Salus VS10WRF, VS10BR, VS20BRF Installer's/user's Manual

4 in 1 Digital Thermostat RF

Models: VS20WRF and VS20BRF

VS10WRF and VS10BRF

INSTALLER / USER MANUAL

Product Compliance

This product complies with the essential requirements and other relevant provisions of Directives
2014/30/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at
the following internet address: www.saluslegal.com.

Safety Information

Use in accordance with the regulations.

Indoor use only.
Keep your device completely dry.
Disconnect your device before cleaning it with a dry cloth.

Introduction

Thank you for purchasing the SALUS 4 in 1 room thermostat it must be used with the Universal Gateway
UGE600 (purchased separately) when having an Internet connection or with the KL08RF for the underfloor
system withoul Internet connection. The Universal Gateway allows communication with other devices in
the iT600 RF system range. Other Zigbee devices include wiring centre, system receiver & TRV. You can
use your iT600 system with the Salus Smart HomeApp. Available on Google Play and App Store.

Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

RX10RF (optional for an underfloor

system, mandatory for a TRV system)

TRV10RFM

TRV10RF

KL10RF

KL08RF

Installation – Terminal Connections VS10WRF

Understanding your terminal connections

Rear of unit

Power Terminals 230 Vac

Used for supplying power to
the unit. 230V supply can be
sourced from the wiring centre
or any convenient source.

Sensor Terminals

Can be used for external AIR,
Floor sensor when configured
as thermostat. Can also be used
for Cylinder thermostat when
configured for HW.

1

2

1

2

Pairing with Wiring Center (KL08RF) with Internet connection

6

8

10

7

9

11

5 sec

SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK.

Sales: T: [phone]

E: [e-mail]

Technical: T: [phone]

E: [e-mail]

www.salus-controls.com

SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development, SALUS Controls plc
reserves the right to change specification, design and materials of products listed in
this brochure without prior notice.

12

Installation – First Power Up

The following screens show examples only

MCU software version

will be shown

ZIGBEE software version

will be shown

Please make sure that your Universal Gateway is installed. You can use it with both internet and non internet connection.
The LED will be blue when connected to the internet and red when it’s not connected.

With Internet

Without Internet

*Please note that 88.8 and

8.8 are a reference to the
software version.

If you are installing an underfloor system without an Internet connection, you can use the coordinator from the
KL08RF instead of the Universal Gateway.

Pairing with Wiring Center (KL08RF) with Internet connection

3

1

2

Pairing with Wiring Center (KL08RF) without Internet connection

OR

5 sec

1

2

Pairing the TRV with Internet connection

31 2

4

5

Tap Scan for equipment when you
want to start adding equipment
to the App. The gateway will start
flashing red.

3

5

4

6

7

OR

5 sec

5 sec

5

Tap Scan for equipment when you
want to start adding equipment
to the App. The gateway will start
flashing red.

4

CO10RF

6

7

Press and hold the for
10 seconds until the TRV starts
flashing red.

Wait until the LED is solid red.
Press the Open/Close button
once. When the initialization
process is complete, the LED will
go off.

8 9

10

11

12

Installation – Power Up your devices

Please follow the installation procedure for all equipment. After installation, your devices should look like this:

Please follow the on screen instruction in order to complete the pairing process.

If the pre-configured program is not suitable for your application,
hold down the bottom three keys for a short time, until the display shows SEL PROG.

Installation – System Parameters

Selecting unit type

Use or
to select the type of unit.
After selection has been
made, press to
confirm.

Programmable Thermostat

Digital Thermostat

Hot water timer

Installation – Check the paired devices

Tap the tile from the
Dashboard.

If you want to see what devices are connected to your Universal Gateway you can know exactly by using
the Identify procedure.

Tap the name of your
device.

Tap the Identify
button. Your device
will start flashing.

Factory reset

If you have made an error or need to change your system parameters please follow steps below.
This should only be done by your installer.

Press all three buttons

simultaneously

Now you are ready to set up your system as desired.

Press the button again
after identifying your
devices.

Use right and left to select

the day of the programs.

Use right and left to select

the day of the programs.

5/2

Individual

7 Days

5 sec

3 sec

Pairing the TRV without Internet connection

5 sec

Press and hold the for 10
seconds until the TRV starts flashing
red.

Wait until the LED is solid red.
Press the Open/Close button once.
When the initialization process is
complete, the LED will go off.

The pre fix number on the TRV will

change as the TRV(s) pair.

Once all TRV’s have paired press

If you use the maximum number of
TRVs it will automatically take you to the
Mainscreen.

5 sec

Setting the time

Pairing the Receiver RX10RF without Internet connection

Follow the System Parameters instructions and set your Receiver on RX1.

5 sec

5 sec

OR

5 sec

5 sec

OR

Set the program / schedule.

3

1

2

5

Tap Scan for equipment when you
want to start adding equipment
to the App. The gateway will start
flashing red.

4

Pairing the Receiver RX10RF with Internet connection