Sampo 21000000000, 21E09 Service Manual

Page 1

SAMPO

SERVICE MANUAL

21E09

1、 Caution………………………………………………………………………2 2、 Specification…………………………………………………………………6 3、 BOM list ……………………………………………………………………9

4、 Alignment Procedure………………… … …………………………… …24

5、 Block Diagram………………………………… …………………………33 6、 Schematic Diagram……………………… ……… ………………………34

7、 PCB Layout……………………………… …………………………………35

8、 Explode V iew Diagram………………… …………………………………36

9、Troubleshooting……………………… ……… ………………………… 37

This manual is the latest at the time of printing, and does not include the modification which may be made after the printing, by the constant improvement of product

Page 2

WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION:

Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION

RISK RISK OF OF ELECTRIELECTRICC

SHOCK SHOCK DO DO NOT NOT OPEN.OPEN.

dangerous

Page 3

FOR YOUR PERSONAL SAFETY

1. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.

4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

5. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set.

6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to qualified service personnel.

8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.

9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a car t or stand recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and should use a mounting kit approved by the manufacturer.

10.2. An appliance and car t combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

CAUTION:

Read all of these instructions. Save these instructions for later use. Follow all Warnings and Instructions marked on the audio equipment.

1. Read Instructions- All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions- The safety and operating instructions should be retained for future reference.

3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions- All operating and use instructions should be followed.

IMPORTANT SAFETY INSTRUCTIONS

Page 4

PROTECTION AND LOCATION OF YOUR SET

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.

12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.

13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.

14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to protect it from overheating. These openings must not be blocked or covered.

Never cover the slots or openings with cloth or other material. Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. Never place the set near or over a radiator or heat register. Never place the set in enclosure, unless proper ventilation is provided.

PROTECTION AND LOCATION OF YOUR SET

15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some

protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrode, and requirements for the grounding electrode.

15.2. Note to CATV system installer : (Only for the television set with CATV reception)

This reminder is provided to call the CATV system attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power

circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning and power-line surges.

ANTENNA LEAD- IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

ELECTRIC SERVICE

EQUIPMENT

GROUND CLAMP

NEC-NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS

a built-in

installer s

Page 5

OPERATION OF YOUR SET

18.

This television set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.

19. If the television set does not operate normally by following the operating instructions, unplug this television set from the

wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television set to normal operation.

20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on

a holiday, turn the television set and unplug the television set from the wall outlet.

IF THE SET DOES NOT OPERATE PROPERLY

21. If you are unable to restore normal operation by following the detailed procedure in your operating instructions,

do not attempt any further adjustment. Unplug the set and call your dealer or service technician.

22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for

service, unplug the set and have it checked by a professional service technician.

23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being

turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service technician.

FOR SERVICE AND MODIFICATION

24. Do not use attachments not recommended by the television set manufacturer as they may cause hazards.

25. When replacement parts are required, be sure the service technician has used replacement parts specified

by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

26. Upon completion of any ser vice or repairs to the television set, ask the service technician to perform

routine safety checks to determine that the television is in safe operating condition.

off

Page 6

PFS2 FORMAT-1 Report

ProductView......:

Report by............:

Specs / Products

MasterData Customer Id

JET LTDA(CHILE)

Version

Status Locked 12NC Brand

HYUNDAI

EAN

UPC

Rece

tion

+Tunin

- presets/channels

181, Full-Cable

+Tunin

- technolo

PLL

+Tunin

- Indication

Full-Cable

+Fre

Bands

Freq

+Channels +IF Fre

45.75M

+TV S

stems Off Air/Cabl

NTSC-M, PAL MN

+Add S

stems Ext In

4.43 NTSC, 4.43PAL

+TV S

stems Multi

PAL NTSC

+Sound S

stems

AV STEREO

Picture - Processin

+Scan

Standard

+Scan Modes

4:3

+Wide Screen Switchin

+Combfilter +Picture Control

Brightness, Color, Contrast, Tint, Sharpness Con Var, Smart pict 4 modes

+Pict Enhancement

Blue Mute

+Pict Noise Reduction

Yes

Picture - Dis

play

+Display T

ype

+Screen Format +Size

(

Visual)" - size/vis. cm

21"

+Deflection S

stem (CRT onl

+Tube Technology (CRT onl

+CRT Defl +CRT Gun +CRT Ma

n field +Resolution +Coatin

g (

only for D.V. sets

)

+White Point Sound +Leaflet Power +RMS Power Intern

2X3W

+RMS Power Extern +Surround Sound ' +Sound Features

Mute, Smart sound(4 modes)

+Sound Control

Volume

Sound - S

eakers

eaker configuration

2 speakers

eakers used

eaker Size User Interface +Interface Name

2165

+Voice Control +Menu

Cursor Control

+Menu Colours +Menu Lan

guag

Spanish, English

+Special Features

Favorite channel, Notebook, Biological,Calendar

erational Features

+PP Features +Tuning/Install Features

Auto Cable/ Auto select. Auto channel Prog, Cable/Antenna select, Factory Mode, Language Selection, Service Mode

Product:

2004-6-3 16:22 1465 PFS 1 of 3

Page 7

ProductView......:

Report by............:

Specs / Products

Product:

+Clock/Timer Functions

sleep timer

+Local Controls Front

Channel +/-, Volume+/-, Mains(Tact Switch), Menu, TV/AV

+Local Controls To

+Indicators - screen +Indicators - front +Numb of Loc Cont

(

incl Mains

)

+Number of Ind. (incl Mains

)

+Local Controls (Old

)

Remote Control +Remote Control - sco

+Remote Control - t

Standard

+Remote Control - t

ypenr

RC115

+Remote Control - features Connectors Rea

+Scart RGB+Y/C+CVBS +Scart RGB+CVBS +Scart CVBS+Y/C +Com

onent In (Y/U/V) Cinch

+In Y/C+Cinch

(

CVBS+St

)

+In Y/C+Cinch(CVBS+Mo

)

+In Y/C+Cinch(St

)

+In BNC (CVBS

)

+In Cinch(CVBS+St

)

+In Cinch

(

CVBS+Mo

)

+Out Cinch(CVBS+St

)

+Out Cinch

(

CVBS+Mo

)

+Out Cinch Audio Stereo +Out Cinch Audio Mono +Out Cinch Dolb

Surround

+Di

Audio Out

+Louds

eakers +Control Busses +Feature Slot +ITV Smart Port +Terr. Antenna in

75 Ohms(F type)

Guide + IR Blaster Jack Connectors Fron

+In Cinch (CVBS + St

)

+In Cinch (CVBS+Mo

)

+Headphone Out

Connectors Side +In Y/C + Cinch

(

CVBS+St

)

+In Y/C + Cinch Stereo +In Cinch

(

CVBS + St

)

+IN Cinch

(

CVBS + Mo

)

+Headphone Out Connectors To

Connectors Mechanical St

lin

+Cabinet Name

2165

+Confi

uration

+Gra

hics/Logo's +Cabinet Colour and Finish +Mechanics +S

eaker Visibilit

General +Se

ment

+Chassis

M123A

+Software Deliver

Mode +Software Version +Mains Volta

110-240V

+Mains Fre

uenc

50 / 60 Hz

+Type Mains Cord

VDE

Power Consum

tion (P)TV in On

Power Consumption SB in Watts

less than 3W

Power Consum

tion Semi SB in W

+Power in "ON" for

2004-6-3 16:22 1465 PFS 2 of 3

Page 8

ProductView......:

Report by............:

Specs / Products

Product:

+Power in Standby for +Power in "OFF" for Wei

ht (P)TV (incl. Packagin

Weight (P)TV (excl. Package

)

Weight AVUnit excl Packagin

+INDICATION on BACKCOVE

+Channel Final E

quip

ment

+Packa

ging

- methods +Documents and manuals +Lan

guag

es DFU

+Cables Su

lied

+Antenna Su

lied

+Stand Su

lied

+Aux E

quip

m Supplied

Packa

ging

- width cm

Packa

ging

- height cm

Packa

ging

- depth cm Miscellaneous +EAN Indication +A

robation +Tests +Local Inte

ration Various Perf. Param. +Service Call-Rate PIP/POP +T

ype

+Features Di

ital Reception +Transmission Built-in Data S

stem +Text Standard +

(

Tele)text Features

+Nbr bck

rnd page / Mem Size

+Text Technolo

+Digital Data handlin

+Program Guide Built-in Clock/Timer +T

ype

+Features Built-in Radio +T

ype

Built-in PC displa

+PC Synch +PC Control Built-in DVD drive +T

e of Medium

e of Dec

Phased Out Items +Tuner/Frontend +Sensitivit

+CRT EHT +Li

htning Protection

+Accoun

+XX(Radio Antenna in

)

+Non Volatile Memor

+In Y/C + Cinch(CVBS+Mo

)

Version of deck

2004-6-3 16:22 1465 PFS 3 of 3

Page 9

Item Description Qty. Location T8-DE09AG-MA1SM ASS'Y - CHASSIS BD`TW' 1 T8-0D276G-CRY ASS'Y - CRT BD 1 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D502 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D501 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q510 11-SC2482-0BX TRANSISTOR 2SC2482 1 Q501 11-SC2482-0BX TRANSISTOR 2SC2482 1 Q502 11-SC2482-0BX TRANSISTOR 2SC2482 1 Q503 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R501 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R504 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R507 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R522 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 R524 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R525 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R526 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R527 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R502 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R505 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R508 18-CB0681-JNX RES. C.F. 680 OHM 1/6W +/-5% 1 R523 18-CB0751-JNX RES. C.F. 750 OHM 1/6W +/-5% 1 R503 18-CB0751-JNX RES. C.F. 750 OHM 1/6W +/-5% 1 R506 18-CB0751-JNX RES. C.F. 750 OHM 1/6W +/-5% 1 R509 18-CD0104-JNX RES. C.F. 100K OHM 1/4W +/-5% 1 R521 18-FE0272-JNX RES. M.O. 2.7K OHM 1/2W +/-5% 1 R514 18-FE0272-JNX RES. M.O. 2.7K OHM 1/2W +/-5% 1 R515 18-FE0272-JNX RES. M.O. 2.7K OHM 1/2W +/-5% 1 R518 18-FG0183-JHX RES. M.O. 18K OHM 2W +/-5% 1 R510 18-FG0183-JHX RES. M.O. 18K OHM 2W +/-5% 1 R511 18-FG0183-JHX RES. M.O. 18K OHM 2W +/-5% 1 R512 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C508 26-AIL103-KBX CAP.CER 10NF 500V +/-10% 1 C504 26-AMM221-JZX CAP. CER 220PF 2KV +/-5% SL 1 C505 26-EBP103-ZF1 CAP CER 50V 2.5MM 10nF -20%+80% 1 C514 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C507 35-139730-00X FERR. BEAD BF60 2 FOR C514 (L505 & L506) 40-02135S-CRF1XG CRT BD 1 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J505 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J502 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J503 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J501 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J504 46-10967W-01XG PIN BASE *1 TJC1-1A 1 P503 46-28816H-05XG HS 5P24 500 TJC3-5Y/SCN-5Y 1 P501 P2 -P6 FOR M.BD P201 46-30615H-04XG HS 4P24 460 F/W TJC3-4Y/SCN-4 1 P502 FOR M. BD P402 47-CRT004-XX0G CRT SOCKET GZS10-2-108 1 S501 26-EBP681-JCS CAP. CER 680 PF 50V +/-5% 1 C501 26-EBP681-JCS CAP. CER 680 PF 50V +/-5% 1 C502 26-EBP681-JCS CAP. CER 680 PF 50V +/-5% 1 C503 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 FOR Q504 (B - E) 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 FOR Q506 (B - E) 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 FOR Q508 (B - E) T8-0D276G-AVY ASS'Y - AV BD 1

Page 10

40-21189H-SIB1XG P.C.B. SIDE BD 1 46-35038H-05XG HS 5P24 380 TJC3-5Y/SCN-5Y 1 P904A R - V FOR M.BD P904 47-RCA139-XX0G JACK RCA RCA317 1 FOR P1101/P1102/P1103 T8-21E09G-KEY ASS'Y - KEY BD 1 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5% 1 R026 18-CB0182-JNX RES. C.F. 1.8K OHM 1/6W +/-5% 1 R025A 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5% 1 R024 18-CB0432-JNX RES. C.F. 4.3K OHM 1/6W +/-5% 1 R023 18-CB0682-JNX RES. C.F. 6.8K OHM 1/6W +/-5% 1 R022 40-21E09H-KEA1XG P.C.B. KEY BD 1 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J001 46-35168H-02X01G CONNECTOR TCL1009 1 P001A P2 - P3 FOR M. BD P006 48-TAC001-XX0 TACT SWITCH 1 S006 48-TAC001-XX0 TACT SWITCH 1 S005 48-TAC001-XX0 TACT SWITCH 1 S004 48-TAC001-XX0 TACT SWITCH 1 S003 48-TAC001-XX0 TACT SWITCH 1 S002 48-TAC001-XX0 TACT SWITCH 1 S001 T8-21E09G-SW1 ASS'Y - SWITCH BD 1 02-IRR001-XX1 IR RECEIVER MODULE HRM380017 1 IR1001 14-LED05R-XX1 LED RED FB205 1 D1001 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 R1004 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% 1 R1002 25-BCB220-M1X CAP. ELEC 22 UF 16V +/-20% 1 C1001 40-21E09H-SWD1XG P.C.B SWITCH BD 1 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 J1002 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R1013 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R1001 46-30407H-05XG HS UL2468#24 5C/TS 180 TJC3-5Y 1 P1001B FOR M. BD P005 46-39073H-03XG HS 2P 1617#22 200 TJC1-2Y/VH-3Y 1 FOR PWR SW. BD(P802) & PWR PARTS 46-39219W-03XG PIN BASE VH-3AW 1 P802 46-39219W-03XG PIN BASE VH-3AW 1 P801 FOR POWER CORD 48-POW001-AX0G SWITCH POWER 1 SW801 57-426610-0UG spacer support 2 58-414830-0UI PVC INLAY 1 62-226920-0HA LED HOLDER ABS-LG H121 (HB) 1 62-262660-0HN POWER SW.ADAPTER 1 66-382330-0B7 RIVET 2.0X3.7X3.5 4 FOR P801, P802 T8-DE09AG-MA1HM ASS'Y - MAIN BD`TW' 1 T8-0A21SG-MAY ASS'Y - MAIN BD 1 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R414 18-DE0563-FNX RES.MF 56K OHM 1/2W +/-1% 1 R831 18-EG0129-JHX RES. FUS. 1.2 OHM 2W +/-5% 1 R420 18-FF0122-JGX RES. M.O. 1.2K OHM 1W +/-5% 1 R411 18-FG0229-JHX RES. M.O. 2.2 OHM 2W +/-5% 1 R309 26-AMM681-KBX CAP. CER 680 PF 2KV +/-10% B 1 C402 27-AGQ394-JSX CAP. M.PP 0.39 UF 250VAC +/-5% 1 C421 27-ALR123-J0X CAP. M PP 0.012 UF 1.6KV +/-5% 1 C406B 36-LIN500-XX1 COIL LINEARITY 50 UH 1 L412 37-FBA001-CAA0A FBT 21" 1 T402 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 L411 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 1 D401 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 1 D402 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 1 D403

Page 11

10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 1 D404 10-1N4001-EBX DIODE 1N4001 (RECTIFIER) 1 D301 10-1N4002-EBX DIODE 1N4002 (RECTIFIER) 1 D405 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D005 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D006 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D007 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D008 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D009 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D206 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D302 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D303 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D305 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D307 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D601 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D602 10-79C3V9-DBX DIODE ZENER 3V9 1/2W 5% 1 D304 10-79C5V1-DBX DIODE ZENER 5V1 1/2W 5% 1 D001 10-79C8V2-DBX DIODE ZENER 8V2 1/2W 5% 1 D406 11-A124ES-0BX TRANSISTOR PDTA124ES (PNP) 1 Q005 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q001 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q004 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q212 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q604 11-C144ES-0BX TRANSISTOR PDTC144ES (NPN) 1 Q211 11-DD1555-0AX TRANSISTOR 3DD1555 1 Q402 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q003 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q202 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q210 11-SA1015-YBX TRANSISTOR ST2SA1015Y (PNP) 1 Q605 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q002 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q203 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q208 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q209 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q905 11-SC2482-0BX TRANSISTOR 2SC2482 1 Q401 11-SC3779-DBX TRANSISTOR 2SC3779D (RF AMPL) 1 Q101 13-00M24C-08P IC EEPROM 8K M24C08 (WRITE) 1 IC001 13-STV930-2BS IC STV9302B 1 IC301 13-0L7805-CVS +5V 1.5A IC L7805CV 1 IC402 13-0L7809-CVS IC L7809 SGS (TO-220) 1 IC401 13-TDA705-7AS IC TDA7057AQ (2X8W) 1 IC601 18-CB0100-JNX RES. C.F. 10 OHM 1/6W +/-5% 1 J217 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R009 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R218 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% 1 R228 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R013 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R029 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R051 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R116 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R234 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R415 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R901 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R902 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R920

Page 12

18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R922 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R924 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 J305 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R006 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R011 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R012 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R030 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R043 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R047 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R050 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R052 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5% 1 R031 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5% 1 R232 18-CB0121-JNX RES. C.F. 120 OHM 1/6W +/-5% 1 R227 18-CB0122-JNX RES. C.F. 1.2K OHM 1/6W +/-5% 1 R007 18-CB0123-JNX RES. C.F. 12K OHM 1/6W +/-5% 1 R212 18-CB0151-JNX RES. C.F. 150 OHM 1/6W +/-5% 1 R115 18-CB0151-JNX RES. C.F. 150 OHM 1/6W +/-5% 1 R117 18-CB0153-JNX RES. C.F. 15K OHM 1/6W +/-5% 1 R315 18-CB0220-JNX RES. C.F. 22 OHM 1/6W +/-5% 1 R001 18-CB0220-JNX RES. C.F. 22 OHM 1/6W +/-5% 1 R005 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R201 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R202 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R203 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R220 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R238 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R401 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 R044 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 R055 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R215 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R912 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R913 18-CB0224-JNX RES. C.F. 220K OHM 1/6W +/-5% 1 R206 18-CB0271-JNX RES. C.F. 270 OHM 1/6W +/-5% 1 R217 18-CB0271-JNX RES. C.F. 270 OHM 1/6W +/-5% 1 R233 18-CB0303-JNX RES. C.F. 30K OHM 1/6W +/-5% 1 R205 18-CB0331-JNX RES. C.F. 330 OHM 1/6W +/-5% 1 R219 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% 1 R046 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% 1 R218A 18-CB0333-JNX RES. C.F. 33K OHM 1/6W +/-5% 1 R602 18-CB0392-JNX RES. C.F. 3.9K OHM 1/6W +/-5% 1 R213 18-CB0392-JNX RES. C.F. 3.9K OHM 1/6W +/-5% 1 R214 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% 1 R002 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R119 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% 1 R208 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R003 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R004 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R015 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R311 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% 1 R216 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% 1 R245 18-CB0560-JNX RES. C.F. 56 OHM 1/6W +/-5% 1 R114 18-CB0561-JNX RES. C.F. 560 OHM 1/6W +/-5% 1 R209 18-CB0564-JNX RES. C.F. 560K OHM 1/6W +/-5% 1 R210

Page 13

18-CB0681-JNX RES. C.F. 680 OHM 1/6W +/-5% 1 R028 18-CB0683-JNX RES. C.F. 68K OHM 1/6W +/-5% 1 R211 18-CB0751-JNX RES. C.F. 750 OHM 1/6W +/-5% 1 R008 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% 1 R903 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% 1 R923 18-CB0821-JNX RES. C.F. 820 OHM 1/6W +/-5% 1 R118 18-CB0822-JNX RES. C.F. 8.2K OHM 1/6W +/-5% 1 R237 18-CB0822-JNX RES. C.F. 8.2K OHM 1/6W +/-5% 1 R606 18-CD0100-JNX RES. C.F. 10 OHM 1/4W +/-5% 1 R027 18-CD0101-JNX RES. C.F. 100 OHM 1/4W +/-5% 1 R621 18-DB0103-FNX RES. M.F. 10K OHM 1/6W +/-1% 1 R302 18-DB0104-FNX RES. M.F. 100K OHM 1/6W +/-1% 1 R303 18-DB0153-FNX RES. M.F. 15K 1/6W +/-1% 1 R244 18-DB0223-FNX RES. M.F. 1/6W 22K OHM +/-1% 1 R306 18-EF0109-JGX RES. FUS. 1 OHM 1W +/-5% (LS) 1 R403 18-EF0109-JGX RES. FUS. 1 OHM 1W +/-5% (LS) 1 R405 18-EF0109-JGX RES. FUS. 1 OHM 1W +/-5% (LS) 1 R409 18-EF0109-JGX RES. FUS. 1 OHM 1W +/-5% (LS) 1 R418 18-FF0102-JGX RES. M.O. 1K OHM 1W +/-5% 1 R408 18-FF0103-JGX RES. M.O. 10K OHM 1W +/-5% 1 R410 18-FF0123-JGX RES. M.O. 12K OHM 1W +/-5% 1 R406 18-FF0129-JGX RES. M.O. 1.2 OHM 1W +/-5% 1 R304 18-FF0221-JGX RES. M.O. 220 OHM 1W +/-5% 1 R336 18-FG0153-JHX RES. M.O. 15K OHM 2W +/-5% 1 R404 18-GJ0332-JUX1 RES.C.C.5W 3.3KOHM +/-5% 1 R402 18-RG0228-JHX RES. WIRE ROUND 0.22 OHM 2W +/-5% 1 R620 25-BCA102-M1X CAP. ELEC 1000 UF 16V +/-20% 1 C232 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C004 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C023 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C025 25-RCB100-M1X CAP.ELEC 10 UF 16V +/-20% 1 C220 25-RCB100-M1X CAP.ELEC 10 UF 16V +/-20% 1 C227 25-RCB100-M1X CAP.ELEC 10 UF 16V +/-20% 1 C231 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C311 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C603 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C901 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C902 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C907 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C016 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C101 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C211 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C240 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C605 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C900 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C903 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C418 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C906 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C082 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C202 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C423 25-BDA471-M1X CAP. ELEC 470 UF 25V +/-20% 1 C217 25-BDA471-M1X CAP. ELEC 470 UF 25V +/-20% 1 C415 25-BDA471-M1X CAP. ELEC 470 UF 25V +/-20% 1 C604 25-BDB221-M1X CAP. ELEC 220UF 25V +/-20% 1 C301

Page 14

25-BEA102-M1X CAP. ELEC 1000 UF 35V +/-20% 1 C413 25-BEB101-M1X CAP. ELEC 100 UF 35V +/-20% 1 C302 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C008A 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C203 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C208 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C214 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C915 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% 1 C916 25-BFB478-M1X CAP. ELEC 0.47 UF 50V +/-20% 1 C218 25-RFB479-M1X CAP.ELEC 4.7 UF 50V +/-20% 1 C104 25-RFB479-M1X CAP.ELEC 4.7 UF 50V +/-20% 1 C216 25-RFB479-M1X CAP.ELEC 4.7 UF 50V +/-20% 1 C304 25-RFB479-M1X CAP.ELEC 4.7 UF 50V +/-20% 1 C310 25-BHB100-M1X CAP. ELEC 10 UF 100V +/-20% 1 C420 25-PJA470-M1X CAP.CELE 47UF/160V/+/-20% 1 C411 25-BLA100-M1X CAP. ELEC 10 UF 250V +/-20% 1 C408 25-MFB228-K1X CAP.ELEC 0.22UF 50V +/-10% 1 C205 25-MFB478-K1X CAP.ELEC 50V 0.47UF +/-10% 1 C234 25-MFB478-K1X CAP.ELEC 50V 0.47UF +/-10% 1 C236 26-AIC102-KBX CAP. CER 1000 PF 500V +/-10% B 1 C401 26-AIC102-KBX CAP. CER 1000 PF 500V +/-10% B 1 C404 26-AIC391-KBX CAP. CER 390 PF 500V +/-10% B 1 C409 26-EBP101-JCS CAP. CER 100 PF 50V +/-5% 1 C001 26-EBP101-JCS CAP. CER 100 PF 50V +/-5% 1 C002 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C112 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C219 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C005 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C017 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C019 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C020 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C024 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C081 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C102 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C105 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C110 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C114 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C201 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C212 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C221 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C228 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C230 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C233 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C239 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C241 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C417 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C425 26-EBP152-KBS CAP. CER 1500PF 50V +/-10% 1 C209 26-EBP181-JCS CAP. CER 180 PF 50V +/-5% 1 C207 26-EBP222-KBS CAP. CER 2.2 NF 50V +/-10% 1 C014 26-EBP270-JCS CAP. CER 27 PF 50V +/-5% 1 C011 26-EBP272-KBS CAP. CER 2700PF 50V +/-10% 1 C210 26-EBP331-JCS CAP. CER 330PF 50V +/-5% 1 C018 26-EBP390-JCS CAP. CER 39PF 50V +/-5% 1 C021 26-EBP390-JCS CAP. CER 39PF 50V +/-5% 1 C022

Page 15

26-EBP391-JCS CAP. CER 390PF 50V +/-5% 1 C403 26-EBP391-JCS CAP. CER 390PF 50V +/-5% 1 C412 26-EBP470-JZX CAP. CER 47PF 50V +/-5% SL 1 C424 27-AGQ563-J0X CAP. M.PP 0.056 UF 250V +/-5% 1 C410 27-MBC103-J0X CAP. M.P.E 0.01UF 63V+/-5% 1 C215 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C242 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C309 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C610 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C909 27-MBC224-J0X CAP. M.P.E 0.22UF 63V +/-5% 1 C305 27-MBC474-J0X CAP. M.P.E 0.47UF 63V +/-5% 1 C601 27-MBC474-J0X CAP. M.P.E 0.47UF 63V +/-5% 1 C602 27-PBC222-J0X CAP. P.E 0.0022UF 63V +/-5% 1 C204 27-PBC222-J0X CAP. P.E 0.0022UF 63V +/-5% 1 C213 27-PBC472-J0X CAP. P.E 0.0047UF 63V +/-5% 1 C422 27-PBC472-J0X CAP. P.E 0.0047UF 63V +/-5% 1 C607 27-PBC472-J0X CAP. P.E 0.0047UF 63V +/-5% 1 C608 27-PBC822-J0X CAP. P.E 0.0082UF 63V +/-5% 1 C235 27-RCP333-J0X CAP. PP 0.033 UF 100V +/-5% 1 C405 34-A109K0-1IX COIL CHOKE 1 UH +/-10% 1 L102 34-A109K0-1IX COIL CHOKE 1 UH +/-10% 1 L103 34-A220K0-1IX COIL PL - 22UH +/-10% LGA0305-220K 1 L201 34-R100J2-0EX COIL PL - 10 UH +/-5% 1 L002 34-R220J2-0EX COIL PL - 22 UH +/-5% 1 L207 34-R220J2-0EX COIL PL - 22 UH +/-5% 1 L208 34-R330J2-0EX COIL PL - 33 UH +/-5% 1 L080 34-R330J2-0EX COIL PL - 33 UH +/-5% 1 L202 34-R829J2-0EX COIL PL - 8.2 UH +/-5% 1 L204 36-HDR001-AX1 TRANSFOR HOR. DRIVE (MAGNETIC CORE) 1 T401 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 L101 41-WJ0055-B00 WIRE BARE JUMPER 5.5 MM 1 J922 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J001 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J009A 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J101 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J203 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J210 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J211 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J907 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R200 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R204 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R207 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R249 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 1 J010 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 1 J208 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM 1 J301 41-WJ0070-B00 WIRE BARE JUMPER 7MM 1 J011 41-WJ0070-B00 WIRE BARE JUMPER 7MM 1 J012 41-WJ0070-B00 WIRE BARE JUMPER 7MM 1 J217A 41-WJ0070-B00 WIRE BARE JUMPER 7MM 1 J223 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J018 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J022 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J215 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J218 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J225

Page 16

41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J303 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J602 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J901 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J913 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J914 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J108 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J903 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J919 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J205 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J206 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J209 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J219 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J302 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J306 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J920 41-WJ0090-B00 WIRE BARE JUMPER 9MM 1 J212 41-WJ0090-B00 WIRE BARE JUMPER 9MM 1 J904 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM 1 J229 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM 1 J230 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM 1 J231 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM 1 J601 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J002 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J002A 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J003 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J017 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J102 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J110 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J111 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J221 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J402 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J910 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J911 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J917 41-WJ0105-B00 WIRE BARE JUMPER 10.5MM 1 J304 41-WJ0105-B00 WIRE BARE JUMPER 10.5MM 1 R406A 41-WJ0110-B00 WIRE BARE JUMPER 11MM 1 J016 41-WJ0110-B00 WIRE BARE JUMPER 11MM 1 J226 41-WJ0115-B00 WIRE BARE JUMPER 11.5MM 1 J604 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 1 J106 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 1 J216 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 1 R317 41-WJ0130-B00 WIRE BARE JUMPER 13MM 1 J006 41-WJ0130-B00 WIRE BARE JUMPER 13MM 1 J204 41-WJ0135-B00 WIRE BARE JUMPER 13.5MM 1 J014 41-WJ0140-B00 WIRE BARE JUMPER 14MM 1 J005 41-WJ0150-B00 WIRE BARE JUMPER 15MM 1 L402 41-WJ0160-B00 WIRE BARE JUMPER 16MM 1 J105 41-WJ0165-B00 WIRE BARE JUMPER 16.5MM 1 J013 41-WJ0165-B00 WIRE BARE JUMPER 16.5MM 1 J220 41-WJ0170-B00 WIRE BARE JUMPER 17MM 1 J401 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM 1 R045 41-WJ0195-B00 WIRE BARE JUMPER 19.5MM 1 J003A 41-WJ0200-B00 WIRE BARE JUMPER 20MM 1 J233 45-OSC8M0-0Y0 CRYSTAL 8.0MHZ 1 X001

Page 17

45-TRA4M5-0Y0 CER TRAP TPS 4.5MHZ 1 X201 46-12866W-02XG PIN BASE *2 S11-02Y 1 P601 FOR FRONT CAB.(SPK) 46-20598W-04XG PIN BASE *4 TJC1-4A 1 P401 FOR DY CONNECTER 46-33079W-02XG PIN BASE *2 TJC3-2A 1 P602 FOR FRONT CAB.(SPK) 46-33079W-03XG PIN BASE *3 TJC3-3A 1 P001 46-33079W-05XG PIN BASE *5 TJC3-5A 1 P201 FOR CRT BD 46-35179W-04XG PIN BASE TJC3-4A 1 P402 FOR CRT BD P502 57-10654X-00F TWIST TIE NY66 3 62-227680-0UA BRACKET ABS-KINGFA 606 (UO) 1 64-P30060-104G M/C SCREW P 3 X 6 2 FOR IC401 & IC402 64-B30100-104G M/C SCREW B 3 X 10 2 FOR IC601 64-P30100-104G M/C SCREW P 3 X 10 2 FOR Q402 & IC301 65-Z30050-23MG NUT M 3 2 FOR Q402 & IC301 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 2 FOR L411 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 2 FOR L412 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 3 FOR Q402 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 4 FOR C421,C406B 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 9 FOR T402 66-343740-0B0 HOLLOW RIVET (2.3MMX4.0MMX3.5MM) 2 FOR R402 67-H24249-2M2 HEAT SINK 1 FOR IC402 67-H24249-3M2 HEAT SINK 1 FOR IC401 67-H30752-3A0 HEAT SINK 2 FOR IC301 & Q402 67-H34423-EA0 HEAT SINK 1 FOR IC601 10-79C6V2-DBX DIODE ZENER 6V2 1/2W 5% 1 D207 10-79C10V-DBX DIODE ZENER 10V 1/2W 5% 1 FOR (-)& P28/IC201 TO (+)接IC201底部

地

10-79C10V-DBX DIODE ZENER 10V 1/2W 5% 1 FOR (-)& P29/IC201 TO (+)接IC201底部

地

10-79C6V2-DBX DIODE ZENER 6V2 1/2W 5% 1 FOR (-)& P43/IC201 TO (+)接IC201底部

地

10-CW574C-DJX DIODE CW574CD 1 FOR C106 (DIODE“+” TO GND) 25-BFB220-M1X CAP. ELEC 22 UF 50V +/-20% 1 FOR D101 (CAPACITOR“-” TO GND) T8-0A21SG-PW2 ASS'Y - POWER BD 1 10-00RU3C-FBX HIGH EFFICIENCY RECTIFIER RU3C 1 D831 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) 1 D833 10-0RL255-EBX DIODE RL255 OR RL206(POWER RECTIFIER) 1 D815 10-0RL255-EBX DIODE RL255 OR RL206(POWER RECTIFIER) 1 D816 10-0RL255-EBX DIODE RL255 OR RL206(POWER RECTIFIER) 1 D817 10-0RL255-EBX DIODE RL255 OR RL206(POWER RECTIFIER) 1 D818 10-0RU3YX-FBX DIODE RU3YX 1 D830 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D805 10-1SS136-ABX DIODE 1SS136 1 D804 10-1SS136-ABX DIODE 1SS136 1 D835 10-79C8V2-DBX DIODE ZENER 8V2 1/2W 5% 1 D839 10-HER108-FBX DIODE HER108 1 D806 10-HS16VC-DBX DIODE 500MW 16HSC 1 D838 10-HS6V2B-DBX DIODE 6V2 500MW 1 D840 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q832 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q831 11-SC2688-LAX TRANSISTOR 2SC2688L (NPN) 1 Q830 11-SK2996-0AX TRANSISTOR 2SK2996 (MOS) 1 Q801 13-0HPC92-2CP PHOTO COUPLER HPC922-C 1 IC802 13-44608P-40P IC MC44608P40G 1 IC801 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R809 18-CB0183-JNX RES. C.F. 18K OHM 1/6W +/-5% 1 R838 18-CB0183-JNX RES. C.F. 18K OHM 1/6W +/-5% 1 R844 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% 1 R834

Page 18

18-CB0392-JNX RES. C.F. 3.9K OHM 1/6W +/-5% 1 R807 18-CB0472-JNX CARBON RES. C.F. 4.7K OHM 1/6W +/-5% 1 R806 18-CB0682-JNX RES. C.F. 6.8K OHM 1/6W +/-5% 1 R850 18-CD0220-JNX RES. C.F. 22 OHM 1/4W +/-5% 1 R811A 18-CD0221-JNX RES. C.F. 220 OHM 1/4W +/-5% 1 R833 18-CD0392-JNX RES. C.F. 3.9K OHM 1/4W +/-5% 1 R835 18-CD0471-JNX RES. C.F. 470 OHM 1/4W +/-5% 1 R811 18-CE0479-JNX RES. C.F. 4.7 OHM 1/2W +/-5% 1 R832 18-DD0104-FNX RES. M.F 100K OHM 1/4W +/-1% 1 R804 18-DD0912-FNX RES. M.F. 9.1K OHM 1/4W +/-1% 1 R804A 18-FG0333-JHX RES. M.O. 33K OHM 2W +/-5% 1 R837 18-GJ0103-KUX1 RES.C.C.5W 10KOHM +/-10% 1 R836 18-GJ0223-KUX1 RES.C.C.5W 22KOHM +/-10 1 R808 18-KE0105-JN3 RES. H.VOLT. CC 1M OHM 1/2W +/-5% 1 R802 18-KF0825-JH3 RES. H.VOLT.CC 8.2M OHM 1W +/-5% 1 R812 18-RG0228-JHX RES. WIRE ROUND 0.22 OHM 2W +/-5% 1 R810 20-TR103H-5CX TRIMMER B10K HORIZ TYPE 1 VR830 22-NTC479-XX0 NTC 4.7 OHM +/-18% NTC4.7D2-14 1 RT802 22-PTC200-XX1 PTC 20 OHM +/-20% 1 RT801 25-BDA222-M1S CAP. ELEC 25V/2200UF/+/-20% 1 C832 25-BCA102-M1X CAP. ELEC 1000 UF 16V +/-20% 1 C849 25-BDA102-M1X CAP. ELEC 1000 UF 25V +/-20% 1 C843 25-BDB220-M1X CAP. ELEC 22 UF 25V +/-20% 1 C845 25-BFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% 1 C812 25-PJG101-M1X CAP.CELE 100UF/160V/+/-20% 1 C835 25-BKJ331-M1X CAP. ELEC 330 UF 200V +/-20% 1 C806 26-ABC101-JZX CAP. CER 100 PF 50V +/-5% SL 1 C814 26-ABC104-ZFX CAP. CER 0.1 UF 50V +80-20% F 1 C813 26-ABC104-ZFX CAP. CER 0.1 UF 50V +80-20% F 1 C831 26-ABC104-ZFX CAP. CER 0.1 UF 50V +80-20% F 1 C842 26-ABC221-JZX CAP. CER 220 PF 50V +/-5% SL 1 C841 26-ABC471-JZX CAP. CER 470 PF 50V +/-5% SL 1 C851 26-AGA221-KRX CAP.CER 220PF 250V +/-10% 1 C830 26-AIL103-KBX CAP.CER 10NF 500V +/-10% 1 C834 26-AIL103-KBX CAP.CER 10NF 500V +/-10% 1 C805 26-AKM221-KRX CAP. CER 220 PF 1KV +/-10% 1 C833 26-AMM102-KRX CAP. CER 1000 PF 2KV +/-10% R 1 C815 26-APK222-ME4 CAP. CER 2200PF 400VAC+/-20% E 1 C816 26-APK471-KBX CAP. CER 470PF 400VAC +/-10% B 1 C803 26-APK471-KBX CAP. CER 470PF 400VAC +/-10% B 1 C804 26-AQK472-ZFX CAP. CER 4700PF 250VAC +80% -20% F 1 C807 26-AQK472-ZFX CAP. CER 4700PF 250VAC +80% -20% F 1 C808 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C804A 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C848 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C844 27-AQT474-MVX CAP. M.PP 0.47 UF 250V +/-20% 1 C801 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 SOLDER ON R838 27-MBC104-J0X CAP. M.P.E 0.1 UF 63V +/-5% 1 C850 27-RJP472-J0X CAP. PP 0.0047 UF 630V +/-5% 1 C809 34-R100K2-1BX COIL CHOKE 10 UH +/-10% 1 L843 34-R101K2-1BX COIL CHOKE 100 UH +/-10% 1 L804 35-139730-00X FERR. BEAD BF60 2 FOR D833 35-139730-00X FERR. BEAD BF60 2 FOR D831 35-139730-00X FERR. BEAD BF60 2 FOR D830

Page 19

35-139730-00X FERR. BEAD BF60 2 FOR D806 36-LIF005-AX0 LINE FILTER 1 T801 36-TRF110-XX0 TRANSFORMER 1 T803 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 R820 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 R821 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 R822 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J809 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 D838A 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J821 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 J812 41-WJ0090-B00 WIRE BARE JUMPER 9MM 1 J805 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J820 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 J822 41-WJ0100-B00 WIRE BARE JUMPER 10MM 1 R807A 18-CD0100-JNX RES. C.F. 10 OHM 1/4W +/-5% 1 R851 41-WJ0105-B00 WIRE BARE JUMPER 10.5MM 1 J824 41-WJ0115-B00 WIRE BARE JUMPER 11.5MM 1 J832 41-WJ0120-B00 WIRE BARE JUMPER 12MM 1 J823 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM 1 J804 41-WJ0135-B00 WIRE BARE JUMPER 13.5MM 1 J833 41-WJ0150-B00 WIRE BARE JUMPER 15MM 1 J826 41-WJ0150-B00 WIRE BARE JUMPER 15MM 1 J802 41-WJ0160-B00 WIRE BARE JUMPER 16MM 1 J825 41-WJ0165-B00 WIRE BARE JUMPER 16.5MM 1 J831 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM 1 J807 41-WJ0190-B00 WIRE BARE JUMPER 19MM 1 J811 41-WJ0195-B00 WIRE BARE JUMPER 19.5MM 1 J828 41-WJ0195-B00 WIRE BARE JUMPER 19.5MM 1 J829 41-WJ0200-B00 WIRE BARE JUMPER 20MM 1 J830 46-10962W-02XG PIN BASE *2 TJC2-2A 1 P801 64-B30100-104G M/C SCREW B 3 X 10 1 FOR Q801 66-20516X-0B0 FUSE HOLDER 2 FOR FUSE 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 4 FOR T803 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 3 FOR RT801 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 10 FOR C835,C801,L804,D831,D830 66-343730-0B0 HOLLOW RIVET 1.6MMX3.0MMX3.2MM 4 FOR T801 66-343740-0B0 HOLLOW RIVET (2.3MMX4.0MMX3.5MM) 8 FOR R808,R836,C806,P801 67-H35984-5A0 HEAT SINK 1 FOR Q801 71-DYP000-WX1 LABEL 1 STICK ON HEAT SINK 18-FE0102-JNX RES. M.O. 1K OHM 1/2W +/-5% 1 R813 T8-DE09AG-OT1 ASS'Y - OTHER PARTS`TW' 1 07-457FF5-NX8G TUNER TEDH9-251B 1 TU101 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q006 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q902 11-C124ES-0BX TRANSISTOR PDTC124ES (NPN) 1 Q904 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q602 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q603 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q609 13-000040-53P IC 4053 (ANALOG SW) 1 IC901 13-000040-66P IC HFE4066BP 1 IC902 13-T7M123-03M01 MCU TMPA8823CRNG 1 IC201 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R612A 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R613A 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R637

Page 20

18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R911 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R925 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R927 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R928 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R930 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% 1 R931 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R917 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R010 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% 1 R919 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R613 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R612 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R907 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R908 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R909 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% 1 R910 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% 1 R929 18-CE0479-JNX RES. C.F. 4.7 OHM 1/2W +/-5% 1 R918 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C919 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% 1 C920 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C921 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% 1 C904 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C918 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% 1 C009 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C928 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% 1 C926 26-EBP102-KBS CAP. CER 1000 PF 50V +/-20% 1 C306 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C905 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C917 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C925 26-EBP103-ZFX CAP. CER 0.01UF 50V +80/-20% F 1 C927 40-2111SG-MAM1XG P.C. B MAIN BD 1 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 J201 41-WJ0050-B00 WIRE BARE JUMPER 5MM 1 J906 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 J905 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J603 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 J912 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J915 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 J916 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J908 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J835 41-WJ0080-B00 WIRE BARE JUMPER 8 MM 1 J836 41-WJ0090-B00 WIRE BARE JUMPER 9MM 1 J909 45-SAWF18-590 SAW FILTER F1859 1 Z101 46-33079W-02XG PIN BASE *2 TJC3-2A 1 P006 P1 - P2 FOR KEY BD P001A 46-33079W-05XG PIN BASE *5 TJC3-5A 1 P005 FOR PWR SW. BD P1001B 46-33079W-05XG PIN BASE *5 TJC3-5A 1 P904 P3 - P7 FOR SIDE AV BD 47-RCA035-XX0G RCA JACK AV-3.2-6W-K 1 P901 50-03150D-1US7G FUSE 250V/3.15A 1 F801 70-271510-00A SERVICE CARD 1 FOR PRODUCTION USE 71-270870-0A9 LABEL 2 90-0DSTG1-SR1U HEAT SINK DSTG-1 0.6 FOR Q801 90-269080-ZU0U CLEAN COATING TC-131L 14KG/BARREL 0.1 10-79C9V1-DBX DIODE ZENER 9V1 1/2W 5% 1 FOR Q904 B 极接（-）& E 极接（+） 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM 1 D205 并将IC201的第22、23脚加锡相连

Page 21

46-28559W-02XG PIN BASE *2 TJC1-2A 1 P802 51-DC0243-0DN08G POWER CORD CEE 1 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R025 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R024 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R023 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R022 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R021 41-WJ0060-B00 WIRE BARE JUMPER 6MM 1 R020 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM 1 R026 T8-0A21SG-XR1 ASS'Y - X-RAY 1 10-1N4001-EBX DIODE 1N4001 (RECTIFIER) 1 D410 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 J004 (-) TO Q251(E) 10-1N4148-ABX DIODE 1N4148 (SWITCHING) 1 D251 10-79C20V-DBX DIODE ZENER 20V 1/2W 5% 1 D253 11-2SA817-AAX TRANSISTOR 2SA817AY 1 Q251 11-SC1815-YBX TRANSISTOR 2SC1815-Y (NPN) 1 Q250 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5% 1 R253 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% 1 R257 18-CB0331-JNX RES. C.F. 330 OHM 1/6W +/-5% 1 R256 18-DB0750-FNX RES. M.F. 75 OHM 1/6W +/-1% 1 R255 18-DD0391-FNX RES. M.F. 390 OHM 1/4W +/-1% 1 R254 18-EE0109-JNX RES. FUS. 1 OHM 1/2W +/-5% 1 R407 25-BFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% 1 C431 41-WJ0110-B00 WIRE BARE JUMPER 11MM 1 J007 41-WJ0170-B00 WIRE BARE JUMPER 17MM 1 J008 T8-21OFLN-SG1GAA1 ASS'Y - MATCH TUBE`67-1E0'(W/O CRT) 1 T8-21OFLN-FSG1GA1 ASS'Y - MATCH TUBE`67-1E0'(W/O CRT) 1 T8-21OFLN-MSG1GAA ASS'Y - METCH TUBE NOMINAL(M.BD) 1 T8-250250-SKY ASS'Y - SKD PACKING 1 74-045045-40F POLYBAG W/ANTISTATIC MAIN PCB 1 75-369900-C00 SKD POLYFOAM BASIN 1.17 76-002135-0AC CARTON BOX 0.042 74-015020-50Q PLASTIC BAG 1 FOR CRT BD PACKING T8-325000-SKY ASS'Y - SKD PACKING 1 75-388320-CC0 POLYFOAM BOARD 0.05 FOR PMC 89-242080-JZ0 TRANSPARENT PACKING (6CMX41M) 1.3 FOR PMC T8-21E09G-FCY ASS'Y - FRONT CABINET 1 46-27688H-04XG HS 4P A/B 400/13 RBGW TJC1/4Y 1 P401H FOR D.Y COIL

1 44-21OFLN-SG1A 67-325570-1E0 CRT METAL MTG 4 02-GND021-XX0G ASS"Y - CRT GND WIRE&HOUSE 1 36-DEG210-BX3 DEGAUSSING COIL 2500MM 1 42-51216D-XX0G SPEAKER (50MMX120MM) 16 OHM 5W 1 W602 42-51216D-XX0G SPEAKER (50MMX120MM) 16 OHM 5W 1 W601 46-27250H-02XG HS 2P24 450/5 F/W TJC3-02H 1 P602H FOR M. BD P602 46-37144H-02XG HS 2P 2468#22 450MM S11-2Y/7MM 1 P601H FOR M. BD P601 54-113970-0U0 PVC TUBE AWG NO.5 0.32 FOR SPK HOUSING 54-114000-00X FELT TAPE (150MMX19MMX0.3MM) 4 54-205140-000 SPACER CRT MOUNTING T=2MM 4 MTG CRT & F. CAB. 54-314740-0X0 CRT FIBRE SHEET (22MMX22MMX0.8MM) 8 MTG CRT TO F.CAB 57-10654X-00F TWIST TIE NY66 10 59-130460-00X RUBBER PAD (25MMX7MM) 2 STICK ON F.CAB(FOOTING) 59-312160-000 SPEAKER RUBBER CUSHION 8 62-395050-0UN MAIN BD RAIL (SMALL) 1

Page 22

62-406120-0UN TRACK 1 63-B40150-AB4G S/T SCREW B 4 X 15 AB 12 MTG CRT BKT & F. CAB. 63-W30080-AB4G S/T SCREW W 3 X 8 AB 1 MTG LENS & F. CAB. 63-W30100-AB4G S/T SCREW W 3 X 10 AB 3 MTG KEY BD & F. CAB. 63-W30100-AB4G S/T SCREW W 3 X 10 AB 1 MTG 62-395050-0UN 63-W30120-AB4G S/T SCREW W 3 X 12 AB 8 MTG SPEAKER 63-Z30100-AB4G S/T SCREW 3.0 X 10 2 MTG POWER SW. BD 65-A60180-20EG EXT. TOOTH WASHTER 6 X 18 X 2 4 MTG CRT & F. CAB. 65-Z60100-50EG NUT M 6.0 X 1.0 4 MTG CRT & F. CAB. 67-X12668-0E0 SPRING CRT 6MMX40MMX0.5MM 1 67-X34577-0E2 SPRING POWER KNOB 1 55-DE09FC-0CN 21E09 FRONT CABINET 1 56-B192LE-0HC LENS 1 56-DE09FB-0HA PUSH BUTTON 1 56-DE09PK-0HA POWER KNOB 1 T8-DE09SG-PA3 ASS'Y - PACKING '23:R' 1 49-382380-BAT BATTERY 7# (R03P AAA SUM-4) 2 75-DE11LL-CC0 POLYFOAM 1 75-DE11LR-CC0 POLYFOAM 1 75-DE11UL-CC0 POLYFOAM 1 75-DE11UR-CC0 POLYFOAM 1 72-DE09SG-E23 OPERATION MANUAL 1 74-022032-6WE POLYBAG (23CMX34CMX0.06MM) 1 74-120120-80HAA POLYBAG W/SUFFOCATION WARNING 1 76-416010-0AT CARTON BOX 1 T8-21E09G-RC2 ASS'Y - REAR CABINET 1 54-114000-00X FELT TAPE (150MMX19MMX0.3MM) 7 STICK ON REAR CABINET 59-130460-00X RUBBER PAD (25MMX7MM) 2 STICK ON REAR CAB.(FOOTING) 62-314340-0UN FBT SUPPORTER HIPS-KINGFA 113 (VO) 1 62-378080-1UN TRACK 1 62-389620-0UD POWER LINE BLOCK 1 63-B30100-BT4G S/T SCREW B3X10BT 2 MTG SIDE AV BD & REAR CABINET 63-B40200-AB2G S/T SCREW B 4 X 20 AB 6 MTG FRONT & REAR CABINET 63-F30100-BT3G S/T SCREW F 3 X 10 BT 2 MTG RCA JACK & REAR CABINET 63-W30100-AB4G S/T SCREW W 3 X 10 AB 2 MTG SUPPORTER & REAR CABINET 63-W30100-AB4G S/T SCREW W 3 X 10 AB 2 MG M.BD TRACK & REAR CABINET 55-D189RC-8CN 21189REARCABINET 1 58-D106SI-3UI INLAY SIDE AV 1 58-D192RI-8UI INLAY REAR AV 1 58-DE09MP-JKT PLATE MODEL NO. 1 T8-HS36R0-A123 ASS'Y-REMOTE 1 11-0BC337-0BX TRANSISTOR (NPN) BC337-40 1 Q1501 13-00AS12-13B IC AS1213B 1 IC1501 14-IRE05B-XX0 IR EMITTING DIODE TSAL6200 1 D1501 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% 1 R1502 18-CB0229-JNX RES. C.F. 2.2 OHM 1/6W +/-5% 1 R1501 25-HBB479-M1X CAP. ELEC 4.7 UF 10V +/-20% 1 C1504 26-EBP101-JCS CAP. CER 100 PF 50V +/-5% 1 C1501 26-EBP101-JCS CAP. CER 100 PF 50V +/-5% 1 C1502 26-EBP104-ZFS CAP. CER 0.1UF 50V +80%/-20% 1 C1503 40-UOCASR-RMB1XG P.C.B. REMOTE HANDSET BD 1 41-WJ0120-B00 WIRE BARE JUMPER 12MM 1 J1501 45-COS455-KY1 CERAMIC RESONATOR 455KHZ 1 X1501 67-X38064-0E2 BATTERY SPRING (+/-) 1

Page 23

67-X38065-0E2 BATTERY SPRING (+) 1 67-X38066-0E2 BATTERY SPRING (-) 1 74-007026-60C POLYBAG (70MMX260MMX0.06MM) 1 49-HS36R1-00X RUBBER PAD KEYS 1 55-HS36RB-1HA RREMOTEHANDSET-BOTTOMCABINET 1 55-HS36RD-0HA RBATT.DOOR 1 55-HS36RT-1HA RREMOTEHANDSET-FRONTCABINET 1 58-HS36R2-6UI INLAY REMOTE HANDSET 1 T8-HS36R0-PAY ASS'Y - PACKING 1 76-002091-0AT CARTON BOX LWH 624X384X556MM 0.006 76-326350-01A CARTON SHEET 61X37X0.3CM 0.062 V8-T7M123-03E02 SOFTWARE CODE 1 FOR IC001

Page 24

Alignment Procedure

1. FLOWCHART OF ALIGNMENT PROCEDURE

2 Adjustment of B+ voltage

1) Apply 120VAC(±5V) to mains power input, and Philips standard testing pattern to RF input.

2) Adjust VR830 in STANDARD mode until voltage at TP2 (B+) is 108V ±0.5V.

3. RF AGC adjustment Observe monitor the collector waveform of Q101 with the probe of Oscilloscope as illustration below. Select channel 2 (>70dB) from the antenna input. Enter D-mode, select menu6 to adjust RFAGC item until the monitor peak value to 0.8V

p-p

IN60

3Pf

输出

输入

4. Screen & Focus voltage adjustment

Apply pattern signal in normal status, enter D① -mode, press “TV/AV” button to turn

off the vertical output.

Adjust the SCRREEN switch on the flyback transformer to make a horiz② ontal

shining line just visible on the screen.

Turn on the vertical output, adjust the “FOCUS” on the flyback transformer to ③

obtain the optimum focus.

5. White balance adjustment

1)Apply the black and white pattern in normal status;

2)Alignment of normal color temperature

① Change Color Temperature to normal status ② Use a color analyzer to measure the black side of the screen. By changing the

value of RC, GC and BC, set the reading of the color analyzer to X=285, Y=295.

B+ adjustment

AGC Screen & Focus

adjustment

White balance adjustment

Sub-brightness adjustment

Pincushion correction & Horizontal Amplitude adjustment

Center & Amplitude an

OSD adjustment

INPUT OUTPUT

Page 25

③ Use a color analyzer to measure the white side of the screen. By changing the

value of GD, BD, set the reading of the color analyzer to X=285, Y=295.

④ Separately set the brightness and contrast from min. to max., repeat the step 2 and

3 until the reading of the color analyzer is correct.

3)Alignment of warm color temperature

①Change Color Temperature to warm status ②Use a color analyzer to measure the black side of the screen. By changing the value

of RC-W, GC-W and BC-W, set the reading of the color analyzer to X=294, Y=303. ③Use a color analyzer to measure the white side of the screen. By changing the value of GD-W, BD-W set the reading of the color analyzer to X=294, Y=303. ④Separately set the brightness and contrast from min. to max., repeat the step 2 and 3 until the reading of the color analyzer is correct.

4)Alignment of cold color temperature

①Change Color Temperature to cold status ②Use a color analyzer to measure the black side of the screen. By changing the value

of RC-C, GC-C BC-C , set the reading of the color analyzer to X=279, Y=286. ③Use a color analyzer to measure the white side of the screen. By changing the value of GD-C, BD-C, set the reading of the color analyzer to X=279, Y=286. ④Separately set the brightness and contrast from min. to max., repeat the step 2 and 3 until the reading of the color analyzer is correct Note: Provided the production line is equipped with the self- White balance adjusting equipment, white balance of M123A chassis can be adjusted automatically as following: Press “I2C BUS” button under factory mode, the TV set will adjust automatically.

6. Adjustment of Sub-brightness,

① Apply the Grey-scale/Color bar (NTSC signal) to the AV input, in normal status. ② Select BRTC to adjust the sub-brightness, until that the 2nd dark bar of 8 level

Grey scale just can be seen.

7. PAL picture geometric adjustment

menu 3 HPOS6/HPOS5（HZ horizontal center of 60/50 HZ Source） Menu 2 HIGH6/HIGH5(vertical amplitude) VCEN5/VCEN6(position of vertical center) VP60/VP50（vertical position） VLIN6/VLIN5（vertical linearity） VSC6/VSC5（V-S Correction）

8 initialization

press sound-effect under factory mode, the set will initialize, until “OK” appears on the screen which means the initialization is finished. After initialization, the set will quit factory mode automatically.

Page 26

Factory settings

D-mode:

Enter D-Mode by pressing D-Mode ON/OFF key, and then you can enter the D-mode.

S-mode:

Enter S-Mode by pressing VOLUME DOWN key on the unit until the volume decrease to minimum level, then press the DISPLAY key on the remote handset (don’t release the volume key) and you can enter S- mode.

After enter D-mode or S-mode, press OK, then press program up/down to

select menu from menu 1 to menu 22, press OK to enter the menu, press program up/down to select item, press volume up/down to adjust the setting. Press D-mode again to quit factory mode.

You can also enter menu 1 to menu 19 directly by pressing digital button 1~9,

0, notebook, CAP, Display, Sleep, Calendar, System/INS, Favorite, Return, Picture.

Menu 1 (Remote key: “1”)

Item

Remark

R cut-off setting

GC G cut-off setting BC B cut-off setting GD G drive setting BD B drive setting

Menu 2 (Remote key: “2”))

Item

Remark

HIGH5

Height (50Hz)

VP50 Vertical position (50Hz)

VLIN5 Vertical linearity (50Hz)

VSC5 Vertical S correction (50Hz) VBLK5 Vertical blanking start & stop [1C, bit 3 ~ 0] VCEN5 Vertical center (50Hz)

Menu 2 (Remote key: “2”)

Item

Remark

HIGH6

60Hz height

VP60 Vertical position

VLIN6 60Hz Vertical linearity

VSC6 Vertical S correction (60Hz) VBLK6 Vertical blanking start & stop [1CH, bit 3 ~ 0] VCEN6 Vertical center (60Hz)

Menu 3 (Remote key: “3”)

Item

Remark

HPOS5

Horizontal position (50Hz)

Menu 3 (Remote key: “3” )

Item

Remark

HPOS6

Horizontal position (60Hz)

Page 27

Menu 4 (Remote key: “4”)

Item

Remark

CNTX Maximum contrast CNTN Minimum contrast

BRTX Maximum brightness

BRTN Minimum brightness COLX Maximum color COLN Minimum color TNTX Maximum tint level TNTN Minimum tint level

Menu 5(Remote key: “5”)

Item

Remark

BRTC

50% brightness

COLC

50% color

COLP Color level for PAL

SCOL UV gain [06H, bit 6 ~ 4]

SCNT Sub-contrast [06H, bit 3 ~ 0] CNTC 50% contrast

TNTCT 50% tint level (TV mode)

TNTCV 50% tint level (AV mode)

Menu 6(Remote key: “6” )

Item

Remark

ST3

50% Sharpness (TV mode, 3.58 system)

SV3 50% Sharpness (AV mode, 3.58 system) SV4 50% Sharpness (AV mode, other system)

SVD 50% Sharpness (DVD mode) ASSH Asymmetric sharpness [04H, bit 7 ~ 5] SHPX Maximum sharpness SHPN Minimum sharpness

Menu 7( Remote key: “7”)

Item

Remark

Bit 0,Bit 1

under factory mode : 00,11, STD 01:IRC 10:HRC

Bit 2

STD, IRC,HRC 1: user control 0: under factory mode

Bit 3

1: forbid CATV 95/96/97

Bit 4 Bit 5 1: have CCD Bit 6 1:have V-CHIP

MOD1

Bit 7

1:as Monitor no TV mode

Bit 0,Bit 1

Speed of searching

Bit 2

High sensitivity ；1：yes 0:no

Bit 3

Volume control：1:PWM

Bit 4

AV1 :

1：yes 0:no

Bit 5

AV2 :

1：yes 0:no

Bit 6

YUV: 1：yes 0:no

MOD2

Bit 7

Bit 0 Bit 1

MOD3

Bit 2

Page 28

Bit 3 Bit 4 Bit 5

TV，MSP AVL: 1: yes

Bit 6

AV，MSP A VL：1:yes

Bit 7

MONO+SAP：1：yes 0：no

Bit 0 When blue background off (mute pin of CPU): 0: audio

mute on 1: audio mute off

Bit 1 When blue background off (external mute pin of CPU):

0: audio mute on 1: audio mute off

Bit 2 When change channel: 0: picture mute off 1: picture

mute on

Bit 3 Switch between TV and CATV or change channel in the

tune menu 1: picture mute on Bit 4 AFT –MUTE 1: ON, Bit 5 Polarity of Tint Bit 6

OPT

Bit 7 Bit 0 TDA98500 0:no 1:yes Bit 1 MSP34xx 0:no 1:yes

Can’t be set to 1 at

the same time Bit 2 1: AV audio out mute when volume is zero or mute Bit 3 1: decreasing contrast when menu on Bit 4 1: OSD don’t disappear automatically Bit 5 1:biological Bit 6 0: CH LOCK W/O V-CHIP

OPTM1

Bit 7 When turn on 0:child lock off 1:child lock on Bit 0 Bit 1 Bit 2

Power on mode: 00: standby 01:previous

10&11: force power on Bit 3 Hotel mode 1:on 0: off Bit 4 Bit 5

Power on under hotel mode：

00: TV | 01: Video1 | 02: TV2 | 03: Last Bit 6 1: under factory mode turn off the set by the remote or

power off, then turn on or power on, the set enter

factory mode

OPTM2

Bit 7 1: D-MODE

HDCNT

HSTOP

Menu 8 (Remote key: “8” )

Item

Remark

RFAGC

RFAGC [12H, bit 5 ~ 0]

BRTS

Sub brightness for SECAM

OSD

Horizontal position of OSD

OSDF OSD PLL DATA

CCD OSD

Horizontal position of CCD OSD

CCD OSDF PLL DATA of CCD OSD

TXCX

OSD intensity when maximum contrast

RGCN

OSD intensity when minimum contrast

Page 29

Menu 9(Remote key: “9”)

Item

Remark

V01 Volume 1

V25 Volume 25 V50 Volume 50

V100 Volume 100

VOLMAX

Max volume under hotel mode

CURTCEN

Center of the curtain

VOLX

Output gain of PIN28 of TMPA8823 or MSP34x5

PWTM When use PWM to mute and no sound when changing

channel, this item should be minimum as posible

Menu 10(Remote key: “0”)

Item

Remark

Bit 0

TV Color system AUTO：1：yes 0：no

Bit 1

TV Color system NTSC358：1：yes 0：no

Bit 2

TV Color system PALM：1：yes 0：no

Bit 3

TV Color system PALN：1：yes 0：no

Bit 4

AV Color system AUTO：1：yes 0：no

Bit 5

AV Color system NTSC358：1：yes 0：no

Bit 6

AV Color system PALM：1：yes 0：no

MDOE4

Bit 7

AV Color system PALN：1：1：yes 0：no

Bit 0

English: 1：yes 0：no

Bit 1

French: 1：yes 0：no

Bit 2

Portuguese: 1：yes 0：no

Bit 3

Spanish : 1：yes 0：no

Bit 4

AV Color system PAL443：1：1：yes 0：no

Bit 5

AV Color system NTSC443：1：1：yes 0：no

Bit 6

AV AUTO ： 1:AUTO1(PAL443 、 NTSC358 、 NTSC443) 0:AUTO2(NTSC358、PALM、PALN)

MDOE5

Bit 7

Bit 0

1:auto search function of the menu key on the front

panel Bit 1 1: curtain when turn on the set Bit 2 1: curtain when turn off the set

MDOE6

Bit3~ 7

V-mute timing when changing channel(01H = 8ms)

max :248ms

Bit 0 Bit 1

When sound mode change

11:change to the corresponding mode and ODS

display automatically

01: change to the corresponding mode and ODS

doesn’t display

00,10: change to MONO，ODS doesn’t display；

Bit 2 Bit 3

00， 10 ： detect BTSC and Korea stereo

automatically

01：force BTSC 11：force Korea stereo Bit 4

FINE, 1:yes 0：no Bit 5

50Hz block 1:yes 0：no

MDOE7

Bit 6 1: contrast change when power on

Page 30

Bit 7

Bit 0

America V-CHIP standard 1：yes 0：no

Bit 1

Canadian V-CHIP 1：yes 0：no

Bit 2

UNRATED，1：yes 0：no

Bit 3

NO RATING，1：yes 0：no

MDOE8

Bit 4 ~Bit 7

Time setting for curtain when turn on the set

Bit 0 ~Bit 2

N/A

Bit 3

S-VIDEO ,0:parallel to AV1 1: parallel to AV2

Bit 4

1:sound effect w/o mpx (MSP3465)

MDOE9

Bit 5 ~Bit 7

N/A

Menu 12(Remote key: “CAP”)

Item

Remark

OSD2 OSD Horizontal Position

OSDF2 OSD PLL DATA except

PYNX Normal H.SYNC max PYNN Normal H.SYNC min

PYXS Search H.SYNC max PYNS Search H.SYNC min

Menu 13 (Remote key: “Display” )

Item

Remark

CLTM

TV mode

CLVO Video mode

CLVS s-video mode

Bit 2 ~ 0 YDL [15H, bit 2 ~ 0] (-40ns~240ns) Bit 4 ~ 3 NTSC matrix [03H, bit 7 ~ 6] (N1,N2,DVD) Bit 5 C gamma [02H, bit 7] (color gamma on/off) Bit 6 P/N ID [17H, bit 4] (PAL/NTSC killer sensit.) Bit 7 FID [17H, bit 3] (Killer off) Bit 1 ~ 0

ABL gain [16H, bit 5 ~ 4]

Bit 3 ~ 2 ABL start point [16H, bit 7 ~ 6] Bit 4 WPS [00H, bit 7]

ABL

Bit 5 OSD ABCL [16H, bit 3] Bit 1 ~ 0 Black stretch [15H, bit 4 ~ 3] Bit 3 ~ 2 Y gamma [15H, bit 6 ~ 5] Bit 5 ~ 4 OSD level [16H, bit 1 ~ 0]

DCBS

Bit 7 Blank switch [0CH, bit 7]

Bit 0

Over modulation [13H, bit 5]

Bit 1

Aft window size [13H, bit 6]

Bit 2

Buzz reducer [13H, bit 7]

Bit 3 Audio gain switch [14H, bit 7] Bit 4 Bit 5 Bit 6

FLG0

Bit 7

1: VCO adjust automatically when changing channel

Bit 0

CW SW [06H, bit 7], control PIN26,

Bit 1

Slice level [1EH, bit 6]

Bit 2

Mix gain [15H, bit 7]

FLG1

Bit 3

V ramp bias [1DH, bit 4]

Page 31

Bit 4 Bit 5 Bit 6 Bit 7

SLO f0 shift(test only)

Menu 14(Remote key: “sleep)

Item

Remark

HAFC

Bit 1 ~ 0 AFC gain (TV mode) [1CH, bit 5 ~ 4] Bit 3 ~ 2 AFC gain (AV mode) [1CH, bit 5 ~ 4]

AGCC

NOIS

ONTM V-mute timing when power on (01H = 16ms)

NSHP Decreased level of sharpness when noise reduction is on

PVLVL X-ray protection start point (00H Æ 0V & FFH Æ 5V)

PLMT (01H = 8ms)

Menu 15 (Remote key: “Calendar”)

Item

Remark

RC-C

R cut-off setting (for cool color temperature)

GC-C G cut-off setting (for cool color temperature) BC-C B cut-off setting (for cool color temperature) GD-C G drive setting (for cool color temperature) BD-C B drive setting (for cool color temperature)

Menu 16 (Remote key: “System/INS” )

Item

Remark

RC-W

R cut-off setting (for warm color temperature)

GC-W G cut-off setting (for warm color temperature)

BC-W B cut-off setting (for warm color temperature) GD-W G drive setting (for warm color temperature) BD-W B drive setting (for warm color temperature)

YUVGC YUV R cut-off YUVBC YUV B cut-off

Menu 17 (Remote key: “FAV” )

Item

Remark

D-COL

Dynamic color

D-BRI

Dynamic brightess

D-CON

Dynamic contrast

D-SHP

Dynamic sharpness

Menu 18 (Remote key: “Return” )

Item

Remark

S-COL

Standard color

S-BRI

Standard brightess

S-CON

Standard contrast

S-SHP

Standard sharpness

Menu 19 (Remote key: “Picture” )

Page 32

Item

Remark

M-COL

Mild color

M-BRI

Mild brightess

M-CON

Mild contrast

M-SHP

Mild sharpness

Menu 20: no shortcut key

Item

Remark

SEG_POINT1

Highest frequency of VHFL

SEG_POINT2

Highest frequency of VHFH

DATA _VL

VHFL bandswitch（BB）

DATA_VH

VHFH bandswitch（BB）

DATA_UF

UHF bandswitch（BB）

SPE_POS1

The channel number treated specially

SPE_DATA1

Bandswitch in which the special channel （BB）

SENSI_ON SENSI_OFF

Menu 21: no shortcut key

Item

Remark

THEATER-BAS

Theater bass

THEATER-TRE

Theater treble

CONCERT-BAS

Concert bass

CONCERT-TRE

Concert treble

BROCAST-BAS

Brocast bass

BROCAST-TRE

Brocast treble

Menu 22: no shortcut key

Item

Remark

VOL_MAI Volume Loudspeaker GATE

Carrier-Mute

VOL-OUT

AV output gain

AV GAIN

AV input Gain

Note: ① Provided the production line is equipped with the self-adjusting equipment, The adjusted item

should be based on the result by such equipment.

② There’s difference between PAL geometric/OSD adjustment and NTSC geometric/OSD

adjustment. PAL adjustment must be done before NTSC adjustment.

Page 33

24V

R R

U Y Y

SIF OUT

CVBS/Y

E2PROM

24C08

SDA SCL

AMP

TDA7057AQ

MCU+VCD TMPA8823

CRT

Video

amplifie

Horizontal output

Vertical output

STV9302

TUNER

SAWF

+112V

+12

+9V

+5V

4052

AV1 (VIDEO)

AV2 (VIDEO)

MSP3425

AV1 (L,R)

AV2 (L,R)

Page 34

Page 35

Page 36

Page 37

Colour Television Chassis: M123A

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfinding

Fuse Blown

Is the drain of Q801 shorted to earth?

Yes

Cheek / Replace Q801

Is D815~D818 OK?

Yes

Check IC801 and the peripheral components.

Replace D815~D818

Figure 1 Fuse Blown

No raster abnormal + B

Is the + B, resistance to earth ok ?

Check the load of B+

Yes

Check IC802 and their peripheral components

Yes

Check Q830 Q831, Q832

etc.

Figure2 No Raster Abnormal +B

Page 38

Colour Television Chassis: M123A

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfinding

No raster + B Voltage OK

Is the voltage of in 25 of IC201 3.3v

Is the resistance to earth of pin25 if IC201 ok

Yes

Is the H-out waveform at PIN 13 of IC201 OK?

Yes

Check the waveform at static working point of Q401.

Yes

Check Q402 and LOT

Replace IC201

Yes

Replace IC201 Replace Q401

Is the output voltage of IC401 9V?

Check R233,C231 and C233

yes

Figure3 No Raster, +B OK

No picture, dense noise dots

Is the antenna feed line or the adapter broken or unsoldered?

Handing the antenna fault

Yes

Is the signal at Pin41, Pin42 of IC201 ok?

Is the signal at IF pin of the tuner

Is the signal at Pin SCL, SDA of tuner ok?

Check signal at P57, P58, of

IC201 and replace the abnormal relative circuit

Yes

Check EEPROM

Check/Replace I

C20

Is the supply volta

e of tuner

Check/Replace power supply circuit

Yes

Check/Replac e Tuner

Check the relative circuit of Q101, Z101 etc

Figure 4 No Picture dense noise dots

Page 39

Colour Television Chassis: M123A

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfinding

Yes

Symptom: raster ok, no picture, no sound, sparse noise dots

Apply the pointer of multimeter at R X 1 KΩ,

connect one probe to GND, use another to touch P42 of IC101. Are there interference particles flashing on the screen?

Unsolder a pin of C110, apply the pointer of multimeter at R X 1 K Ω , connect the red probe to GND, use the black probe to touch B of Q101. Are there interference particles flashing on the screen?

Yes

Replace the Tuner

Is the voltage at P29, P36 of IC201 ok?

Check and repair the +9V power supply

Bridge a capacitor of 1000pF between the input and output of Z101. Apply the pointer of multimeter at R X 1 K Ω, connect the red probe to GND, and use the black probe to touch B of Q101 Are there interference particles flashing on the screen

Yes

Replace Z101 (SAW)

Does the IF pre-amplifier work normally?

Yes

Check & repair the IF pre-AMP. circuit

Figure 5 Sparse noise dots

Page 40

Colour Television Chassis: M123A

Yes

Is it mute at Pin 1 of IC601?

Yes

No sound

Is the speaker Replace the speaker

Apply the pointer of multimeter at RX1K Ω connect one probe to GND, use another to touch P3, P5 of IC601, Is there interference noise from the speaker.

Check power supply of IC601

Yes

Is the waveform at P47 of IC1001 ok?

Yes

Check/Replace the power supply of IC1001. Then RESET

Is the BUS ok?

Check IC201 and the relative circuit

Check/Replace Q1001, X1002.

Is the waveform at P31 of IC201 ok?

Replace IC201

Yes

Replac e IC601

Check/Replace Q604,Q605.

Figure 6 No Sound

Is both +14V and -14V ok?

Yes

Is the signal at P1 of IC301 ok?

Check/Replace IC301

Check signal at P16 of IC201

Check/Replace IC201,C234

Yes

Check/Replace R244,

R306

Yes

Check/Replace R405, R409

D403, D402

Figure 7 No Vertical Scanning

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfinding

Page 41

Colour Television Chassis: M123A

Check P25, P49 of IC201 and the relative circuit

No Picture

TV&AV haven’t Picture

Check RGB signal

Check +9V, +200V

Check Q501~Q503

Check R516 ~ R521 etc.

Replace IC201

TV has Picture. AV hasn’t Picture.

Check the waveform of pin 14 of IC901

Q905 and its peripheral circuit

Check Pin61 of IC201 and peripheral circuit

Check the logic of Pin9 Pin10 of IC901

Yes

Replace IC901

Yes

AV has Picture. TV hasn’t Picture.

Is the waveform at P30 of IC101 ok?

Check Q208, Q209

and peripheral circuit

Yes

Check IC201 and relative circuit. please reference the previous page named Figure 5.

Figure 8 No Picture

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfindin

Page 42

Colour Television Chassis: M123A

Symptom: Tuning Control doesn’t work

Press STANBY key on R/C. Can the TV be turn on and turn off?

Does the channel number display on the screen?

Yes

Start autosearch. Is the BUS ok?

Yes

After auto-search, Can the searched program be memorized?

Is the voltage at P9 o

IC201ok?

Replace IC201

Yes

Check/Repair +5V power supply.

Is there sync pulse at P62 of IC201?

Check the power supply of IC201. Are there H & V flyback pulses at P12 of IC201

Check R408,R406,D404,C422

Yes

Check/Replace IC201

Check the waveform at Pin57, Pin58 of IC201

Yes

Is the +33V/+5 VA power supply ok?

Check/Repair +33V power supply

Yes

Is there the short circuit around the integration circuit?

Check/Replace the tuner

Check/Repair the integration

Yes

Figure 9 Tuning Control doesn’t work

①

Is there sync pulse at B of Q003?

Replace Q003

Yes

Check Q210, Q211 and the peripheral circuit.

Yes

5. Faultfinding and Test Point with Waveform Diagram

5.1 Faultfinding

Page 43

Colour Television Chassis: M123A

Is there any change on the voltage level at P64 of IC201?

Check the remote control receiver and transmitter.

Yes

Is the VDD(+5V) at P9 and P55 of IC201 ok?

Is there the 8MHz/5Vp-p sine wave oscillations at P6 of IC201?

Is the voltage at P5 of I

C201 ok?

Have P5 of IC201 shorted to GND in an instant. Can the IC201 work?

Check/Repair the reset circuit.

Yes

Check/Replace IC201

Are C021, C022 and X001 ok?

Replace the disabled components

Yes

Check Q002 and peripheral circuit

①

Yes