sames
SINGLE PHASE POWER/ENERGY ADAPTOR WITH
FEATURES
SA9122APA APPLICATION NOTE
PA9122AP
64 SEGMENT LCD AND SERIAL INTERFACE
n Enables the demonstration of the
SA9122APA device using a
PM9103AP module
n Pulse rate selectable via jumper leads
DESCRIPTION
The PA9122AP demonstration adaptor connects into the PM9103AP metering module.
In this configuration the PA9122AP allows evaluation of the SA9122EPA device.
It is recommended that this Application Note be read in conjunction with the PM9103AP
Application Note.
The PA9122AP adaptor comes complete with an LCD, the SA9122EPA device as well
as demonstration software.
n Operates over a wide temperature range
n Protected against ESD
n Meets the accuracy requirements for
Class 1 AC Watt hour meters
7191 PDS038-SA9122-001 Rev. A 28-01-97
1/6
PA9122AP
BLOCK DIAGRAM
NEUTRAL
IN
NEUTRAL
OUT
NEUTRAL
LIV E
SHUNT
PO W ER
SU PPL Y
SA9122E
. . . . . . .
J7
DR-01311
FOU T2
FOU T1
RX
.. ... ....
J1
J2
OPTO
COUPLER
OPTO
COUPLER
CONNECTION DESCRIPTION
Jumper 1 allows for the selection of the pulse rate to monitor: fp or fp/290.
The LCD on the PA9122APA adaptor may be configured as:
Eight digit - seven segment with tariff icons (default)
or
Five digit - seven segment with extended icons.
Designation Setting Description
D-SUB
CONNE C-
TION
J1 Lower to middle FOUT1
Upper to middle FOUT2
J2 Lower to middle Pin 36
Upper to middle Pin 33 (Default)
J3 Lower to middle Pin 1
Upper to middle Pin 4 (Default)
J4 Lower to middle Pin 22
Upper to middle Pin 35 (Default)
J5 Lower to middle Pin 21
Upper to middle Pin 34 (Default)
J6 Lower to middle Pin 15
Upper to middle Pin 2 (Default)
J7 Lower to middle Pin 16
Upper to middle Pin 3 (Default)
2/6
sames
PA9122AP
The location of the extended icons on the LCD layout are shown in Fig. 1 below.
Figure 1: LCD Layout
8.41
4.0
4.5
3.5
7.5
1.9
1.4
t1
t2
2.13
t3
8.0 Max.
4.27
14.0 M in. Viewing Area
4.5
t4
4.3
7.5
1.0
Max.
T1Coso
T2To tal
T3Com
T4Cost
3.4
7.18
4.6
a
f
b
.
.
.3. ... .
g
e
c
d
1h
16.45
17 x 2.54 = 43.18±0.1
2.54±0.05
21
T2
T1
1.6
4.6
2.54±0.05
REAR POLARIZER(Re flective)
REAR GLASS
4
5 6
..
T3 T4
12.3
60.0 ±0.8
27.6
..
1.5
FRONT POLARIZER
FRONT GLASS
1.5
TOT A L
5.0
8.41
kWrh
kWsh
Wh/imp
2.4
1.95
2
.
~
~
~
~
3
2
0
~
±
~
1
0
.
3
2
8.3
4-R1.0
%Error
7
. .8.
imp/kW h
Hz
k1
8h
k2
.
10.0±2.0
2
.
0
±
5
.
3.1
2
6
.
0
±
6
.
0
16.8
6
.
0
±
6
.
0
0.25±0.05
2
.
0
1.1±0.1
±
5
.
2
2.8
Max.
0.2
a
1
f
b
.
.
g
0.8
7.8
e
c
0.65
d
0.5
4. 0°
DE TAI L OF DIGI T (1 ~ 8)
1.0
Max .
DR-00902
58.0
1.0
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
COM1 t1 1a 2a 3a 4a 5a 6a 7a 8a ~2 ~1
COM1
COM2 t2 1b 2b 3b 4b 5b 6b 7b 8b r h COM2
COM3 t3 1c 2c 3c 4 c 5c 6c 7c 8c V A
COM4 t4 1h 2h 3h 4h 5h 6h 7h 8h s h
Pin 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
COM1 ~3
%Error 8f 7f 6f 5f 4f 3f 2f 1f Cos
COM2 Hz imp/KWh 8g 7g 6g 5g 4g 3g 2g 1g Total
COM3 COM3 k1 k2 8e 7e 6e 5e 4e 3e 2e 1e Com
COM4 COM4 W WH/IMP Total 8d T4 7d T3 6d T2 5d T1 4d 3d 2d 1d Cost
NOTES:
1. DRIVE: 1/4 DUTY, 1/3 BIAS, 5.0 VOP
2. OPERATING TEMP: -20°C TO +80°C
3. VIEWING DIRECTION: 6 O'CLOCK
4. SEGEMENT TOLERANCE: ± 0.05
5. GENERAL TOLERANCE: ±0.2
Ø
sames
3/6
PA9122AP
FUNCTIONAL DESCRIPTION
1. Interface Board
The PA9122AP adaptor (see Fig. 2) allows for the connection of a SA9122EPA
DIP-40 device, to an evaluation board of type PM9103AP. This module inserts into
the dual-in-line socket of the PM9103AP module, in the same orientation as the
SA9103 XPA DIP-20 device is inserted.
Figure 2: PM9122AP LAYOUT
D R-01313
2. Connection Details
The connection details for the PA9122AP adaptor, to connect to the PM9103AP
module, are shown in Fig. 3.
3. Demonstration Software
Software which runs under Windows 3.1 or Windows 95, is provided with each
evaluation adaptor.
4/6
sames
Figure 3: PA9122AP adapter Interface to PM9103AP module
PA9122AP
LC D
19
U8
20
21
22
U6 U7 U9
23
24
25
26
27
28
29
30
31
32
33
34
35
36
U5 U4
18
17
im p /k W h
W h /im p
Hz 32 1
kWsh
% E rro r
16
.. .. .... ...
15
14
Tot al
13
12
11
10
T3T2 T4
9
8
7
6
T1
5
. ....
4
3
2
1
T2 TOTAL
T3 COM
T4 COST
T1 COST
920n
R[3]
R[1]
R[2]
S[ 15]
S[ 14]
S[ 13]
S[ 12]
S[ 11]
S[ 10]
S[7]
S[8]
S[9]
S[6]
S[0]
S[5]
S[1]
S[2]
S[3]
S[4]
U1
DD
V
RX
R[0]
FOU T2
FOU T1
ss
v
SA9122A1
CPIP
CPIN
CPOP
CIP
CIN
COP
VREF
GND
IN V
IIP
IIN
CON
CPON
OSC O
OSC I
U2
ORDERING INFORMATION
Part Number Description
PA9122AP 3 X 230V, 3 X 80A Module
sames
IV P
GND
IIN
CIOP
CION
VREF
CVON
IIP
SS
SIN
V
CIIP
CIIN
CVIN
CVIP
CVOP
V
DD
SOUT
NC
OSC 1
OSS2
DR -01314
5/6
PA9122AP
Disclaimer: The information contained in this document is confidential and proprietary to South African Micro-
Electronic Systems (Pty) Ltd ("SAMES") and may not be copied or disclosed to a third party, in whole or in part,
without the express written consent of SAMES. The information contained herein is current as of the date of
publication; however, delivery of this document shall not under any circumstances create any implication that the
information contained herein is correct as of any time subsequent to such date. SAMES does not undertake to inform
any recipient of this document of any changes in the information contained herein, and SAMES expressly reserves
the right to make changes in such information, without notification,even if such changes would render information
contained herein inaccurate or incomplete. SAMES makes no representation or warranty that any circuit designed
by reference to the information contained herein, will function without errors and as intended by the designer.
Any sales or technical questions may be posted to our e-mail adress below:
energy@sames.co.za
For the latest updates on datasheets, please visit our web site:
http://www.sames.co.za
South African Micro-Electronic Systems (Pty) Ltd
P O Box 15888, 33 Eland Street,
Lynn East, Koedoespoort Industrial Area,
0039 Pretoria,
Republic of South Africa, Republic of South Africa
Tel: 012 333-6021 Tel: Int +27 12 333-6021
Fax: 012 333-8071 Fax: Int +27 12 333-8071
6/6
sames
Loading...