Samsung 172MP, 152MP User Manual

SyncMaster 152MP / 172MP

Main Page

Safety Instructions

Notational

Power

Installation

Cleaning

Other

Introduction

Unpacking

Front

Rear

Remote Control

Setup

Connecting Your Monitor

Connecting to a Computer

Connecting to Other Devices

Installing the Monitor Driver

Automatic

Manual

Installing a VESA Base

Folding or removing the base

Installing a VESA Base

Adjusting Your LCD Monitor

User Controls

User control buttons

Direct-Access Features

On-Screen Display

OSD Functions

Screen Adjustment Animation Clips

Troubleshooting

Check before Calling for Service

Problems and Solutions

Q & A

Specifications

General Specifications

PowerSaver

Preset Timing Modes

Information

Service Center

Terms

Regulatory

Natural Color

For Better Display

Authority

English > Main > Index

Notational

Power Installation Cleaning Other

English > Main > Safety Instructions > Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Notational

Power

Installation Cleaning Other

English > Main > Safety Instructions > Powe r

When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

This may cause a fire.

Notational Power

Installation

Cleaning Other

English > Main > Safety Instructions > Installation

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Put your monitor in a location with low humidity and a minimum of dust.

An electric shock or fire could result inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

The monitor can cause injury by falling.

Set down the monitor carefully.

It could be damaged or broken.

Do not place the monitor face down.

The TFT-LCD surface may be damaged.

Notational Power Installation

Cleaning

Other

English > Main > Safety Instruction s > Cleaning

When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.

Do not spray detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

A dirty connector can cause an electric shock or fire.

Do not set a glass of water, chemicals or any small metal objects on the monitor.

This may cause damage, electric shock or a fire.

If a foreign substance gets into the monitor, disconnect the plug and then

contact a service center.

Notational Power Installation Cleaning

Other

English > Main > Safety Instructions > Ohter

Do not remove cover(or back). No user serviceable parts inside.

z This may cause an electric shock or a fire.

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service.

z This may cause an electric shock or fire.

Do not place any heavy objects on the monitor.

This may cause an electric shock or a fire.

For each hour of looking at the monitor, you should let your eyes rest for 5 minutes.

This will reduce eye fatigue.

Do not use or store inflammable substances near the monitor.

This may cause an explosion or fire.

Do not try to move the monitor by pulling on the wire or the signal cable.

This may cause a breakdown, electric shock or a fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or a fire due to damage to

the cable.

Never insert anything metallic into the monitor openings.

This may cause an electric shock, fire or injury.

Keep all power adaptors apart.

z Possible fire hazard.

Keep power adaptor away from any other heat source.

Possible fire hazard.

Remove and discard vinyl bag from power adaptor before use.

z Possible fire hazard.

Always keep power adaptor in well-ventilated area.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

Change the mode to energy save or set a screensaver to moving picture

when you need to be away from the monitor for an extended period of time.

Unpacking

Front Rear Remote Control

English > Main > Introduction > Unpacking

Please make sure the following items are included with your monitor. If any items are missing, contact

your dealer.

User's Guide and Natural Color/

Driver Installation CD

Quick Setup Guide Signal Cable(15 pin D-Sub)

Monitor

Warranty Card

(Not available in all locations)

Power Cord

DC Adapter

Remote Control

Sold separately

TV Tuner Box

Batteries (AAA X 2) Audio Cable

Unpacking

Front

Rear Remote Control

English > Main > Introduction > Front

For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model.

1. PC mode button 6. Up-Down button / Channel

2. PIP mode button 7. Left-Right button / Volume

3. Video mode button 8. Menu button

4. Audio mode button 9. Exit button

5. Power button / Power indicator

PIP(Picture in Picture)?

Feature allowing one program to be viewed on the entire screen while one or more programs play in small windows superimposed over the base program. PIP is also referred to as Split Windows.

button

10. Auto button

Unpacking Front

Rear

Remote Control

English > Main > Introduction > Rear

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model.

A. PC Connection Terminal

1. Power Connection Terminal (14V DC)

2. Computer Connection Terminal (15 Pin D-SUB)

3. Audio Connection Terminal (Audio (ST))

B. AV Connection Terminal

1. AV right audio / video connection terminal (L,R)

2. S-Video connection terminal

C. Antenna Connection Terminal

(When TV is connected)

D. Headphone connection terminal

Unpacking Front Rear

Remote Control

English > Main > Introduction > Remote Control

For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model.

The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor.

Button Names | Replacing Batteries | Usage

1. Button Names

1. Power button

2. PC mode button

3. PIP(Picture-in-Picture) mode button

4. Video mode button

5. Audio mode button

6. PIP Position button

7. PIP Size button

8. Up-Down button / Channel button

9. Left-Right button / Volume button

10. Menu button

11. Exit button

12. Mute button

13. Channel button

14. Display button

15. Previous channel button

16. Auto button

17. Channel search button

18. MTS/S-mode button

19. Caption button

(Not supported)

2. Replacing Batteries

1. Slide out the cover pressing part marked .

2. Insert the batteries matching their polarities (+, -).

3. Slide in the cover.

Connecting Your Monitor

Installing the Monitor Driver Installing a VESA base

English > Main > Se tup > Connecting Your Monitor > Connecting to a Computer

Connecting to a Computer

Connecting to other devices

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

1. Connecting to a Computer

1. Connect the power cord to the DC adapter and connect the adapter jack to the DC POWER port on the back of your monitor.

2. Connect the signal cable to the video port on your computer.

3. Connect the audio cable for your monitor to the audio port on the back of your computer.

4. Turn on both your computer and the monitor.

5. You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.)

Contact a local Samsung Electronics service center to buy optional items.

Connecting Your Monitor

Installing the Monitor Driver Installing a VESA base

English > Main > Setup > Connecting Your Monitor > Connecting to other devices

Connecting to a Computer

Connecting to other devices

AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor.

Connecting AV Devices | Connecting TV | Connecting to a Macintosh | Connecting Headphone

1. Connecting AV Devices

The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on.

1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the monitor using the RCA or S-VHS cable.

S-VHS or RCA cable is optional.

2. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio cables.

3. Select Video or S-Video that is connected to a DVD, VCR or Camcorders using the Source button on the monitor's front.

4. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

2. Connecting TV (Connect a TV tuner box(option) )

With a TV tuner box(option), you can watch TV simply by hooking up the monitor to an antenna or to your cable box. There is no need to buy a TV card which connects to a PC, or additional hardware or software.

1. Connect the antenna or the cable box to the TV tuner box(option), using the "ANTENNA" terminal on the tuner box.

2. Remove the TV Tuner Box cover from the rear of the monitor.

3. Insert the connected tuner box into the slot and firmly tighten the two screws using a coin to lock the box in place. (Loose screws may cause a blank screen or picture noise)

4. Replace the TV Tuner Box cover.

5. Turn on the monitor.

6. Select TV using Source button among the external signal adjustment buttons.

7. Select a desired TV channel.

As this product is designed for PAL or SECAM signals only, you cannot view TV programs in countries where NTSC signals are used.

3. Connecting to a Macintosh

1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER port on the monitor. (Voltage is automatically adjusted by the power adaptor.)

2. Connect the signal cable to the D-SUB port on the Macintosh computer.

3. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh adapter (optional) referring to the switch configuration table shown on its rear.

4. Turn on the monitor and Macintosh.

Contact a local Samsung Electronics service center to buy optional items.

4. Connecting Headphone

You may connect your headphones to the monitor.

1. Connect your headphones to the Headphone-out port.

Connecting Your

Monitor

Installing the Monitor Driver

Installing a VESA base

English > Main > Setup > Installing the Monitor Driver > Automatic

utomatic

Manual

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung-monitor.com/ (Worldwide)

Windows ME | Windows XP/2000

http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monitor/ (Korea) http://www.samsungmonitor.com.cn/ (China)

1. Windows ME

Refer to " When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up automatically, click

1. Insert CD into the CD-ROM driver.

2. Click "

3. Choose your monitor model in the model list, then click the "OK" button.

4. Click the "

Installing the Monitor Driver and User Manual

monsetup.exe

Windows ME Driver

" button in the "

Install

twice in the CD-ROM drive folder of Windows Explorer.

Warning

" window.

" CD-ROM supplied with the monitor.

5. Monitor driver installation is completed.

2. Windows XP/2000

Refer to " When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up automatically, click

1. Insert CD into the CD-ROM driver.

2. Click "

3. Choose your monitor model in the model list, then click the "OK" button.

Installing the Monitor Driver and User Manual

Windows XP/2000 Driver

monsetup.exe

" CD-ROM supplied with the monitor.

twice in the CD-ROM drive folder of Windows Explorer.

4. Click the "

5. If you can see following Message window, then click the " button.

" button in the "

Install

Warning

" window.

Continue Anyway

" button. Then click "OK"

This monitor driver is under a certified MS logo. This installation will not damage your system. The certified driver will be posted on Samsung Monitor Homepage

http://www.samsung-monitor.com/

6. Monitor driver installation is completed.

Connecting Your

Monitor

Installing the Monitor Driver

Installing a VESA base

English > Main > Setup > Installing the Monitor Driver > Manual

utomatic

Manual

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung-monitor.com/ (Worldwide)

To install the monitor driver manually, follow the procedures explained below after checking your operating system.

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monitor/ (Korea) http://www.samsungmonitor.com.cn/ (China)

1. Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" "

Control Panel

" then click the "

Appearance and Themes

" Icon.

3. Click "

4. Click the "

Display

" icon and choose the "

Properties

" button on the "

Settings

Monitor

" tab then click "

" tab and select "

Advanced..

Driver

" tab.

+ 44 hidden pages

Samsung 172MP, 152MP User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual