Samsung 403Tn User Manual

Install Pro

rams

SyncMaster 403Tn

Power

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

This may cause fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust.

Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

The monitor may cause injury by falling.

Set down the monitor carefully.

The monitor could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

Installation by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

Leave a space for ventilation between the product and the wall.

Poor ventilation may cause the interior temperature to rise and lead to fire.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

A dirty connector may cause an electric shock or fire.

Others

Contact the Service Center or Customer Center for interior cleaning once a year.

Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or fire.

Do not remove cover (or back).

This may cause an electric shock or fire.

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to moisture.

z This may cause malfunctio n, an electric shock or fire.

Especially avoid operating the monitor near water or outdoors where it could

be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord.

The monitor may malfunction, causing an electric shock or fire.

Then contact the Service Center .

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause malfunction, an electric shock or fire.

z If a foreign substance enters the monitor, unplug the power cord and

contact the Service Center.

Do not use or store inflammable substances near the monitor.

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

This may cause an electric shock, fire or injury.

Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor.

This may cause malfunction, an electric shock or fire.

z Always contact the Service Center if foreign substances/objects enter into

the monitor.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

Change the mode to energy save or set a screensaver to moving picture

when you need to be away from the monitor for an extended period of time.

Be careful when adjusting the stand angle.

z Applying too much force may cause the monitor topple over or fall, resulting

in injury. Your hand or finger(s) may get caught between the monitor and the stand,

causing injury.

Adjust the resolution and frequency to the levels appropriate for the model.

Inappropriate resolution may cause undesirable picture quality.

40 inch - 1280 X 768

Sitting too close to the monitor on a continuous basis may damage eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

Do not use the monitor where it may be exposed to strong vibrations.

z Exposure to strong vibrations may be fire hazard and shorten the life of the

monitor.

When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected devices, are disconnected before moving the monitor.

Failure to disconnect cables may damage it and lead to fire or an electric

shock.

When you remove batteries from the remote, be careful that they are not swallowed by children. Keep batteries out of the reach of children.

If swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position as indicated on battery holder.

Incorrect polarity may cause a battery to break or leak and could lead to fire,

injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries together.

z This may cause a battery to break or leak and could lead to fire, injury, or

contamination (damage).

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer

Contact a local deale

to buy optional items.

Unpacking

Manual

Quick Setup Guide

Monitor

Warranty Card

(Not available in all locations)

User's Guide, MDC software,

Natural Color software,

icNet software

Cable

D-Sub Cable Power Cord RS232C Cable

LAN Cable

Sold se

aratel

Wall Mount KIT Speaker Set Stand KIT

Bracket VESA Bracket

Screw (22EA)

MACHINE : M5 x L22

DVI Cable

Others

Remote Control Batteries (AAA X 2) Cover-hole

BNC to RCA

terjack

Ada

Semi Stand

Screw (4EA)

MACHINE : M4 x L15

Front

1. MENU 6. PIP

2. Navigate button (Up-Down button) 7. Power button

3. Adjust button (Left-Right button)/ Volume button

4. ENTER 9. Remote Control Sensor

5. SOURCE

1. MENU

Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.

2. Navigate button (Up-Down button)

Moves from one menu item to another vertically or adjusts selected menu values.

3. Adjust button (Left-Right button) / Volume button

Moves from one menu item to another horizontally or adjusts selected menu values. Also adjusts the audio volume.

4. ENTER

5. SOURCE

6. PIP

Activates a highlighted menu item.

Switches from PC mode to Video mode. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] [BNC] [DVI] [AV] [S-Video] [Component] [MagicNet]

>>Click here to see an animation cl ip

Push the PIP button to turn PIP screen On/Off. More than one PIP couldn't be overlapped on screen as BNC and the component use the same terminal.

>>Click here to see an animation cl ip

• PC / DVI

: AV / S-Video / Component Mode

• BNC

: AV / S-Video Mode

8. Power indicator

• AV / S-Video

: PC / BNC / DVI Mode

• Component

: PC / DVI Mode

7. Power button

Use this button to turn the monitor on and off.

8. Power indicator

Power Indicator shows PowerSaver mode by green blinking.

9. Remote Control Sensor

Aim the remote control towards this spot on the Monitor.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.

Rear

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model.

1. POWER S/W

2. POWER IN

3. RS232C OUT/IN (RS232C Serial PORT):

MDC(Multiple Device Control) Program Port

4. PC IN(RGB) (PC Video Connection Terminal)

Using D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)

5. DVI IN(HDCP) (PC Video Connection Terminal)

Using DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)

6. PC/DVI/BNC AUDIO IN (PC/DVI/BNC Audio Connection Terminal (Input))

7. COMPONENT AUDIO IN [R-AUDIO-L](Component Audio Connection Terminal (Input))

8. BNC/COMPONENT OUT (BNC/Component Connection Terminal (Output))

- BNC (Analog PC) Connection : connecting R, G, B, H, V port

- Component Connection : connecting P

R, Y, PBport

9. BNC/COMPONENT IN (BNC/Component Connection Terminal (Input))

10. AV OUT [VIDEO](VIDEO Connection Terminal) : AV mode (Output)

11. AV IN [VIDEO](VIDEO Connection Terminal) (Input)

12. AV OUT [S-VIDEO](S-Video Connection Terminal) : S-Video mode (Output)

13. AV IN [S-VIDEO](S-Video Connection Terminal) (Input)

14. MONITOR [R-AUDIO-L](Monitor Audio Connection Terminal (Output))

- MONITOR OUT is the terminal for sound output of PC, DVI or BNC.

15. AV IN [R-AUDIO-L](Monitor Audio Connection Terminal (Input))

The number of monitor that can be connected to loopout may be different under the circumstance such as cable, signal source, etc. With a cable which there is no degradation or signal source ten monitors can be connected.

16. DIGITAL AUDIO OUT (Digital Audio Connection Terminal)

17. USB (USB Connection Terminal)

(Keyboard / Mouse, Mass Storage Device Compatible.)

18. LAN (LAN Connection Terminal)

(MS Internet Explorer)

19. EXT SPEAKER(8 Ω) (EXT Speaker Connection Terminal)

20. Kensington Lock

See Connecting the Monitor for further information regarding cable connections.

Remote Control

The performance of the remote control may be affected by a TV or other electronic device operated near

the monitor, causin

malfunction due to interference with frequency.

1. POWER

2. MagicNet buttons

3. +100

4. VOL

5. MUTE

6. AUTO

7. MENU

8. ENTER

9. PRE-CH

10. CH/PAGE

11. SOURCE

12. INFO

13. EXIT

14. Up-Down Left-Right buttons

15. P.MODE (M/B)

16. STILL

17. BBE

18. MTS

19. PIP

20. SOURCE

21. SIZE

22. SWAP

23.

24.

25.

26.

1. POWER

Use this button for turn the monitor on and off.

2. MagicNet buttons

- Used for MagicNet.

MagicNet Remote Control

Alphanumeric: Used to enter the Internet address.

DEL : Functions as the backspace.

SYMBOL : Used to enter the symbols. (.O_-:/)

ENTER : Used to enter values.

3. +100

Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1".

- This fuctions does not work for this monitor.

4. VOL

Also adjusts the audio volume.

>>Click here to see an animation cl ip

5. MUTE

Pauses (mutes) the audio output temporarily. Displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode.

6. AUTO

Adjusts the screen display automatically. If you change resolution in the control panel, Auto function will be executed.

7. MENU

Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.

8. ENTER

Activate a highlighted menu item.

9. PRE-CH

This button is used to return to the imm ed ia tel y prev i ou s ch an ne l.

- This fuctions does not work for this monitor.

10. CH/PAGE

Selects channels or page.

- This fuctions does not work for this monitor.

11. SOURCE

Push the button, selects the Video source changes.

12. INFO

Current picture information displays on the upper left corner of the screen.

13. EXIT

Exits from the menu screen.

14. Up-Down , Left-Right buttons

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

15. P.MODE (M/B)

When you press this button, current picture mode is displayed on the lower center of the screen.

AV / S-Video / Component : P.MODE

The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic Standard Movie Custom )

PC/DVI/BNC : M/B (MagicBright™)

MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. (Entertain Internet Text Custom )

16. STILL

When you press this button, STILL is displayed on the lower center of the screen. Press the button once to freeze the screen. Press it again to unfreeze.

17. BBE

Recreates the natural sound and improves sound clarity through boosting high and low range frequencies. As a result high sounds are clearer, brilliant and finely detailed while low sounds are tight, well-defined and harmonically rich.

18. MTS

You can select the MTS (Multichannel Television Stereo) mode.

- This fuctions does not work for this monitor.

19. PIP

Every time you push the button, activate a PIP screen.

20. SOURCE

The PIP window's signal source changes.

Audio Type MTS/S_Mode Default

Mono Mono

FM Stereo

Stereo

SAP

Mono Stereo

Mono SAP

Manual Change

Mono

21. SIZE

You can switch the Picture Size.

22. SWAP

Swapping the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window.

23.

Rewind

24.

Stop

25.

Play/Pause

26.

Fast forward

Remote Control

PHOTO

z When the files are selected in the library list

Previous file

Stop slideshow / View the bottom menu bar

Slideshow

Next file

z When you see no menu in a zoomed-in picture

MUSIC

Move up to the top of the image

Move down to the bottom of the image

Move to the left of the image

Move to the right of the image

z When the files are selected in the library list

File view on the cursor position / Play / Pause during playback

Stop playing

Play in 5 seconds

Play 5 seconds earlier

Move to the next page (when the cursor is placed at the top, it will go back to the last file of the previous page)

Move to the previous page (when the cursor is placed at the bottom, it will move to the first file of the next page)

MOVIE

Move to the next page (when the current page is the first, it will move to the last page)

Move to the previous page (when the current page is the last, it will move to the first page)

File view on the cursor position Play

z When the files are selected in the library list

Move to the top (when the cursor is placed at the top, it will go back to the last file of the previous page)

Move to the bottom (when the cursor is placed at the bottom, it will move to the first file of the next page)

Move to the next page (when the current page is the first, it will move to the last page)

Move to the previous page (when the current page is the last, it will move to the first page)

File view on the cursor position Play

z Play

Play / Pause during playback

OFFICE

Stop playing

Play 5 seconds earlier

Play in 5 seconds

z When the files are selected in the library list

Move to the top (when the cursor is placed at the top, it will go back to the last file of the previous page)

Move to the bottom (when the cursor is placed at the bottom, it will move to the first file of the next page)

Move to the next page (when the current page is the first, it will move to the last page)

Move to the previous page (when the current page is the last, it will move to the first page)

File view on the cursor position

z PDF

Move to the top

Move to the bottom

Move to the next page

Move to the previous page

Exit PDF

z Excel

Move to the upper cell

Move to the lower cell

Move to the left cell

Move to the right cell

Move to the next page

Move to the previous page

Move to the right sheet

Move to the left sheet

Exit Excel

Power point Normal

Move to the top

Move to the previous page

Move to the next page

z Power point Slideshow

Move to the previous page

Slideshow

Exit Power point

Stop slideshow

Move to the top

Move to the bottom

Move to the next page

Move to the previous page

z Word

z HTML / Ineternet

Exit Power point

Move to the top

Move to the bottom

Move to the next page

Move to the previous page

Exit Word

Move the mouse cursor up

Move the mouse cursor down

Move the mouse cursor to the left

Move the mouse cursor to the right

Click when the cursor is placed over a link (move to the link)

Exit the Internet

Mechanical Lay-out | Monitor Head | Stand | Speaker | Mounting Bracket | How To Install VESA Bracket

1. Mechanical Lay-out

2. Monitor Head

3. Stand

4. Speaker

5. Mounting Bracket

6. How To Install VESA Bracket

This installation guide is for the 40" LCD Monitor Model.

Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung

Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.

z At least 2 persons are needed in order to move the LCD Monitor.

Samsung is not responsible for any product damage or any injury caused by installation at customer's

discretion.

Parts

Please use provided components and parts only.

Main Bracket VESA Bracket

How To Install the LCD Monitor on the Bracket

Assemble the Main Bracket and secure it using screws. Each 3 screws securing parts of the left bracket should form a right-angled triangular shape. Each 3 screws securing

Machine Screws

(1):16 EA

M5 X L20(BLACK)

Machine Screws

(2):6 EA

M5 X L12(SILVER)

parts of the right bracket should form a regular triangular shape.

Machine Screw(1)

For the bracket assembly, locate parts properly by

distinguishing them using inlayed L(left), R(right), TOP

(top), and BOT(bottom) markings.

Fix the VESA Bracket onto the assembled Main Bracket. Be sure that the VESA Bracket is placed correctly not to confuse front and back side of the VESA bracket.

Machine Screw(2)

Secure the bracket onto the backside of the LCD Monitor using screws.

Machine Screw(1)

Dimensions

For securing the bracket on a wall, use only machi ne screws of 6 mm diameter and 8 to 12 mm length.

Installing Stand Kit

Only the supplied bolts should be used.

Samsung Electronics will not be responsible for damages caused by using a base other than those specified.

1. Installing the Semi Stand

Left stand Right stand

1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or stand kit (sold separately) and cover the hole using the 'Cover-hole' when attaching the wall mount kit.

2. Set up the left and right stands respectively.

3. Put the stand into the hole at the bottom of the monitor. Insert screw into the hole indicated and tighten. (M4 × L15)

The Semi Stand is provided only for screen adjustment before the stand kit or wall mount kit (sold separately) is attached. The Semi Stand is not intended for use as a regular stand and Samsung Electronics is not responsible for any problems caused by using it instead of the regular products. Never use the Semi Stand as the regular stand.

2. Installing Stand Kit (sold separately)

2. Make sure you put the parts in the right direction and in the right place. (M4 × L15)

3. Put the stand into the hole at the bottom of the monitor.

4. Insert screw into the hole indicated and tighten. (M4 × L15)

AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under

Adjusting Your Monitor.

1. Connecting to a Computer

1. Connect the power cord for your monitor to the power port on the back of the monitor. Trun on power switch.

2. There are 3 ways to connect the signal cable to your monitor. Choose one of the followings :

Using the D-sub (Analog) connector on the video card.

2-1.

Connect the signal cable to the

Using the DVI (Digital) connector on the video card.

2-2.

15 pin D-sub Port

Connect the DVI Cable(DVI-D + DVI-D) to the

on the back of your monitor.

DVI Port

on the back of your Monitor.

Using the BNC (Analog) connector on the video card.

2-3.

Connect the BNC Cable to the Monitor and the

15 pin D-sub Port

BNC/COMPONENT IN - R, G, B, H, V port

on the computer.

DVI cable or BNC cable is optional.

3. Connect the audio cable for your monitor to the audio port on the back of your computer.

4. Turn on both your computer and the monitor.

Contact a local Samsung Electronics service center to buy optional items.

2. Connecting to a VCR

on the back of your

1. AV input devices like VCRs or Camcorders are connected to the

of the monitor using the S-VHS or BNC cable.

VIDEO]

AV IN [VIDEO]

S-VHS or BNC cable is optional.

2. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the monitor's

IN [R-AUDIO-L]

using audio cables.

3. Select AV or

S-Video

that is connected to a VCR or Camcorders using the Source button on the

monitor's front or remote control.

4. Then, start the VCR or Camcorders with a tape inserted.

3. Connecting to a DVD Player

AV IN [S-

MONITOR

1. Connect a set of audio cables between the and the AUDIO OUT jacks on the DVD player.

2. Connect a Component cable between the and the P

R, Y, PB jacks on the DVD player.

BNC/COMPONENT IN - P

Component cable is optional.

3. Select

Component

that is connected to a DVD player using the Source button on the monitor's

front or remote control.

4. Then, start the DVD Player with a DVD disc inserted.

For an explanation of Component video, see your DVD player owner's manual.

4. Connecting a Camcorder

COMPONENT AUDIO IN [R-AUDIO-L]

, Y, PB port

on the Monitor

+ 82 hidden pages