SAM JIN IM6001 MPP01 User Manual

Multipurpose Sensor QSG

Front

Setup

Back

Multipurpose Sensor

Placement

The Multipurpose Sensor can monitor whether doors, windows, and cabinets are open or closed.

Simply place the two parts of the Multipurpose Sensor on door and door frame, making sure that the magnet alignment marks are next to each other.

The Multipurpose Sensor can also monitor temperature.

Make sure the Multipurpose Sensor

is within 15 feet (4.5 meters) of your SmartThings Hub or SmartThings Wiﬁ (or compatible device with SmartThings Hub functionality) during setup.

Use the SmartThings mobile app to

select the “Add device” card and then select the “Multipurpose sensor” category.

Troubleshooting

Hold the “Connect” button with a

paperclip or similar tool for 5 seconds, and release it when the LED starts blinking red.

Use the SmartThings mobile app to

select “Add device” card and then follow the on-screen instructions to complete setup.

Remove the tab on the Multipurpose

Sensor marked “Remove When Connecting” and follow the on-screen instructions in the SmartThings app to complete setup.

Connect button

If you’re still having trouble connecting the Multipurpose Sensor, please visit Support.SmartThings.com for assistance.

Safety Instructions

• Read, keep, and follow these instructions. Heed all warnings.

• The SmartThings Water Leak Sensor is water-resistant but not water-proof; avoid submerging it in water or liquid to keep interior dry and to protect batteries. All other SmartThings products should not be used near water or exposed to dripping or splashing of any water or liquid.

• Clean only with a dry cloth.

• Do not install near any heat sources such as radiators, heat registers,

•

• Read our Product Usage Guidelines at:

www.SmartThings.com/Guidelines.

Safety Instructions: Hub

Disconnect the network cable and power adapter or any other connected peripherals if any of the following conditions exist:

• The power cord or connector is damaged or frayed.

• You want to clean the Hub (see Important Safety Instructions).

• excessive moisture.

• The Hub power adapter is damaged or has been dropped and you suspect it needs to be serviced.

Avoid installing the SmartThings Hub near or inside sources of metal, radio or electromagnetic interference.

WARNING: No user-serviceable parts inside. Refer all

IMPORTANT CONSUMER INFORMATION: Please read before activating or using the device.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Disclaimer

Some content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal non-commercial use.

You may not use any content or services in a manner that has not been authorised by the content owner or service provider. Without limiting the foregoing, unless expressly authorised by the applicable content owner or service provider, you may not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or distribute in any manner or medium any content or services displayed through this device.

Tested to Comply With FCC Standards FOR HOME OR OFFICE USE

Multipurpose Sensor

Manufacturer Model : IM6001-MPP01 FCC ID : 2AF4S-IM6001-MPP01 IC : 20753-IM6001MPP01

Motion Sensor

Manufacturer Model : IM6001-MTP01 FCC ID : 2AF4S-IM6001-MTP01 IC : 20753-IM6001MTP01

Button

Manufacturer Model : IM6001-BTP01 FCC ID : 2AF4S-IM6001-BTP01 IC : 20753-IM6001BTP01

Water Leak Sensor

Manufacturer Model : IM6001-WLP01 FCC ID : 2AF4S-IM6001-WLP01 IC : 20753-IM6001WLP01

Outlet

Manufacturer Model : IM6001-OTP01 FCC ID : 2AF4S-IM6001-OTP01 IC : 20753-IM6001OTP01

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Caution

responsible for compliance could void the user’s authority to operate this equipment.

Important Note: FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Canada Statement

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada

+ 1 hidden pages