Samsung 460UT-B, 460UTn-2, 460UT-2, 460UTn-B, 460UTn2-UD2 User Manual

SyncMaster 460UTn-2, 460UTn2-UD2, 460UT-2, 460UTn-B, 460UT-B

LCD Display

User Manual

The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property dam­age.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily
harm or damage to the equipment.

Note

Power

Prohibited

Do not disassemble

Do not touch

When not used for extended period of time, set your computer to DPM.
If using a screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases

(or countries).
Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or

loose power outlet.

Important to read and under­stand at all times

Disconnect the plug from the
outlet

Ground to prevent an electric
shock

• Otherwise, this may result in electric shock or fire.

Do not touch the power plug with wet hands when removing or

plugging the plug into the outlet.

• Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power out-

let.

• Otherwise, it may result in electric shock or personal injury.

Safety Instructions

Ensure that the power plug is plugged into the power outlet

firmly and correctly.

• Otherwise, this may result in fire.

Do not forcefully bend or pull the power plug and do not place

any heavy material on it.

• Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

• Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

• Otherwise, this may result in damage to the product due to
electric shock.

To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.

Installation

• Otherwise, this may cause electric shock or fire.

Use only the power cord provided by our company. Do not use
the provided power cord of another product.

• Otherwise, this may result in fire or electric shock.

Connect the power plug to a wall outlet that can be easily
reached.

• When a problem occurs with the product, you must unplug the

power plug to cut the power off completely. You cannot cut the
power off completely using only the power button on the prod­uct.

Be sure to contact an authorized Service Center when installing your
monitor in a location with heavy dust, high or low temperatures, high hu­midity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

• Otherwise, it may be dropped and cause personal injury, and/

or damage the product.

When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

Safety Instructions

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIG­ARETTES AND ANY HEATING APPLIANCES NEAR THE
PRODUCT.

• Otherwise, this may result in fire.

Keep heating appliances as far away from the power cord or the
product as possible.

• Otherwise, this may result in electric shock or fire.

Do not install it in a badly ventilated location such as a bookcase
or closet.

• Otherwise, this may result in fire due to an increase in the in-

ternal temperature.

When putting the product down, make sure to put it down softly.

• Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

• Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall
mount.

Otherwise, it may fall and cause personal injury.

•

• Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that
there is a clearance of more than 4 inches (10 cm) from the wall.

• Otherwise, it may result in fire due to an increase in the internal

temperature.

Ensure that the packaging vinyl is kept away from children.

• Otherwise, it may result in serious harm (suffocation) if children

play with it.

If the height of your monitor is adjustable, do not place any ob­ject or part of your body on the stand when lowering it.

• This may cause damage to the product or the person carrying

it.

Edible oil, such as soybean oil, can damage or deform the prod-

uct. Do not install the product in a kitchen or near a kitchen counter.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen,
wipe with a slightly moistened, soft cloth.

Do not spray cleaner directly onto the surface of the product.

• Otherwise, this may result in the discoloration and distortion of

the structure and the screen surface may peel off.

Safety Instructions

When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.

• Otherwise, it may result in fire.

When cleaning the product, make sure to disconnect the power
cord.

• Otherwise, it may result in electric shock or fire.

When cleaning the product, disconnect the power cord and
clean it with a soft, dry cloth.

• (Do not use chemicals such as wax, benzene, alcohol, thinner,

mosquito repellant, lubricant, or cleaner.) These may change
the appearance of the product surface and peel off the indica­tion labels on the product.

Since the product housing is easily scratched, make sure to use
the specified cloth only.

Others

When cleaning the product, do not spray water directly onto the
main body of the product.

• Ensure that water does not enter the product and that it is not

wet.

• Otherwise, this may result in electric shock, fire or a malfunc-

tion.

The product is a high voltage product. Do not disassemble, re­pair or modify the product yourself.

• Otherwise, this may result in electric shock or fire. If the product

needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and con­tact a Service Center.

• Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.

• Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.

• Otherwise, this may result in electric shock or fire.

Safety Instructions

If thunder or lightning is occurring, do not touch the power cord
or antenna cable.

• Otherwise, this may result in electric shock or fire.

Do not try to move the monitor by pulling only the wire or the
signal cable.

• Otherwise, it may fall and result in electric shock, damage to

the product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.

• Otherwise, it may fall and result in electric shock, damage to

the product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table
or curtain.

• Otherwise, it may result in fire due to an increase in the internal

temperature.

Do not place any containers containing water, vases, flower­pots, medicines as well as any metal on the product.

• If water or a foreign material enters the product, disconnect the

power cord and contact a Service Center.

• This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material
near the product.

• Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable objects, such as matches or paper, inside the
product (through the ventilating openings, input and output termi­nals, etc).

• If water or foreign material enters the product, disconnect the

power cord and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain
may occur.

• If you are not using your product for a long period of time, put

it into sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

• Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume
too high.

• Having the sound too loud may damage your hearing.

Safety Instructions

To avoid eyestrain, do not sit too close to the product.

Take a rest for at least five (5) minutes after using the monitor
for one (1) hour.

This reduces eye fatigue.

Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.

• Otherwise, it may fall and cause personal injury and/or damage

the product.

• If you use the product in a location exposed to vibrations, it may

damage the product and result in fire.

When moving the product, turn the power off and disconnect
the power plug, antenna cable, and all the cables connected to the
product.

• Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up
onto the product.

• The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.

• Otherwise, this may result in overheating or fire due to dust,

and may result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the attention of children and to the
product.

• Your children may hang onto the product causing it to fall and

this may result in personal injury or death.

Be careful that children do not place the battery in their mouths
when removed from the remote control. Place the battery in a lo­cation that children or infants cannot reach.

• If children have had the battery in their mouths, consult your

doctor immediately.

When replacing the battery, insert it with the right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause

fire, personal injury or damage due to leakage of the internal
liquid.

Use only the specified standardized batteries, and do not use a
new battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, per-

sonal injury or damage due to a leakage of the internal liquid.

Safety Instructions

The batteries (and rechargeable batteries) are not ordinary re­fuse and must be returned for recycling purposes. The customer
is responsible for returning the used or rechargeable batteries for
recycling.

• The customer can return used or rechargeable batteries to a

nearby public recycling center or to a store selling the same
type of the battery or rechargeable battery.

Do not place the product in a location exposed to direct sunlight
or near any heat such as a fire or heater.

• This may reduce the lifetime of the product, and may result in

fire.

Do not drop any objects onto the product or cause any impact
to the product.

• Otherwise, this may result in electric shock or fire.

Do not use a humidifier near the product.

• Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power
plug; ventilate immediately.

• If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display
panel becomes hot. Do not touch it.

Keep the small accessories in a location out of the reach of
children.

Be careful when adjusting the angle of the product or the height
of the stand.

• This may result in personal injury as your hand or fingers may

become caught.

• Also, if you tilt the product too far, it may fall and cause personal

injury.

Do not install the product in a location low enough for children
to reach.

• Otherwise, it may fall and result in personal injury.

• Since the front part of the product is heavy, install the product

on a level and stable surface.

Safety Instructions

Do not put any heavy objects on the product.

• This may result in personal injury and/or damage to the prod-

uct.

Introduction

Package Contents

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.

Lift up the package box by

both sides of the package

• After unpacking the package, make sure to check the contents of the package.

• Store the packaging box in case you need to move the Product later.

• If any items are missing, contact your dealer.

• Contact a local dealer to purchase optional items.

Unpacking

holding the grooves on

box.

Note

Check the contents of the

package.

Remove the Styrofoam

and vinyl cover.

LCD Display

Manuals

Introduction

Quick Setup Guide Warranty Card

(Not available in all loca-

tions)

MagicInfo Software DVD

(Applicable to the

460UTn-2, 460UTn2-UD2,

460UTn-B model only)

Cables

Power Cord D-Sub Cable

Others

User Manual

Remote Control
(BP59-00138B)

Sold separately

Semi Stand KIT LAN Cable USB Cable

Batteries (AAA X 2)

(Not available in all loca-

tions)

(Applicable to the

460UTn-2, 460UTn2-UD2,

460UTn-B model only)

Introduction

Sold separately

RGB to BNC Cable RGB to Component Cable Network Box

(Applicable to the

460UT-2, 460UT-B model

Wall Mount KIT TV Tuner Box (US Only)

Note

only)

Accessories that can be purchased with the product vary by country.

Your LCD Display
Front

SOURCE button
Switches from PC mode to Video mode. Selects the input source that an

external device is connected to.
[PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [Dis-

playPort] → [MagicInfo] → [TV]

Note

• A TV tuner box (sold separately) must be connected to use the TV. (US
Only)

• A network box (sold separately) must be connected to use MagicInfo
with a 460UT-2, 460UT-B model.

POWER button

Use this button for turning the LCD Display on and off.

Rear

Introduction

Power indicator
Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.

Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.

Note

See the "Connections" section for details about cable connections. The LCD Display's con­figuration at the back may vary slightly depending on the model.

POWER S/W ON [ │ ] / OFF

Switches the LCD Display On/Off.

POWER

The power cord plugs into the LCD Display
and the wall outlet.

IR OUT/IN

Receives a signal from the remote control
and outputs the signal through Loopout when
a removable sensor board is connected.

AMBIENT SENSOR IN

Supplies power to the removable sensor
board and receives a signal from the light
sensor.

Introduction

DVI OUT (LOOPOUT)

• Connect a monitor to another monitor
through a DVI, DVI to HDMI cable.

• Connect a DVI or DVI-HDMI cable to [DVI

OUT (LOOPOUT)] on the product and
[DVI IN] or [HDMI IN] on another monitor.

• HDMI and network signals sent via the
[DVI OUT(LOOPOUT)] port are dis­played on the second display which has
the [DVI IN] port.

Note

• The Loopout function can be used to du­plicate the screen of the primary display.
Connect [DVI OUT] on the primary dis­play to [DVI IN] or [HDMI] on another
display.

• A maximum of 100 monitors can be con­nected to DVI-Loopout (using a 2m-long
DVI cable). Up to HD resolution can be
supported. Compatible input sources in­clude DVI IN, HDMI IN 1, and HDMI IN 2
(MagicInfo).

• The status of the cable may have a great
effect on the Loopout performance.

RGB/COMPONENT IN (PC/COMPO-

NENT Connection Terminal (Input))

• Connect the [RGB/COMPONENT IN]
port on the monitor to the RGB port on the
PC using the D-SUB cable.

• Connect the [RGB/COMPONENT IN]
port on the monitor to the COMPONENT
port on the external device using the RGB
to COMPONENT cable.

• Connect the [RGB/COMPONENT IN]
port on the monitor to the BNC port on the
PC using the RGB to BNC cable.

DVI IN (PC Video Connection Terminal)

Connect the [DVI IN] port on the monitor to
the DVI port on the PC using the DVI cable.

RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/
DP/HDMI Audio Connection Terminal (In­put))

Introduction

Connect the [RGB/DVI/DP/HDMI AUDIO
IN] terminal of the monitor and the speaker
output terminal of your computer's sound
card using a stereo cable (sold separately).

DP IN
Receives a signal from the Display port.
Connect a DP cable to [DP IN] on the product

and DP IN on another display.

AV/COMPONENT AUDIO IN [R-AUDIO-

L]
Connect the [AV/COMPONENT AUDIO IN

[R-AUDIO-L]] port on the monitor to the audio

output port on the PC or on the external de­vice using an audio cable.

AV IN
Connect the [AV IN] terminal of your monitor

to the video output terminal of the external
device using a VIDEO cable.

AUDIO OUT
Connect a headphone or an External speak-

er.

DC OUT

Make sure to use connecting [DC OUT] ter-
minal to the authorized TV-Tuner Box. (US
Only)

Otherwise, this may result in damage

to the product.

HDMI IN 1

• Connect the [HDMI IN 1] terminal at the

back of your LCD Display to the HDMI
terminal of your digital output device us­ing a HDMI cable.

• Up to HDMI 1.3 can be supported.

Note

• A normal external device (DVD player or

camcorder, etc.) or a TV tuner box can be
connected to the [HDMI IN 1] terminal.

Introduction

• To use a TV tuner box (US Only), make

sure to connect it to the [HDMI IN 1] ter-
minal.

HDMI IN 2 (MAGICINFO)

• Connect the [HDMI IN 2 (MAGICINFO)]

terminal at the back of your LCD Display
to the HDMI terminal of your digital output
device using a HDMI cable.

• Up to HDMI 1.3 can be supported.

Note

The MAGICINFO OUT port must be connec­ted to the [HDMI IN 2 (MAGICINFO)] port.

RJ 45 MDC (MDC PORT)

MDC(Multiple Display Control) Program Port
Connect the LAN cable to [RJ45 MDC] on the

product and LAN on the PC. To use an MDC,
the MDC program must be installed on the
PC.

Note

Go to Multi Control and select RJ45 MDC
as the MDC Connection.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port
Connect a serial cable (cross type) to

[RS232C] on the product and RS232C on the
PC. To use an MDC, the MDC program must
be installed on the PC.

Note

Go to Multi Control and select RS232C
MDC as the MDC Connection.

Introduction

RGB OUT

MagicInfo video output port

Note

Applicable to the 460UTn-2, 460UTn2-UD2,
460UTn-B model only.

MAGICINFO OUT
Outputs MagicInfo DP signals. It should be

connected to [HDMI IN 2 (MAGICINFO)] via
a DP to HDMI cable.

LAN (LAN Connection Terminal)
Connects to a LAN cable to allow Internet or

network access in MagicInfo mode.

Note

Applicable to the 460UTn-2, 460UTn2-UD2,
460UTn-B model only.

USB (USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device

Compatible.

Note

Applicable to the 460UTn-2, 460UTn2-UD2,
460UTn-B model only.

Kensington Lock slot

A Kensington Lock is an anti-theft device that
enables users to lock the product so that they
can safely use it in public locations. Since the
shape and usage of the locking device may
differ depending on the model and the man­ufacturer, for more information, refer to the
User Manual supplied with the locking device
for more information.

To lock the product, follow these
steps:

1. Wrap the Kensington lock cable around

a large, stationary object such as a desk
or chair.

2. Slide the end of the cable with the lock

attached through the looped end of the
Kensington lock cable.

Note

Introduction

3. Insert the Kensington Lock into the se-

curity slot ( ) on the back of the dis­play.

4.

Lock the lock ( ).

Note

• You must purchase the Kensington Lock

separately.

• These are general instructions. For exact

instructions, see the User Manual sup­plied with the locking device.

• You can purchase the locking device

from an electronics store, an online shop,
or our service center.

See the "Connections" section for details about cable connections.

Remote Control

Note

• The performance of the remote control may be affected by a TV or other electronic device
operating near the LCD Display , causing a malfunction due to interference with the fre­quency.

• A TV tuner box (sold separately) must be connected to use the TV. (US Only)

POWER
OFF

Number Buttons

/ GUIDE button

+ VOL -

SOURCE

D.MENU

TOOLS

Up-Down Left-Right buttons

INFO

The Color button and the PC/DVI/HDMI/DP
selection button

TTX/MIX

MTS/DUAL

ENTER/PRE-CH

Introduction

MUTE

CH/P
TV
MENU

RETURN

EXIT

MagicInfo

POWER

OFF

Number Buttons

/ GUIDE button

+ VOL -

SOURCE

Turns the product On.

Turns the product Off.

Used to enter the password during the OSD adjustment or
to use MagicInfo.

Press to change the channel.
The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.

- This function does not work for this LCD Display.
Adjusts the audio volume.

Selects a connected external input source or MagicInfo
mode.

Press the button to change the input signal SOURCE.
Changing the SOURCE is only allowed for external devices

that are connected to the LCD Display at the time.

D.MENU

TOOLS

Up-Down Left-Right but-

tons

INFO

The Color button and the
PC/DVI/HDMI/DP selection
button

DTV menu display

- This function does not work for this LCD Display.
Use to quickly select frequently used functions.

- This function does not work for this LCD Display.
Moves from one menu item to another horizontally, vertically

or adjusts selected menu values.

Current picture information is displayed on the upper left
corner of the screen.

In TV mode, these buttons can be used for setting the
broadcasting announcement function of a digital channel.

You can select the PC, DVI, HDMI or DP(DisplayPort) ex­ternal input directly in a mode other than TV mode.

Introduction

TTX/MIX

MTS/DUAL

TV channels provide written information services via tele­text.

- Teletext Buttons

- This is activated when a TV tuner box is installed.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

Audio Type MTS/S_Mode Default

FM Stereo Mono Mono Manual

Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.

Change

ENTER/PRE-CH

MUTE

CH/P

TV

MENU

RETURN

- This is activated when a TV tuner box is installed.
This button is used to return to the immediately previous

channel.

- This is activated when a TV tuner box is installed.
Pauses (mutes) the audio output temporarily. This is dis-

played on the lower left corner of the screen. The audio
comes back on if MUTE or - VOL + is pressed in the Mute
mode.

In TV mode, selects TV channels.

- This is activated when a TV tuner box is installed.
Selects the TV mode directly.

- This is activated when a TV tuner box is installed.
Opens the on-screen menu and exits from the menu or

closes the adjustment menu.
Returns to the previous menu.

EXIT

MagicInfo

Exits from the menu screen.

MagicInfo Quick Launch Button.

Note

This button is disabled for products that do not support

MagicInfo.

Mechanical Layout
Mechanical Layout

LCD Display Head

Introduction

Installation VESA Bracket

• When installing VESA, make sure to comply with the international VESA standards.

• Purchasing VESA Bracket and Installation Information : Please contact your nearest

SAMSUNG Distributor to place an order. After your order is placed, installation profes­sionals will visit you and install the bracket.

• At least 2 persons are needed in order to move the LCD Display.

• SAMSUNG is not responsible for any product damage or any injury caused by installation

at customer's discretion.

Dimensions

Introduction

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length.

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to

customers when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when

installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Introduction

Wall Bracket(1) Hinge(Left 1, Right1)Plastic

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1. Insert and tighten the Captive Screw in the direction of the arrow.

When done, mount the wall bracket on the wall.

Hanger
(4)

Screw
(A)(11)

Screw
(B)(4)

Anchor
(11)

There are two hinges(left and right). Use the correct one.

A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)

2. Before drilling into the wall, check if the length between the two locking holes at the back

of the product is correct.

Introduction

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.

A - Length between the two locking holes

3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit

to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)

1. Remove the 4 screws on the back of the product.

Introduction

2. Insert the screw B into the plastic hanger.

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the
holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.

3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

A - LCD Display
B - Wall Bracket
C - Wall

Wall Bracket Angle Adjustment

Introduction

Adjust the bracket angle to -2° before installing it on the wall.

1. Fix the product to the wall bracket.

2. Hold the product at the top in the center and pull it forward (direction of the arrow) to
adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.

Connections

Connecting a Computer

There are several ways to connect the computer to the monitor. Choose
one from the following options.

Using the D-sub (Analog) connector on the video card.

• Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the
back of your LCD Display and the 15 pin D-sub Port on the computer.

Using the DVI (Digital) connector on the video card.

• Connect the DVI Cable to the [DVI IN] port on the back of your LCD
Display and the DVI port on the computer.

Using the DP (Digital) connector on the video card.

• Connect the [DP IN] port on the LCD Display to the DP port on the PC
using the DP cable.

Connections

Using the HDMI (Digital) connector on the video card.

• Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on
the PC using the HDMI cable.

Note

Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input
source when connected to the PC via an HDMI cable.

To obtain normal picture and audio from the PC, HDMI2 (only with a
460UT-2, 460UT-B model) or HDMI1 must be selected before PC is se­lected in Edit Name.

To enable audio when DVI Device is selected, be sure to establish the
connection using step ( ).

Connect the Audio cable for your LCD Display to the Audio port on the
back of the LCD Display.

Connect the power cord for your LCD Display to the Power port on the
back of the LCD Display. Turn on the power switch.

Note

Contact a local SAMSUNG Electronics Service Center to buy optional items.

Connecting to Other devices

Note

• AV input devices such as DVD players, VCRs or camcorders as well as your computer
can be connected to the LCD Display. For detailed information on connecting AV input
devices, refer to the contents under Adjusting Your LCD Display.

• The LCD Display 's configuration at the back may vary slightly depending on the LCD
Display model.

Connecting an External Monitor

Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and

the input port on another monitor using a DVI cable.

Connect between the [AUDIO OUT] port on the LCD Display and the audio

input port on another monitor using a stereo cable.

Note

Select DVI Mode as an input source for the external monitor connected to [DVI OUT].
DVI OUT does not support HDCP.

Connecting AV Devices

Connections

1. Connect an audio cable to [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on
the product and the audio port on an external device such as a VCR or
DVD player.

2. Connect a video cable to [AV IN] on the product and the video output port
on the external device.

3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

4. Press SOURCE on the product or remote control and select "AV".

Note

AV input devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the LCD Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your LCD Display.

Connecting to a Camcorder

1. Locate the AV output jacks on the camcorder. They are usually found on
the side or back of the camcorder. Connect a video cable between the
VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Dis­play .

Connections

2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the
camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the
LCD Display .

3. Press SOURCE on the product or remote control and select "AV".

4. Then, start the Camcorders with a tape inserted.

Note

The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
If your camcorder is stereo, you need to connect a set of two cables.