SAMPI M-60 User Manual

Specifications
M-60 Meter

Liquid Controls M and MA Series rotary motion positive
displacement (PD) meters offer the ultimate in m easu rem ent
accuracy for custody transfer of petroleum products,
aviation fuels, LPG and a broad of industrial liquids.

Superior performance featur es

Low pressu r e dr op – w ill operate on gravity flow or pump

pressure.
Sustained accur acy – no metal-to-metal contact inside the

measuring chamber means minimal wear and deterioration
in accuracy over time, fewer recalibrations and a longer
service life. Meters conform to NIST and International
Weight and Measu res accuracy requirem ent s.

Wide viscosity range – LCE meters can accurately meter
products from less than 30 SSU (1 cP) to 1500000 SSU
(325000 cP).

Maximum adaptability - choice of stock or custom
elbows/fittings provides unequaled mounting flexibility to
meet widely varying installation requirements.

Industries served

LC series M and MA meters
are well-suited for use in
industries requiring precise
flow measurement and
reliable, extended service
life:

• Refined petroleum
products

• Aviation fuels

• LPG

• Agricultural chemicals

• Paints and coatings

• Foods and beverages

• Petrochemicals

• Pharmaceuticals

• Cosmetics

• Printing inks

• Textiles

Accuracy/Performance

Repeatability

Mechanical registration: capable of 0.05% of reading over entire range
Electronic registration: capable of 0.03% of reading over entire range

Linearity

Over 5:1 range
Mech. registration: capable of ±0.125% or better from max nom. flow rate
Elect. registration: capable of ±0.10% or better from max. nom. flow rate

Over 10:1 range
Mech. registration: capable of ±0.22% or better from max. nom. flow rate
Elect. registration: capable of ± 0.10% or better from max. nom. flow rate

Over 40:1 range
Mech. registration: capable of ±0.5% or better from max. nom. flow rate
Elect. registration: capable of ±0.15% or better from max. nom. flow rate

Temperature range

-40° F to 160° F (-40° C to 71° C)

Construction

Meter housing and rotors
Cast aluminum (other
metallurgies, available
including brass, cast-iron
and stainless steel)

Internal components
Aluminum, Ni-Resist,
stainless steel

Seal material
UL recognize component:
Buna-N, Viton, Teflon

Bearings
Carbon, Teflon, Ni-Resist

Dimensions: flow meters w ith electronic registration

Note: Dim ensions sh ow n are not for construction use. C onsult fact ory w hen certified
engineering prints are required.

Model

M-60 4” or 6”

in 13.3 n/a 19.6 21.3 1 .4 7.1 14.2 8.4 9.5

mm 337 n/a 498 540 36 181 359 213 241

Flange

size

Max nom.

Flow rate

2800 l/min
(740 GPM)

G H I J K L M N O

Working
pressure

10,5 bar

(150 PSI)

Net

weight

91,2 kg

(201 lbs)

A B C D E F

in 25.4 16.6 5.6 9.1 n/a 1.5

mm 645 421 143 230 n/a 38

Dimensions

Class Description

Construction and application classes

Dimensions

1 Refined petroleum products Ni-Resist
2 Aviation and jet fuel Ni-Resist

LC series M and MA PD meters are suitable for
metering a broad range of products as listed below.
The appropriate meter class can be used to specify a
desired meter by using the table on the next page of
this publication.

14 Crude oil Ni-Resist
16 General solvents Carbon
30 Herbicides Carbon

Variety of product includes:

3

liquid sugars, sweeteners,

syrups, vegetable oils

Treated waters and solvents

4

where no red metals are

allowed

Acid pH liquids includes: nitric,

8

phosphoric, glacial acetic acids,

citric juices, vinegar

Bearing

Material

Ni-Resist

Carbon

Carbon