Sampo SC-29FA15 Service Manual

Download

Page 1

SAMPO

SERVICE MANUAL

1. Caution……………………………………………………………2

2. Specification………………………………………………………6

3. BOM List…………………………………………………………..9

4. Alignment Procedure………………………………………….… 21

5. Block Diagram……………………………………………………224

6. Schematic Diagram………………………………………………25

7. PCB Layout………….……………………………………………26

8. Exploded View Diagram…………………………………………..27

This manual is the latest at the time of printing, and does not include the mo difi cat io n w hich may be made af ter the pri nti ng, by the constant improvement of product.

SC-29FA15

Page 2

WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION:

Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION

RISK RISK OF OF ELECTRIELECTRICC

SHOCK SHOCK DO DO NOT NOT OPEN.OPEN.

dangerous

Page 3

FOR YOUR PERSONAL SAFETY

1. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.

4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

5. Never push objects of any kind into this television set through cabinet slots as the y may touch dangerous voltage points or short out parts that could result in a fire or electr ic shock. Never spill liquid of any kind on the television set.

6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.

9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury to a child or an adult, and serious damage to the appliance . Use only with a car t or stand recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and should use a mounting kit approved by the manufacturer.

10.2. An appliance and car t combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

CAUTION:

Read all of these instructions. Save these instructions for later use . Follo w all Warnings and Instructions marked on the audio equipment.

1. Read Instructions- All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions- The safety and operating instructions should be retained for future reference.

3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions- All operating and use instructions should be followed.

IMPORTANT SAFETY INSTRUCTIONS

Page 4

PROTECTION AND LOCATION OF YOUR SET

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.

12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.

13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.

14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to protect it from overheating. These openings must not be blocked or covered.

Never cover the slots or openings with cloth or other material. Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. Never place the set near or over a radiator or heat register. Never place the set in enclosure, unless proper ventilation is provided.

PROTECTION AND LOCATION OF YOUR SET

15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some

protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrode, and requirements for the grounding electrode.

15.2. Note to CATV system installer : (Only for the television set with CATV reception)

This reminder is provided to call the CATV system attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power

circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning and power-line surges.

ANTENNA LEAD- IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

ELECTRIC SERVICE

EQUIPMENT

GROUND CLAMP

NEC-NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS

a built-in

installer s

Page 5

OPERATION OF YOUR SET

18.

This television set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.

19. If the television set does not operate normally by following the operating instructions, unplug this television set from the

wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television set to normal operation.

20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on

a holiday, turn the television set and unplug the television set from the wall outlet.

IF THE SET DOES NOT OPERATE PROPERLY

21. If you are unable to restore normal operation by following the detailed procedure in your operating instructions,

do not attempt any further adjustment. Unplug the set and call your dealer or service technician.

22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for

service, unplug the set and have it checked by a professional service technician.

23. It is normal for some TV sets to make occasional snapping or popping sounds, par ticularly when being

turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service technician.

FOR SERVICE AND MODIFICATION

24. Do not use attachments not recommended by the television set manufacturer as they may cause hazards.

25. When replacement parts are required, be sure the service technician has used replacement parts specified

by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

26. Upon completion of any service or repairs to the television set, ask the ser vice technician to perform

routine safety checks to determine that the television is in safe operating condition.

off

Page 6

PFS2 FORMAT-1 Report

Date: 2004-6-10 15:28

ProductView......:

ort by............:

Specs / Products SRF NO./ODF NO.

MasterData Customer Id Version

0.1

Status

WG Archived

Brand EAN

UPC

Rece

tion

+Tunin

- presets/channels

181

+Tunin

- technolo

PLL

+Tunin

- Indication

---

+Fre

Bands

FS TUNER

+Channels

VHF:2-13, UHF:14-69, CATV: 1-13, A-W.W+1--W+84,A-5---A-1,5A

+IF Fre

PICTURE 45.75MHz

+TV Systems Off Air

PAL M/N NTSC M (3.58 -

4.433)

+Add S

stems Ext In

---

+TV S

stems Multi

PAL NTSC

+Sound S

stems

AV STEREO, BTSC

Picture - Processin

+Scan

Standard

+Scan Modes

4:3

+Wide Screen Switchin

+Combfilter

+Picture Control

4 Picture Modes, Brightness, Color, Contrast, Tint, Sharpness Cont Var

+Pict Enhancement

Black Stretch

+Pict Noise Reduction

---

Picture - Dis

play

+Display T

ype

DV - CRT - FSQ

+Screen Format

4:3

+Size

(

Visual)" - size/vis. cm

25"

+Deflection S

stem (CRT onl

+Tube Technology (CRT onl

Black Matrix, Iron

+CRT Defl +CRT Gun

Stand Gun

+CRT Ma

n field

Normal

+Resolution +Coatin

g (

only for D.V. sets

)

+White Point Sound +Leaflet Power +RMS Power Intern +RMS Power Extern +Surround Sound

+Sound Features

Mute, BTSC, Sound effect

+Sound Control

Volume, AVL,

Sound - S

eakers

eaker configuration

2 speakers

eakers used

Normal Range

eaker Size User Interface +Interface Name

29T17

+Voice Control +Menu

Cursor Control

+Menu Colours +Menu Languages

English/French/Spanish /Portuguese

+Special Features

Child Lock, NoteBook, Calendar, Favorite Channel Program preengage Children restriction

erational Features

CCD

+PP Features +Tuning/Install Features

Auto Store, Factory Mode, Language Selection, Service Mode

Product:@

2 Specification

Page 7

Date: 2004-6-10 15:28

ProductView......:

ort by............:

Specs / Products

Product:@

+Clock/Timer Functions

Sleep timer

+Local Controls Front +Local Controls To

+Indicators - screen +Indicators - front +Numb of Loc Cont

(

incl Mains

)

+Number of Ind.

(

incl Mains

)

+Local Controls (Old)

Channel +-, Tact Switch, Vol +-, TV/AV, MENU

Remote Control +Remote Control - sco

+Remote Control - t

Standard

+Remote Control - t

ypenr

+Remote Control - features Connectors Rea

+Scart RGB+Y/C+CVBS +Scart RGB+CVBS +Scart CVBS+Y/C +Com

onent In (Y/U/V) Cinch

+In Y/C+Cinch

(

CVBS+St

)

+In Y/C+Cinch(CVBS+Mo

)

+In Y/C+Cinch(St

)

+In BNC (CVBS

)

+In Cinch(CVBS+St

)

+In Cinch

(

CVBS+Mo

)

---

+Out Cinch

(

CVBS+St

)

+Out Cinch

(

CVBS+Mo

)

+Out Cinch Audio Stereo +Out Cinch Audio Mono +Out Cinch Dolb

Surround

+Di

Audio Out

+Louds

eakers +Control Busses +Feature Slot +ITV Smart Port +Terr. Antenna in

75 Ohms (F type)

Guide + IR Blaster Jack Connectors Fron

+In Cinch (CVBS + St

)

+In Cinch (CVBS+Mo

)

+Headphone Out Connectors Side +In Y/C + Cinch

(

CVBS+St

)

+In Y/C + Cinch Stereo +In Cinch

(

CVBS + St

)

+IN Cinch (CVBS + Mo

)

+Headphone Out Connectors To

Connectors Mechanical St

lin

+Cabinet Name

29T17

+Confi

uration

Symm

+Gra

hics/Logo's

TCL

+Cabinet Colour and Finish +Mechanics +S

eaker Visibilit

Standard

General +Se

ment

Standard 4:3

+Chassis

M134

+Software Deliver

Mode +Software Version +Mains Volta

110-240V

+Mains Fre

uenc

50/60Hz

e Mains Cord

Power Consum

tion (P)TV in On

Power Consum

tion SB in Watts

Less than 6W

Power Consum

tion Semi SB in W +Power in "ON" for +Power in Standb

for +Power in "OFF" for Wei

ht (P)TV (incl. Packagin

Weight (P)TV (excl. Package

)

Page 8

Date: 2004-6-10 15:28

ProductView......:

ort by............:

Specs / Products

Product:@

Weight AVUnit excl Packagin

+INDICATION on BACKCOVE

+Channel Final E

quip

ment

+Packa

ging

- methods +Documents and manuals +Lan

guag

es DFU

+Cables Su

lied

+Antenna Su

lied

+Stand Su

lied

+Aux E

quip

m Supplied

Batteries for RC (2 x AA)

Packa

ging

- width cm

Packa

ging

- height cm

Packa

ging

- depth cm Miscellaneous +EAN Indication +A

robation +Tests +Local Inte

ration Various Perf. Param. +Service Call-Rate PIP/POP +T

ype

+Features Di

ital Reception +Transmission Built-in Data S

stem +Text Standard +

(

Tele)text Features

+Nbr bck

rnd page / Mem Size

+Text Technolo

+Digital Data handlin

+Program Guide Built-in Clock/Timer +T

ype

+Features Built-in Radio +T

ype

Built-in PC displa

+PC Synch +PC Control Built-in DVD drive +T

e of Medium

e of Dec

Phased Out Items +Tuner/Frontend +Sensitivit

+CRT EHT +Li

htning Protection

+Accoun

+XX(Radio Antenna in

)

+Non Volatile Memor

+In Y/C + Cinch(CVBS+Mo

)

Version of deck

2004-6-10 15:28 2927 PFS 3 of 3

Page 9

3 BOM List

PART NO. SEPC

SINGLE QTY

LOCATION UNIT

11-0BC337-0BX TRANSISTOR (NPN) BC337-40 1 Q1501 PC 13-00AS12-13B IC AS1213B 1 IC1501 PC 14-IRE05B-XX0 IR EMITTING DIODE TSAL6200 1 D1501 PC 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R1502 PC 18-CB0229-JNX RES. C.F. 2.2 OHM 1/6W +/-5% 1 R1501 PC 25-HBB479-M1X CAP. ELEC 4.7 UF 10V +/-20% 1 C1504 PC 26-EBP101-JCS CAP. CER 100 PF 50V +/-5% 2 C1502;C1501 PC 26-EBP104-ZFS CAP. CER 0.1UF 50V +80%/-20% 1 C1503 PC 40-UOCASR-RMB1XG P.C.B. REMOTE HANDSET BD 1 PC 41-WJ0120-B00 WIRE BARE JUMPER 12MM 1 J1501 PC 45-COS455-KY1 CERAMIC RESONATOR 455KHZ 1 X1501 PC 49-HS36R1-00X1A RUBBER PAD KEYS 1 PC 55-HS36RB-1HA9A LOWER CASE - REMOTE HANDSET 1 PC 55-HS36RD-0HA9A BATT. DOOR - REMOTE HANDSET 1 PC 55-HS36RT-1HA7G TOP CASE 1 PC 58-HS36R2-2UI9H INLAY REMOTE HANDSET 1 PC 67-X38064-0E2 BATTERY SPRING (+/-) 1 PC 67-X38065-0E2 BATTERY SPRING (+) 1 PC 67-X38066-0E2 BATTERY SPRING (-) 1 PC 74-007026-60C POLYBAG (70MMX260MMX0.06MM) 1 PC T8-HS36R1-M134 ASS'Y-REMOTEHANDSET(R) 1 EA V8-T7M134-03E04 SOFTWARE CODE 1 FOR IC001 PC 74-015020-50Q PLASTIC BAG 1 FOR CRT BD PACKING PC 74-060060-40F POLYBAG ANTISTATIC (MAIN PCB) 1 PC 75-326030-C00 SKD POLYFOAM 1.25 PC 76-002509-0AC CARTON BOX 0.084 PC 74-120120-8CD POLYBAG (120CMX120CM) 1 FOR FRONT CABINET PC 74-145120-8CD POLYBAG (145CMX120CM) 1 FOR REAR CABINET PC 74-339020-50C EPE BOARD (800MMX600MMX5MM) 0.25 FOR R.CAB PC 74-344780-50C EPE BOARD (900MMX400MMX5MM) 0.75 FOR REAR CABINET PC 76-001497-0AF CARTON BOX LWH 640X460X360MM 0.028 FOR OTHER PC 76-00BT18-0AF CARTON BOX 0.25 FOR FRONT CABINET PC 76-00BT18-0AR CARTON BOX 0.25 FOR REAR CABINET PC 76-346740-01A CARTON SHEET LWH 440X620X3MM 0.024 FOR OTHER PC 77-120120-6WC BUBBLE BAG (120CMX120CM) 0.5 FOR FRONT CABINET PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 ‘+’TO Q918‘C’、‘-’ PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 R1011，‘+’TO IC1001 PI PC 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q1003 PC 13-MSP342-5GB IC MSP 3425G 1 IC1001 PC 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 2 R1001;R1002 PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 2 R1023;R1022 PC 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5

1 R1004 PC

18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5

1 R1007 PC

18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5

1 R1005 PC

Page 10

18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% 1 R1006 PC 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 5 C1016;C1015;C1014;C1013;PC 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C1019 PC 25-BFB339-M1X CAP. ELEC 3.3 UF 50V +/-20% 1 C1010 PC 26-ABC339-CZX CAP. CER 3.3 PF 50V +/-0.25

2 C1001;C1002 PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 4 C1031;C1034;C1038;C1037 PC 26-EBP152-KBS CAP. CER 1500PF 50V +/-10% 1 C1012 PC 26-EBP220-JCS CAP. CER 22 PF 50V +/-5% 2 C1036;C1035 PC 26-EBP471-JCS CAP. CER 470 PF 50V +/-5% 1 C1025 PC 26-EBP560-JZX CAP. CER 56PF 50V +/-5% SL T

2 C1004;C1005 PC 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 6 C1024;C1023;C1018;C1011; PC 27-MBC474-J0X CAP. M.P.E 0.47UF 63V +/-5% 1 C1017 PC 34-A220K0-1IX COIL PL - 22UH +/-10% LGA030

2 J1005;L1001 PC 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 1 J1008 PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J1009 PC 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J1010 PC 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J1006 PC 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 1 J1007 PC 41-WJ0145-B00 WIRE BARE JUMPER 14.5MM 1 J1002 PC 41-WJ0150-B00 WIRE BARE JUMPER 15MM 1 J1001 PC 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM 1 J1004 PC 45-OSC18M-4Y0 CRYSTAL 18.432M 1 X1001 PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 3 L501 FOR (+) TO P503(1); PC 11-A562TM-0BX TRANSISTOR 2SA562TM-0 1 Q507 PC 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 3 Q502;Q504;Q506 PC 11-SC4544-0AX TRANSISTOR 2SC4544 3 Q501;Q503;Q505 PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R515 PC 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5

1 R514 PC 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 3 R503;R508;R513 PC 18-CB0561-JNX RES. C.F. 560 OHM 1/6W +/-5% 3 R510;R505;R501 PC 18-CB0681-JNX RES. C.F. 680 OHM 1/6W +/-5% 5 R502;R506;R509;R522;R511 PC 18-FE0272-JNX RES. M.O. 2.7K OHM 1/2W +/-5

3 R519;R520;R521 PC 18-FG0153-JHX RES. M.O. 15K OHM 2W +/-5% 3 R517;R518;R516 PC 25-BCB471-M1X CAP. ELEC 470 UF 16V +/-20% 1 C506 PC 25-BLA100-M1X CAP. ELEC 10 UF 250V +/-20% 1 C504 PC 26-EBP103-ZF1 CAP CER 50V 2.5MM 10nF -20%+

1 C508 PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 1 C509 PC 26-EBP391-JCS CAP. CER 390PF 50V +/-5% 1 C501 PC 26-EBP471-JCS CAP. CER 470 PF 50V +/-5% 2 C502;C503 PC 35-139730-00X FERR. BEAD BF60 2 FOR C508 (L505 & L506) PC 40-2980UA-CRB1XG P.C.B. CRT BD 1 PC 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 L504 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 3 R504;R507;R512 PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J503 PC 46-10967W-01XG PIN BASE *1 TJC1-1A 1 P501 FOR CRT GROUNDING

PC 46-33079W-04XG PIN BASE *4 TJC3-4A 1 P502(反插)FOR M.BD P421 PC 46-33079W-05XG PIN BASE *5 TJC3-5A 1 P503 FOR M.BD P201 PC

Page 11

26-AMM152-KRX CAP. CER 1500 PF 2KV +/-10%

1 C505 PC 34-R100K2-1BX COIL CHOKE 10 UH +/-10% 1 L503 PC 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 L502 PC 47-CRT004-XX0G CRT SOCKET GZS10-2-108 1 S501 PC 46-26514H-04XG HS 4P A/B 500/13 RBGW TJC1-

1 P411H FOR D.Y COIL PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D410 PC 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/

1 R416 PC 18-CB0682-JNX RES. C.F. 6.8K OHM 1/6W +/-5

1 R432 PC 18-CE0103-JNX RES. C.F. 10K OHM 1/2W +/-5% 1 R316 PC 18-EG0229-JHX RES. FUS. 2.2 OHM 2W +/-5% 1 R461 PC 18-FF0181-JGX RES. M.O. 180 OHM 1W +/-5% 1 R309 PC 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C245 PC 25-BCB220-M1X CAP. ELEC 22 UF 16V +/-20% 1 C304 PC 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C210 PC 27-AHR564-JSX CAP.M.PP 400V 560NF +/-5% 1 C419 PC 27-ALQ432-J0X CAP. M.PP 0.0043UF 1.6KV +/-

1 C411 PC 27-ALQ722-J0X CAP. M.PP 7200 PF 1.6KV +/-5

2 C412;C414 PC 27-MBC222-J0X CAP. M.P.E 0.0022UF 63V +/-5

1 C311 PC 27-MBC224-J0X CAP. M.P.E 0.22UF 63V +/-5% 1 C309 PC 27-RHQ223-J0X CAP. PP 0.022 UF 400V +/-5% 1 C413 PC 36-LIN180-XX1 COIL LINEARITY 18 UH 1 L414 PC 36-WID601-XX1 COIL CHOKE 600 UH 1 L413 PC 37-SC2701-68V01 FBT BSC27-0168V 1 T402 PC 75-388320-CC0 POLYFOAM BOARD 0.05 FOR PMC PC 89-242080-JZ0 TRANSPARENT PACKING (6CMX41M) 1.3 FOR PMC M 07-457FF5-NX7G ALPS FS TUNER TEDH9-249A 1 TU101 PC 11-SD2638-0AX TRANSISTOR 2SD2638 1 Q411 PC 13-T7M134-03M01 CPU TMPA8859CSNG 1 IC101 PC 13-TDA894-4JS IC TDA8944J 1 IC602 PC 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 2 R036A;R001 PC 18-CB0153-JNX RES. C.F. 15K OHM 1/6W +/-5% 1 R413 PC 18-CB0183-JNX RES. C.F. 18K OHM 1/6W +/-5% 2 R612;R615 PC 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/

1 C212 PC 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% 1 R414 PC 18-CB0562-JNX RES. C.F. 5.6K OHM 1/6W +/-5

1 R315 PC 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% 1 R901 PC 18-EG0109-JHX RES. FUS. 1 OHM 2W +/-5% 2 R433;R431 PC 18-RF0688-JGX RES. WIRE ROUND 0.68 OHM 1W

1 R304 PC 18-RG0159-JHX RES. WIRE ROUND 1.5 OHM 2W +

1 R313 PC 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C235 PC 25-BKJ681-M1X CAP. ELEC 680UF 200V +/-20%

(

1 C806 PC 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C306 PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 1 C902 PC 27-PBC102-J0X CAP. P.E 0.001UF 63V +/-5% 2 C640;C637 PC 27-PBC154-J0X CAP. P.E. 0.15 UF 63V +/-5% 2 C639;C636 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 2 R242;J310 PC 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 4 JP902;R243;R914;R915 PC

Page 12

41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 2 JP901;J405 PC 41-WJ0100-B00 WIRE BARE JUMPER 10MM 2 J803;J804 PC 45-FIL4M5-0Y3 CER.FILTER LT4.5MH 1 X202 PC 45-SAWF18-590 SAW FILTER F1859 1 Z101 PC 46-12866W-02XG PIN BASE *2 S11-02Y 1 P601 FOR FRONT CAB.(SPK) PC 46-28559W-02XG PIN BASE *2 TJC1-2A 1 P801 PC 46-33079W-02XG PIN BASE *2 TJC3-2A 1 P602 FOR FRONT CAB.(SPK) PC 46-33079W-05XG PIN BASE *5 TJC3-5A 1 P001 FOR IR BD P005 PC 46-33079W-07XG PIN BASE *7 TJC3-7A 1 P911(反插) FOR SIDE AV BPC 47-RCA023-XX1G RCA JACK 3 PV YEL WHI RED/SW 2 P905;P903 PC 50-03150D-1GS1G FUSE 3.15AT 250VAC 5MMX20MM 1 F801 PC 62-B159MB-5UN MAIN BD BRACKET 1 PC 63-W30100-AB4G S/T SCREW W 3 X 10 AB 8 MTG M.BD & M.BD BKT PC 70-271510-00A SERVICE CARD 1 FOR PRODUCTION USE PC 71-270870-0A9 LABEL 2 PC 90-0DSTG1-SR1U HEAT SINK DSTG-1 1.3 FOR Q411,Q414,IC602,IC30G 90-269080-ZU0U CLEAN COATING TC-131L 14KG/B

0.1 G 49-382380-BAT BATTERY 7# (R03P AAA SUM-4) 2 PC 71-EBI700-003A4 LABEL SERIAL NO. 4 尺寸：20x3mm 内容：6030PC 71-TWSAMP-BAT9A LABEL 1 贴在2节电池薄膜上面 PC 72-BT17A6-C039A OPERATION MANUAL 1 PC 74-010050-40C POLYBAG FOR POWER (10CMX50CM) 1 PC 74-022032-6WEAD PLASTIC BAG 1 PC 74-130130-80HAA POLYBAG W/SUFFOCATION WARNIN

1PC 75-444370-EC0 POLYFOAM 1 PC 75-444380-EC0 POLYFOAM 1 PC 75-444390-EC0 POLYFOAM 1 PC 75-444400-EC0 POLYFOAM 1 PC 75-444410-EC0 POLYFOAM 1 PC 75-444420-EC0 POLYFOAM 1 PC 75-444430-EC0 POLYFOAM 1 PC 76-444510-0AT9M CARTON BOX 1 PC 02-GND029-XX0G ASS"Y-CRT GND WIRE & HOUS.(2

1PC 36-DEG290-AX2 DEGAUSSINGCOIL3100mm 1 PC 42-61308F-XX2G SPEAKER 8 OHM 8W 2 SP602;SP601 PC 46-14026H-02XG HS 2P 2468#22 570MM S11-2Y/7

1 P601H FOR M. BD P601 PC 46-27580H-02XG HS 2P22 600/7 F/W TJC3-2Y 1 P602H FOR M. BD P602 PC 54-113970-0U0 PVC TUBE AWG NO.5 0.32 FOR SPK HOUSING M 54-114000-00X FELT TAPE (150MMX19MMX0.3MM) 9 PC 54-205140-000 SPACER CRT MOUNTING T=2MM 4 MTG CRT & FRONT CAB. PC 54-314740-0X0 CRT FIBRE SHEET (22MMX22MMX0. 8 PC 57-10654X-00F TWIST TIE NY66 13 PC 57-FGP005-XX1 LED LENS 1 PC 59-130460-00X RUBBER PAD (25MMX7MM) 2 STICK ON F.CAB. (FOOTINGPC 59-312160-000 SPEAKER RUBBER CUSHION 8 FOR SPK PC 63-B30060-BT4G S/T SCREW B 3 X 6 BT 2 MTG SIDE AV BD PC 63-B30080-AB4G S/T SCREW B 3 X 8 AB 5 MTG KEY BD & F. CAB.;MT

Page 13

63-B40150-AB4G S/T SCREW B 4 X 15 AB 12 MTG CRT SUPPORTER & F. CPC 63-W30100-AB4G S/T SCREW W 3 X 10 AB 2 MTG PUSH BUTTON & FRONT PC 63-W30100-AB4G S/T SCREW W 3 X 10 AB 2 MTG LIGHT LENS & FRONT CPC 63-W30100-AB4G S/T SCREW W 3 X 10 AB 1 MTG LENS & FRONT CAB. PC 63-W30140-HS4G S/T SCREW W 3 X 14 HS 8 MTG SPK PC 63-Z30100-AB4G S/T SCREW 3.0 X 10 2 MTG PWR SW. BD PC 65-A60200-20EG TV RAW PAD PAPER 20MM 6MM X

4 MTG CRT & FRONT CAB. PC 65-Z60100-50EG NUT M 6.0 X 1.0 4 MTG CRT PC 67-313820-2E0 CRT BRACKET 4 PC 67-X21679-0E0 SPRING CRT 6MMX50MMX0.6MM 2 PC 67-X41381-0E2 POWER KNOB SPRING 1 PC 55-BT17FC-0CN9K FRONT CABINET 1 PC 56-407310-0HA5O DECORATE ANNULUS 1 PC 56-BT18FB-1HA5G PUSH BUTTON 1 PC 56-BT18PK-0HA5G POWER KNOB 1 PC 56-C276LS-1HC5Z LENS 1 PC 58-CA61SI-1UI9J INLAY SIDE AV 1 PC 67-L42700-0A09A LOGO 1 PC 02-IRR001-XX1 IR RECEIVER MODULE HRM380017 1 IR001 PC 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q003 PC 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q002 PC 18-CB0181-JNX RES. C.F. 180 OHM 1/6W +/-5% 1 R090 PC 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R091 PC 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% 1 R089 PC 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C081 PC 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C080 PC 40-BT18S6-IRA1XG IR RECEIVE BD 1 PC 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 J001 PC 46-33079W-02XG PIN BASE *2 TJC3-2A 1 P005A PC 46-37170H-02XG HS 2P 2468#24 260 TJC3-2Y/JC

1 P005B FOR PWR SW. BD S80PC 46-39131H-05XG HS 5P 2468#24 600 TJC3-5Y/JC

1 P005 FOR M.BD P001 PC 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5

1 R086 PC 18-CB0182-JNX RES. C.F. 1.8K OHM 1/6W +/-5

1 R085 PC 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5

1 R084 PC 18-CB0432-JNX RES. C.F. 4.3K OHM 1/6W +/-5

1 R083 PC 18-CB0622-JNX RES. C.F. 6.2K OHM 1/6W +/-5

1 R082 PC 40-29T18E-KEC1XG P.C.B. KEY BD 1 PC 41-WJ0070-B00 WIRE BARE JUMPER 7MM 1 J082 PC 46-37170H-02XG HS 2P 2468#24 260 TJC3-2Y/JC

1 P001 FOR IR BD P005A PC 48-TAC001-XX0 TACT SWITCH 6 S005;S004;S006;S003;S002PC 54-114000-00X FELT TAPE (150MMX19MMX0.3MM) 9 STICK ON R.CAB PC 55-BA41RC-0CN5F REAR CABINET 1 PC 58-BT18MP-0UI8E PLATE MODEL NO. 1 PC 58-CA41RI-6UI9C INLAY REAR AV 1 PC 62-389620-0UD POWER LINE BLOCK 1 PC 63-B40250-AB2G S/T SCREW B 4 X 25 AB 10 MTG FRONT & REAR CABINE

63-F30100-BT3G S/T SCREW F 3 X 10 BT 2 MTG RCA JACK & REAR CABI PC

Page 14

40-21T18H-SIC1XG P.C.B SIDE AV BD 1 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J002 PC 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J001 PC 46-38610H-07XG HS 7P 1185#26 600MM 1 P002 FOR M.BD P911 PC 47-RCA041-XX0G JACK RCA 3PH H=8MM YL WH RD/

1 P1101 PC 47-SVI002-XX0 Y/C SOCKET VERTICAL TYPE 1 P961 PC 40-21T18H-SWC1XG P.C.B SWITCH BD 1 PC 46-33079W-02XG PIN BASE *2 TJC3-2A 1 S803 FOR IR BD P005B PC 46-33079W-04XG PIN BASE *4 TJC3-4A 1 S804 FOR LAMP PC 46-35063W-03XG PIN BASE *3 VH-3A 2 P804A;P804 FOR POWER CORPC 46-39073H-03XG HS 2P 1617#22 200 TJC1-2Y/VH

1 FOR PWR SW.BD(P804A) & PPC 48-POW001-AX0G SWITCH POWER 1 SW801 PC 51-DC0220-0DN08G POWER CORD 062828/8 1 PC 62-262660-0HN POWER SW.ADAPTER 1 PC 66-382330-0B7 RIVET 2.0X3.7X3.5 4 FOR P804, P804A PC 76-002091-0AT CARTON BOX LWH 624X384X556MM 0.006 PC 76-326350-01A CARTON SHEET 61X37X0.3CM 0.062 PC 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 5 D431;D441;D421;D412;D432PC 10-1N4001-EBX DIODE 1N4001 (RECTIFIER) 1 D301 PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 8 D601;D206;D310;D215;D205PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 7 D602;D603;D604;R212;D211 PC 10-79C3V9-DBX DIODE ZENER 3V9 1/2W 5% 1 D213 PC 10-79C6V2-DBX DIODE ZENER 6V2 1/2W 5% 1 D207 PC 10-79C8V2-DBX DIODE ZENER 8V2 1/2W 5% 1 D303 PC 10-GBY228-F0X DIODE GBY228 1 D411 PC 10-HS5V1B-DBX DIODE 500MW 5.1HSB 1 D001 PC 11-2SA817-AAX TRANSISTOR 2SA817AY 1 Q208 PC 11-630MFP-0AX TRANSISTOR IRF630MFP 1 Q414 PC 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 3 Q919;Q918;Q209 PC 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 7 Q008;Q412;Q413;Q601;Q912PC 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 8 Q914;Q901;Q203;Q204;Q402PC 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 5 Q007;Q917;Q902;Q903;Q904PC 11-SC2482-0BX TRANSISTOR 2SC2482 1 Q401 PC 11-SC3779-DBX TRANSISTOR 2SC3779D (RF AMPL) 1 Q101 PC 13-000040-52P IC 4052 1 IC901 PC 13-00M24C-08P IC EEPROM 8K M24C08 (WRITE) 1 IC001 PC 13-STV817-2AS IC STV8172A 1 IC301 PC 18-CB0100-JNX RES. C.F. 10 OHM 1/6W +/-5% 1 R244 PC 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 7 R245;R920;R937;R234;R101 PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 4 R929;R926;R917;R924 PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 7 R916;R601;R936;R934A;R93PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 8 R925;R003;R004;R031;R032PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 8 R912;R906;R904;R453;R911 PC 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 8 R006;R025;R026;R034;R043PC 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 6 R944;R619;R618;R314;R31

18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5

3 R222;R223;R947 PC 18-CB0121-JNX RES. C.F. 120 OHM 1/6W +/-5% 3 R235;R931;R258 PC

Page 15

18-CB0122-JNX RES. C.F. 1.2K OHM 1/6W +/-5

2 R262;R420A PC 18-CB0123-JNX RES. C.F. 12K OHM 1/6W +/-5% 1 R938 PC 18-CB0151-JNX RES. C.F. 150 OHM 1/6W +/-5% 2 R108;R102 PC 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5

1 R302A PC 18-CB0153-JNX RES. C.F. 15K OHM 1/6W +/-5% 1 R933 PC 18-CB0154-JNX RES. C.F. 150K OHM 1/6W +/-5

1 R254 PC 18-CB0201-JNX RES. C.F. 200 OHM 1/6W +/-5% 1 R235A PC 18-CB0220-JNX RES. C.F. 22 OHM 1/6W +/-5% 1 R104 PC 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 2 R930;R401 PC 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5

5 R616;R417;R044;R942;R946PC 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 2 R952;R953 PC 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 8 R954;R005;R951;R617;R903PC 18-CB0224-JNX RES. C.F. 220K OHM 1/6W +/-5

1 R220 PC 18-CB0271-JNX RES. C.F. 270 OHM 1/6W +/-5% 5 R227;R241;R216;R215;R214PC 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5

1 R412 PC 18-CB0303-JNX RES. C.F. 30K OHM 1/6W +/-5% 1 R219 PC 18-CB0330-JNX RES. C.F. 33 OHM 1/6W +/-5% 1 R923 PC 18-CB0331-JNX RES. C.F. 330 OHM 1/6W +/-5% 3 R247;R233;R225 PC 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5

1 R233A PC 18-CB0333-JNX RES. C.F. 33K OHM 1/6W +/-5% 4 R231;R614;R613;R230 PC 18-CB0392-JNX RES. C.F. 3.9K OHM 1/6W +/-5

2 R008;R007 PC 18-CB0394-JNX RES. C.F. 390K OHM 1/6W +/-5

1 R939 PC 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% 1 R024 PC 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 3 R238;R103;R036 PC 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/

3 R211;R010;R257 PC 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% 1 R229 PC 18-CB0560-JNX RES. C.F. 56 OHM 1/6W +/-5% 1 R107 PC 18-CB0561-JNX RES. C.F. 560 OHM 1/6W +/-5% 1 R946 PC 18-CB0562-JNX RES. C.F. 5.6K OHM 1/6W +/-5

2 R418;R256 PC 18-CB0681-JNX RES. C.F. 680 OHM 1/6W +/-5% 2 R940;R106 PC 18-CB0683-JNX RES. C.F. 68K OHM 1/6W +/-5% 1 R941 PC 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% 2 R902;R908 PC 18-CB0822-JNX RES. C.F. 8.2K OHM 1/6W +/-5

2 R246;R420 PC 18-CB0829-JNX RES. C.F. 8.2 OHM 1/6W +/-5% 2 R621;R610 PC 18-CD0479-JNX RES. C.F. 4.7 OHM 1/4W +/-5% 1 R030 PC 18-DB0222-FNX RES. M.F 2.2K OHM 1/6W +/-1% 1 R302 PC 18-DB0363-FNX RES.M.F 36K OHM 1/6W +/-1% 1 R303 PC 18-DD0103-FNX RES. M.F. 10K OHM 1/4W +/-1% 1 R311 PC 18-DD0183-FNX RES. M.F. 18K OHM 1/4W +/-1% 1 R312 PC 18-FF0242-JGX RES. M.O. 2.4K OHM 1W +/-5% 1 R402 PC 18-FF0681-JGX RES. M.O. 680 OHM 1W +/-5% 1 R419 PC 18-FG0103-JHX RES. M.O. 10K OHM 2W +/-5% 1 R421 PC 18-FG0399-JHX RES. M.O. 3.9 OHM 2W +/-5% 1 R415 PC 18-GM0472-JTX1 RES. 4.7K OHM 7W +/-5% 1 R404 PC 18-RG0109-JHX RES. WIRE ROUND 1 OHM 2W +/-

1 R422 PC 18-RG0228-JHX RES. WIRE ROUND 0.22 OHM 2W

1 R611 PC 25-264610-M1X CAP. ELEC 4.7UF 50V +/-20% N

1 C415 PC

Page 16

25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 8 C620;C619;C228;C041;C033PC 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 8 C904;C905;C909;C910;C924PC 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 5 C930;C914;C912;C233;C219PC 25-BCB220-M1X CAP. ELEC 22 UF 16V +/-20% 1 C645 PC 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 2 C646;C926 PC 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 5 C644;C908;C903;C229;C213PC 25-BDA102-M1X CAP. ELEC 1000 UF 25V +/-20% 1 C632 PC 25-BDA222-M1S CAP. ELEC 25V/2200UF/+/-20% 2 C435;C432 PC 25-BDB100-M1X CAP. ELEC 10 UF 25V +/-20% 1 C641 PC 25-BEA221-M1X CAP. ELEC 220 UF 35V +/-20% 2 C308;C301 PC 25-BEB101-M1X CAP. ELEC 100 UF 35V +/-20% 1 C302 PC 25-BFB100-M1X CAP. ELEC 10 UF 50V +/-20% 1 C237 PC 25-BFB101-M1X CAP. ELEC 100 UF 50V +/-20% 2 C224;C105 PC 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 4 C218;C243;C221;C241 PC 25-BFB470-M1X CAP. ELEC 47 UF 50V +/-20% 1 C250 PC 25-BFB478-M1X CAP. ELEC 0.47 UF 50V +/-20% 2 C227;C923 PC 25-BFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% 3 C223;C251;C101 PC 25-BJB479-M1X CAP. ELEC 4.7 UF 160V +/-20% 1 C401 PC 25-GLA100-M1X CAP. ELEC 10 UF 250V +/-20% 1 C421 PC 25-GLA220-M1X CAP. ELEC 22UF 250V +/-20% 1 C442 PC 25-MFB109-K1X CAP.ELEC 1UF 50V +/-10% 1 C248 PC 25-MFB228-K1X CAP.ELEC 0.22UF 50V +/-10% 1 C216 PC 25-MFB478-K1X CAP.ELEC 50V 0.47UF +/-10% 1 C246 PC 26-AIC221-KBX CAP. CER 220 PF 500V +/-10%

2 C433;C441 PC 26-AIC332-KBX CAP. CER 3300 PF 500V +/-10% 1 C402 PC 26-AIC391-KBX CAP. CER 390 PF 500V +/-10%

1 C403 PC 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 4 C916;C915;C226;C109 PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 8 C418;C633;C643;C911;C043PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 8 C107;C281;C280;C929;C913PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 7 C220;C214;C108;C029;C034PC 26-EBP104-ZFS CAP. CER 0.1UF 50V +80%/-20% 1 C230 PC 26-EBP152-KBS CAP. CER 1500PF 50V +/-10% 1 C002 PC 26-EBP181-JCS CAP. CER 180 PF 50V +/-5% 1 C922 PC 26-EBP221-JCS CAP. CER 220 PF 50V +/-5% 2 C030;C431 PC 26-EBP222-KBS CAP. CER 2.2 NF 50V +/-10% 2 C217;C231 PC 26-EBP270-JCS CAP. CER 27 PF 50V +/-5% 1 C008 PC 26-EBP272-KBS CAP. CER 2700PF 50V +/-10% 1 C003 PC 26-EBP330-JCS CAP. CER 33PF 50V +/-5% 1 C925 PC 26-EBP390-JCS CAP. CER 39PF 50V +/-5% 2 C032;C031 PC 26-EBP470-JCS CAP. CER 47 PF 50V +/-5% 2 C253;C254 PC 26-EBP471-JCS CAP. CER 470 PF 50V +/-5% 1 C239 PC 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 6 C631;C634;C642;C238;C242PC 27-MBC684-J0X CAP. M.P.E 0.68UF 63V +/-5% 1 C305 PC 27-PBC102-J0X CAP. P.E 0.001UF 63V +/-5% 2 C638;C635 PC 27-PBC822-J0X CAP. P.E 0.0082UF 63V +/-5% 1 C247 PC 27-RHQ563-J0X CAP. PP 0.056 UF 400V +/-5% 1 C451 PC 34-A109K0-1IX COIL CHOKE 1 UH +/-10% 1 L102 PC

Page 17

34-R100J2-0EX COIL PL - 10 UH +/-5% 2 L212;L002 PC 34-R101K2-1BX COIL CHOKE 100 UH +/-10% 1 J622 PC 34-R220J2-0EX COIL PL - 22 UH +/-5% 5 L206;L205;L950;L208;L204PC 34-R470J2-0EX COIL PL - 47 UH +/-5% 1 L101 PC 34-R829J2-0EX COIL PL - 8.2 UH +/-5% 1 L209 PC 36-HDR001-AX1 TRANSFOR HOR. DRIVE (MAGNETI

1 T401 PC 40-2918T6-MAH1XG P.C.B MAIN BD 1 PC 41-DE0280-1BB WIRE 1 FOR S1 TO S1 PC 41-WJ0050-B00 WIRE BARE JUMPER 5MM 4 L301;L201;J220A;J026 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J104 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 8 J220;J921;J222;J301;J306PC 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 8 J903;J935;J946;R027;R028PC 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 7 J603;J221;J204;J103;J039PC 41-WJ0070-B00 WIRE BARE JUMPER 7MM 2 J904;J205 PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 8 J229;J307;J609;J610;J612PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 6 J312;D311;J027;J031;J033PC 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 5 J303;J032;J304;J917;J623PC 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J203 PC 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 8 J945;J936;J924;J907;J905PC 41-WJ0090-B00 WIRE BARE JUMPER 9MM 1 J309 PC 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM 3 J105;J614;J106 PC 41-WJ0100-B00 WIRE BARE JUMPER 10MM 8 J906;J916;J934;J933;J932PC 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J001 PC 41-WJ0105-B00 WIRE BARE JUMPER 10.5MM 4 J608;J607;J018;J214A PC 41-WJ0110-B00 WIRE BARE JUMPER 11MM 7 J024;J028;J228;J613;J042PC 41-WJ0115-B00 WIRE BARE JUMPER 11.5MM 3 J912;J939;J034 PC 41-WJ0120-B00 WIRE BARE JUMPER 12MM 1 J023 PC 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 8 J213;J231;J212;J109;J004PC 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 4 J618;J601;R308;J929 PC 41-WJ0130-B00 WIRE BARE JUMPER 13MM 6 J005;J615;J616;J920;J931 PC 41-WJ0135-B00 WIRE BARE JUMPER 13.5MM 3 J030;J909;J910 PC 41-WJ0140-B00 WIRE BARE JUMPER 14MM 2 J226;J302 PC 41-WJ0150-B00 WIRE BARE JUMPER 15MM 8 J020;J224;J613A;J619;J62PC 41-WJ0150-B00 WIRE BARE JUMPER 15MM 2 L411;L412 PC 41-WJ0160-B00 WIRE BARE JUMPER 16MM 2 J214;J208 PC 41-WJ0165-B00 WIRE BARE JUMPER 16.5MM 3 J009;J029;J225 PC 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM 1 J915 PC 41-WJ0185-B00 WIRE BARE JUMPER 18.5MM 1 J606 PC 41-WJ0190-B00 WIRE BARE JUMPER 19MM 5 J218;J219;J926;J914;J913PC 41-WJ0200-B00 WIRE BARE JUMPER 20MM 8 J604;J230;J013;J012;J014PC 41-WJ0200-B00 WIRE BARE JUMPER 20MM 3 J217;J010;J011 PC 45-OSC8M0-0Y0 CRYSTAL 8.0MHZ 1 X001 PC 45-TRA4M5-0Y0 CER TRAP TPS 4.5MHZ 1 X201 PC 46-20598W-04XG PIN BASE *4 TJC1-4A 1 P411 FOR D.Y CONNECTOR PC 46-30615H-04XG HS 4P24 460 F/W TJC3-4Y/SCN-

1 P421 FOR CRT BD P502 PC 46-33079W-03XG PIN BASE *3 TJC3-3A 1 P002 P2 - P4 FOR W. BAL PC 46-37030H-05XG HS 5P 2468#24 450 TJC3-5Y/SC

1 P201 P1 - P5 FOR CRT BD PC

Page 18

57-10654X-00F TWIST TIE NY66 3 PC 62-227680-0UA BRACKET ABS-KINGFA 606 (UO) 1 PC 64-P30080-104G M/C SCREW P 3 X 8 3 FOR Q414;FOR IC301;FOR QPC 64-P30100-104G M/C SCREW P 3 X 10 2 FOR IC602 PC 65-Z30050-23MG NUT M 3 2 FOR IC301 & Q411 PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

10 FOR T402(1,2,4,5,6,7,8,9PC

66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

5 FOR Q411;"FOR C413(1,2)" PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

6 FOR C412(1,2);FOR C414(1 PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

6 FOR C411(1,2);"FOR C419(PC 66-382330-0B7 RIVET 2.0X3.7X3.5 6 FOR Q414;FOR IC602;FOR RPC 67-H27292-1A0 HEAT SINK 1 FOR Q414 PC 67-H30147-1A0 HEAT SINK 1 FOR Q411 PC 67-H30179-7A0 HEAT SINK 1 FOR IC301 PC 67-H34423-BA0 HEAT SINK 1 FOR IC602 PC 10-0001H8-FBX DIODE 1H8 (FAST RECOVERY) 1 D851 PC 10-00RU4C-F0X DIODE RU4C (FAST RECOVERY) 1 D831 PC 10-0EU2YX-FBX DIODE EU2YX (FAST RECOVERY) 1 D832 PC 10-0RU4YX-F0X DIODE GRU4YX (FAST RECOVERY) 1 D833 PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 2 D807;D808 PC 10-CW574C-DJX DIODE CW574CD 1 D824 PC 10-D3SB60-H7X DIODE SHD-D3SB60-7109 1 DB801 PC 11-C144ES-0BX TRANSISTOR PDTC144ES (NPN) 2 Q804;Q803 PC 11-P08P06-0AX TRANSISTOR SPP08P06P 1 Q802 PC 11-SK3451-0CX TRANSISTOR 2SK3451-01MR 1 Q801 PC 13-000TL4-31T IC TL431ACLP 1 IC803 PC 13-0HPC92-2BP IC HPC922B 1 IC802 PC 13-0L7805-CVS +5V 1.5A IC L7805CV 1 IC805 PC 13-0L7809-CVS IC L7809 SGS (TO-220) 1 IC804 PC 13-DA1684-62P IC TDA16846-2(Q67040-S4494) 1 IC801 PC 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R813 PC 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 2 R807;R833 PC 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5

1 R834A PC 18-CB0123-JNX RES. C.F. 12K OHM 1/6W +/-5% 1 R805 PC 18-CB0182-JNX RES. C.F. 1.8K OHM 1/6W +/-5

1 R841 PC 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R809 PC 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5

1 R839 PC 18-CB0303-JNX RES. C.F. 30K OHM 1/6W +/-5% 1 R808 PC 18-CB0333-JNX RES. C.F. 33K OHM 1/6W +/-5% 2 R837;R806 PC 18-CB0513-JNX RES. C.F. 51K OHM 1/6W +/-5% 1 R804 PC 18-CD0102-JNX RES. C.F. 1K OHM 1/4W +/-5% 1 R811 PC 18-CD0221-JNX RES. C.F. 220 OHM 1/4W +/-5% 1 R838 PC 18-CD0470-JNX RES. C.F. 47 OHM 1/4W +/-5% 2 R808A;R810 PC 18-CE0332-JNX RES. C.F. 3.3K OHM 1/2W +/-5

1 R843 PC 18-FE0124-JNX RES. M.O. 120K OHM 1/2W +/-5

1 R840 PC 18-FG0104-JHX RES. M.O. 100K OHM 2W +/-5% 2 R852;R851 PC 18-FG0221-JHX RES. M.O. 220 OHM 2W +/-5% 1 R834 PC 18-FG0330-JHX RES. M.O. 33 OHM 2W +/-5% 1 R832 PC

Page 19

18-FG0822-JHX RES. M.O. 8.2K OHM 2W +/-5% 1 R842 PC 18-FH0223-JLX RES. M.O. 22K OHM 3W +/-5% 1 R831 PC 18-KE0105-JN3 RES. H.VOLT. CC 1M OHM 1/2W

3 R801;R802;R808B PC 18-KE0475-JNX RES. GLASS GLAZE 4.7M OHM 1/

1 R803 PC 18-KF0825-JH3 RES. H.VOLT.CC 8.2M OHM 1W +

1 R835 PC 20-TR102H-5CX TRIMMER B1K HORIZ TYPE 1 VR821 PC 22-NTC479-XX0 NTC 4.7 OHM +/-18% NTC4.7D2-

1 RT802 PC 22-PTC909-3A5 PTC 9 OHM 1 RT801 PC 25-BCA102-M1X CAP. ELEC 1000 UF 16V +/-20% 1 C842 PC 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C836A PC 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C845A PC 25-BDA222-M1S CAP. ELEC 25V/2200UF/+/-20% 1 C838 PC 25-BDB101-M1X CAP. ELEC 100 UF 25V +/-20% 1 C816 PC 25-BDB470-M1X CAP. ELEC 47 UF 25V +/-20% 1 C840 PC 25-BJG221-M1X CAP. ELEC 220 UF 160V +/-20% 1 C835 PC 25-KEG222-M1X CAP. ELEC 2200 UF 35V +/-20% 1 C839 PC 25-KJG101-M1X CAP. ELEC 100 UF 160V +/-20% 1 C824 PC 26-ABC104-ZFX CAP. CER 0.1 UF 50V +80-20%

2 C846A;C838A PC 26-ABC182-KBX CAP CER 1800 PF 50V +/-10% B 1 C810 PC 26-ABC681-JZX CAP. CER 680 PF 50V +/-5% SL 1 C815 PC 26-AIC221-KBX CAP. CER 220 PF 500V +/-10%

2 C833;C832 PC 26-AIL103-KBX CAP.CER 10NF 500V +/-10% 2 C825A;C807 PC 26-AMM221-JZX CAP. CER 220PF 2KV +/-5% SL 2 C831;C852 PC 26-AMM331-JZX CAP. CER 330 PF 2KV +/-5% SL 1 C834 PC 26-AMM561-KDX CAP. CER 560 pF 2KV +/-10%

1 C817 PC 26-APK102-ME4 CAP. CER 1000PF 400VAC+/-20% 2 C805A;C804A PC 26-APK222-ME4 CAP. CER 2200PF 400VAC+/-20% 1 C830 PC 26-AQK472-ZFX CAP. CER 4700PF 250VAC +80% -

2 C804;C805 PC 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% 4 C811;C812;C841;C816A PC 26-EBP104-ZFS CAP. CER 0.1UF 50V +80%/-20% 1 C839A PC 26-EBP331-JCS CAP. CER 330PF 50V +/-5% 1 C813 PC 26-EBP560-JCS CAP. CEP 56PF 50V +/-5% 1 C814 PC 27-AQQ683-K0X CAP. M.PP 0.068 UF 250VAC +/

1 C851 PC 27-AQT224-MV3 CAP.M.PP 0.22UF 250VAV +/-20

1 C801 PC 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C844 PC 27-MBC224-J0X CAP. M.P.E 0.22UF 63V +/-5% 2 C822;C821 PC 27-MHM104-K0X CAP. M.P.E 0.1 UF 400V +/-10

1 C803 PC 27-PBC103-J0X CAP. P.E. 0.01UF 63V +/-5% 1 C850 PC 34-R101K2-1BX COIL CHOKE 100 UH +/-10% 2 L825;L824 PC 35-139730-00X FERR. BEAD BF60 4 FOR D832;FOR L801 PC 35-237250-00X FERR. BEAD HF70 4.5X5.0 4 FOR D833;FOR D831 PC 36-LIF022-AX0 LINE FILTER 1 T801 PC 36-TRF127-AX2 TRANSFORMER CONV. BCK-4922 1 T803 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 3 J830;J823;J824 PC 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 1 J809 PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J822 PC 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J802A PC

Page 20

41-WJ0105-B00 WIRE BARE JUMPER 10.5MM 1 J814 PC 41-WJ0110-B00 WIRE BARE JUMPER 11MM 2 J817;J815 PC 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 3 J811;J819;J812 PC 41-WJ0135-B00 WIRE BARE JUMPER 13.5MM 1 J805 PC 41-WJ0150-B00 WIRE BARE JUMPER 15MM 3 J807;J820;L801 PC 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM 3 J808;J813;J816 PC 41-WJ0180-B00 WIRE BARE JUMPER 18MM 1 J806 PC 41-WJ0195-B00 WIRE BARE JUMPER 19.5MM 1 J810 PC 46-10962W-02XG PIN BASE *2 TJC2-2A 1 P803 FOR DEGAUSSING COILPC 64-P30060-104G M/C SCREW P 3 X 6 2 FOR IC804 & IC805 PC 64-P30080-104G M/C SCREW P 3 X 8 1 FOR Q801 PC 66-20516X-0B0 FUSE HOLDER 2 FOR F801 PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

6 FOR L824;FOR DB801 PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

5 FOR C835(1,2);"FOR T801(PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

6 FOR T803(1,9,7,10,12,18) PC 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2

7 FOR C801(1,2);FOR RT801; PC 66-382330-0B7 RIVET 2.0X3.7X3.5 8 FOR IC804;FOR P803;FOR CPC 67-H27292-3A0 HEAT SINK 1 FOR IC805 PC 67-H27292-5A0 HEAT SINK 1 FOR IC804 PC 67-H35984-2A0 HEAT SINK 1 FOR Q801 PC 71-DYP000-WX1 LABEL 1 PC 10-1N4001-EBX DIODE 1N4001 (RECTIFIER) 1 D420 PC 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 2 R261;D208 PC 10-79C24V-DBX DIODE ZENER 24V 1/2W 5% 1 D210 PC 10-79C2V4-DBX DIODE ZENER 2V4 1/2W 5% 1 D209 PC 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q205 PC 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q202 PC 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5

1 R253 PC 18-CB0121-JNX RES. C.F. 120 OHM 1/6W +/-5% 1 R250 PC 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R251 PC 25-BFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% 2 C249;C443 PC 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R249 PC 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J401 PC

Page 21

4 M134 Alignment Procedures

A. Enter Factory Mode:

Simply press the “SERVICE” key on the factory remote handset.

Press““““1，，，，2，，，，3，，，，4，，，，5，，，，6，，，，7，，，，8，，，，9，，，，0，，，，NOTEBOOK,CAPS, DISPLAY ,SLEEP, CALENDAR ,COLOR/INS，，，， FAVORITE,RECALL””””, you can switch in the sub-menus of ““““FAC01～～～～FAC18””””in turns.

Press ““““P+”“

”“”“

”“ P-””””to choose the items.

Press““““V+”“

”“”“

”“ V-””””to adjust the data.

Press ““““OK”””” and ““““P+”“

”“”“

”“ P-””””to switch in the sub-menus of ““““FAC19～～～～FAC23””””.

Exit Factory Mode:

Press the “SERVICE” key on the factory remote handset. All changes in factory data will be saved in

EEPROM automatically.

Some special modes:

Aging Mode ———— Be used for aging before adjustment in Factory Mode.

Vertical doesn’t Work ———— Be used for Screen & Focus voltage adjustment. In Factory

Mode, press ““““TV/AV””””to enter and exit.

White balance adjustment Mode ———— Be used for White balance adjustment. In Factory

Mode, press““““BUS OFF”””” to enter and exit.

Default Value OK mode ———— Be used for default value setting before TV leaves Factory. In

Factory Mode, press “S. EFFECT” to enter default value.

“Wait” will be displayed in screen, when it is finished,

“OK” will be displayed. It will exit factory mode

automatically.

Note: Now press “SERVICE” cannot enter factory mode, you

have to take the following steps to enter:

1. Setting Volume to Zero.

2. Press “V-” in cabinet and Press “Display” in RC

simultaneously.

B. Adjustment Way

1. B＋＋＋＋Adjustment：：：： Apply Philips Test pattern signal in normal status, adjusting VR821 to make B＋＝

＋＝＋＝

＋＝130V±±±±0.5V.

2. RF AGC adjustment:

Observe monitor the collector waveform of Q101 with the probe of Oscilloscope as illustration

below. Select channel 2 (>70dB) from the antenna input. Enter D-mode, select menu6 to adjust

RFAGC item until the monitor peak value to 0.8Vp-p.

Page 22

IN60

3Pf

输出

输入

3. Sound Amplifier Adjustment:

1) Apply 45.75 IF signal which is >60dB from P1101

2) Adjusting T1101 to make the voltage of Pin 15 in IC1101 is 2.5+

0.05V.

4. Screen & Focus voltage adjustment:

1) Apply pattern signal in normal status, enter D-mode, press “TV/AV” button to turn off the vertical

output. (Note: The default value of RC/GC/BC is 80, and GD/BD is 40)

2) Adjust the SCRREEN switch on the flyback transformer to make a horizontal shining line just visible

on the screen.

3) Turn on the vertical output, adjust the “FOCUS” on the flyback transformer to obtain the optimum

focus.

5. White balance adjustment (NORMAL)

1) Apply Black and White Signal in normal status, enter into Factory Mode and select Menu 1.

2) Using analyzer to test the black signal part, adjust RCUT, GCUT, BCUT to make X=284, Y=299.

3) Using analyzer to test the white signal part, adjust BDRV, GDRV to make X=284, Y=299.

4) Adjusting Brightness and Contrast from Min to Max, repeat step 2)~3) to make X=284, Y=299.

Note: M134 chassis can adjust white balance automatically. In factory mode, press “I2C BUS” to enter in.

The white balance in the other two colors temperature is Warm (296, 296), Cool (279, 265).

6. Adjustment of Sub-brightness:

1) Apply the Grey-scale/Color bar (NTSC signal) to the AV input, in normal status.

2) Enter into Factory Mode and select Menu 5, select BRTC to adjust the sub-brightness, until that the

2nd dark bar of 8 level Grey scale just can be seen.

7. Picture geometric adjustment:

1) Apply the Philips standard testing pattern in normal status, then enter menu 3, adjusting the

following data to get the min-distortion.

HPOS5/6

（（（（

Horizontal Center

））））

PARA5/6

（（（（

Level

））））

TRAP5/6

（（（（

Trapezia

））））

HSIZE5/6

（（（（

Horizontal Size

））））

CNRT5/6

（（（（

Top

））））

CNRB5/6

（（（（

Bottom

））））

2) Apply the Philips standard testing pattern in normal status, then enter menu 3, adjusting the

following data to get the min-distortion.

HIGH5/6 (Height) VP50/60

（（（（

Vertical Center

））））

VLIN5/6

（（（（

Linearity

））））

VSC5/6

（（（（

Vertical-S Correction

））））

8. BTSC/SAP Function checking:

It needn’t to adjust the BTSC/SAP, but you have to check where it does work.

9. CCD and V-CHIP function checking:

INPUT

OUTPUT

Page 23