Samsung 460UTN-2, SYNCMASTER 460UT-2, 460UT-2, SYNCMASTER 460UTN-2 User Manual

SyncMaster 460UTn-2, 460UTn2-UD2, 460UT-2, 460UTn-B, 460UT-B

LCD Display

User Manual
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.

Safety Instructions

Notational

These safety instructions must be followed to ensure your safety and prevent property dam­age.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Power

Prohibited
Do not disassemble
Do not touch
When not used for extended period of time, set your computer to DPM.
If using a screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
Important to read and under­stand at all times
Disconnect the plug from the outlet
Ground to prevent an electric shock
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power out-
let.
Otherwise, it may result in electric shock or personal injury.
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
Otherwise, this may result in damage to the product due to electric shock.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

Installation

Otherwise, this may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the provided power cord of another product.
Otherwise, this may result in fire or electric shock.
Connect the power plug to a wall outlet that can be easily reached.
When a problem occurs with the product, you must unplug the
power plug to cut the power off completely. You cannot cut the power off completely using only the power button on the prod­uct.
Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high hu­midity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
Ensure that at least two persons lift and move the product.
Otherwise, it may be dropped and cause personal injury, and/
or damage the product.
When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.
Otherwise, it may fall or cause personal injury.
Use a cabinet or rack of a size appropriate to the product.
Safety Instructions
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIG­ARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
Otherwise, this may result in fire.
Keep heating appliances as far away from the power cord or the product as possible.
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or closet.
Otherwise, this may result in fire due to an increase in the in-
ternal temperature.
When putting the product down, make sure to put it down softly.
Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
Otherwise, it may fall and cause personal injury.
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is a clearance of more than 4 inches (10 cm) from the wall.
Otherwise, it may result in fire due to an increase in the internal
temperature.
Ensure that the packaging vinyl is kept away from children.
Otherwise, it may result in serious harm (suffocation) if children
play with it.
If the height of your monitor is adjustable, do not place any ob­ject or part of your body on the stand when lowering it.
This may cause damage to the product or the person carrying
it.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft cloth.
Do not spray cleaner directly onto the surface of the product.
Otherwise, this may result in the discoloration and distortion of
the structure and the screen surface may peel off.
Safety Instructions
When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power cord.
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth.
(Do not use chemicals such as wax, benzene, alcohol, thinner,
mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indica­tion labels on the product.
Since the product housing is easily scratched, make sure to use the specified cloth only.

Others

When cleaning the product, do not spray water directly onto the main body of the product.
Ensure that water does not enter the product and that it is not
wet.
Otherwise, this may result in electric shock, fire or a malfunc-
tion.
The product is a high voltage product. Do not disassemble, re­pair or modify the product yourself.
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and con­tact a Service Center.
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.
Otherwise, this may result in electric shock or fire.
Safety Instructions
If thunder or lightning is occurring, do not touch the power cord or antenna cable.
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain.
Otherwise, it may result in fire due to an increase in the internal
temperature.
Do not place any containers containing water, vases, flower­pots, medicines as well as any metal on the product.
If water or a foreign material enters the product, disconnect the
power cord and contact a Service Center.
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the product.
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output termi­nals, etc).
If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur.
If you are not using your product for a long period of time, put
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high.
Having the sound too loud may damage your hearing.
Safety Instructions
To avoid eyestrain, do not sit too close to the product.
Take a rest for at least five (5) minutes after using the monitor for one (1) hour.
This reduces eye fatigue.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Otherwise, it may fall and cause personal injury and/or damage
the product.
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the product.
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the power cord from the power outlet.
Otherwise, this may result in overheating or fire due to dust,
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.
Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a lo­cation that children or infants cannot reach.
If children have had the battery in their mouths, consult your
doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
Otherwise, the battery may become damaged or it may cause
fire, personal injury or damage due to leakage of the internal liquid.
Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.
Otherwise, the batteries may be damaged or cause fire, per-
sonal injury or damage due to a leakage of the internal liquid.
Safety Instructions
The batteries (and rechargeable batteries) are not ordinary re­fuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
The customer can return used or rechargeable batteries to a
nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.
This may reduce the lifetime of the product, and may result in
fire.
Do not drop any objects onto the product or cause any impact to the product.
Otherwise, this may result in electric shock or fire.
Do not use a humidifier near the product.
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug; ventilate immediately.
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the stand.
This may result in personal injury as your hand or fingers may
become caught.
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children to reach.
Otherwise, it may fall and result in personal injury.
Since the front part of the product is heavy, install the product
on a level and stable surface.
Safety Instructions
Do not put any heavy objects on the product.
This may result in personal injury and/or damage to the prod-
uct.

Introduction

Package Contents

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.
Lift up the package box by
both sides of the package
After unpacking the package, make sure to check the contents of the package.
Store the packaging box in case you need to move the Product later.
If any items are missing, contact your dealer.
Contact a local dealer to purchase optional items.

Unpacking

holding the grooves on
box.
Check the contents of the
package.
Remove the Styrofoam
and vinyl cover.
LCD Display
Manuals
Introduction
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
MagicInfo Software CD,
MagicInfo Manual CD
(Applicable to the
460UTn-2, 460UTn2-UD2,
460UTn-B model only)
Cables
Power Cord D-Sub Cable
Others
User Manual
Remote Control
(BP59-00138B)
Sold separately
Semi Stand KIT LAN Cable USB Cable
Batteries (AAA X 2)
(Not available in all loca-
tions)
(Applicable to the
460UTn-2, 460UTn2-UD2,
460UTn-B model only)
Introduction
Sold separately
RGB to BNC Cable RGB to Component Cable Network Box
(Applicable to the
460UT-2, 460UT-B model
Wall Mount KIT TV Tuner Box
only)
Accessories that can be purchased with the product vary by country.
Your LCD Display Front
SOURCE button
Switches from PC mode to Video mode. Selects the input source that an external device is connected to.
[PC] → [DVI] →
[DisplayPort] → [MagicInfo] → [TV]
[AV] → [Component] → [HDMI1] → [HDMI2] →
A TV tuner box (sold separately) must be connected to use the TV.
A network box (sold separately) must be connected to use MagicInfo
with a 460UT-2, 460UT-B model.
POWER button
Use this button for turning the LCD Display on and off.

Rear

Introduction
Power indicator
Shows PowerSaver mode by blinking green
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
See the "Connections" section for details about cable connections. The LCD Display's con­figuration at the back may vary slightly depending on the model.
POWER S/W ON [
Switches the LCD Display On/Off.
POWER
The power cord plugs into the LCD Display and the wall outlet.
IR OUT/IN
Receives a signal from the remote control and outputs the signal through Loopout when a removable sensor board is connected.
AMBIENT SENSOR IN
Supplies power to the removable sensor board and receives a signal from the light sensor.
DVI OUT (LOOPOUT)
] / OFF
Introduction
Connect a monitor to another monitor through a DVI, DVI to HDMI cable.
Connect a DVI or DVI-HDMI cable to [DVI
OUT (LOOPOUT)] on the product and [DVI IN] or [HDMI IN] on another monitor.
HDMI and network signals sent via the
[DVI OUT(LOOPOUT)] port are dis-
played on the second display which has
the [DVI IN] port.
The Loopout function can be used to du­plicate the screen of the primary display.
Connect [DVI OUT] on the primary dis-
play to display.
A maximum of 100 monitors can be con­nected to DVI-Loopout (using a 2m-long DVI cable). Up to HD resolution can be supported. Compatible input sources in­clude DVI IN, HDMI IN 1, and HDMI IN 2 (MagicInfo).
[DVI IN] or [HDMI] on another
The status of the cable may have a great effect on the Loopout performance.
RGB/COMPONENT IN (PC/COMPO-
NENT Connection Terminal (Input))
Connect the [RGB/COMPONENT IN]
port on the monitor to the RGB port on the PC using the D-SUB cable.
Connect the [RGB/COMPONENT IN]
port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable.
Connect the [RGB/COMPONENT IN]
port on the monitor to the BNC port on the PC using the RGB to BNC cable.
DVI IN (PC Video Connection Terminal)
Connect the [DVI IN] port on the monitor to
the DVI port on the PC using the DVI cable.
RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/ DP/HDMI Audio Connection Terminal (In­put))
Connect the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the monitor and the speaker
Introduction
output terminal of your computer's sound card using a stereo cable (sold separately).
DP IN
Receives a signal from the Display port.
Connect a DP cable to [DP IN] on the product
and DP IN on another display.
AV/COMPONENT AUDIO IN [R-AUDIO-
L] Connect the [AV/COMPONENT AUDIO IN
[R-AUDIO-L]] port on the monitor to the audio
output port on the PC or on the external de­vice using an audio cable.
AV IN Connect the [AV IN] terminal of your monitor
to the video output terminal of the external device using a VIDEO cable.
AUDIO OUT
Connect a headphone or an External speak­er.
DC OUT
Make sure to use connecting [DC OUT] ter-
minal to the authorized TV-Tuner Box [SBB_DTC/ZA].
Otherwise, this may result in damage
to the product.
HDMI IN 1
Connect the [HDMI IN 1] terminal at the
back of your LCD Display to the HDMI terminal of your digital output device us­ing a HDMI cable.
Up to HDMI 1.3 can be supported.
A normal external device (DVD player or
camcorder, etc.) or a TV tuner box can be
connected to the [HDMI IN 1] terminal.
To use a TV tuner box, make sure to con-
nect it to the [HDMI IN 1] terminal.
Introduction
HDMI IN 2 (MAGICINFO)
Connect the [HDMI IN 2 (MAGICINFO)]
terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.
Up to HDMI 1.3 can be supported.
The MAGICINFO OUT port must be connec-
ted to the [HDMI IN 2 (MAGICINFO)] port.
RJ 45 MDC (MDC PORT)
MDC(Multiple Display Control) Program Port
Connect the LAN cable to [RJ45 MDC] on the
product and LAN on the PC. To use an MDC, the MDC program must be installed on the PC.
Go to Multi Control and select RJ45 MDC as the MDC Connection.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
Connect a serial cable (cross type) to
[RS232C] on the product and RS232C on the
PC. To use an MDC, the MDC program must be installed on the PC.
Go to Multi Control and select RS232C MDC as the MDC Connection.
RGB OUT
MagicInfo video output port
Applicable to the 460UTn-2, 460UTn2-UD2, 460UTn-B model only.
MAGICINFO OUT
Outputs MagicInfo DP signals. It should be connected to [HDMI IN 2 (MAGICINFO)] via
a DP to HDMI cable.
Introduction
LAN (LAN Connection Terminal)
Connects to a LAN cable to allow Internet or
network access in MagicInfo mode.
Applicable to the 460UTn-2, 460UTn2-UD2, 460UTn-B model only.
USB (USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.
Applicable to the 460UTn-2, 460UTn2-UD2, 460UTn-B model only.
Kensington Lock slot
A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the man­ufacturer, for more information, refer to the User Manual supplied with the locking device for more information.
To lock the product, follow these steps:
1. Wrap the Kensington lock cable around
a large, stationary object such as a desk or chair.
2. Slide the end of the cable with the lock
attached through the looped end of the Kensington lock cable.
3. Insert the Kensington Lock into the se-
curity slot ( ) on the back of the dis­play.
4.
Lock the lock ( ).
You must purchase the Kensington Lock
separately.
These are general instructions. For exact
instructions, see the User Manual sup­plied with the locking device.
Introduction
You can purchase the locking device
from an electronics store, an online shop, or our service center.
See the "Connections

Remote Control

The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen­cy.
" section for details about cable connections.
POWER
OFF
Number Buttons
DEL / GUIDE button
+ VOL -
SOURCE
D.MENU
TOOLS
Up-Down Left-Right buttons
POWER
OFF
INFO
The Color button and the PC/DVI/HDMI/DP
selection button
TTX/MIX
MTS/DUAL
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
MagicInfo
Turns the product On/Off.
Turns the product Off.
Introduction
Number Buttons
DEL / GUIDE button
+ VOL -
SOURCE
D.MENU
TOOLS
Used to enter the password during the OSD adjustment or to use MagicInfo.
Press to change the channel.
The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.
- This function does not work for this LCD Display.
Adjusts the audio volume.
Selects a connected external input source or MagicInfo
mode.
Press the button to change the input signal SOURCE.
Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time.
DTV menu display
- This function does not work for this LCD Display.
Use to quickly select frequently used functions.
- This function does not work for this LCD Display.
Up-Down Left-Right but-
tons
INFO
The Color button and the PC/DVI/HDMI/DP selection button
TTX/MIX
MTS/DUAL
Moves from one menu item to another horizontally, vertically or adjusts selected menu values.
Current picture information is displayed on the upper left corner of the screen.
In TV mode, these buttons can be used for setting the broadcasting announcement function of a digital channel.
You can select the PC, DVI, HDMI or DP(DisplayPort) ex-
ternal input directly in a mode other than TV mode.
TV channels provide written information services via tele­text.
- Teletext Buttons
- This is activated when a TV tuner box is installed.
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
FM Stereo Mono Mono Manual
Stereo
SAP
Mono Stereo Mono SAP
Change
Mono
DUAL-
Introduction
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV.
- This is activated when a TV tuner box is installed.
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
This button is used to return to the immediately previous channel.
- This is activated when a TV tuner box is installed.
Pauses (mutes) the audio output temporarily. This is dis­played on the lower left corner of the screen. The audio comes back on if MUTE or - VOL + is pressed in the Mute mode.
In TV mode, selects TV channels.
- This is activated when a TV tuner box is installed.
Selects the TV mode directly.
- This is activated when a TV tuner box is installed.
Opens the on-screen menu and exits from the menu or closes the adjustment menu.
Returns to the previous menu.
Exits from the menu screen.
MagicInfo
Mechanical Layout Mechanical Layout
MagicInfo Quick Launch Button.
Note
This button is disabled for products that do not support
MagicInfo.

LCD Display Head

Introduction

Installation VESA Bracket

When installing VESA, make sure to comply with the international VESA standards.
Purchasing VESA Bracket and Installation Information : Please contact your nearest
SAMSUNG Distributor to place an order. After your order is placed, installation profes­sionals will visit you and install the bracket.
At least 2 persons are needed in order to move the LCD Display.
SAMSUNG is not responsible for any product damage or any injury caused by installation
at customer's discretion.
Dimensions
Introduction
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Wall Bracket Installation

Contact a technician for installing the wall bracket.
SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Introduction
Wall Bracket(1) Hinge(Left 1, Right1)Plastic
Wall Bracket Assembly
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
Hanger (4)
Screw (A)(11)
Screw (B)(4)
Anchor (11)
There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)
2. Before drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Introduction
A - Length between the two locking holes
3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)
1.
Remove the 4 screws on the back of the product.
Introduction
2. Insert the screw B into the plastic hanger.
Notice
Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.
Be careful when installing the product on the bracket as fingers can be caught in the holes.
Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.
3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A - LCD Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment
Introduction
Adjust the bracket angle to -2° before installing it on the wall.
1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
You can adjust the bracket angle between -2° and 15°.
Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Connections

Connecting a Computer

There are several ways to connect the computer to the monitor. Choose one from the following options.
Using the D-sub (Analog) connector on the video card.
Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the
back of your LCD Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the [DVI IN] port on the back of your LCD
Display and the DVI port on the computer.
Using the HDMI (Digital) connector on the video card.
Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on
the PC using the HDMI cable.
Connections
Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input
source when connected to the PC via an HDMI cable.
To obtain normal picture and audio from the PC, HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 must be selected before PC is se­lected in Edit Name.
To enable audio when DVI Device is selected, be sure to establish the
connection using step (
Connect the Audio cable for your LCD Display to the Audio port on the back of the LCD Display.
Connect the power cord for your LCD Display to the Power port on the back of the LCD Display. Turn on the power switch.
Contact a local SAMSUNG Electronics Service Center to buy optional items.

Connecting to Other devices

AV input devices such as DVD players, VCRs or camcorders as well as your computer
can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display.
The LCD Display 's configuration at the back may vary slightly depending on the LCD
Display model.

Connecting an External Monitor

).
Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and
the input port on another monitor using a DVI cable.
Connect between the [AUDIO OUT] port on the LCD Display and the audio
input port on another monitor using a stereo cable.
Select DVI Mode as an input source for the external monitor connected to [DVI OUT].
DVI OUT does not support HDCP.

Connecting AV Devices

Connections
1. Connect an audio cable to [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on
the product and the audio port on an external device such as a VCR or DVD player.
2. Connect a video cable to [AV IN] on the product and the video output port
on the external device.
3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
4. Press SOURCE on the product or remote control and select "AV".
AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display.

Connecting to a Camcorder

1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the
VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Dis-
play .
Connections
2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the
camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the
LCD Display .
3. Press SOURCE on the product or remote control and select "AV".
4. Then, start the Camcorders with a tape inserted.
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
If your camcorder is stereo, you need to connect a set of two cables.
Loading...
+ 115 hidden pages