Samsung 320P User Manual

 

SyncMaster 320P

Notational

Model

Failure to follow directions noted by this symbo l could result in bodily harm or damage to the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not tou ch Ground to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS. If using a screen sa ver, set it to active screen mode.

Do not use a damaged or loose plug.

This may cause electric s hock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose.

A bad co nnection may cause fire.

Do not bend the plug excessively and wire nor place heavy objects upon them, which could cause damage.

This may cause electric s hock or fire.

Do not connect too many extension cords or plugs to one outlet.

z This may cau se fi re.

Do not disconnect the power cord while using the monitor.

z A surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

z If the connector or plug of the power cord is dusty, clean it with a dry cloth.

Using the power cord with a dusty plug or connector may cause electric shock or fire.

Installation

Be sure to contact an authorized the Service Center, when installing your monitor in a

location with heavy dust, high or low temperatures, high humidity, and exposed to chemical su bstances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of dust.

Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or on a shelf so that the end of the base does not protrude from the showca se or shelf.

Dropping the product may cause damage to the product or the person carrying it.

Do not place the product on an unstable or s mall surface area.

z Place the product on an even and stable surface , as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

z Take care, as someo ne, specifically children may trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes away from the product.

Otherwise, this may cause fire.

Keep any heating devices away from the power cable.

z A melted coating may cause electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

z Any increase in the internal temperature may cause fire.

Put down the monitor carefully.

Failing to do so may damage the monitor.

Do not place the m onitor face down.

z This may damage the TFT -LCD surface.

The installation of the bracket must be done by a qualified professional.

Installing the bracket by unqualified personnel may result in injury.

z Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.

Poor ventilation may cause an increase in the internal tempe rature of the product, resulting in a shortened component life and degraded performance.

Clean

Keep the plastic packaging (bag) out of children’s reach.

The plastic packaging (bag) may cause suffocation if children play with it.

When clean ing the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

A dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

z Otherwise, this may cau se electric s hock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

z Do not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year.

z Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may caus e a malfunction or fire.

Others

Do not remove the cover (or back).

z This may cause electric shock or fire.

Refer to a qualified servicing company.

If your monitor d oes not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center.

z This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

z This may cause a malfunction, electric shock or fire.

In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center.

The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.

z Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause a malfunction, electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.

Keep the product away from combustible chemical sprays or inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

This may cause electric s hock, fire or injury.

Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports or etc.

This may cause electric s hock or fire. If an alien substanc es or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.

When viewing a fixed screen for an ext ended period of time, residual image or blurriness may appear.

z Change the mode to energy save or set a screensaver to move the picture

when away from the monitor for an extended period of time.

Adjust the resolution and frequency to the level appropriate for the model.

An inappropriate resolution may cause undesirable picture quality.

32 inch (80 cm) - 1360 X 768

iewing the monitor continuously at a too close angle may result in damage

to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

z Dropping the product may cause damage to the product or the person

carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected b efore moving the monitor.

z Failure to disconnect cables may damage it and cause fire or electric

shock.

Make sure there are more than two people when moving the product.

Dropping the product may cause a malfunction or injury to the person carrying it.

Place the product out of children’s reach, a s they could damage by hanging onto it.

A falling product may cause injury to the person or even fatality.

When not using the product for an extended period of time, keep the product unplugged.

Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest on the product.

z Children may try to climb on the product to retrieve an object. The product

could fall, causing causing injury or even fatality.

When removing batteries from the remote control, e nsure that the children

do not s wallow the batteries. Keep the batteries out of children's reach.

If the batteries are swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position as indicated on the battery holder.

z The incorrect polarity may cause a battery to break or leak and may cause

fire, injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries together.

z This may cause a battery to break or leak and may cause fire, injury, or

contamination (damage).

The batteries (and rechargeable batteries) is not ordinary refuse and must be returned for recycling p urposes. The customer is responsible for returning the used or rechargeable batteries for recycling purposes as the consumer.

z The customer can return used or rechargeable batteries to a nearby public

recycling center or to a store selling the same type of the battery or rechargeable battery.

(

)

Model

Please make sure the following items are included with your monitor.

This stand is not for the Floor Standing Type.

Unpacking

Monitor

If any items are missing, contact your dealer.

Contact a local dealer to bu

optional items.

Manual

Quick Setup Guide

Cable

Warranty Card

Not available in all locations

User's Guide, MDC software,

Natural Color software

Sold separatel

D-Sub Cable Power Cord Speaker Wire Cable

Wall Mount KIT Speaker Set Stand KIT

DVI Cable

Other

Remote Control Batteries (AAA X 2) Cover-Hole

BNC to RCA

Ada

ter Jack

Semi Stand

Front

1. MENU 6. PIP

2. Navigate buttons (Up-Down buttons) 7. Power button

3. Adjust buttons (Left-Right buttons)/ Volume buttons

4. ENTER 9. Remote Control Sensor

5. SOURCE

1. MENU

Opens the on-screen menu and exits from the menu or closes the screen adjustment menu.

2. Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

3. Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume.

4. ENTER

Activates a highlighted menu item.

5. SOURCE

Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the monitor at the time. To switch Screen modes: [PC] [BNC] [DVI] [AV] [S-VIDEO] [Component]

>>Click here to see an animation clip

6. PIP

Push the PIP button to turn the PIP screen On/Off. More than one PIP cannot overlap on screen as BNC and the component use the same terminal.

>>Click here to see an animation clip

• PC / DVI : AV / S-Video / Component Mode

• BNC : AV / S-Video Mode

• AV / S-Video : PC / BNC / DVI Mode

• Component : PC / DVI Mode

7. Power button

Turns the monitor On/Off.

8. Power indicator

Shows PowerSaver mode by blinking green.

9. Remote Control Sensor

Aim the remote control towards this spot on the Monitor.

See PowerSaver described in the manual for further information regarding power saving functions. For ener

conservation, turn your monitor OFF when it is not needed or when leaving it unattended

8. Power indicator

for long periods.

Rear

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's configuration at the back may vary slightly depending on the monitor model.

1. RS232C OUT/IN (RS232C Serial PORT): MDC(Multiple Display Control) Program Port

2. DVI IN(HDCP) (PC Video Connection Terminal)

: Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)

3. PC IN(RGB) (PC Video Connection Terminal)

: Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)

4. PC/DVI/BNC AUDIO IN (PC/DVI/BNC Audio Connection Terminal (Input))

5. COMPONENT AUDIO IN [L-AUDIO-R](Component Audio Connection Terminal (Input))

6. BNC/COMPONENT OUT (BNC/Component Connection Terminal (Output))

- BNC (Analog PC) Connection : connecting the R, G, H, V ports.

- Component Connection : connecting the P

, Y, PB ports

7. BNC/COMPONENT IN (BNC/Component Connection Terminal (Input))

8. AV AUDIO IN [L-AUDIO-R](Monitor Audio Connection Terminal (Input))

9. AV OUT [VIDEO](VIDEO Connection Terminal) : AV mode (Output)

10. AV IN [VIDEO](VIDEO Connection Terminal) (Input)

11. AV OUT [S-VIDEO](S-Video Connection Terminal) : S-Video mode (Output)

12. AV IN [S-VIDEO](S-Video Connection Terminal) (Input)

13. EXT SPEAKER(8 Ω) (EXT Speaker Connection Terminal)

14. MONITOR OUT [L-AUDIO-R](Monitor Audio Connection Terminal (Output))

- MONITOR OUT is terminal for the PC sound output.

The number of monitors that can be connected to loopout may may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten monitors can be connected.

15. POWER S/W : Switches the monitor On/Off.

16. POWER IN : The power cord plugs into the

monitor and the wall plug.

17. Kensington Lock

Remote Control

The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase.

See Connecting the Monitor for further information regarding cable connections.

The performance of the remote control may be affected by a TV or other electronic device operating near

the monitor, causin

a malfunction due to interference with the frequency.

1. ON / OFF

2. MAGICNET

3. MDC

4. LOCK

5. MagicNet buttons

6. +100

7. VOL

8. MUTE

9. AUTO

10. MENU

11. ENTER

12. PRE-CH

13. CH/PAGE

14. SOURCE

15. INFO

16. EXIT

17. Up-Down Left-Right buttons

18. P.MODE (M/B)

19. STILL

20. BBE

21. MTS

22. PIP

23. SOURCE

24. SIZE

25. SWAP

26.

27.

28.

29.

1. ON / OFF

Turns the monitor On/Off.

2. MAGICNET

MagicNet Quick Launch Button.

- This fuction does not work for this monitor.

3. MDC

MDC Quick Launch Button.

4. LOCK

Activates or deactivates all function keys on both the remote control and the monitor except for the Power and LOCK buttons.

5. MagicNet buttons

- Used for MagicNet.

Alphanumeric: Used to enter the Internet address.

DEL : Functions as the backspace.

SYMBOL: Used to enter the symbols (.O_-:/).

ENTER : Used to enter values.

- This fuction does not work for this monitor.

6. +100

Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1".

- This fuction does not work for this monitor.

7. VOL

Adjusts the audio volume.

>>Click here to see an animation clip

8. MUTE

Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode.

9. AUTO

Adjusts the screen display automatically. By changing the resolution in the control panel, auto function is performed.

10. MENU

Opens the on-screen menu and exits from the menu or closes the screen adjustment menu.

11. ENTER

Activates a highlighted menu item.

12. PRE-CH

Returns to the immediately previous channel.

- This fuction does not work for this monitor.

13. CH/PAGE

Selects channels or page.

- This fuction does not work for this monitor.

14. SOURCE

Changes the video source.

15. INFO

The current picture information is displayed in the top left corner of the screen.

16. EXIT

Exits from the menu screen.

17. Up-Down Left-Right buttons

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

18. P.MODE (M/B)

When pressing this button, current picture mode is displayed at the bottom center of the screen.

AV / S-Video / Component : P.MODE The Monitor has four automatic picture settings that are preset at the factory. Then press the button again to circle through available preconfigured modes. ( Dynamic Standard Movie Custom )

PC/DVI/BNC : M/B (MagicBright™) MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. (Entertain Internet Text Custom )

19. STILL

When pressing this button, STILL is displayed at the bottom center of the screen. Press the button once to freeze the screen. Press it again to unfreeze.

20. BBE

Recreates the natural sound and improves sound clarity through boosting high and low range frequencies. As a result high sounds are clearer, brilliant and finely detailed while low sounds are tight, well-defined and harmonically rich.

21. MTS

You can select MTS (Multichannel Television Stereo) mode.

Audio Type MTS/S_Mode Default

Mono Mono

FM Stereo

- This fuction does not work for this monitor.

22. PIP

Every time you press the button, a PIP screen appears.

23. SOURCE

Changes the source of the PIP window signal.

24. SIZE

Switches the Picture Size.

25. SWAP

Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window.

26.

Rewind

27.

Stop

28.

Play/Pause

29.

Fast forward

Stereo

SAP

Mono Stereo

Mono SAP

Manual Change

Mono

Mechanical Layout | Monitor Head | Stand | Speaker | Installation VESA Bracket | Wall Bracket Installation

1. Mechanical Layout

2. Monitor Head

3. Stand

4. Speaker

5. Installation VESA Bracket

When installing VESA, make sure to comply with the international VESA standards.

Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place

an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Monitor.

Samsung is not responsible for any product damage or any injury caused by installation at customer's discretion.

Dimensions

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

6. Wall Bracket Installation

Contact a technician for installing the wall bracket.

Samsung Electronics is not responsible for any damages to the product or harm to customers when the

installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components(Sold separately)

Only use the components and accessories shipped with the product.

Wall-BracketB Set-BracketC

Screw:

8 EA

Screw:

3 EA

Wood Screw:

7 EA

How to assemble the Wall Mount Bracket

1. Mark the location of hole on the wall.

2. Make over 35mm-depth-hole on the marked location using drill.

3. Fix anchors F on each hole on the wall.

4. Connect wall-bracket A to the wall with wood screws E after fitting anchors F into the wall-bracket A.

If the bracket is not firmly fixed to the wall, set can fall off.

1. Turn the power off and unplug the power cord from the outlet.

2. Place the monitor faced down on a soft cloth or cushion on a table.

3. Attach the set-bracket B onto the rear side of the monitor set and secure the screws C.

Anchor:

7 EA

Installation Guide

1. Insert three Hangers of the set-bracket B into the grooves of the wall-bracket A.

2. Fix set-bracket B and wall-bracket A with screws D.

Before installing the set on the wall, connect the cables to the set first.

+ 49 hidden pages