Salus AS20WRF, AS20BRF Installer's/user's Manual

4 in 1 Digital Thermostat RF

Models: AS20WRF and AS20BRF

INSTALLER / USER MANUAL

Product Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your device completely dry.
Disconnect your device before cleaning it with a dry cloth.

Always isolate the AC Mains supply before installing or working on any components that require
120 VAC 60Hz supply.

Introduction

Thank you for purchasing the 4 in 1 room thermostat. It must be used with the Universal Gateway
SG888ZBWH (purchased separately) when having an Internet connection or with the AKL08RF for
the underfloor system withoul Internet connection. The Universal Gateway allows communication
with other devices in the Wyse.ly system range. Other Zigbee devices include wiring
centre, system receiver & ARV. You can download your SALUS Wyse.ly system App from the
Google Play and App Store.

Installation – First Power Up

The following screens show examples only

MCU software

version will

be shown

ZIGBEE software

version will

be shown
Please make sure that your Universal Gateway is installed. You can use it with both internet
and non internet connection. The LED will be blue when connected to the internet and red
when it’s not connected.

With Internet

Without Internet

* Please note that 88.8 and 8.8 are

a reference to the software version.

If you are installing an underfloor system without an Internet connection, you can use the
coordinator from the AKL08RF instead of the Universal Gateway.

1

4

2

5

3

Tap Scan for equipment
when you want to start
adding equipment to the
App. The gateway will
start flashing red.

Pairing for underfloor with Internet connection

Please follow the on screen instruction in order to complete the pairing process.

76

98

1110

12

Installation – AS20

Mount the back case of the thermostat on the wall. After that please insert the batteries and add
the front case. Make sure to sure to use 4AAA Alkaline batteries.

1

4

2 3

Tap Scan for equipment when
you want to start adding
equipment to the App. The
gateway will start flashing red.

Pairing for radiator system with Internet connection

7

6

10

12

14

11

13

Wait until the LED is
solid red. Press the Open/
Close button once. When
the initialization process is
complete, the LED
will go off.

Press and hold the
for 10 seconds until the ARV
starts flashing red.

Please follow the on screen instruction in order to complete the pairing process.

5

8 9

Installation – Power Up your devices

Please follow the installation procedure for all equipment. After installation, your devices should
look like this:

On step 6 please select your zone number by using the UP or DOWN arrows.

SALUS North America

850 Main Street
Redwood City
CA 94063

T: [phone]
E: [e-mail]

www.salusna.com

SALUS North America is a member of the Computime Group

Maintaining a policy of continuous product development, SALUS Controls plc
reserves the right to change specification, design and materials of products listed in
this brochure without prior notice.

Installation – Receiver AX10RF (optional)

Note: Please install the AX10RF Receiver for your radiator system. This will ensure the
communication between the thermostat and the boiler, giving you the possibility to
switch the boiler on and off. The AX10RF receiver is optional and needs to be purchased
separately.

JG Boiler Receiver Reduced.qxp_Layout 1 24/11/2014 10:17 Page 4

*Configured as RX1(boiler receiver)

*Configured as RX1 (stand alone receiver)

For the latest PFD Instruction Manual, go to www.salusna.com

H

Pairing for radiator system without Internet connection

The pre fix number on the ARV will

change as the ARV(s) pair.

Once all ARV’s have paired press

If you use the maximum number of
ARVs it will automatically take you to
the Mainscreen.

5 sec

5 sec

Setting the time (for systems without internet only)

3 Sec

Use right and left to select

the day of the programs.

Use right and left to select

the day of the programs.

Set the program / schedule (for systems without internet only)

5/2

Individual

7 Days

Installation – Check the paired devices

If you want to see what devices are connected to your Universal Gateway you can
know exactly by using the Identify procedure.

Tap the tile from
the Dashboard.

Tap the name
of your device.

Factory reset

If you have made an error or need to change your system parameters please follow
steps below. This should only be done by your installer.

Now you are ready to

set up your system

as desired.

Press all three buttons

simultaneously

Wait until the LED is
solid red. Press the Open/
Close button once. When
the initialization process is
complete, the LED
will go off.

Press and hold the
for 10 seconds until the ARV
starts flashing red.

If the pre-configured program is not suitable for your application, hold down the
bottom three keys for a short time, until the display shows SEL PROG. Do these
settings before adding the thermostat to the universal gateway.

Installation – System Parameters

Use or to select the type of unit.

After selection has been made, press to confirm.

Programmable Thermostat

Digital Thermostat

Hot water timer

Selecting unit type

Tap the Identify
button. Your device
will start flashing

Tap the button again
after identifying your
device.

OR

5 sec

OR

5 sec

5 sec

2

4

1

3

Pairing for underfloor system without Internet connection

5 sec

7

1

2

3

4

5

6

7

8

5

6

9

On step 6 please select your zone number by using the UP or DOWN arrows.