

•

- Internet connection : Static IP ADSL, leased line, and LAN environments allows connection between the
DVR and remote user.

- DVR Network Settings : Set the <Connection Mode> in
<Connection> menu of the connected DVR to <Static IP>.

Consult your network manager for IP, Gateway and Subnet Mask.



Connection Mode

Connection

Connection Mode Static IP

x

Bandwidth 2Mbps

x

IP 192.168. 1.200

x

Gateway 192.168. 1. 1

x

Subnet Mask 255.255.255. 0

x

DNS

x

Protocol

Manual 168.126. 63. 1

 USING THE DVR

OK Cancel

Dynamic IP (DHCP) mode

•

- Internet connection : Connect the DVR directly to a cable modem, DHCP ADSL modem or FTTH network.

- DVR Network Settings : Set the <Connection Mode> in <Connection> menu of the connected DVR to
<Dynamic IP>.

ADSL (PPPoE: ID and password certifi cation)

•

- Internet connection : An ADSL modem is directly connected to the DVR, where the ADSL connection
requires user ID and password.

- DVR Network Settings : Set the <Connection Mode> in
<Connection> menu of the connected DVR to <ADSL>.

ADSL <User ID> and <Password> should be the same to the



ADSL user information.
If you don’t know the ID and password, consult your ADSL service
provider.

Connection Mode

Connection

Connection Mode ADSL

x

Bandwidth 600kbps

x

IP

x

Gateway

x

Subnet Mask

x

DNS Manual 168.126. 63. 1

x

User ID ID

x

Password

x

Protocol

192.168. 1.200

192.168. 1. 1

255.255.255. 0

********

OK Cancel

English _59

Z6806127401A_SRD-470, 470D-IB_EN59 59Z6806127401A_SRD-470, 470D-IB_EN59 59 2010-04-30 오후 6:09:142010-04-30 오후 6:09:14

using the DVR

When a router is used

To avoid IP address confl ict with the DVR's static IP, check followings :



J

Setting the DVR with a static IP

•

- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or
a router in a Local Area Network (LAN) environment.

Setting the DVR Network

•

Set the <Connection Mode> in <Connection> menu of the connected DVR to <Static IP>.

1.

Check whether the set IP address is in the static IP range provided by the IP router.

2.

IP, Gateway, and Subnet Mask : Consult your network manager.

Check whether the set IP address is in the static IP range provided by the IP router.



If a DHCP server is confi gured with starting address (192.168.0.100) and end address (192.168.0.200), you should



J

3.

•

1.

2.

- Once connected to the IP router, it prompts with password. While entering nothing to the User Name fi eld,

- Access the router’s DHCP confi guration menu and set its DHCP server activation, and provide the start and

set the IP address out of the confi gured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~

192.168.0.254).

Check the Gateway address and subnet mask are equal to those set in the IP router.

Setting the DHCP IP Address of the IP router

To access the IP router’s confi gurations, open a web browser on the local PC that is connected to the IP
router and enter the router’s address (ex : http://192.168.1.1).

At this stage, make the local PC's windows network confi gurations to the below example :
Ex) IP : 192.168.1.2

Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1

enter “admin” into the password fi eld and press <OK> to access the router confi gurations.

end address.
Set the start address (192.168.0.100) and end address (192.168.0.200).

Above steps may differ from the router devices depending on the manufacturer.



M

Setting Router’s Port Forwarding

•

Set the protocol to <TCP>.

1.

External Port Range : Enter the TCP Port set in the

2.

<Port(TCP)> in <Protocol> menu of the connected DVR.
If more than one DVRs are connected to the router, the
TCP port can be different.

Internal PC IP Address : Enter the IP address set to the

3.

Connection Mode

Connection

Protocol Type TCP

x

Port(TCP) 554 ~

x

Port(UDP)

x

Unicast/Multicast

x

Multicast IP

x

TTL

x

Webviewer Port 80

x

Protocol

8000 ~ 8159

Unicast

224.126. 63. 1

5

557

<IP> in <Connection> menu of the connected DVR.
Internal Port Range : Set the same to the “External Port

4.

M

Range”.

Above steps may differ from the router devices depending on the manufacturer.



Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s

OK Cancel

network.

60_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN60 60Z6806127401A_SRD-470, 470D-IB_EN60 60 2010-04-30 오후 6:09:172010-04-30 오후 6:09:17

DDNS Setting

DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the fl oating IP address with the DDNS
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP
system.

Setting DDNS in the DVR

•

Set <Protocol Type> in the <Protocol> menu of the connected DVR to the following :
Ex) Protocol Type : TCP

Port (TCP) : 0554,0555,0556,0557
DDNS Site : Samsung DDNS

DDNS Settings of the Router

•

Select the corresponding menu for the network transfer protocol of the router.

Live Transfer

Sets the quality of the image that is transferred from the DVR to the network.

Using the mouse may help make setup easier.

3.

In the <Network> setting window, press the up/down
() button to move to <Live Transfer> and press the
[ENTER] button.
The Live Transfer window appears.

4.

Use the direction buttons (

◄ ►

) to move to a desired

item and set the value.

5.

When the live transfer is done, press <OK>.

For the resolution of the live transfer, refer to “Resolution”.



(Page 52)

Live Transfer

Resolution CIF(S)

x

Quality Low

x

OK Cancel

 USING THE DVR

English _61

Z6806127401A_SRD-470, 470D-IB_EN61 61Z6806127401A_SRD-470, 470D-IB_EN61 61 2010-04-30 오후 6:09:182010-04-30 오후 6:09:18

using the DVR

Mailing Service

You can send an e-mail to a DVR-registered user at a specifi c time interval, or if an event occurs.

If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set



M

SMTP Setting

Sets the SMTP mail server.

Using the mouse may help make setup easier.

3.

4.

5.

•

•

•

•

•

•

•

•

•

6.

to <OFF>, only the text notifi cation will be sent to the applicable email address.

In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.

Select <SMTP>.
You will see the SMTP setting window.

Use direction buttons (

◄ ►

) to move to a desired item

and set the value.

ServerType : Displays the connected server type.

Mailing Service

SMTP

ServerType SMTP mail Server

x

Server

x

Port 25

x

User

x

Password

x

Secure Transfer Never

x

Sender ex. [e-mail]

x

TEST

Event

Use Authentication

********

Server : Enter a server to connect to.
Port : Sets the communication port.
Use Authentication : Check this if the SMTP server uses user authentication.

The account input box will be activated.
User : Enter a user to use authentication when connecting to the SMTP server.
Password : Enter the password of the SMTP server user.
Secure Transfer : Select one from <Never> and <TLS (if available)>.
Sender : Use the virtual keyboard to enter the sender’s e-mail address.

Refer to “Using Virtual Keyboard”. (Page 34)



TEST : Conducts the test on the server settings.

When the SMTP setting is done, press <OK>.

.

OK Cancel

Group Recipient

Event Setting

You can set the interval and type of the event that will be sent to the user.

Using the mouse may help make setup easier.

In the <Network> setting window, press the up/down

3.

() button to move to <Mailing Service> and press the
[ENTER] button.

Select <Event>.

4.

Use direction buttons (

5.

◄ ►

) to move to a desired item

and set the value.

•

Event Interval : Set the event interval.

If a series of events occurs, the e-mail will be sent at the specifi ed



interval, not on each event.

Use Event Transfer : Select an event type to send if an event occurs.

•

If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.

When the event setting is done, press <OK>.

6.

62_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN62 62Z6806127401A_SRD-470, 470D-IB_EN62 62 2010-04-30 오후 6:09:202010-04-30 오후 6:09:20

Mailing Service

SMTP

Event Interval 10 min

x

x

Use Event Transfer

Event

Sensor Motion

Change P/W HDD Info Video Loss

Power On/Off Manual Record

Group

OK Cancel

Recipient

Group Setting

You can set the group to whom the e-mail is sent, and specify the permission for each group.
You can add recipients for each group in the <Recipient> menu item.
The recipient is set separately from the DVR user group.

Using the mouse may help make setup easier.

In the <Network> setting window, press the up/down

3.

(



) button to move to <Mailing Service> and press the

[ENTER] button.

4.

Select <Group>.

5.

Use direction buttons (

◄ ►

) to move to a desired item

Mailing Service

SMTP

Group

x

x

Recipient Permission

Sensor Motion

Change P/W HDD Info Video Loss

Power On/Off Manual Record

Event

Group

Add Delete Rename

and set the value.

Add : Select <Add> and use the virtual keyboard to add a

•

group.

Refer to “Using Virtual Keyboard”. (Page 34)



Delete : Deletes the selected group.

•

Rename : You can reset the recipient permission of an existing group.

•

Recipient Permission : Set the permission of the recipient group.

•

When the group setting is done, press <OK>.

6.

OK Cancel

Recipient Setting

Recipient

 USING THE DVR

You can add a user to the group or delete him/her from the group, or change the group.

Using the mouse may help make setup easier.

3.

In the <Network> setting window, press the up/down
() button to move to <Mailing Service> and press the
[ENTER] button.

4.

Select <Recipient>.

5.

Use direction buttons (

◄ ►

) to move to a desired item

Mailing Service

SMTP

Group

x

Group Name e-Mail Address Delete

Event Group

All Group

and set the value.

OK Cancel

•

Add : You can select a recipient name, e-mail address or
group.
You should have created a group in the <Group> menu
item before you can add a user to the group.

Refer to “Using Virtual Keyboard” for input of the user name and



the e-mail address. (Page 34)

When the recipient setting is done, press <OK>.

6.

Mailing Service

SMTP

Group ABC

x

Group Name e-Mail Address Delete

Event Group

Add recipient

Name

x

Email

x

Select Group ABC

x

OK Cancel

OK Cancel

Recipient

Add

Previous/Next Page

Recipient

Add

Previous/Next Page

English _63

Z6806127401A_SRD-470, 470D-IB_EN63 63Z6806127401A_SRD-470, 470D-IB_EN63 63 2010-04-30 오후 6:09:222010-04-30 오후 6:09:22

using the DVR

CONTROLLING A PTZ DEVICE

The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference.

PTZ Device

The PTZ device can be activated only if a channel in connection with the PTZ camera is selected.

Getting started with PTZ

The PTZ camera is available, only if a channel is selected, in the following way :



Using the button on the remote control or the front panel
Select the [PTZ] button on the remote control or the front panel.



Using the launcher menu

PTZ

Click PTZ <

Using the right-click menu in Live mode



> to display the live launcher.

Right-click any area on the screen to display the context menu, and
select <PTZ Control>.

Using icons on the live screen



Click the PTZ <

> icon on the live screen.

Scene Mode

Spot Out

PTZ Control

ZOOM

Audio

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Logout

PTZ Alarm Freeze









M

The PTZ function is available only if the PTZ camera is
connected so that the PTZ icon is displayed on the screen.

Using the PTZ camera

You can use one camera to perform all functions of PAN, TILT and ZOOM for monitoring multiple places and
set the preset to your preference in a desired mode.

1.

Launch the <PTZ Control> menu.
As the PTZ <
yellow, you access the “PTZ Control” mode to display the
“PTZ Control” menu.

Use direction keys in the launcher menu or use direction

2.

buttons (

◄ ►

to move the target area to record.

•

PTZ Wheel : Clicking a nearer point to the center will move
in that direction slowly; clicking a farther point from the
center will move fast.



Keep clicking left to rotate the lens counter clockwise; keep clicking right to rotate the lens clockwise.

Zoom : You can use the Zoom function of the PTZ camera.

•

IRIS : Adjusts the intensity of radiation incoming to the iris.

•

> icon on the bottom right corner turns

) on the remote control or the front panel

PTZ Control CAM01

Auto Pan

Scan

Pattern

Preset

Select

Select

Select

Select

Exit

Camera Setup

Select Preset

Save Rename

Delete Delete All

Delete Delete All

64_ using the DVR

Z6806127401A_SRD-470, 470D-IB_EN64 64Z6806127401A_SRD-470, 470D-IB_EN64 64 2010-04-30 오후 6:09:252010-04-30 오후 6:09:25

Focus : Enables you to adjust the focus manually.

SAMSUNG PROTOCOL

ADDR 0
TYPE RS-485,HALF
BAUD 9600
LENS OK!
TILT OK!
PAN OK!

**

MAIN MENU

**

...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
CLOCK SET...
SYSTEM INFO...

•

•

Auto Pan : The camera automatically runs between the two points that you selected.

•

Scan : The camera moves to the preset points in the specifi ed sequence.
If multiple presets are specifi ed, the PTZ camera will automatically move to all of the preset points one at a
time.

•

Pattern : Makes the PTZ camera remember and follow the past route.

The functions of Auto Pan, Scan and Pattern are supported in the protocols of Samsung, Panasonic and Pelco, and are



different in terms of the name and setting, depending on the protocols of Samsung, Panasonic and Pelco.
(Panasonic : Auto Pan, Sequence, Sort / Pelco : Auto Pan, Frame Scan, Pattern)

M

(Page

43)

Before entering the PTZ device control mode, set the values of the PTZ device in the <Setting the PTZ> menu.



Preset Setting

A preset is a set of specifi c target points of a PTZ camera, and up to 20 presets per a camera can be stored.

Using the mouse may help make setup easier.

In PTZ Control mode, use the direction buttons to adjust the camera in a desired direction.

1.

Select the <Save> key.

2.

The virtual keyboard for inputting the preset will appear.

Refer to “Using Virtual Keyboard”. (Page 34)



Save : You can save the preset settings.

•

Rename : You can change the settings of the existing presets.

•

Delete : Deletes the selected preset.

•

Delete All : Deletes all existing presets.

•

 USING THE DVR

M

3.

accordingly.

Press <OK>.

If you replace the camera of the channel that stores the preset list with a new one, you should reset the preset



The preset will be saved as a name that you entered.

Camera Setting

A PTZ camera has its own menu system. Optimize the PTZ camera according to the DVR.

Using the mouse may help make setup easier.

Connect the PTZ camera to the DVR and run the PTZ

1.

camera again to display the camera’s protocol setting
window.

Check the protocol ID of the camera.

2.

In “Device > Setting the PTZ”, enter the PTZ camera ID in the



ID input box of the channel that is connected to the PTZ camera.
(Page

43)

Select <Camera Setup> in the PTZ Control menu.

3.

The camera-specifi c menu appears.

You can confi gure the settings of only those cameras that support



the protocols of Samsung, Pelco D/P, AD and Panasonic.

If you are setting Auto Pan or Pattern in the camera menu, press



and hold the appropriate button for a certain time so that the button
operation can be different from that in normal PTZ setting.

SAMSUNG PROTOCOL

ADDR 0
TYPE RS-485,HALF
BAUD 9600
LENS OK!
TILT OK!
PAN OK!

MAIN MENU

**

CAMERA SET

Camera Setup



Exit

VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
CLOCK SET...
SYSTEM INFO...

**

...

English _65

Z6806127401A_SRD-470, 470D-IB_EN65 65Z6806127401A_SRD-470, 470D-IB_EN65 65 2010-04-30 오후 6:09:372010-04-30 오후 6:09:37

search & play

SEARCH

You can perform the search for recorded data by the time or by the search criteria such as an event.
You can access the <Search> menu directly in Live mode.

1.

In Live mode, right-click any area of the screen.
The Live menu appears.

2.

Select <Search>.
Or, press the [SEARCH] button on the remote control or
the front panel.

3.

The Search menu appears.

If you have not checked “POS USE” in the “Main Menu >



Device > POS Device” menu, the Search menu does not
include the “POS Search” item. (Page 46)

The search can be restricted by the Auto Delete function.

4.

Refer to “Setting the Recording > Record Option”.
(Page 52)

Time Search

Event Search

Backup Search

POS Search

Motion Search

Return

Scene Mode

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Logout





M

data on a certain time, produced due to the change of DVR’s

Overlapped data : It only appears if there exists overlapped



time setup. The latest data comes fi rst, from <List0>.
It does not appear in <Backup Search>.

Time Search

You can search for recorded data of a desired time.
As the time to display may be different depending on the time zone and the DST standard time, the time of
data recorded in the same time can be displayed differently depending on time zone and DST settings.

Using the mouse may help make setup easier.

Select <Time Search> in the <Search> menu.

4.

Select a date to search.

5.

Refer to “Using the Calendar”. (Page 33)



The record data on the specifi c date will be listed.

6.

The display bar is different according to the data type.
So check the data type for the color in the left pane.

Use direction buttons (

7.

◄ ►

) to set the search criteria

and press the [ENTER] button.

Go to First : Moves to the earliest date.

•

Go to Last : Moves to the most recent date.

•

Time : Enter a time to perform the search or use the up/down button <

•

Time Search

2010-01-01

2010/01/01 00:01:17

Standard Schedule

Motion Sensor

V.Loss Etc

>

> to select one.

Go to First Go to Last

Overlapped Data List1

00:01

All Data

CAM 01

CAM 02

CAM 03

CAM 04

Play Return

Zoom In Zoom Out

Previous/Next Page

66_ search & play

Z6806127401A_SRD-470, 470D-IB_EN66 66Z6806127401A_SRD-470, 470D-IB_EN66 66 2010-04-30 오후 6:09:482010-04-30 오후 6:09:48

Zoom In : The map enlarges in detail.

•

It will switch in the sequence of 24 hours - 4 hours - 1 hour

- 5 minutes.
Zoom Out : The map will switch in the reverse order of the

•

detailed mode above.
It will switch in the sequence of 5 minutes - 1 hour - 4 hours

- 24 hours.

Double-click a desired time to zoom it in/out.



M

Preview : Click <Channel> and select (click, drag) a time in

•

Time Search

2010-01-01

2010/01/01 00:01:17

Standard Schedule

Motion Sensor

V.Loss Etc

Go to First

Overlapped Data List1

00:01

All Data

CAM 01

CAM 02

CAM 03

CAM 04

Play Return

<Duration> to display a still image for the portion.

- If the selected channel does not contain any recorded data, it will be marked black.

Select a data item and click <Play>.

8.

The screen switches to the data playback mode.

Event Search

You can search for events by the channel and play them.

Using the mouse may help make setup easier.

Select <Event Search> in the <Search> menu.

4.

Use direction buttons (

5.

◄ ►

) to set the search criteria

and press the [ENTER] button.

All record events on a specifi c date will be found. (Normal/



Schedule recording included)

Date/Time Preview : If you select a data item in the list, the

•

still image of the selected data will be displayed in the left
preview pane.

Event : Displays the type of the event that occurred.

•

Select a data item and click <Play>.

6.

The screen switches to the event data playback mode.

Event Search

CAM 01

2010-01-01

Overlapped Data List1

2010/01/01 00:01:22

No. Date/Time Preview Event

3 02:47:54 ~ 02:48:59 Motion

2 00:39:06 ~ 00:40:30 Motion

1 00:01:22 ~ 00:02:28 Motion

Play Return

Go to Last

Zoom In Zoom Out

Previous/Next Page

 SEARCH & PLAY

Go to First Go to Last

Previous/Next Page

Backup Search

Searches for backup data in the connected backup device.
Only data in the format of DVR is included in the search.
Refer to <Type> in “Backup > Setting the Backup”. (Page 56)

Using the mouse may help make setup easier.

4.

Select <Backup Search> in the <Search> menu.

5.

Use direction buttons (

◄ ►

) to set the search criteria

and press the [ENTER] button.

Record Period : Displays the record period.

•

Channel : Displays the recorded channel.

•

Play Start Time : Select a time that you start playing.

•

Select a data item and click <Play>.

6.

The screen switches to the backup data playback mode.

Z6806127401A_SRD-470, 470D-IB_EN67 67Z6806127401A_SRD-470, 470D-IB_EN67 67 2010-04-30 오후 6:09:532010-04-30 오후 6:09:53

Backup Search

No. Folder Name File Name

1 20100101 16190000

File Name 16190000 x Channel 1

x

Record Period 2010-01-01 01:01:01 - 2010-01-01 01:01:10

x

Play Start Time 2010-01-01

x

USB:USB2FlashStorage

Previous/Next Page

01:01:01

Play Return

English _67

search & play

POS Search

You can search for data in the POS device that is connected to the DVR.

You can use the mouse to select the related items.

Select <POS Search> in the <Search> menu.

4.

Use direction buttons (

5.

◄ ►

and press the [ENTER] button.

You can enter specifi c text to refi ne your search.



Keyword : Use the virtual keyboard to enter a keyword.

•

Search Criteria :

•

- <Case Sensitive> : If selected, search will be performed

case-sensitively.

- <Whole Word> : If selected, only the exact matches with

the keyword will be found.

Preview : Select a data item in the list to display the preview image.

•

Information about the image will be displayed on the bottom of the screen.

•

6.

: You can use these buttons to accelerate your search if you have a huge list of search results.

Select a data item and click <Play>.
The screen switches to the POS data playback mode.

) to set the search criteria

POS Search

Date/Time 2009-12-25 03:41:18 2010-01-01 03:41:18

Keyword Case Sensitive Whole Word

Overlapped Data List1

2010/01/01 03:41:15

CHANGE

5.95

Go to First Go to Last

POS CH Start Date/Time Keyword

1 1 2010-01-01 03:41:15 CHANGE _

1 1 2010-01-01 03:41:15 CASH _

1 1 2010-01-01 03:41:10 CASH _

Previous/Next Page

Play Return

Search

Motion Search

If a motion is detected in each channel, you can set a desired area to perform the search.

You can use the mouse to select the related items.

4.

Select <Motion Search> in the <Search> menu.

5.

Use direction buttons (

◄ ►

) to set the search criteria

and press the [ENTER] button.

If you set the motion area to <Manual Area>, the <Setup>



button will be activated.

Motion Region : Select an area to perform the search.

•

- All Area : Searches for all areas of the selected channel.

- Current Area : Searches for the motion area for each

channel specifi ed in “Motion Detection >
Setting the Motion Detection Area”. (Page

54)

- Manual Area : You can set the motion area manually.

Setup : The Setup button will be activated only if you have

•

set the motion area to Manual. Press this button to display
the area setting window.

Date/Time : The Date/Time will be automatically set by the

•

hour, and the end time will be automatically set to one hour
later than the start time if it is set.

Preview : Select a data item in the list to display the still

•

image of the item.

Motion Search

Channel CAM 01 Motion Region All Area

Date/Time 2010-01-01 03:41:18 2010-01-01 05:11:44

No. Start Time

7 01:01:30

6 01:01:25

5 01:01:20

4 01:01:15

2010/01/01 01:01:30

3 01:01:10

2 01:01:05

1 01:01:01

Motion Region

1 CH

Play Return

OK Cancel

Individual

Go to First Go to LastOverlapped Data List1

Apply to All CH

Setup

Search

Previous/Next Page

Select a data item and click <Play>.

6.

The screen switches to the motion data playback mode.

68_ search & play

Z6806127401A_SRD-470, 470D-IB_EN68 68Z6806127401A_SRD-470, 470D-IB_EN68 68 2010-04-30 오후 6:09:562010-04-30 오후 6:09:56

PLAYBACK

Play

You can play data stored in the HDD and backup a desired portion of the data.

Using the mouse may help make setup easier.

In Live mode, click <Play> in the right-click menu or

1.

< > in the launcher menu, or press the Play button on
the remote control or the front panel.



Use the up/down button (

2.

For data search, refer to <Search>. (Page 66)



Select a data item and click <Play> in the Search menu.

3.

The selected data is played and the play launcher appears
on the screen.

If there is an existing data, <Play> will start immediately without



performing the search.

: You can play up to 4 channels in real time.

•

- In a split mode, the real time playback may not be
supported, depending on the record quality, resolution
and number of channels. And some frame rates may be
supported.

Playback Information : Displays the date and time of the current data in the top corner.

•

Mode Switch : Select a desired play mode, or press the [MODE] button to switch the screen mode to

•

4-split and Single in that sequence.

The default channel of the Live mode is CH1, which can be changed later.



: Switches to Live mode.

•

REC

•

Play Time : Displays the time and date of the current video.

•

Play Bar : Displays the time of recorded data in the selected channel for the past 24 hours; the red gridline

•

: Records all channels in Live mode.

indicates the current play time.

) to select a menu.

Scene Mode

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Search

Backup

Main Menu

Shutdown

Hide Launcher

Logout

PTZ Alarm Freeze





REC

 SEARCH & PLAY

Speed : Supports various speed options of x1, x2(-2), x4(-4), x8(-8), x16(-16), x32(-32) and x64(-64).



M



Slow : Supports slow speed options of x1/2(-1/2), x1/4(-1/4) and x1/8(-1/8).

Backup : Click < > to set the current time to the start

•

time of backup; you can specify a backup area using the
mouse (yellow triangle).
Click < > again to set the current time to the end time of
the backup and the “Backup Range” window appears.

- Type : Supports formats of DVR, AVI and SEC.

Refer to a list of formats in “Setting the Backup”.
(Page 56)

Backup Range

Start x End

x

2010-01-01 00:01:06 2010-01-01

Device

USB Storage x Type DVR

x

Folder \20100101\ x Filename 0001

x

Check capacity

Backup Cancel

Backup

Used

Free

01:10:25

Change

- Device : Select a backup device.

- Check Capacity : Enables you to check the capacity of the
selected storage device.

If you want to return to the Live screen in Play mode, click <

4.

> in the launcher menu or press the

[] button on the remote control or the front panel.

English _69

Z6806127401A_SRD-470, 470D-IB_EN69 69Z6806127401A_SRD-470, 470D-IB_EN69 69 2010-04-30 오후 6:10:062010-04-30 오후 6:10:06

web viewer

INTRODUCING WEB VIEWER

What is Web Viewer?

Web Viewer allows remote access to your DVRs. You have
access to live video, archived video, PTZ control (if confi gured),
etc.

PRODUCT FEATURES

•

Remote access from a standard browser

•

Supports PTZ camera controls

•

Supports 1, 4 camera viewing formats (maximum of
cameras in the list).

•

Gets JPEG,
or Save JPEG, BMP format images”.

•

Record video in AVI format-compatible with popular media players. (needed the Xvid codec)

BMP format images to print and save to “Print

SYSTEM REQUIREMENTS

The following lists the minimum suggested hardware and operating system requirements needed to run the
Web Viewer.

Windows XP Professional

OS

Windows 2000
Windows Vista Home Basic /Premium
Windows 7

4

Web Browser Internet Explorer 6.0.2900.2180 or higher

CPU Intel Pentium 4.2 GHz

Memory 512 MB

Monitor High Color 16-bit 1024 x 768

50 MB(Installation space required)

HDD

* Additional HDD space required for recording.

Recorded fi le size will vary depending on recording quality settings.

70_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN70 70Z6806127401A_SRD-470, 470D-IB_EN70 70 2010-04-30 오후 6:10:172010-04-30 오후 6:10:17

CONNECTING WEB VIEWER

Open your web browser and type the IP address or URL

1.

of DVR into the URL address box.

The basic URL of the DVR is as following in case of MAC

M

address :

00-00-F0-ab-cd-ef : nabcdef.websamsung.net



00-16-6c-ab-cd-ef : mabcdef.websamsung.net



00-68-36-ab-cd-ef : pabcdef.websamsung.net



You can also use registered URL which setups up in the Setup menu of your DVR.



Set the Admin ID and password same to those of the DVR

2.

Admin.
For general users, enter the DVR user ID and password.

It allows up to 10 simultaneous access including the Admin



M

and general users.

It does not allow multiple login of the Admin user.



Initial password of the Admin user is set to “4321”.



Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.





Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the
Web Viewer. (Page



All settings are applied by the DVR’s settings.

37)

 WEB VIEWER

Click <Install ActiveX Control…>.

3.

Click <Install>.

4.

Click <Install>.

5.

English _71

Z6806127401A_SRD-470, 470D-IB_EN71 71Z6806127401A_SRD-470, 470D-IB_EN71 71 2010-04-30 오후 6:10:182010-04-30 오후 6:10:18

web viewer

You may have “Windows Security Alert” that attempts to

6.

block this with the Windows Firewall. In that case, click
<Unblock> to start Web Viewer.

7.

Installation is complete.
Now you can see the main screen of Live Viewer.

72_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN72 72Z6806127401A_SRD-470, 470D-IB_EN72 72 2010-04-30 오후 6:10:212010-04-30 오후 6:10:21

USING LIVE VIEWER

 WEB VIEWER

The Live Viewer screen consists of following :

This displays the IP address and the model name of the connected DVR.

These menus consist of <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.

These buttons are used for the screen split and full screen mode.

Shows the IP address and model name of the connected DVR.

Select <DVR Time> or <PC Time> for the OSD time information display setting of the Live Viewer.

These buttons are used for sequence and changing the screen channel.

These buttons are used for capture, print, and save the image.

Shows the channel of the connected DVR.

These buttons are used for PTZ related functions.

This displays the screen for connected camera with DVR.

The resolution is set to 1024X768 pixels.



M

The initial split-screen mode is set according to the number of channels connected to DVR. You can change the



split-screen mode by clicking buttons for split-screen modes.

English _73

Z6806127401A_SRD-470, 470D-IB_EN73 73Z6806127401A_SRD-470, 470D-IB_EN73 73 2010-04-30 오후 6:10:242010-04-30 오후 6:10:24

web viewer

OSD INFORMATION DISPLAY

The channel number, video size, and IP address of the connected

DVR are displayed.

The current date and time will be displayed according to the

selected time information display setting <DVR Time> or <PC
Time>.

Alarm icon appears when alarm is issued.

It disappears when pressed the [ALARM] button of the DVR.

Motion icon appears when motion is detected.

It disappears when pressed the [ALARM] button of the DVR.

It displays whether the PTZ controls are active.

If you have set PTZ cameras for the DVR, “PTZ” is displayed on the



M

SPLIT-SCREEN

You can change the split mode by clicking each number icon.

screen. Select a PTZ camera channel and use the [PTZ] button for
camera control.

SINGLE MODE QUAD MODE

•

Click <
The screen displays the selected camera connected to the DVR in
“SINGLE MODE”.

Click <

•

The screen displays the selected camera connected to the DVR in
“QUAD MODE”.

Click <

•

The screen displays the selected camera connected to the DVR in
“FULL SCREEN MODE”.
Double clicking on the screen or pressing any button of the keyboard
returns to the previous mode.

> button.

> button.

> button.

74_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN74 74Z6806127401A_SRD-470, 470D-IB_EN74 74 2010-04-30 오후 6:10:272010-04-30 오후 6:10:27

CONNECTED DVR

This displays the IP address and the status of the connecting DVR.

Connection failure message



M

No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.



The number of simultaneous connections are limited to 10.

Setting the display of the OSD time information

Select <DVR Time> or <PC Time> for the OSD time information display
setting.

DVR Time : Based on the time of the connected DVR

•

PC Time : Based on the time of the PC currently running the Web Viewer.

•

 WEB VIEWER

CHANGING THE LIVE SCREEN MODE

4-split mode does not support “SEQUENCE”, “PREVIOUS” and “NEXT”.



SEQUENCE : When this button is clicked, screens are switched at a

•

preset interval.
In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
In QUAD MODE, the screen refreshes at the preset interval.

Preset interval (10 seconds)



PREVIOUS : When this button is clicked, the previous screen appears.

•

In QUAD MODE, the screen is refreshed.

NEXT : When this button is clicked, the next screen appears.

•

In SINGLE MODE, the channel numbers are sequentially switched from
1 to 4.
In QUAD MODE, the screen is refreshed.

English _75

Z6806127401A_SRD-470, 470D-IB_EN75 75Z6806127401A_SRD-470, 470D-IB_EN75 75 2010-04-30 오후 6:10:312010-04-30 오후 6:10:31

web viewer

SAVING THE LIVE SCREEN ON THE PC

CAPTURE : Saves the current screen into a BMP or JPEG

•

fi le.

The default saving path is “C:\Program Files\Samsung\Dvr



M

•

Web Viewer\SnapShot\Live”. To change the saving path, click
<SAVE PATH ( )> button and then select the path you
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\
SnapShot\” by default, which cannot be modifi ed.

The fi le is automatically named as following : “IP address_Port number_YYYYMMDD



index”
Ex) 192.168.0.200_554_20100414_093118_01_00

PRINT : Prints out the selected screen out of the currently
displayed live screens. It also prints the IP address, time,
camera number and the current event status together.

_HHMMSS_camera number_

RECORD : Saves the current image on the screen and

•

saves it as a avi video fi le.

To record it, it is required at least 1GB of available space.



M



The default saving path is “C:\Program Files\Samsung\Dvr
Web Viewer\VideoClip\Live”. To change the saving path, click
<SAVE PATH (
want. For Windows Vista or 7, the saving path is “C:\users\
(user ID)\AppData\Local-Low\Samsung\DVR Web Viewer\VideoClip\”
and it cannot be modifi ed.

The fi le is automatically named as following : “IP address_Port number_YYYYMMDD



index”
Ex) 192.168.0.200_554_20100406_070455_01_00

For AVI Save, you need the Xvid codec for playing saved fi les.




HDD Minimum Free Size : During the recording, if there is no more capacity available in the HDD than set free space
will prompt with a popup message : “Cannot record due to insuffi cient disc space in the HDD”.

)> button and then select the path you

_HHMMSS_camera number_

76_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN76 76Z6806127401A_SRD-470, 470D-IB_EN76 76 2010-04-30 오후 6:10:342010-04-30 오후 6:10:34

CHANGING THE LIVE SCREEN CHANNEL

Blue numbers : Indicates that the current channel is

•

connected to a camera.

Gray numbers : Indicates that the current channel is not

•

connected to any camera.

If you select 4-split mode, the channel button for each of



cameras 1 ~ 4 will turn blue.

USING PTZ CAMERA

Click the direction buttons to control the camera.

 WEB VIEWER

•

<

You can zoom in or out an image by using the ZOOM button.

<

•

You can adjust the entering light amount by using the IRIS button.

•

<

You can adjust the focus by using the FOCUS button.

•

MENU : Appears the camera menu screen.

>

>

>

English _77

Z6806127401A_SRD-470, 470D-IB_EN77 77Z6806127401A_SRD-470, 470D-IB_EN77 77 2010-04-30 오후 6:10:372010-04-30 오후 6:10:37

web viewer

•

PRESET : Moves the lens direction to a preset direction.

1.

If you click a preset, the camera moves to the selected
preset's position.

2.

You can delete the selected preset or all presets.

3.

You can save a new preset number and name.

You can save presets up to 20.



M

AUTOPAN : Moves the camera lens direction between

•

2 points set for the camera.

SCAN : Moves the camera lens direction between 2 preset

•

points of the camera.

PATTERN : You can set camera various movement patterns

•

such as zoom, move, etc. so that a camera automatically
moves according to the pattern.

While the DVR controls a PTZ camera, Web Viewer cannot



M

control the camera.
Camera menu setup is only available for camera supporting



the function.
Each function of PTZ is same to that of the DVR.



Pan/Tilt of the Smart dome camera is manipulated



automatically to center the camera to the mouse clicked
point.

If you drag the mouse using the left button on a certain point,



Pan/Tilt of the Smart dome camera is manipulated
automatically to center the camera to the middle point between the dragging start and end position.
Upward dragging will zoom out, while downward dragging will zoom in.

Tilt of Power PTZ operates properly within 45°.



Power and Pan Tilt functions are only available for camera supporting the functions.



Ex : Samsung SCC-C6475

78_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN78 78Z6806127401A_SRD-470, 470D-IB_EN78 78 2010-04-30 오후 6:10:402010-04-30 오후 6:10:40

USING SEARCH VIEWER

 WEB VIEWER

The Search Viewer screen consists of following :

This displays the IP address and the model name of the connected DVR.

There are 4 tabs available: <LIVE>, <SEARCH>, <SETUP>, <ABOUT>.

Switch to a split mode.

Shows the IP address and model name of the connected DVR.

These buttons are used for capture, print, and save the image.

This displays a calendar at which you can search the recorded video.

This displays a timeline at which you can search the recorded video by the time.

These buttons are used for controlling playback.

This displays the screen for playback of recorded video.

<SEQUENCE>, <PREVIOUS>, <NEXT> buttons are not available in SEARCH menu.



M

English _79

Z6806127401A_SRD-470, 470D-IB_EN79 79Z6806127401A_SRD-470, 470D-IB_EN79 79 2010-04-30 오후 6:10:422010-04-30 오후 6:10:42

web viewer

SPLIT-SCREEN

You can change the split mode by clicking each number icon.

SINGLE MODE QUAD MODE

•

Click <
The screen displays the selected camera connected to the DVR in
“SINGLE MODE”.

Click <

•

The screen displays the selected camera connected to the DVR in
“QUAD MODE”.

> button.

> button.

CONNECTED DVR

This displays the IP address and the status of the connecting DVR.

Connection failure message



M

No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of users is exceeded.

The number of simultaneous connection is limited to 3.



80_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN80 80Z6806127401A_SRD-470, 470D-IB_EN80 80 2010-04-30 오후 6:10:462010-04-30 오후 6:10:46

SAVING THE LIVE SCREEN ON THE PC

CAPTURE : Saves the current screen into a BMP or JPEG

•

fi le.

The default saving path is “C:\Program Files\Samsung\Dvr



M

•

Web Viewer\SnapShot\Search”. To change the saving path,
click <SAVE PATH ( )> button and then select the path
you want. For Windows Vista or 7, the saving path is “C:\
users\(user ID)\AppData\LocalLow\Samsung\DVR Web
Viewer\SnapShot\”and it cannot be modifi ed.

The fi le is automatically named as following : “IP address_Port number_YYYYMMDD



index”
Ex) 192.168.0.200_554_20100414_093118_01_00

PRINT : Prints the playback screen that is now being
displayed. It also prints IP address, time, camera number,
and current event state.

 WEB VIEWER

_HHMMSS_camera number_

RECORD : If you select a channel and click this button

•

during playback (only play), the video data is saved in a DVR
fi le. (It is saved in the designated folder on your PC.)
To stop recording, click this button again.

To record it, it is required at least 1GB of available space.



M

The default saving path is “C:\Program Files\Samsung\Dvr



Web Viewer\VideoClip\Search”. To change the saving path,
click <SAVE PATH (
“C:\users\(user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\VideoClip\” and it cannot be modifi ed.

The fi le is automatically named as following : “IP address_Port number_YYYYMMDD



index”
Ex) 192.168.0.200_554_20100406_070455_01_00

For AVI save, you need the Xvid codec for playing saved fi les.



)> button and then select the path you want. For Windows Vista or 7, the saving path is

_HHMMSS_camera number_

English _81

Z6806127401A_SRD-470, 470D-IB_EN81 81Z6806127401A_SRD-470, 470D-IB_EN81 81 2010-04-30 오후 6:10:502010-04-30 오후 6:10:50

web viewer

SEARCHING THE RECORDED VIDEO IN THE CALENDAR

If the video data has been recorded on a date, the date is
distinguished in green. If you click the date, the recorded video
information is displayed in the time line. When you click
<Today>, it is changed to today’s date.

SEARCHING THE RECORDED VIDEO IN THE TIMELINE

It displays the recorded video data status on the DVR after a date is
selected. The normal mode displays the time ranging from 0 to 24 Hours
while the extension mode displays the time every 2 hours.

[Normal Mode]

If you click <

•

•

Each time line represents 1 hour.

> button, it changes to the extension mode.

[Extension Mode]

•

If you click <

•

Each time line represents 5 minutes.



M

> button, it changes to the normal mode.

The channels are ranging from CH01 to CH04.

82_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN82 82Z6806127401A_SRD-470, 470D-IB_EN82 82 2010-04-30 오후 6:10:532010-04-30 오후 6:10:53

CONTROLLING PLAYBACK

Fast Backward : Reverse-plays faster(2x).

Reverse Play : Performs Reverse Play.

Play : Performs playback.

Fast Forward : Plays faster(2x).

Go to First :

Step Backward : Performs one step reverseplay by one frame.

Stop : Stops playing.

Step Forward : Performs one step forward by one frame.

Go to Last : Moves the last time of recorded video in the time line.

Moves the beginning time of recorded video in the time line.

 WEB VIEWER

VIEWER SETUP

You can confi gure the DVR settings remotely on the network.

To confi gure the DVR settings, click <Setup>.

System

You can confi gure the various settings of the DVR system.

Date/Time/Language

For more information, refer to <Date/Time/Language> in the <System Setup> menu. (Page 32)

1.

Select <Date/Time/Language> in the System menu.

2.

Confi gure the DVR settings according to your system
environment.

•

Date/Time

Set the date and time.

English _83

Z6806127401A_SRD-470, 470D-IB_EN83 83Z6806127401A_SRD-470, 470D-IB_EN83 83 2010-04-30 오후 6:10:562010-04-30 오후 6:10:56

web viewer

•

Time Synchronization Setup

Set the time synchronization.

•

Display

Date Format : Set the date type.

Time : Select a time format to display on the screen.

•

DST (Daylight Saving Time)

DST is displayed an hour ahead of the standard time of the
time zone.

•

Language

Select a preferred language for the DVR.

Holiday

You can set specifi c dates to Holidays according to your
preferences.
For more information, refer to <Setting Holiday> in the
<System Setup> menu. (Page 33)

Permission Management

For more information, refer to <Permission Management> in the <System Setup> menu. (Page 34)

•

Admin

You can change the admin ID or the password.

84_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN84 84Z6806127401A_SRD-470, 470D-IB_EN84 84 2010-04-30 오후 6:11:002010-04-30 오후 6:11:00

Group

•

Users are classifi ed into groups and the permission can be
set according to the group.

First of all, add a group.



User

•

You can add, change or remove a user or users.

Setup

•

You can set the user permission.

 WEB VIEWER

System Management

For more information, refer to <System Management> in the <System Setup> menu. (Page 38)

System Information

•

You can see information of the current system.
Check the software version, broadcast format and
MAC address.

English _85

Z6806127401A_SRD-470, 470D-IB_EN85 85Z6806127401A_SRD-470, 470D-IB_EN85 85 2010-04-30 오후 6:11:042010-04-30 오후 6:11:04

web viewer

Device

You can check a list of devices that are connected to the DVR and confi gure the necessary settings.
Click <Device> in the menu screen.
For more information, refer to “Setting the Device”. (Page

Camera

Camera

•

You can confi gure the settings of the camera that is
connected to the DVR.

PTZ

•

You can confi gure the settings of the PTZ camera that is
connected to the DVR.
Set the ID and protocol.

42)

Storage Device

You can check and change the settings of the storage device.

Device

•

You will see a list of storage devices that are connected to the
DVR.
You can check the type, used/total, usage and status of the
device.

86_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN86 86Z6806127401A_SRD-470, 470D-IB_EN86 86 2010-04-30 오후 6:11:092010-04-30 오후 6:11:09

HDD Alarm

•

You can set the alarm output channel and the alarm duration
for an error.

Remote Device

You can see a list of remote devices including PTZ cameras
and system keyboards that are connected to the RS-485 port
of the DVR and confi gure the necessary settings.

 WEB VIEWER

POS Device

You can set the channel, preset and communication port of
the POS device that is connected to the DVR.

You cannot set to use the POS device remotely.



M

Monitor

Monitor

•

You can confi gure the monitoring screen settings and set the
output system.

English _87

Z6806127401A_SRD-470, 470D-IB_EN87 87Z6806127401A_SRD-470, 470D-IB_EN87 87 2010-04-30 오후 6:11:122010-04-30 오후 6:11:12

web viewer

Spot Out

•

With the monitor connected via the SPOT port, if there occurs
an event such as Sensor, Motion, or Alarm, you can select a
video output mode for external monitoring.

Mode

•

You can switch between live mode and play mode.

Record

For more information, refer to <Setting the Recording>. (Page 50)

Recording Schedule

If you set a recording schedule for a specifi c date and time,
the recording will start at that specifi c time.

- Apply to All CH : Click <Apply to All CH> to display the

confi rmation window.

88_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN88 88Z6806127401A_SRD-470, 470D-IB_EN88 88 2010-04-30 오후 6:11:172010-04-30 오후 6:11:17

Event Record Duration

You can set the start and end times of recording that will be
activated if an event occurs.

REC Quality & Resolution

Standard/Event

•

You can set the resolution, frame rate and recording quality for
each channel.

 WEB VIEWER

Record Option

You can set the Disk End Mode.

Event

For more information, refer to <Setting the Event>. (Page 53)

Sensor Detection

You can set the sensor operation mode and the synchronized
camera as well as the alarm output type and the duration.

English _89

Z6806127401A_SRD-470, 470D-IB_EN89 89Z6806127401A_SRD-470, 470D-IB_EN89 89 2010-04-30 오후 6:11:222010-04-30 오후 6:11:22

web viewer

Motion Detection

You can set the motion detection mode and the sensitivity
as well as the alarm output type and the duration.

•

Motion Region

Set the target motion detection area

Video Loss Detection

You can set the alarm output time if a video loss occurs.

Alarm Schedule

You can schedule the alarm output according to the day of
the week and the time.
The default setting is Event Sync, which activates the alarm
only if an event occurs.

90_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN90 90Z6806127401A_SRD-470, 470D-IB_EN90 90 2010-04-30 오후 6:11:262010-04-30 오후 6:11:26

Network

For more information, refer to <Network Confi guration>. (Page 57)

Connection

A remote user can access the DVR via the network to check
the current mode and the IP address.

•

Connection

You can set the network connection route.

•

Protocol

You can confi gure the protocol related settings.

 WEB VIEWER

DDNS

You can check the DDNS settings.

Live Transfer

A remote user can set the images of the DVR.

Live Transfer

•

A remote user can set the image resolution of the transferred
data.

English _91

Z6806127401A_SRD-470, 470D-IB_EN91 91Z6806127401A_SRD-470, 470D-IB_EN91 91 2010-04-30 오후 6:11:312010-04-30 오후 6:11:31

web viewer

Mailing Service

You can specify the SMTP server that sends a mail if an event
occurs and set the recipient group and users.

•

SMTP

You can set the server that sends mails and specify if you use
the authentication process.

•

Event

You can set the event interval and specify which events the
server sends mails for.

•

Group

You can add a group to receive the mail if an event occurs
and set the permission to receive the event mail for each
group.

•

Recipient

You can add a user or users who will receive the mail.

92_ web viewer

Z6806127401A_SRD-470, 470D-IB_EN92 92Z6806127401A_SRD-470, 470D-IB_EN92 92 2010-04-30 오후 6:11:362010-04-30 오후 6:11:36

ABOUT

Click <ABOUT>.

Displays the model name of connected DVR and the version
of Web Viewer.

 WEB VIEWER

English _93

Z6806127401A_SRD-470, 470D-IB_EN93 93Z6806127401A_SRD-470, 470D-IB_EN93 93 2010-04-30 오후 6:11:402010-04-30 오후 6:11:40

backup viewer

SEC BACKUP VIEWER

You can play a fi le that is backed up in the format of SEC.

Backup in the format of SEC will involve in generating two fi les: one for the backup data and one for the viewer.

If you run the backup fi le viewer, the backup data fi le will be automatically played.

Recommended System Requirements

PCs with a lower specifi cation than the recommended below may not fully support forward/backward and
high-speed playback.

•

OS : Windows XP professional, Windows Vista, Windows 7

•

CPU : Intel Core2-Duo 2.4GHz or higher

•

RAM : DDR PC-3200 1G or more

•

VGA : Geforce 6200 or higher

94_ backup viewer

Z6806127401A_SRD-470, 470D-IB_EN94 94Z6806127401A_SRD-470, 470D-IB_EN94 94 2010-04-30 오후 6:11:422010-04-30 오후 6:11:42

Name Description

Audio

Screen Printout

File Tamper

Detection

Zoom In/Out

Display of storage time range

/

A toggle button. Each time you press this button, the audio output will toggle
between activated and deactivated.

You can adjust the volume level from 0 to 100.

Saves the current screen as an image fi le. Supported fi le formats include
BMP and JPEG.

 BACKUP VIEWER

Prints out the current screen. You should have installed the appropriate printer
driver before you can print out the screen.

A toggle button. Each time you press this button, it will toggle between
activated and deactivated. The closed lock icon indicates activation of the fi le

/

tamper detection, which will blink the screen three times and stop playing if
an unauthorized manipulation of a data fi le is detected.

A message of "The fi le is forged” will display in the menu bar.



Collapses the time range that is displayed on the range bar of the storage
time. You can collapse the range bar until the overall range is shortened to 24
hours.

Enlarges the time range that is displayed on the range bar of the storage
time. You can enlarge the range bar until the overall range is extended to 1
minute.

Displays the time range of a stored video fi le.
You can move the gridline of the range bar to select a time point to play.

Speed

Play

A toggle button; each time you press this button, the "Slow Playback " icon
changes its color to display it’s activated/deactivated. If it is activated, you can
use the play speed control to adjust the play speed up to x1/32 forward and
backward respectively, whereas if deactivated, you can adjust up to x32
forward and backward.

A toggle button; each time you press this button, the "Lock Speed" icon
changes its color to display it’s activated/deactivated.
If activated, the adjusted speed will be kept even if you release the mouse on
the speed bar. If deactivated, the adjusted speed will be applied only while
you use the mouse to hold the adjusted speed, and if you release the mouse,
the speed will restore to x1.

You can adjust the play speed up to x32 forward and backward respectively,
which varies according to the frame rate per second of the source.
If the frame rate per second is between 20 and 30, the maximum speed is
limited to x4, if the FPS is between 11 and 19, it is limited to x16, and if the
FPS is 6 or less, it supports up to x32.

Displays the next frame. This is available only if the playback is stopped.

A toggle button. Press it once to start playing the video and switch the button
mode to 'Pause', and press it again to switch the button mode to Play and
stop playing temporarily.

Displays the previous frame. This is available only if the playback is stopped.

English _95

Z6806127401A_SRD-470, 470D-IB_EN95 95Z6806127401A_SRD-470, 470D-IB_EN95 95 2010-04-30 오후 6:11:462010-04-30 오후 6:11:46

appendix

PRODUCT SPECIFICATION

Item Details Note

Operating System Embedded OS

Broadcast Format NTSC/PAL System

Input Voltage AC 100~240V

Power Consumption

Video

Audio

Live Screen

Video In

Video Out

Audio In

Audio Out

Resolution & Frame
Rate

Display Mode

59W

Composite 4 Channel

- 1.0Vp-p

- 75Ω Hi Z Termination
BNC Type
Loop Through Out 4 Channel

- Auto Termination

Composite 2 Channel

- Normal Video Output 1 Channel

- Spot Output 1

- BNC Type
VGA 1 Channel

Mono 4 Channel
4 Channel : RCA Type

- 5dBm, 600Ω

Mono 1 Channel

- 6dBm
RCA Type

NTSC PAL

Resolution 704x480 704x576

Frame Rate

Single
Split Modes: 4-splits
PIP
Mode sequence
Freeze
2 X Zoom

120ips 100ips

96_ appendix

Z6806127401A_SRD-470, 470D-IB_EN96 96Z6806127401A_SRD-470, 470D-IB_EN96 96 2010-04-30 오후 6:11:462010-04-30 오후 6:11:46

Item Details Note

Compression
Method

Resolution & Quality

Record

Record Mode

Frame Rate

Storage Internal

Search Mode

Play

Resolution &
Specifi cation

Video : H.264
Audio : G.723

Resolution Spec. (Quality) Max Recording Rate

CIF(S)
352X240(NTSC)
/352X288(PAL)

2CIF(M)
704x240(NTSC)
/704x288(PAL)

4CIF(L)
704x480(NTSC)
/704x576(PAL)

Level8 (high)
~ Level1 (low)

Level8 (high)
~ Level1 (low)

Level8 (high)
~ Level1 (low)

CIF(S)
120ips(NTSC)/
100ips(PAL)

2CIF(M)
120ips(NTSC)/
100ips(PAL)

4CIF(L)
120ips(NTSC)/
100ips(PAL)

Normal Recording  REC button
Scheduled Recording  Schedule Table
Event Recording

- Alarm Detection

- Motion Detection

- Video Loss

- Pre & Post Recording

NTSC : 0.9, 1.9, 3.8, 7.5, 15, 30ips
PAL : 0.8, 1.6, 3.1, 6.2, 12.5, 25ips

SRD-470D : SATA HDDx1(MAX)
MAX HDD size : 500GB x 1= 500GB

SRD-470 : SATA HDDx2(MAX)
MAX HDD size : 500GB x 2 = 1TB

Calendar Search
Event Search

- Alarm, Motion, Video Loss
Time/Date Search
Go to First
Go to Last
Backup Search
Text Search(for POS)
Motion Search
Preview

Resolution Specifi cation

CIF(S)
352X240(NTSC)
/352X288(PAL)

2CIF(M)
704x240(NTSC)
/704x288(PAL)

4CIF(L)
704x480(NTSC)
/704x576(PAL)

CIF(S)
120ips(NTSC)/
100ips(PAL)

2CIF(M)
120ips(NTSC)/
100ips(PAL)

4CIF(L)
120ips(NTSC)/
100ips(PAL)

If you want to
add an internal
HDD, please
refer to
“Adding a
HDD”.
(Page

14)



APPENDIX

English _97

Z6806127401A_SRD-470, 470D-IB_EN97 97Z6806127401A_SRD-470, 470D-IB_EN97 97 2010-04-30 오후 6:11:472010-04-30 오후 6:11:47

appendix

Item Details Note

Display Mode

Play

Play Mode

Backup

Network Ethernet : 10/100/1000 BaseT, ADSL(PPPoE), DHCP

Serial Communication

Alarm

PC Requirements

Remote Viewer

Operating
Systems

Features

Single /4-splits

Play, Pause, Stop, 2xDigital Zoom
Fast Forward/Fast Reverse

- 2x, 4x, 8x,16x, 32x, 64x

USB External HDD
USB CD/DVD Writer, Internal DVD(SRD-470D only)
USB Memory
USB HDD-MAX 1(USB hub not supported)

RS-485  PTZ Device Control
Remote Control Device
RS-232C  POS

Input : 4 channels

CPU : Intel Core 2 Quad 2.5GHz or higher
RAM : 2G
VGA : 32M RAM(64M or more)
DirectX 8.1

Windows XP(Pro),
Windows-2000(Pro)
Windows Vista(Home Basic/Premium)
Windows 7

Live Image Monitoring Mode
Local File Search & Play Back Mode
Remote File Search & Play Back Mode

Temperature (Operation) 0°C ~ 40°C (32°F ~ 104°F)

Temperature (Storage) -20°C ~ 60°C (-4°F ~ 140°F)

Humidity (Operation) 20% to 85% RH

Humidity (Storage) 20% to 85% RH

Dimension (W x H x D) 215 x 353 x 88mm (8.46 x 13.88 x 3.64 inch)

Weight

It needs extra H/W to support ATM/POS function. So please contact your vendor to obtain H/W.

SRD-470 : ~4Kg(8.82lb)
SRD-470D : ~4.85Kg(10.69lb)

98_ appendix

H (leg not included)

Z6806127401A_SRD-470, 470D-IB_EN98 98Z6806127401A_SRD-470, 470D-IB_EN98 98 2010-04-30 오후 6:11:472010-04-30 오후 6:11:47

PRODUCT OVERVIEW

SRD-470/470D

•



APPENDIX

12

353

SRD-470D SRD-470

215

10.5 88

215

10.5 88

English _99

Z6806127401A_SRD-470, 470D-IB_EN99 99Z6806127401A_SRD-470, 470D-IB_EN99 99 2010-04-30 오후 6:11:482010-04-30 오후 6:11:48

appendix

DEFAULT SETTING

This returns the factory default settings.

The settings are made as follows;

Use System/Load Factory Default in MENU

•

The default settings are based on SRD-470D.



Category

System Settings

Device

Details Factory Default

Date YYYY-MM-DD

Time Format 24 hours

Date/Time/Language Date/Time/Language

Admin

Permission

Management

Setting

System Management System Information Broadcast Format NTSC/PAL

Camera

Camera

PTZ

Screen Setup

Storage Device HDD Alarm

Baudrate 9600

Parity None

Data 8

Remote Device

Stop bit 1

Transfer Type Half Duplex

System Keyboard OFF

Remote Control ON(00)

Time Zone GMT

Time Synchronize OFF

DST OFF

Language English

ID admin

New Password 4321

Restricted Access All

Auto Logout 3 Min

Video ON

Audio OFF

CH Name

SEQ-Dwell Time 5sec

Progressive OFF

ID Camera No.

Protocol None

Brightness 50

Contrast 50

Color 50

Check Alarm Output Port OFF

Duration OFF

Replace Alarm Output Port OFF

Duration OFF

CAM 01 ~ CAM 04

100_ appendix

Z6806127401A_SRD-470, 470D-IB_EN100 100Z6806127401A_SRD-470, 470D-IB_EN100 100 2010-04-30 오후 6:11:492010-04-30 오후 6:11:49