Salus miniSmartPlug User Manual

! Version!2!

Installation/User!Guide:!miniSmartPlug!(SX885ZB!!!!!!!)!

IN THE BOX

!

NOTE:

SAFETY INSTRUCTION

Read these instructions carefully before installing and using the miniSmartPlug and keep this guide
in a safe place for future reference.

• Verify compatibility with your associated connected home system before installation.

• Follow all instructions provided by your connected home manufacturer regarding the addition

of devices to your connected home system. An authorized, qualified installer may be required.

Salus accepts no responsibility for damage caused by not following these instructions.

!

!

Additional equipment may be
required due to building
construction or materials, or
other radio interference that
may reduce the radio range.

!

miniSmartPlug!

Installation/User!Guide!

!

!

PRODUCT INTRODUCTION

The Salus miniSmartPlug switch is a ZigBee compatible,
connected AC switch that provides ON/OFF control of the
attached AC appliance and measures the power/energy
consumption of the appliance. Key features include:

• Quick and easy installation

• Support for OpenHome and ZigBee™ HA connected home

systems

• Support for loads up to 15Amps (resistive).

• Appliance load sensing to turn ON.

CONTROLS AND INDICATORS

Item

Description

Plug

NEMA 5-15 (Type B) plug. Compatible with US
and Canadian standard 120VAC/15A electrical
outlets

Socket

NEMA 5-15 grounded (Type B) outlet.
Compatible with US/Canadian standard
120VAC/15A electrical plugs

Multi
Button

Multi-function user input button:
Pair, Rejoin, Factory Defaults, and On/Off

LED

White LED status indicator

PAIRING INSTRUCTIONS

• Prepare to add devices per your system’s instructions.

• Plug the miniSmartPlug switch into the desired AC outlet to

account for any radio interference

• When the switch is detected, follow your system’s
instructions to finish adding the switch to the system. You
may need to press the Multi Button to identify the switch.

USING THE SWITCH

Note: Immediately after being plugged in, there is a slight
delay before the miniSmartPlug switch starts measuring
energy and responding to the button or remote commands.

TURN OFF/ON

• To toggle the miniSmartPlug switch (turn ON when OFF, or
turn OFF when ON), press the Multi Button.

RESET TO FACTORY DEFAULTS

• To reset the switch to factory default settings, press the
Multi Button while plugging in the switch and release the
button when the LED comes on.

FORCE REJOIN TO CURRENT NETWORK

• To find a better path to the connected home system if the
network is intermittent and/or other ZigBee devices are
added/deleted, press the Multi Button 5 times quickly (less
than ½ sec between presses).

LOAD SENSING OF APPLIANCE ON/OFF SWITCH

• When the miniSmartPlug switch is OFF, the on/off switch of
certain appliances can be used to turn ON the
miniSmartPlug switch. Note: Turning OFF the miniSmartPlug
switch using the appliance switch is not supported.

• To turn ON the miniSmartPlug switch, start with the
appliance switch in the on position. Turn the appliance
switch off for about ½ sec, then back on. The miniSmartPlug
switch will turn ON when it detects the brief off period.

Note: Certain appliances, such as some CCFL lamps and
electronic equipment using wall transformers, cannot be

monitored as their electrical characteristics do not change
enough when the appliance on/off switch is changed.

LED INDICATIONS

ON for 2 - 4 sec., then OFF

Switch power up, Switch is OFF

3 flashes

Searching for network to join

Steady ON

Switch is ON

Steady OFF

Switch is OFF

ON, flash OFF every 2 sec

Switch is ON, no network

OFF, flash ON every 2 sec

Switch is OFF, no network

TROUBLESHOOTING

WILL NOT PAIR INITIALLY

• Radio interference is present at the desired location.

1) Relocate the ZigBee receiver,

2) Select a different location for the switch, or

3) Add a ZigBee repeater to the system.

LOSS OF CONNECTION AFTER PAIRING

• Make sure ZigBee receiver is operating

• Radio environment may have changed:

1) Force rejoin to possibly find a better radio path or

2) Apply radio interference solutions above.

APPLIANCE DOESN’T TURN ON WHEN LED ON THE SWITCH IS ON

• Make sure the attached appliance is turned ON.

• Make sure the appliance can be controlled via the AC

supply. Appliances with “soft” on/off buttons cannot be
turned on by turning the AC supply ON.

SWITCH DOESN’T TURN ON WHEN APPLIANCE SWITCH IS TURNED OFF

THEN BACK ON

• Make sure the appliance is working by plugging the
appliance into an outlet and using the on/off switch.

• Make sure the appliance on/off switch starts in on state.

• Make sure the appliance on/off switch can be monitored,

e.g., switch is not behind a transformer or a “soft” switch,
CCFL can be monitored, etc.

Plug

Socket

LED

Multi Button

BB"
DG"
DR"

LG"
MN"

! Version!2!

SPECIFICATIONS

Operating
Conditions

32 - 104°F / 0 - 40°C
10 - 90% humidity
(non-condensing)

Storage

-4 – 185 °F / -20 – 85°C

Protocols
Supported

ZigBee HA 1.2 + basic Meter
RF Freq.

2.4 GHz

Input

120VAC +/-10%, 60 Hz

Max. Switch
Current

15 Amp resistive

Size

Including Plug:

2.13” x 1.46” x 2.32” /
54mm x 37mm x 59mm
Not including plug:

2.13” x 1.46” x 1.49” /
54mm x 37mm x 38mm

FCC STATEMENTS

WARNING: Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for
help.

FCC AND INDUSTRY CANADA

RF Radiation Exposure statement: This equipment complies

with FCC and Industry Canada RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters
between the antenna and all persons.

INDUSTRY CANADA

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

SALUS WARRANTY

SALUS North America, Inc. (“Salus”) warrants that for a period of two (2)
years (“Warranty Period”) from the date of purchase by the consumer
(“Customer”), this device, excluding batteries (“Product”), shall be free of
defects in materials and workmanship under normal use and service in
accordance with all supplied instructions. During the warranty period,
Salus shall, at its option, repair or replace any defective Products, at no
charge for the device. Any replacement and/or repaired devices are
warranted for the remainder of the original Warranty Period or ninety
(90) days, whichever is longer.

This warranty does not cover removal or reinstallation costs. This
warranty does not apply to any Product (i) which has been modified,
repaired, or altered, except by Salus or an authorized Salus
representative, (ii) which has not been maintained in accordance with any
handling or operating instructions supplied by Salus, or (iii) which has
been subjected to unusual physical or electrical stress, misuses, abuse,
negligence or accidents.

This warranty is the only express warranty Salus makes for the Product.
Any implied warranties, including warranties of merchantability or fitness
for a particular purpose, are limited to the Warranty Period or the
shortest period allowed by law.

SALUS SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, or limitation on the
duration of implied warranties of merchantability or fitness, so these
exclusions or limitations may not apply to you.

No oral or written information or advice given by Salus or a Salus­authorized representative shall modify or extend this warranty. If any
term is held to be illegal or unenforceable, the legality or enforceability of
the remaining terms shall not be affected or impaired.

Customer’s sole and exclusive remedy under this limited warranty is
product repair or replacement as provided herein. If a Product under
warranty is defective, the Customer may:

• contact the party (“Seller”) from which the Customer purchased the
Product to obtain an equivalent replacement product after the
Seller has determined that the Product is defective and the
Customer is eligible for a replacement, or

• contact Salus Service at [e-mail], to determine whether
the device qualifies for a replacement. If a replacement is warranted
and is shipped prior to the return of the device under warranty, a
credit card is required and a hold may be placed on the Customer’s
credit card for the value of the replacement until the returned
device is verified as eligible for replacement, in which case, the
Customer’s credit card will not be charged.

This warranty gives you specific legal rights, and you may also have other
rights that vary from jurisdiction to jurisdiction. If you have any questions
regarding this warranty, please write Salus at:

SALUS North America, Inc.
850 Main Street
Redwood City, CA 94063