Page 1
Digital Thermostat
Models: VS30W and VS30B
INSTALLER / USER MANUAL
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 2
02 VS30W and VS30B Installer Manual
Contents
VS30
1 x Installer / User manual
4x AAA Batteries
Digital Thermostat
Models: VS30W and VS30B
INSTALLER / USER MANUAL
Fixing screws
Contents
Box Contents
Introduction
Product Compliance
Installation
User Guide
Parameter Settings
Installers Notes
Warranty
Box Contents
Icons used in this manual:
Safety
Important info
Your benet
For latest PDF installation
guide please go to
www.salus-controls.com
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 3
Product Compliance & Safety Information
INTRODUCTION
Thank you for purchasing the room thermostat
VS30. The VS30 is a 230V digital thermostat
which oers simple temperature control of your
heating system.
By purchasing the VS30 you have decided on a
digital room thermostat which allows you to
adjust surface heating appliances individually,
such as underoor, wall or panel heating.
A clear energy saving is possible by reducing
temp.
Product Compliance
This product is CE compliant and meets the
following EC Directives Electro-Magnetic
Compatibility Directive 2004/108/EC
Low voltage Directive 2006/95/EC
Safety Information
Use in accordance with the regulations.
The VS30 is to be used for room
control of hot water heating systems
inside the house.
Installation
This product must be tted by a competent
person, and installation must comply with the
guidance, standards and regulations applicable
to the city, country or state where the product
is installed. Failure to comply with the
requirements of the relevant guidance,
standards and regulations could lead to injury,
death or prosecution.
Always isolate the AC mains supply
before installing or working on any components
that require 230V AC 50Hz supply.
We hope you enjoy this product...
VS30W and VS30B Installer Manual 03
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 4
Product Compliance & Safety Information
Sources of danger
The thermostat must be disconnected from mains
supply before removing the cover.
230V AC
Emergency
Switch o the voltage to the indivdual thermostat
wring centre or complete system.
Installer parameter settings
The VS30 is equipped
with installer parameter section.
This must only be entered
by the installer or competent
person. Changing these parameters
can have a serious eect on
your heating system. See page 41.
For the installer
Please enter any parameter
changes in the installer notes section.
04 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 5
Installation – Terminal Connections
Understanding your terminal connections
Rear of VS30
Power Terminals 230 Vac
Used for supplying power to the
unit and switched output.
NSB (Night Set Back) Connection
Used for a 230V output to other
thermostat. See page 8.
Sensor Terminals (Optional)
Can be used for external AIR
or Floor sensor.
1
3
3 2 1
2
VS30W and VS30B Installer Manual 05
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 6
Installation – Thermostat Mounting
1
3
2
60mm
Wall Mounting
For wall mounting, mark and
mount the rear case to the wall.
The VS30 is suitable for wall boxes
with a centre hole distance of : 60mm
Gently remove front housing.
06 VS30W and VS30B Installer Manual
Gently remove front housing.
Only for ush
mounting boxes
with horizontal
xing holes.
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 7
Installation – Thermostat Mounting
Not to be positioned on an exterior wall.
130cm
Mounting position and installation
To ensure trouble free operation and ecient control, the VS30 room thermostat is best positioned
in a draft free area, and at 130cm from the oor. Do not position the thermostat near any heat
source, behind curtains, direct sunlight or an area of high humidity.
VS30W and VS30B Installer Manual 07
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 8
08 VS30W and VS30B Installer Manual
S2
S1
NSB
SL
L
N
S2
S1
NSB
SL
L
N
Sensor Terminal (optional)
Sensor Terminal (optional)
Night set back output
Load (Thermal Actuators)
Live 230V AC 50Hz
Neutral
L N
Wiring Centre
Thermal
Actuator
Optional SALUS
Sensor
Installation – Terminal Connections
L N
NSB for other
thermostats
Output
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 9
Installation – Terminal Connections
Power Terminals
NSB (Night Set Back) Connection
Sensor Terminals (if applicable)
You are ready to secure the rear housing to the wall box
Check that the wiring is completed for:
1
2
3
Please use the screws provided
Ensure the orientation arrow
is pointing upwards.
VS30W and VS30B Installer Manual 09
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:38
Page 10
Installation – Thermostat Mounting
1
Fit the front housing to the rear housing
Align the front housing
at the top edge.
2
Lightly press until you
hear a positive click.
Ensure the pin connections are aligned
10 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 11
Installation – LCD Graphics
1
2 3 4 5 6 7
8
9
11
12
14
13
10
16
15
VS30W and VS30B Installer Manual 11
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 12
ICON FUNCTION
BOX means to select the mode
e.g. means the current setpoint is Hi temp, means the Hi temp is not selected.
Sunny: Hi comfortable temperature.
Cloudy: Middle comfortable temperature.
Moon: Low comfortable temperature.
Programmable thermostat Program mode indicator: Indicates program is running,
Auto On or Auto O. For group thermostat this indicates that it is a member of a group.
Party indicator:
When Party mode is active.
Vacation indicator:
When Vacation mode is active.
Frost protection indicator:
Frost protection is active, not available in cooling mode (if applicable).
Installation – LCD Graphics
1
2
3
4
5
6
7
12 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 13
Installation – LCD Graphics
ICON FUNCTION
Heat indicator:
Indicates heat is required.
Cool mode indicator:
Indicates cooling is required (if applicable).
Temperature indicator:
Display the room temperature.
Display the set-temp.
Also used to show the other information.
Temporary manual override indicator:
If the set temperature is changed when in program mode,
the hand will appear until the next program start time.
Programs number indicator:
In AUTO program mode or Temporary override is running,
it means the current program running.
Day indication:
1 = Monday.
8
9
10
11
12
13
VS30W and VS30B Installer Manual 13
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 14
Installation – User Interface
ICON FUNCTION
Floor sensor probe indicator:
Show only when Air + Floor sensor is connected.
Setting indicator:
Indicates the unit is in setting mode when program setting.
Indicate’s the manual mode.
Keylock indicator:
Shows that keys are inactive.
14
15
16
14 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 15
Installation – User Interface
KEY FUNCTION
1. Increase or decrease setpoint temperature.
2. Increase or decrease Day, Clock, Timer, Party and Holiday.
3. Select installer parameter value.
1. Mode selection.
2. Long press to return to home display without saving.
3. Short press to return to the previous screen when it is in user/installer setting mode.
1. OK key: Short press to conrm selection.
2. Long press to save and exit.
3. Long press to enter the user settings.
Lock/Unlock.
Enter Installer parameter settings.
Test mode.
OR
+
++
5 SECONDS
5 SECONDS
5 SECONDS
+
OR
VS30W and VS30B Installer Manual 15
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 16
Installation – First Power Up
16 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 17
Installation - Graphics Key
Press once
Press x amount of times
Hold for ve seconds
Flashing
xx
Short press to save and
long press to save and exit
Short press to back up
ON rst power up.
Proceed to page 19
VS30W and VS30B Installer Manual 17
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 18
User Guide - Setting time and date
18 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 19
User Guide - Setting time and date
Use left to select 12
hour and right to
select 24 hour.
Adjust the time
using the up or
down arrow key.
Hour
Minutes
VS30W and VS30B Installer Manual 19
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 20
User Guide – Understanding Temperature Levels - Heating
Highest Temperature typically used for
early morning and early evening.
Typically 20 Deg C
Mid Temperature typically used for times of
day when you are active around the home.
Typically 19 Deg C
Lower Temperature typically used for
unoccupied or sleep times.
Typically 17 Deg C for UFH or 15 Deg C for radiators
Frost Temperature typically used for
periods of long absence or holidays.
Typically 5 Deg
Your thermostat comes preset for the above temperatures.
These can be adjusted. Please see page 37.
20 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 21
User Guide - Understanding Temperature Levels - Cooling
Occupied Temperature. Typically 22ºC
Unoccupied Temperature Typically 40ºC
This avoids cooling being active when the property is unoccupied.
Evening Temperature Typically 26ºC
Your thermostat comes preset for the above temperatures.
These can be adjusted. Please see page 37.
See device setting D18, section on page 44
VS30W and VS30B Installer Manual 21
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 22
User Guide - Default Heating Schedule .1
21
19
17
12.00 6.00 9.00 16.00 23.00
Monday to Friday
21
19
17
12.00 7.00 23.00
Saturday to Sunday
22 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 23
User Guide - Optional Heating Schedule .2
21
19
17
12.00 6.00 22.30
Monday to Friday
21
19
17
12.00 7.00 23.00
Saturday to Sunday
VS30W and VS30B Installer Manual 23
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 24
User Guide - Optional Heating Schedule .3
21
19
17
12.00 5.00 8.00 14.00 22.00
Monday to Friday
21
19
17
12.00 7.30 22.30
Saturday to Sunday
24 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 25
User Guide - Optional Heating Schedule .4
21
19
17
12.00 6.00 9.00 15.00 22.30
Monday to Friday
21
19
17
12.00 7.30 23.00
Saturday to Sunday
VS30W and VS30B Installer Manual 25
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 26
User Guide - Optional Heating Schedule .5
21
19
17
12.00 6.00 10.00 16.00 23.00
Monday to Friday
21
19
17
12.00 7.30 23.30
Saturday to Sunday
26 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 27
User Guide - Default Cooling Schedule .1
22
40
26
12.00 6.00 9.00 16.00 23.00
Monday to Friday
22
40
26
12.00 7.00 23.00
Saturday to Sunday
VS30W and VS30B Installer Manual 27
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 28
User Guide - Optional Cooling Schedule .2
22
40
24
12.00 6.00 22.30
Monday to Friday
22
40
24
12.00 7.00 23.00
Saturday to Sunday
28 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 29
User Guide - Optional Cooling Schedule .3
22
40
24
12.00 5.00 8.00 14.00 22.00
Monday to Friday
22
40
24
12.00 7.30 22.30
Saturday to Sunday
VS30W and VS30B Installer Manual 29
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 30
User Guide - Optional Cooling Schedule .4
22
40
24
12.00 6.00 9.00 15.00 22.30
Monday to Friday
22
40
24
12.00 7.30 23.00
Saturday to Sunday
30 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 31
User Guide - Optional Cooling Schedule .5
22
40
24
12.00 6.00 10.00 16.00 23.00
Monday to Friday
22
40
24
12.00 7.30 23.30
Saturday to Sunday
VS30W and VS30B Installer Manual 31
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:39
Page 32
SYSTEM
User Guide – Setting the Temperature Schedule
Use right and left to
select the day of the
programs.
5/2
7 Days
Individual
32 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 33
User Guide – Setting the Temperature Schedule
Adjust the time
using the up or
down arrow key.
Use right and left to
select the Hi/Mid or
low temp.
VS30W and VS30B Installer Manual 33
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 34
User Guide – Setting the Temperature Schedule
When you set the temperature, the schedule will respond
to those temperatures. See page 37 on how to change
Repeat through to program 4.
If you require a 5th or 6th program enter a time
and select your temperature
To remove a program out set the time to --:--.
34 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 35
User Guide - Temporary Override
Use the up or down
arrow key to view
your program set
temperature.
Use the up or down
arrow key to adjust
the temperature to
the setting you
desire.
Temporary override allows you to increase the temperature or decrease
it to the desired setting until it reverts back on the next program time.
VS30W and VS30B Installer Manual 35
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 36
User Guide - Temporary Override
To cancel temporary override press or
See below.
Conrm the
temporary set
temperature.
36 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 37
User Guide - Permanent Override
To cancel permanent override select
See below.
Move from
to
Use the up or down
arrow key to view
your set temperature.
See page 35.
To adjust your
permanent override
temperature follow
the steps on page 35.
Repeat for if required
Setting permanent low temperature
VS30W and VS30B Installer Manual 37
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 38
User Guide - Party Mode
The party mode is an
option that enables
temperature
for a period of time.
You select up to 9hr
50min.
Use the right
arrow to select
the party mode.
Use the up
arrow to select
the hr/min.
Press tick to
conrm and
it will start to
count down .
38 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 39
User Guide - Holiday Mode
Use the right arrow
to select the holiday
mode.
Use the up arrow to
select how many
days to be o for.
Press tick to conrm
and it will start the
holiday count down.
VS30W and VS30B Installer Manual 39
USER GUIDE
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 40
User Guide - Frost Protection
Use the right arrow
to select the frost
mode.
Use the up arrow to
select the frost
protection
temperature.
Press tick to conrm
the temperature
that it has been
set to.
40 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:40
Page 41
Installation - Entering Device Menu
If you need to
change device
parameters follow
the steps below.
Must only be
entered by the
installer.
This is the rst
screen of the
device menu.
Press all three
buttons
simultaneously.
VS30W and VS30B Installer Manual 41
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 42
Installation - Device Parameters
DX FUNCTION SYSTEM SETTING DEFINITION DEFAULT
D01 Heating 0 Pulse Width Modulation
Control 1 On-O 0.5 Deg C +/- 0.25 Deg C 0
2 On-O 1.0 Deg C +/- 0.5 Deg C
D02 Room -3.0 to 3.0 Temperature Oset from
Temperature Deg C Measured Temperature to 0 Deg C
Oset Compensate for any error
D03 Sensor probe or 0 Sensor stat not Connected
Cylinder thermostat 1 Sensor stat Connected 0
connection
D04 Sensor probe 0 D03 must be set to 1 then
used as air sensor external sensor be used as
or oor sensor Air sensor. There will be no
internal temp measurement
0
1 D03 must be set to 1 then
external sensor used for oor
protection. Internal temp is
measured by stat
D05 Cooling Control 1 On-O 0.5 Deg C +/- 0.25 Deg C
2
2 On-O 1.0 Deg C +/- 0.5 Deg C
D06 Actuator type 0 NO Normally Open
1
1 NC Normally Closed
D07 Valve protection 0 Disable
1
1 Enable
42 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 43
Installation - Device Parameters continued
DX FUNCTION SYSTEM SETTING DEFINITION DEFAULT
D08 Frost Set point 5-17 Deg C Required Temperature for frost 5 Deg
Temperature protection and holiday mode
D09 Hour Format 0 12
1
124
D10 N/A N/A N/A N/A
D11 Daylight Saving 0 OFF
1
Time (DST) 1 ON
D12 Heating Set point
5-35 Deg C
Maximum temp that can
35 Deg C
Limit be set for heating
D13 Cooling Set point
5-40 Deg C
Maximum temp that can
5 Deg C
Limit be set for Cooling
D14 Floor sensor High Output relay will be switched o
Limit Temperature 6-45 Deg C when temp is reached for 27 Deg C
oor protection
D15 Floor sensor Low Output relay will be switched on
Limit Temperature 6-45 Deg C when temp is reached for 10 Deg C
oor protection
D16 Floor sensor Limit Output relay will be switched o
for cooling 6-45 Deg C when temp is reached for 6 Deg C
oor protection
VS30W and VS30B Installer Manual 43
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 44
Installation - Device Parameters continued
DX FUNCTION SYSTEM SETTING DEFINITION DEFAULT
D17
D18
Preset program
selection
1-5 Select 1-5 of the default programs 1
Heat/Cool mode
selection
0 or 1
0: heating mode
1: cooling mode
0
44 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 45
Installation - Technical Detail
Model VS30W/ VS30B
Type Electronic programmable room thermostat, digital room
thermostat designed for 230V AC applications
Programming Modes User selectable for 5/2, ALL and Individual day options
Program Number 1-6 Selectable
Modes Party, Vacation, Program and Frost
NSB 230V Output from external clock
Override Permanent and temporary
Frost Protection 5ºC Adjustable
Power Source 230V AC 50Hz
Rating 3 Amp
Temperature Scale 5 to 35ºC, tolerance 0.5ºC
Heat/Cool Global changeover using communication bus and external
input to the wiring centre
Sensor Air or oor protection.
Device Parameters See page 42 for full list of functions
Operating Temperature 0 to 50ºC
Storage Temperature -20 to 60ºC
VS30W and VS30B Installer Manual 45
INSTALLATION
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 46
Installation - Notes
46 VS30W and VS30B Installer Manual
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 47
SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall
perform in accordance with its specication, for a period of ve years from the date of installation. SALUS Controls
sole liability for breach of this warranty will be (at its option) to repair or replace the defective product.
Customer Name: .............................................................................................................................
Customer Address: ..........................................................................................................................
............................................................................... Post Code: ........................................................
Tel No: ........................................................ Email: .........................................................................
Engineers Company: .......................................................................................................................
Tel No: ......................................................... Email: ........................................................................
Installation Date: ..............................................................................................................................
Engineers Name: ............................................................................................................................
Engineers Signature: .......................................................................................................................
Warranty
VS30W and VS30B Installer Manual 47
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Page 48
www.salus-controls.com
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road,
Dodworth, Barnsley S75 3SP, UK.
SALES: T: +44 0 1226 323961
E: sales@salus-tech.com
TECHNICAL: T: +44 0 1226 323961
E: tech@salus-tech.com
Issue Date: April 2014
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to
change specication, design and materials of products listed in this brochure without prior notice.
SALUS Controls is a member of the Computime Group
00086/2
iT600 VS30W - VS30B Installer - User Manual 014_Layout 1 16/07/2014 14:41
Loading...