Salus EP110 Installation Manual

Model: EP110

Single channel programmable controller

Installation Manual

Contents

Product Compliance ................................................................................................. 3

Safety Information ...................................................................................................... 3

Box content .................................................................................................................... 3

Introduction ................................................................................................................... 4

Features ............................................................................................................................. 4

Installation ....................................................................................................................... 5

Button functions and LCD icons ........................................................................ 7

Operations ....................................................................................................................... 8

Functions ......................................................................................................................... 14

Factory Reset ................................................................................................................. 16

Technical Info ................................................................................................................ 17

Warranty ........................................................................................................................... 18

02 EP110 Installation Manual

Product compliance

Installation

Jumper Settings

Input: 230V, 50Hz
Output: 3A/ switch terminal

1

EP110 Volt Free application only

EP110 - 230V Application Only

Note: Please remove red link wire for this application.

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Not Used

2 Not Used

3 Volt Free Connection

4 Volt Free Connection

Earth Parking
(no electrical connection)

NL1234

NL123456

Changes to the jumpers settings should only be made by the Engineer carrying
out the installation or other qualified person. The installer should select the jumper
positions required if changes need to be made to the factory default settings.
These jumpers are found on the rear of the controller.

EP110/ EP210/ EP310 Switching Bridges

Switch

Program

5-2 days programme or

24h programme

Fully pumped system(P*)

or gravity-fed hot water

system(G*)

System

Feature EP110/310 Settings

5-2

24H

24H

5-2

NA

NA

P

G

EP210 Settings

EP110/EP310 EP210

This product complies with the essential requirements and other relevant provisions of the following EU
Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please check www.saluslegal.com for the full information.

Safety Information

Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely
dry. This product must be installed by a competent person and in accordance with all the EU and national
regulations.

Always isolate the AC Mains supply before installing or working on any components that
require 230 VAC 50Hz supply.

Box content

The box includes the EP110 controller, 2X screws and plugs and the Quick Guide installation manual.

EP110 Controller 2x screws and plugs

Model: EP110/EP210/EP310

Installer Manual-Quick Guide

Quick Guide Installation

EP110 Installation Manual 03

Introduction

A programmable heating controller is used to switch the heating system and/or hot water in your home as
needed. It works by controlling the heating boiler according to a series of programmed settings that take effect
at different times of the day. The controller can be set up to 3 programs per day, with complementary Boost
actions and can operate in five different modes. Three different sets of time can be set for each day of week,
resulting in a total of 21 settings applicable to the device.

When connected to a system with a non-programmable (digital) thermostat, it can switch off/on the boiler
and control the heating and/or hot water in your system in a programmed manner. You can use the controller
in a fully pumped and controlled system, where heating and hot water can be operated independently or in
gravity-fed water system, where the central heating cannot be operated without hot water.

The heating system will not work if the programmer has switched it off. The controller does not detect the
temperature or adjust the heating mode in your house, it just tells the boiler when to switch Off/On depending
on our individual time settings.

With the controller you don’t have to worry about switching On/Off your system manually. All you need to do
it so set up the schedules that fit your needs. The controller can be used on your system to control either the
central heating OR the hot water.

Features

• Single Channel Programmer for Central Heater or Hot Water

• 12 or 24 hour clock format

• 5+2 or 24 h individual program with 3 settings per day

• Boost function

• Holiday function

• Advance function

• Memory backup

04 EP110 Installation Manual

Installation

NL123456

NL123456

Wiring and terminal description

230 VAC

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 NC (Output)

2 Not Used

NL1234

3 Switch Live (Output)

4 230V Common (via Link)

Earth Parking
(no electrical connection)

Volt free application. Note: Please remove red link wire (like the one in the picture above) for this application.

Volt Free

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Not Used

2 Not Used

3 Volt Free Connection

4 Volt Free Connection

Earth Parking
(no electrical connection)

NL1234

EP110 Installation Manual 05

Wall mounting

Fix the backplate to the wall.

Align the front housing

at the top edge.

Jumper settings

The jumpers are found on the rear of your controller and can be used
to change the settings for the program type or internal backup memory
battery. If you want to change the position of your jumpers, please note
that you will need to reset your device. The default position for the jumpers
set a 5+2 program type and keep the internal backup battery off.

EP110 Switching Bridges

Fit the front housing. Press lightly.

Switch Feature Setting Default

Program 5-2 days program or

Memory Backup Disable/enable the

Note: Changes to the jumper settings should only be made by the engineer carrying out the installation
or another qualified person. The installer should select the jumper positions required if changes need to
be made to the factory default settings. These jumpers are found on the rear of the controller.

06 EP110 Installation Manual

24h program

internal backup

battery

5-2 24H 5-2 days program

OFF ON Internal backup

battery disabled

Button functions and LCD icons

MODE

<

<

SELECT SET

Key Function

Mode Press to select ON/ONCE/AUTO/

ADV/OFF.

+1Hr Press to enter/cancel Boost override

function by setting Boost hours.

Select Press to select the setting of clock/

date/week day, etc.

Set Press to confirm the setting.

+Hr

Up arrow Press to increase clock/day, press and

hold to enter fast advance.

Down arrow Press to decrease clock/day, press

and hold to enter fast advance.
Press to activate backlight.

Hardware reset

Press and hold button for 3 seconds
to activate Holiday mode.

Select + Set Press and hold buttons to enter clock

setting mode.

1

2

3

4

1

Showing when relay is On

2

Boost hours

3

Daylight Saving Time On/Off

4

Program number

5

ON Mode Active
(controller runs continually)

5 6

12

11

10

7 8 9

7

Auto Mode Active (controller runs in Auto)

ADV Mode Active

8

(controller runs in advance override)

9

OFF Mode Active (controller is off)

10

AM/PM

Holiday mode on

11

6

ONCE Mode Active
(controller runs for 1 period a day)

Days of the week

12

EP110 Installation Manual 07

Operations

Initial power up

After power up or after RESET is pressed, the programmer is reset to factory default settings. During system
reset, all LCD icons and segments are turned on for 2 seconds and all keys are blocked. After 2 seconds and all
keys are released, the programmer is initialized. First the software version is shown and after that the typical
reset display is shown. The time should be 12:00am.

MODE

+Hr

<

<

SELECT SET

MODE

<

Default settings

Function Status after Reset

Operation Mode Normal mode

Clock 12:00 AM

AM/PM indicator AM

<

SELECT SET

MODE

+Hr

<

<

SELECT SET

+Hr

Date January 1, 2016

Daylight Saving Time(DST) On

Program Factory default 5+2

Program Number indicator Off

SET indicator Off

PROG indicator Off

Mode indicator(s) “Off“

Output Relay Off

CH/HW indicator(s) Off

08 EP110 Installation Manual

Setting time and date

The first thing you will have to do is to set the time and date on your controller. First you will need to set up
the time and then the date. To enter clock setting mode, press and hold Select and Set buttons for 3 seconds.
Please follow the instructions below.

MODE

<

<

SELECT SET

3 sec

Press and hold the

indicated buttons
together for 3 sec.

MODE

<

<

SELECT SET

Press Up or Down to set

the hour. Press Select

to confirm.

+Hr

MODE

<

<

SELECT SET

Choose your clock format

Press Up/Down arrow for

12/24 hr format.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to set

the minutes. Press Select

to confirm.

+Hr

MODE

24

<

<

SELECT SET

Choose your clock format
Press Up/Down arrow for

12/24 hr format.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to

set the year.

Press Select to confirm.

+Hr

+Hr

MODE

<

<

SELECT SET

+Hr

Press Up or Down to set the

month. Press Select

to confirm.

When Daylight saving time is enabled, the clock will automatically change from Greenwich Mean Time (GMT)
to British Summer Time (BST) on the last Sunday in March. The clock will automatically change back to GMT on
the last Sunday in October.

MODE

<

<

SELECT SET

+Hr

Press Up or Down to set the

day. Press Select to confirm.

MODE

<

<

SELECT SET

+Hr

Press Up or Down to set the

Daylight Saving Time On or Off.

Press Set to confirm.

EP110 Installation Manual 09

Operating Modes

EP110 can operate in 5 different modes, described in the table below. EP110 can be set to control either the
boiler OR the hot water. You can choose on which one of the channels you connect the controller. To access
operating modes, please press Mode key.

Operation Mode Function

ON Continuously on

ONCE On for 1 period a day, from Program 1 ON to Program 3 OFF

AUTO Automatic program control

ADV When device is in Auto or Once mode, press the MODE

button for 3 sec for selecting Advance (ADV). This will move
the unit into the next program. When the ADV function
ends the device will return to normal program.

OFF Continuously off

For activating the functions described above, press the MODE button. The operating mode is cycled in
the below sequence:

ON Mode

MODE

<

ONCE Mode

MODE

<

<

<

SELECT SET

SELECT SET

Pressing the Mode key once activates the ON Mode. In ON mode, the

+Hr

controller gives the boiler the ON command, so the heating or the hot
water will run continuously.

The circle icon will be rotating in a sequence when the relay
output is ON.

+Hr

Pressing the Mode key twice activate the ONCE Mode. In ONCE mode, the
controller gives the boiler the command to run only for one period per
day (from program 1 ON to program 3 OFF)

10 EP110 Installation Manual

ON Mode

MODE

OFF Mode

Pressing the Mode key 3 times activates the AUTO. In AUTO mode, the

+Hr

controller gives the boiler the ON/OFF command depending on your
schedule.

<

<

SELECT SET

MODE

+Hr

Pressing the Mode key 4 times activates the OFF Mode. In OFF mode, the
controller gives the boiler the OFF command, so the heating or the hot
water will be turned off.

<

<

SELECT SET

ADV Mode

Note: In ONCE or AUTO mode, by long pressing the MODE button, the controller will switch automatically
to ADV. You can cancel the ADV by long pressing the MODE key. The device will then return to ONCE or
AUTO mode. You can’t select ADV by pressing Mode key.

When in Auto mode selecting ADV, the controller will simply toggle the
current auto setting (ON or OFF). For example, if the current program is

MODE

+Hr

set as:

08:00 ON 09:00 OFF 10:00 ON 11:00 OFF

<

<

SELECT SET

Selecting ADV between 8:00 and 8:59 will change the output to OFF, from
9:00 onwards back to AUTO (which is also OFF). Selecting ADV between
9:00 and 09:59 will change the output to ON, from 10:00 onwards back
to AUTO (which is also ON). If the ADV puts the relay ON then the boost

Long press Mode while

in Auto or Once

would apply immediately at the next OFF change, if the ADV puts the
relay OFF then the boost would apply immediately and turn the relay ON.

08:00 OFF 10:00 ON 12:00 OFF 14:00 ON

If ADV occurs at 08:30 and the relay is ON from 08:30 to 12:00. During this period, if at 08:45 +1Hr (Boost) is
pressed, the relay will be ON from 08:30 to 12:00. Boost is applied immediately ie. from 08:45 to 09:45 at the next
change, ie. 12:00. If ADV occurred at 10:30 the relay will be ON from 10:00, OFF from 10:30 (ADV) to 14:00 if no
+1Hr Override. During ADV, if at 10:45 +1Hr (Boost) is pressed, the relay will go ON again at 10:45 (boost starts),
OFF at 11:45 (Boost ends) until ends at 14:00, then ON again at 14:00.

EP110 Installation Manual 11

Programming the EP110

2 types of programs can be set:

• 5+2 (Mo to Fri same and Sat, Sun same)

• Different programs for each 24h.
There are 3 different time sets for each day.

5-2 Days Program Individual Days Program

Weekdays

3 sets of time/channel

Weekends

3 sets of time/channel

Total: 6 settings/week

Setting the 5+2 program

MODE

<

<

SELECT SET

Press Set to start programming.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to select

weekdays or weekends.

Press Select to confirm.

1 Day

3 sets of time/channel

Total: 21 settings/week

+Hr

MODE

<

<

SELECT SET

Press Up or Down to

set start time for prog 1.

Press Select to confirm.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to set

the minutes. Press Select to

confirm.

MODE

<

<

SELECT SET

Press Up or Down to

set start time for prog 2.

Press Select to confirm.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to set

end time for prog 1. Press

Select to confirm.

+Hr

+Hr

MODE

<

<

SELECT SET

+Hr

Press Up or Down to set

the minutes. Press Select to

confirm.

Once you have finished setting the start/end time for the first program,
the device will jump into the second program, and then into third and

2

afterwards into Sat-Sun. Please follow the same steps for each of the
3 programs. Press SET at any time to confirm the setting and return for
program set selection.

12 EP110 Installation Manual

Setting dierent programs for each 24h

Note: Don’t forget to move the jumpers to 24h in order to have the individual program active. After
that please follow the same instructions as for the 5-2 days program.

MODE

<

<

SELECT SET

Press Set to start

MODE

programming.

<

<

SELECT SET

Press Up or Down to set

the minutes. Press Select

to confirm.

+Hr

MODE

<

<

SELECT SET

Monday will flash. Press Select

to confirm.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to set
start time for prog 1. Press

+Hr

Select to confirm.

+Hr

MODE

<

<

SELECT SET

Press Up or Down to set
end time for prog 1. Press

Select to confirm.

+Hr

MODE

<

<

SELECT SET

+Hr

Press Up or Down to set the

minutes. Press Select

to confirm.

MODE

<

<

SELECT SET

+Hr

2

Press Up or Down to

set start time for prog 2.

Press Select to confirm.

Once you have finished setting the start/end time for the first program,
the device will jump into the second program, and then into third and
afterwards into next day. Please follow the same steps for each of the
3 programs. Press SET at any time to confirm the setting and return for
program set selection.

EP110 Installation Manual 13

Functions

Temporary Override

Boost Override (+1Hr override)

Boost Override (+1Hr override) is available in ONCE/AUTO/OFF modes. Boost mode can be activated even in
ADV mode. When boost mode is activated, ADV is canceled. Press +1Hr at current mode to activate the Boost
Override (+1Hr override) setting mode. Boost mode increases the time of the active program by 1-9 hours.
The new setting hour “+x” (x=last boost hour+1 hour) is displayed. Subsequent press of +1Hr will increase
the duration by 1 hour. Maximum duration is 9 hours. If the number rolls back to blank, this will disable the
Boost Override.

MODE

<

<

Press +1Hr to enter

Boost override.

SELECT SET

+Hr

MODE

<

<

SELECT SET

The number of boost hours

will be displayed.

+Hr

MODE

<

<

SELECT SET

+Hr

To exit boost override, press

mode button until number

+x dissapears.

ADV Override

ADV only works in AUTO or ONCE mode. During ADV, press MODE once to cancel ADV and go back to AUTO
/ONCE mode after LCD backlight is turned off. +1Hr override and ADV cannot co-exist in same channel.
During ADV mode, when +1Hr is pressed, override mode will cancel ADV mode then change to Boost mode.
If +1Hr override (Boost) is running, then ADV is selected, ADV will be activated and the previous +1Hr override
will be cancelled.

MODE

<

<

SELECT SET

3 sec 1 sec

Long press Mode while in

Auto or Once to enter ADV

override Mode

14 EP110 Installation Manual

+Hr

MODE

<

<

SELECT SET

+Hr

Short press Mode while in ADV to

exit mode back to auto or Once

Holiday Override

During the period of holiday override, relay should be always Off.
Press and hold at current mode for 3 seconds to activate the Holiday Override setting mode.
The plane icon will be displayed on the LCD and the user’s only option will be to set the number of holiday
days (up to 31). To exit Holiday Override and turn On the relay, long press the key.

Enter Holiday Mode

3 sec

Exit Holiday Mode

MODE

<

<

Press for 3 seconds.

3 sec

MODE

<

<

SELECT SET

SELECT SET

+Hr

MODE

<

<

SELECT SET

+Hr

Press Up/Down keys

to select days.

+Hr

MODE

<

<

SELECT SET

+Hr

Press for 3 seconds.

LCD Backlight

If AC is powered, LCD backlight is activated when or any key is pressed. The backlight will be turned off in
15 seconds after all keys are released.

Controller in current mode.

EP110 Installation Manual 15

Factory Reset

If you want to return to the factory settings please press the Reset button once (use a pin for this action).

MODE

+Hr

<

<

SELECT SET

MODE

<

Press reset button. LCD will turn OFF.

MODE

+Hr

<

<

SELECT SET

MODE

<

<

<

+Hr

SELECT SET

+Hr

SELECT SET

All icons will be displayed. Software version.

16 EP110 Installation Manual

MODE

<

<

Normal Mode.

+Hr

SELECT SET

Technical Info

Product Specication

Model: EP110
Type: Surface Mounted Wired Single Channel Programmable Timer
Memory Backup Lithium battery (CR2032 x1pc)
Power control
Rating 230V/50Hz/3(1)A
Relay SPDT
Protection Rating: IP 30
Environment
Operating Temperature/

0°C ~ 50°C, 10% – 90% non-condensing

Humidity:
Storage Temperature/

-20°C~- 60°C, 10% – 90% non-condensing

Humidity
Programs
Program 5-2 or 24hr individual program (selectable by jumper),

3 settings/day, with holiday override.
Boost Override Yes, max 9 hours(selectable by software)
Holiday Override Yes, max 31 days (selectable by software)
Clock
Clock Format 12 or 24 hour (selectable by software)
Clock Accuracy +/-1 min/month
Daylight Saving Time (DST) Yes, Clock automatically adjusted if DST is enabled.

EP110 Installation Manual 17

Warranty

SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall
perform in accordance with its specification, for a period of two years from the date of installation. SALUS
Controls sole liability for breach of this warranty will be (at its option) to repair or replace the defective product.

Customer Name: ..................................................................................................................................................................

Customer Address: .............................................................................................................................................................

................................................................................................................ Post Code: ...............................................................

Tel No: ................................................................... Email: ......................................................................................................

Company Name: ...................................................................................................................................................................

Tel No: .................................................................. Email: ........................................................................................................

Installation Date: ...................................................................................................................................................................

Installer Name: .......................................................................................................................................................................

Installer Signature: ...............................................................................................................................................................

18 EP110 Installation Manual

SALUS Controls PLC
SALUS House

Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK.

Sales: T: [phone]
E: [e-mail]

Technical: T: [phone]
E: [e-mail]

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development, SALUS Controls plc reserves the right to
change specification, design and materials of products listed in this brochure without prior notice.

Issue Date: April 2017, V001