Salus FC600-M Instruction Manual

M

L

FC600

+

−

AIR

+

−

AIR

+ −

L

N

Introduction

Terminals description

Electrical diagram

DIN rail mounting

Display description and button functions

Product Compliance

Control module for FC600 thermostat
Model: FC600-M 0-10V

Safety Information

Principle of operation

The FC600-M 0-10V module is dedicated to fan coils or trench heaters con­trolled by 0 ... 10V signal. It is a supplement to the main thermostat SALUS
FC600. The module smoothly adjust fan speed via controling 0V...10V
voltage. In addition, device can control two electric actuators (heating
and cooling valve).

This product complies with essential requirements of the European
Parliament Directive And Of The Council 2012/19 / EU of 4 July 2012 on
waste electrical and electronic equipment (WEEE).

230V AC

2-PIPE SYSTEM

4-PIPE SYSTEM

OR

Power supply unit (PSU)

230V AC / 24V DC

1. Double-digit, 7-segment LED display

- displays parameters: F1, F1, F3, t and voltage and time values

2. Entering the menu, selecting the parameter, increasing the value

3. Conrmation of parameter selection, reduce the value

Use in accordance with national and local regulations of the country and
in EU territory.

Indoor use only. Keep your equipment completely dry.

The installation must be carried out by a qualied person in accordance
with the rules of the country and in the EU.

Before install, repair, maintenance or during any connection work
disconnect power supply from the module and make sure the terminals
and wires are free of voltage.

The electrical installation where module works should be secured with
a fuse, specially selected to the applied loads.

The device can not be used with the damaged case.

Under no circumstances dont’t modify the module construction.

Do not allow access to the module to people who didn’t read this manual.

Do not install the device under voltage.

A short circuit at the output may damage the unit.

It is forbidden to operate a defective device or repaired by unauthorized
service.

For module covering there is a special installation enclosure for the
installation of electrical equipment. This enclosure should prevent user
before access to the module wiring terminals. The module is designed to
be mounted on a standard 35mm DIN rail. Before sliding the module .
onto the DIN rail , slide the hook using the at sc rewdriver. When
module is mounted on the rail, place the hooks at the original position.
Make sure that module is mounted solidly and that it can not be removed
from the rail without a tool.

NOTE: The connection wires should be protected against tearing,
loosening, or built up in such a way that they can not be exposed to
mechanical stress.

The module recognizes input signals from SALUS FC600 for three dierent
voltage fan levels and accordingly sets the 0V...10V output voltage.

Voltage values for each levels and time of voltage incrase on output are
settable by buttons and displayed on LCD. Settings are saved to the device
memory. The module smoothly changes the voltage value at startup and
during switching between fan speed mode.

Additionally this module recognizes the input signals for the heating valve
and a cooling valve. Accordingly which signal will be received, module will
send +24V voltage at the output for the heating/cooling valve.

Terminal

Name

Function

Module power supply 24V DC

Heating valve control output

Cooling valve control output

Power supply and fan control 24V DC

F1

Fan Speed control (Low level) - 230V AC input

F2

Fan Speed control (Medium level) - 230V AC input

F3

Fan Speed control (High level) - 230V AC input

V1

4 pipe: 230V AC control input - heating valve

2 pipe: 230V AC control input - heating / cooling valve

V2

4 pipe: 230V AC control input - cooling valve

2 pipe: N/A

N

Neutral

1

1

2

3

2

3

1

3

2

Instructions Manual

www.salus-controls.eu

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls plc reserve
the right to change specification, design and materials of products listed in this brochure
without prior notice.

Issue Date: VII 2017

Distributor of SALUS Controls:

QL CONTROLS Sp. z o.o., Sp. k.
Rolna 4
43-262 Kobielice,
Poland
[e-mail]

NOTE: Before opening the casing disconnect the power supply from
the terminals of FC600-M 0-10V module and FC600 controller.

NOTE: In the module should be used porcelain, slow blow 5x20 mm fuses
with nominal burnout current of 8A / 230V.

Display will ashes
voltage value for the selected
program. Set the target value

by using button or .

On display will ashes time value.

Set the target value using

button or .

The voltage threshold settings are limited by the module:

Time of voltage increase at the output when module starts-up and
switches voltage tresholds is expressed by the parameter t. This parameter
is limited to the range from 0 to 50 s.

The module provides a smooth voltage increase at the output for
thresholds depending on t parameter, according to the following
characteristic.

A fuse is located inside the device casing.
It protects module and the devices connected to it.

To open the casing of the module, you need to pry all the hooks
(with a at screwdriver) and then carefully remove its upper part.

Using a at screwdriver, pry the fuse holder, replace the fuse, put the
holder back in place and then snap the upper housing of the module.

The total voltage value for the F1-F3 thresholds is limited to 0 ... 10V range.

Setting voltage thresholds for fan speed Replacing the fuseSetting the increase/decrease time of the output

voltage

1

1

2

3

3

4

4

2

Press button to enter menu

Press button

to enter menu.

Press button to
conrm your option.

Press button to
conrm your option.

Wait 8 seconds

- the module will
save settings.

Wait 8 seconds

- the module will
save settings.

After saving device

will automatically

return to the menu.

After saving device

will automatically

return to the menu.

After 15 seconds

inactivity, the module

will go into sleep

mode.

After 15 seconds

inactivity, the module

will go into sleep

mode.

Using button select the appropriate parameter to set:

Select the t parameter
by using button.

F1 - for the rst voltage threshold
F2 - for the second voltage threshold
F3 - for the third voltage threshold

NOTE: Module starts to supply voltage at the output when any threshold

is selected. The current value change causes a fan speed change - this
allows you to check its operation and select adequate speed.

F1 - range from 0V to setpoint in F2
F2 - range from the setpoint in F1 to the setpoint in F3
F3 - range from setpoint in F2 to 10V

5

5

6

6

7

7

0V

50

t

10V

1

s

s

{

{

{

F1

F2

F3

SELECT

SELECT

SET

SELECT

SET

max.

min.

5x20

FUSE

0V

50

t

10V

1

s

s

{

{

{

F1

F2

F3

SELECT

SELECT

SET

F1 F2 F3 t

SELECT

SET

SELECT

SET

SELECT

SET

F1 F2 F3 t

0,1V

MENU

MENU

ZAPIS

8s

max.

min.

5x20

FUSE

Product Specication

Power supply 24V DC

Max current consumption 8A

Input voltage signals 230V AC

Output signals:

-

-

- fan

1(1)A, 24V DC
1(1)A, 24V DC
6,5(6,5)A, 24V DC

Fan control 0…10V

Mounting type DIN rail 35mm

Protection degree IP20 (build over)

Operating temperature from -10°C to 40°C

Storage temperature from -10°C to 65°C

Relative humidity

5-85% without steam
condensation

Display

Double-digit,
7-segment LED display

Wires gauge 0,5 - 2,5 mm

2

Lenght of uninsulated wire 7 mm

Weight 60 g

Standards

PN-EN 60730-2-1
PN-EN 60730-1

Protection class II

Overvoltage class II

Pollution degree 2

Dimensions [mm] 65 x 90 x 52

65 mm

48,5 mm

45 mm