Pub. Date 2014.03.20
User Manual
Rev. Date 2014.03.20
Rev. No 0.0
OEM/Integrators Installation Manual
Product Luminaire Controller
Model Name LCRF-STUS
Manufacture SAMJIN LND Co.,Ltd
Ver. V0.0
Document No. Model Name
LCRF-STUS
Page
페이지 1 / 5
User Manual
1.Specification
Description Material / Finish / Data
Pub. Date 2014.03.20
Rev. Date 2014.03.20
Rev. No 0.0
Model No.
Encloser
Size / Weight
RF Sensing
Network Method
Operating Temp(℃)
Operating Humidity(℃)
LCRF-STUS Luminaire Control Board
non
62.5x 45.5 / 0.03Kg
Wall Controller / Radius 25M
RF 900MHz
-10(min) ~25(typical)~45(max)
-10(min) ~90(max)
2.Operation
1) A device which is connected to an SMPS and modulates color temperature and
brightness of luminaires by receiving the signal from Wall Controller.
Document No. Model Name
LCRF-STUS
Page
페이지 2 / 5
Pub. Date 2014.03.20
User Manual
Rev. Date 2014.03.20
Rev. No 0.0
3.Installation
1) located in the junction box of the lum ina ire, and connects the antenna and the
SMPS for integrated installation.
No Description Detail(Function)
1
2
3
.
Antenna 917.1MHz~923.3MHz Antenna
LCRF-STUS LCRF-STUS Board Construct
SMPS SMPS to LCRF-STUS Connect
Document No. Model Name
LCRF-STUS
Page
페이지 3 / 5
Pub. Date 2014.03.20
User Manual
Federal Communication Commission Interference Statement
Rev. Date 2014.03.20
Rev. No 0.0
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. Information to user:
The user manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
USERS MANUAL OF THE END PRODUCT:
In the user manual of the end product, the end user has to be informed to keep at least 20
cm separation with the antenna while this end product is installed and operated. The end
user has to be informed that the FCC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment. If the size of the end product is smaller than 8x10cm,
then additional FCC part 15.19 statement is required to be available in the users manual:
Document No. Model Name
LCRF-STUS
Page
페이지 4 / 5
Pub. Date 2014.03.20
User Manual
Rev. Date 2014.03.20
Rev. No 0.0
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains FCC ID:
TSW-LCRFSTUS ". If the size of the end product is larger than 8 x 10 cm, then the following
FCC part 15.19 statement has to also be available on the label: This device complies with
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The RF module limited to OEM installation ONLY:
The OEM integrator is responsible for the compliance to all the rules that apply to the
product into which this certified RF module is integrated.
This device is intended only for OEM integrators under the following
conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and
users, and The transmitter module may not be co-located with any other transmitter or
antenna. As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations
or collocation with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
Document No. Model Name
LCRF-STUS
Page
페이지 5 / 5
Loading...