Combo Heart Rate Strap
Bluetooth® Smart & 5 kHz Transmission
USER MANUAL
Your Combo Heart Rate Strap offers a comfortable
fit and wireless connectivity to receiving devices
like cardio equipment and smartphones.
The Bluetooth® Smart transmission technology
connects with smartphones and other Bluetooth
Smart Ready (Bluetooth 4.0) devices. Your heart
rate will be transmitted directly from the strap to
the phone when the Combo HR Strap is worn.
The Combo HR Strap also transmits heart rate
data using the standard 5 kHz signal that is
compatible with most cardio equipment. The
5 kHz heart rate signal is also transmitted when
the strap is worn.
1
Combo HR Strap Components
1. The electrode sensors read your heart rate
signal.
2. The heart rate transmitter sends your heart
rate signal to the receiving device.
Combo Heart Rate Strap
FRONT
Strap
BACK
Electrode Electrode
Transmitter
Adjustment
2
Wearing Your Combo HR Strap
1. Connect the transmitter to the strap.
FRONT
2. Moisten the electrode sensors with water.
BACK
3
Electrode Electrode
Wearing Your Heart Rate Strap
3. Unhook and secure the strap around your
chest just below your chest muscles.
4. Adjust the strap for a snug yet comfortable fit.
5. Make sure the electrode sensors are firmly
against your skin and the logo on the
transmitter is facing out and upright.
FRONT
logo facing out
and upright
4
Pairing Your Combo HR Strap
Your Combo HR Strap will work with compatible
watches and cardio equipment using 5 kHz
transmission. No pairing is required for
5 kHz transmissions.
Your Combo HR Strap is also compatible with
Bluetooth Smart Ready (Bluetooth 4.0) receiving
devices such as a smartphone with a Bluetooth
Smart compatible app installed.
If using a receiving device such as a smartphone,
you will need to pair it with your Combo HR Strap
upon first use. Please refer to your app or phone
manual for instructions on how to operate its
Bluetooth capabilities.
5
Care & Maintenance
Transmitter: After each use, remove the
transmitter from the strap and towel dry. Clean
with mild soap and water whenever needed. Do
not use alcohol or abrasive material to clean.
Strap: After each use, rinse with water and hang
dry. Clean with mild soap and water whenever
needed. Do not iron or dry clean the strap.
Do not bend the electrode sensors sharply.
!
Do not use a washing machine or dryer to
!
clean your transmitter or strap.
Do not store when the electrode sensors
!
are wet. If wet, the Combo HR Strap can be
activated and lead to shorter battery life.
6
Replacing the Battery
Your Combo HR Strap uses one (1) standard
lithium battery: CR2032
1. On the back side of the transmitter, insert a
coin into the slot of the battery cover and turn
counterclockwise to open.
2. Insert a new battery with the positive (+)
side facing up against the battery cover.
Make sure the rubber seal ring is in place to
ensure water resistance.
3. Relace the battery cover and use the coin to
turn it clockwise to close.
7
Water Resistant
Your Combo HR Strap is water resistant. However,
heart rate readings will not be read if submerged
in water (e.g., swimming).
Specifications
Water resistance: 1 ATM
Operating temperature: 23°F - 122°F
(-5°C - 50°C)
Radio frequency: 2.4 GHz BLE/Bluetooth smart
protocol
Wireless compatibility: 5 kHz transmission;
Bluetooth Smart Ready (Bluetooth 4.0)
smartphones
8
Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located
or operating in conjunction with any other antenna or
transmitter.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment
IC: This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe Best conforme à la
norme NMB-003 du Canada.
9
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
DECLARATION DE CONFORMITE D’INDUSTRIE CANADA
Ce périphérique a été testé et reconnu conforme auxlimites
spécifiées dans RSS-210.
Son utilisation est soumise aux deux conditions suivantes:
(1) il ne doit pas provoquer d’interférences gênantes et
(2) il doit tolérer les interférences re.ues, notamment
cellessusceptibles d’en perturber le fonctionnement.
10
Loading...