SALUS North America SS912ZB User Manual

!"#$%&'()(

(

*'$+,--,+%&'./0%12(3+,#+(40%5"6(3-%7(8&&#.9%'5&:(3"'$&#(;33<=>?@A(

Visit www.salusinc.com for the User Manual

In#the#Box#

###

#

Tools#Needed#

#

Note:#

(

(

( (

(

(

(

B55%+%&',-( "C0%D7"'+( 7,E( F"( #"C0%#"5(
50"(+&( F0%-5%'G(1&'$+#01+%&'(&#( 7,+"#%,-$H(
&#( &+I"#( #,5%&( %'+"#J"#"'1"( +I,+( 7,E(
#"501"(+I"(#,5%&(#,'G"K(

3"'$&#(:%+I(F,++"#E(

;=L(MN>H()!(O%+I%07A((

P,G'"+(

P&0'+%'G(Q%+(

*'$+,--,+%&'.(

/0%12R$+,#+(40%5"(

(

S=(TI%--%D$(31#":5#%U"#(

(

(

(((((

(

(

PAIRING#INSTRUCTIONS#

• Follow your system’s instructions to prepare to add devices to the system.

• Remove the face plate from the Sensor and pull the battery tab to start

the pairing process.

• When the Sensor is detected and added to the system, proceed to the
Sensor installation.

INSTALLATION#INSTRUCTION#

• Identify the location for the Sensor and Magnet, orienting the flat end of
the Sensor and Magnet parallel to each other as shown, and the
Magnet on the right side (side with indicator). The preferred location

for the Sensor is on the door or window casing on the handle side of
the door or window, with the Magnet on the door or window as close as
possible to the Sensor. Proper installation may require mounting the
Sensor and Magnet inverted or rotated from the orientation shown.

• Position the Sensor at the desired location and screw into position
using the screws provided. If screws are not appropriate, use the included
adhesive pad by first removing the brown backing of the adhesive pad
and attaching it to the Sensor bottom. Make sure to properly align the
tamper switch opening. Then remove the white/red paper tape and press
the Sensor to the desired location. (For UL installations, the unit must
be mounted with screws.)

• Open the Magnet case, position the Magnet at the desired location and
attach to the door or window with the screws, replacing the Magnet cover
when done. If screws are not appropriate, use the adhesive pad by first
removing the brown backing and attaching it to the Magnet bottom. Then
remove the white/red paper tape and press the Magnet to the desired
location. (For UL installations, the unit must be mounted with screws.)
Depending on the depth of the door or window in the frame, the included
spacer may be required to raise the Magnet above the surface of the door or
window. Use the longer screws to attach the Magnet with the spacer.

• Open and close the door to verify that the Sensor is working properly, and
the Sensor or Magnet does not interfere with the opening and closing of the
door.

REPLACING#THE#BATTERY#

;V$"(&'-E(80#,1"--(8ORMN>H(N,E&U,1(NORMN>H(W'"#G%X"#(WO=MN>H(&#(4T(@,++"#%"$(4TMN>(F,++"#%"$A

• Slide the Sensor face plate up and lift it from the Sensor body.

• Press a finger on the positive end of the battery and lift to remove the battery

from the Sensor.

• Insert a new battery into the Sensor, observing the proper polarity.

• Position the Sensor face plate over the Sensor body and slide the face plate onto

the Body.

FACTORY#RESETTING#THE#SENSOR#

• Remove the face plate from the Sensor.

• Remove the battery.

• Press and hold the tamper switch while re-inserting the battery.

• Release the tamper switch when the LED lights on the front of the Sensor. The

Sensor is reset to factory defaults and will respond to pairing requests.

• After pairing, replace the face plate on the Sensor.

LED#INDICATIONS#

Solid at power up:

Initializing, checking for Factory Reset

3 flashes then pause:

Searching for network to join

(

SPECIFICATIONS

Operating
Conditions

32–104°F / 0–40°C
20–90% relative humidity
(non-condensing)

Storage

-4–185 °F / -20–85°C
20–95% relative humidity
(non-condensing)

Protocols
Supported

ZigBee 3.0
RF Freq.

2.4 GHz

Battery

3V Lithium CR2

Max. Gap

1.0” / 25.4 mm

Size

Sensor:

2.87” x 0.79” x 0.79” /
73 x 20 x 20 mm
Magnet:

1.57” x 0.39” x 0.39” /
40 x 10 x 10 mm

FCC#STATEMENTS#

WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.

NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and

•

receiver.

Connect the e

•

from

• Consult the dealer or an experienced radio/TV technician
for help.

quipment into an outlet on a circuit different

that to which the receiver is connected.

FCC#AND#INDUSTRY#CANADA#

RF Radiation Exposure statement: This equipment complies
with FCC and Industry Canada RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20
centimeters between the antenna and all persons.

INDUSTRY#CANADA#

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.

The distance between user and products should be no less than 20cm
la distance entre l'utilisateur et les produits devraient être au moins 20 cm

SALUS#WARRANTY#

SALUS North America, Inc. (“Salus”) warrants that for a period of five (5)
years (“Warranty Period”) from the date of purchase by the consumer
(“Customer”), this device, excluding batteries (“Product”), shall be free of
defects in materials and workmanship under normal use and service in
accordance with all supplied instructions. During the warranty period,
Salus shall, at its option, repair or replace any defective Products, at no
charge for the device. Any replacement and/or repaired devices are
warranted for the remainder of the original Warranty Period or ninety
(90) days, whichever is longer.

This warranty does not cover removal or reinstallation costs. This
warranty does not apply to any Product (i) which has been modified,
repaired, or altered, except by Salus or an authorized Salus
representative, (ii) which has not been maintained in accordance with any
handling or operating instructions supplied by Salus, or (iii) which has
been subjected to unusual physical or electrical stress, misuses, abuse,
negligence or accidents.

This warranty is the only express warranty Salus makes for the Product.
Any implied warranties, including warranties of merchantability or fitness
for a particular purpose, are limited to the Warranty Period or the
shortest period allowed by law.

SALUS SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, or limitation on the
duration of implied warranties of merchantability or fitness, so these
exclusions or limitations may not apply to you.

No oral or written information or advice given by Salus or a Salus­authorized representative shall modify or extend this warranty. If any
term is held to be illegal or unenforceable, the legality or enforceability
of the remaining terms shall not be affected or impaired.

Customer’s sole and exclusive remedy under this limited warranty is
product repair or replacement as provided herein. If a Product under
warranty is defective, the Customer may:

• contact the party (“Seller”) from which the Customer purchased the
Product to obtain an equivalent replacement product after the
Seller has determined that the Product is defective and the
Customer is eligible for a replacement, or

• contact Salus Service at [e-mail], to determine
whether the device qualifies for a replacement. If a replacement is
warranted and is shipped prior to the return of the device under
warranty, a credit card is required and a hold may be placed on the
Customer’s credit card for the value of the replacement until the
returned device is verified as eligible for replacement, in which case,
the Customer’s credit card will not be charged.

This warranty gives you specific legal rights, and you may also have other
rights that vary from jurisdiction to jurisdiction. If you have any questions
regarding this warranty, please write Salus at:

SALUS North America, Inc.
850 Main Street
Redwood City, CA 94063

!"#$%&'()(