Salton RHOK3123 User Manual

Carousel Cordless Kettle

OWNER’S MANUAL

RHOK3123

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed, including the following:

READ ALL INSTRUCTIONS

1. Do not touch hot surfaces. Use handles or knobs.

2. To protect against fire, electric shock, and injury to persons,
do not immerse cord, plugs, Power Base or Kettle in water or
other liquid.

3. Close supervision is necessary when any appliance is used by
or near children.

4. Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the Kettle or Power Base.

5. Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions or has been damaged in
any manner. Return the appliance to the nearest authorized
service facility for examination, repair, or adjustment.

6. The use of accessory attachments not recommended by
the appliance manufacturer may result in fire, electric shock
or injury.

7. Do not use outdoors.

8. Do not let the cord hang over the edge of a table or counter
or touch hot surfaces.

9. Do not place on or near a hot gas or electric burner, or in a
heated oven.

10. To disconnect the appliance, make sure the Switch is OFF,
then remove the plug from the electrical outlet.

11. Do not use the Kettle other than for heating water.

12. Water can remain hot for some considerable time after
boiling and can present a scalding hazard.

13. Scalding may occur if the Lid is removed during the boiling
cycle or while the Kettle is hot.

14. Ensure that the Kettle is properly located on the Power Base
before switching it on.

15. Use the Kettle only with the Power Base supplied.

16. Remove the Kettle from its Power Base before filling
or pouring.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

1

3-PRONG GROUNDED TYPE PLUG

This appliance is equipped with a grounded type 3-wire cord (3­prong plug). This plug will only fit into an electrical outlet made for
a 3-prong plug. This is a safety feature. If the plug should fail to fit
the outlet, contact an electrician to replace the obsolete outlet.
Do not attempt to defeat the safety purpose of the Grounding
Pin part of the 3-prong plug.

SHORT CORD INSTRUCTIONS

A short power supply cord is provided to reduce the risk resulting
from becoming entangled in or tripping over a longer cord.

Longer detachable power-supply cords or extension cords are
available and may be used if care is exercised in their use.

If a longer detachable power-supply or extension cord is used,
(1) the marked electrical rating of the cord set or extension cord
should be at least as great as the electrical rating of the
appliance, and (2) the cord should be arranged so that it will not
drape over the countertop or tabletop where it can be pulled on
by children or tripped over accidentally.

The extension cord should be a grounding-type 3-wire cord.

ELECTRIC POWER

If the electric circuit is overloaded with other appliances, your
appliance may not operate. It should be operated on a separate
electrical circuit.

PLASTICIZER WARNING

CAUTION: To prevent Plasticizers from migrating from the
finish of the counter top or table top or other furniture, place
NON-PLASTIC coasters or place mats between the appliance
and the finish of the counter top or table top.

Failure to do so may cause the finish to darken, permanent
blemishes may occur or stains can appear.

2 19

INTRODUCTION

The OPTEC™ DISC heating element fitted in your Russell Hobbs
Kettle is a revolutionary new concept in water heating
technology, making it one of the fastest, most efficient Kettles
available today.

The OPTEC™ DISC converts more of your electricity into usable
heat and allows better heat transfer from element to water—
which means less power wasted and faster boiling times.

The OPTEC™ DISC heating element is resistant to the permanent
build-up of scale which can degrade the performance of a
traditional element, causing overheating and shortening its life.

®

Filter
Tab

Spout

Filter

Power
Connector

Power Base
(P/N 30849)

Lid (P/N 30847)

MAX Water
Guide

Steam
Tube

OPTEC™ DISC
Heating Element

(inside)

Filter Tab

OFF (O)

ON (I )

ON/OFF
Switch

Cord Storage Area

Water Filter

(P/N 30848)

3

SOUND LEVELS

Because the OPTEC™ DISC heating element boils water more
rapidly than the traditional type of heating element, you may find
that this Kettle is louder than many other Kettles. This is normal, and
should not be cause for alarm.

BEFORE USING FOR THE FIRST TIME

Remove all packaging from the Kettle and its Power Base. Remove
any labels from the outer stainless steel surfaces.

1. Make sure the ON/OFF Switch on the Kettle is in the OFF (0)
upper position. Fill the Kettle with water up to the MAX
Water Guide.

2. Gently position the Kettle over the power connector
and centered on the Power Base, taking care not to

spill any water.

3. Plug the power cord into the electrical outlet.

4. Press the ON/OFF Switch down ( I ) to turn the Kettle ON.

5. When the water has boiled, the Kettle will turn itself OFF
automatically and the Switch will return to the OFF (0) position.

6. Discard the boiled water and allow the Kettle to cool. Rinse out
with cold water. Repeat steps 1 through 6 at least three times, to
remove any manufacturing dust, etc.

EASY-TO-USE POWER BASE WITH 360° ACCESS

With the specially designed Power Base and central Power
Connector, you can set the Kettle on the Base at any angle,
from any position.

Position the Power Base on a flat, heat-resistant surface, as close to
an electrical outlet as possible. Shorten the power cord to suit by
wrapping excess power cord in the Cord Storage area underneath
the outer rim of the Power Base.

FILLING THE KETTLE WITH WATER

Remove the Kettle from its Power Base, remove Lid. Fill the Kettle
through the Lid opening. Use at least 350ml (10 fl oz/2 cups) of
water, and DO NOT FILL ABOVE THE BOTTOM OF THE MAX WATER

GUIDE INSIDE THE KETTLE.
CAUTION: When refilling, take care when lifting the Lid, as the

WARNING: DO NOT OVERFILL THE KETTLE. IF THE KETTLE IS OVERFILLED,

Kettle, if hot, may be full of steam. Keep your face,
hands, etc. clear of the opening.

THERE IS A RISK THAT BOILING WATER
MAY BE EJECTED.

4 17

Operating Instru c t i o n s

POWER ON / AUTO OFF

1. Make sure the ON/OFF Switch on the Kettle is in the OFF (0)
position. Fill the Kettle with water up to the MAX Water Guide.

2. Gently position the Kettle over the power connector
and centered on the Power Base, taking care not to

spill any water.

3. Plug the power cord into the electrical outlet.

4. Press the ON/OFF Switch down to (I) to turn the Kettle ON.

5. When the water has boiled, the Kettle will turn itself OFF
automatically and the Switch will raise to the OFF (0) position.

6. To turn the Kettle OFF before the water boils, manually move
the ON/OFF Switch up to the OFF (0) position, or simply lift the
Kettle from its base. Your Kettle will turn OFF and the Switch will
return to the OFF (0) position automatically.

NOTE: When you lift the Kettle from its Power Base, you may

see moisture on the surface of the Power Base. This is
the steam used to turn the Kettle OFF automatically
after boiling, which then condenses and is allowed to
escape via vents in the underside of the Kettle. This is
perfectly normal, and should not be a cause for alarm.

WARNING: To avoid the risk of splashing water, pour slowly and do

WARNING: When filling or carrying the Kettle, do not tilt it

WARNING: Do not turn the Kettle ON unless it contains at least

not over-tilt the Kettle.

backward, as this may allow water to pass on to the
control area through the steam opening. Should this
occur, the Kettle must be emptied and allowed to dry
completely before use.

350ml (12 fl oz/2 cups) of water. Misuse of this kind will
shorten the life of the element.

BOIL-DRY AUTO OFF

If the Kettle is accidentally turned on when it does not contain
sufficient water, a boil-dry device will automatically turn it OFF.

Unplug the Power Base from the electrical outlet. Remove the
Kettle from the Power Base. Wait until the Kettle has cooled down
before filling, as the element will be hot and spitting may occur.

516

TO BOIL A SECOND POT OF WATER

Turn the Kettle OFF for 15 minutes and allow it to cool.
WARNING: Failure to allow Kettle to cool may cause water to

overheat and spray hot steam. The hot steam can
cause severe burns.

User Maintenance Instru c t i o n s

SCALE

Scale is mainly calcium carbonate (chalk), a harmless, naturally
occurring mineral found in most water supplies. ‘Hard’ water
contains more of this mineral than ‘soft’ water. When water is
heated, the minerals in the water solidify. This can make the water
appear cloudy; it may form a thin film on the surface of the water
after boiling; it may look like whitish pieces of plastic in the water; it
may form a film on the walls or element of the Kettle. On traditional
Kettle elements, scale forms a hard white ‘crust’ which adversely
affects performance and reduces the life of the element.

• The OPTEC™ DISC heating element fitted to your Kettle has
been designed and developed to resist this build-up of
permanent scale deposits on its surface.

• As soon as you notice a “film” forming on the water, or, when
cleaning the Water Filter, if you notice a “film” on the walls or the
element, simply rinse the Kettle and wipe it out.

• To reduce the build-up of scale residues, always empty any

residual water after boiling.

Any marking or residue on the element will not affect its
performance or efficiency. If you do decide that you want to
descale the Kettle, to remove any such residue, or to restore the
appearance of the Kettle, you may do so, but please use a
proprietary brand of descaler, suitable for use in plastic-bodied
products (even metal Kettles have plastic parts).

When using descaler, follow the manufacturer’s instructions. After
descaling, empty the Kettle and rinse it out several times with fresh
water, then fill it with fresh water, boil and discard the water. This
should ensure that no chemical residues are left in the Kettle.

6 15

WATER FILTER SYSTEM WITH REMOVABLE FILTER

Your Kettle is equipped with a unique Water Filter System which
prevents scale particles from getting through the Kettle spout. This
Water Filter is removable for cleaning.

You must clean the Water Filter whenever there are any
noticeable deposits left on the Water Filter or if the rate of pouring
begins to reduce.

1. Before fitting or removing the Water Filter, empty the Kettle,
turn the Kettle OFF (0), and allow it to cool down completely.

2. Remove the Kettle from its Power Base.

3. Remove the Lid from the Kettle.

4. Press gently down on the tab at
the top of the Water Filter to
release it from the Kettle rim then
pull gently away from the spout.

WARNING: Do not use excessive

5. Grasp the Water Filter gently by

6. To clean the Water Filter, rinse it under a tap while brushing it

7. Replace the Water Filter. Make sure that your hands are clean

8. Tilt the bottom of the Water Filter forward slightly and ease it

9. Push gently down on the tab at the top of the Water Filter, to

NOTE: To work properly, the Water Filter must be located centrally

10. Rinse the Kettle with fresh water and it’s ready for use.

force, as this might
damage the Water Filter.

the edges, keeping your fingers
clear of the mesh, and pull it out
through the top of the Kettle.

with a soft brush.

and free from soap, cream or anything which might taint
the water.

forward, toward the spout, until the bottom of the Water Filter
engages in the groove between the Kettle wall and the
bottom of the Kettle.

ease the Water Filter under the rim, then push forward, toward
the spout. The two guides on the front of the Water Filter
should fit into holes in the metal plate covering the spout.

behind the spout.

7

User Maintenance Instru c t i o n s

CLEANING INSTRUCTIONS

1. Unplug the Power Base from the electrical outlet and let the
Kettle cool down completely before cleaning.

2. Clean the Kettle, inside and out, with a damp cloth.

3. When wiping the inside of the Kettle, take care not to catch
your hand on the edge of the MAX Water Guide.

4. Do not use harsh or abrasive cleaners or solvents.

5. Do not immerse the Kettle or the Power Base in water or any

other liquid.

6. Make sure that all connectors and sockets are kept dry.

8

MISES EN GARDE

IMPORTANTES

Pendant l’utilisation de tout appareil électroménager, toujours
observer les précautions élémentaires de sécurité, y compris les
suivantes :

LIRE L'ENSEMBLE DES INSTRUCTIONS

1. Ne pas toucher les surfaces chaudes. Utiliser les poignées ou
les boutons.

2. Afin de réduire les risques d'incendie, d'électrocution et de
blessures, ne pas immerger le cordon, les prises, le socle, ou la
bouilloire dans l'eau ou dans tout autre liquide.

3. Se montrer particulièrement vigilant lorsqu’un appareil
électroménager est utilisé par des enfants ou à proximité
d’enfants.

4. Débrancher l’appareil de la prise lorsqu’il n’est pas en service,
ainsi qu’avant de procéder au nettoyage. Laisser refroidir
avant de monter ou de démonter des pièces, ainsi qu’avant
de procéder au nettoyage de la bouilloire ou de le socle.

5. Ne pas se servir de l'appareil si le cordon ou la fiche est
endommagé(e), s'il ne fonctionne pas correctement, ou s'il a
été endommagé d’une quelconque manière. Renvoyer
l’appareil au centre SAV agréé le plus proche afin qu’il puisse
être examiné ou réparé, ou faire l’objet de réglages.

6. L’utilisation d’accessoires non recommandés par le fabricant
peut entraîner des risques d’incendie, d’électrocution, ou de
blessures.

7. Ne pas utiliser à l’extérieur du domicile.

8. Ne pas laisser le cordon pendre du bord d’une table ou d’un
plan de travail, ni toucher des surfaces chaudes.

9. Ne pas placer sur ou près d’un brûleur à gaz ou électrique
chaud, ni dans un four chaud.

10. Pour débrancher, veiller à ce que l'interrupteur soit bien sur la
position d'arrêt 'OFF', puis retirer le cordon de la prise murale.

11. La bouilloire doit servir uniquement à faire bouillir de l'eau.

12. L’eau peut rester chaude pendant longtemps après ébullition
et peut donc présenter des risques de brûlure.

10

Wa r r a n t y : This Russell Hobbs( product is warranted by Salton, Inc. to be free from defects in materials or

LIMITED ONE YEAR WA R R A N T Y

workmanship for a period of (1) year from the original purchase date. This product warranty covers only the
original consumer purchaser of the product.

Warranty Coverage: This warranty is void if the product has been damaged by accident in shipment,
unreasonable use, misuse, neglect, improper service, commercial use, repairs by unauthorized personnel,
normal wear and tear, improper assembly, installation or maintenance abuse or other causes not arising out
of defects in materials or workmanship. This warranty is effective only if the product is purchased and
operated in the USA, and does not extend to any units which have been used in violation of written
instructions furnished with the product or to units which have been altered or modified or to damage to
products or parts thereof which have had the serial number removed, altered, defaced or rendered illegible.

Implied Wa r r a n t i e s : ANY IMPLIED WARRANTIES WHICH THE PURCHASER MAY HAVE ARE LIMITED IN
D U R ATION TO ONE (1) YEAR FROM THE DATE OF PURCHASE. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.

Warranty Performance: During the above one-year warranty period, a product with a defect will be
either repaired or replaced with a reconditioned comparable model (at our option) when the product is
returned to the Repair Center, or the purchase price refunded. The repaired or replacement product will be
in warranty for the balance of the one-year warranty period and an additional one-month period. No charge
will be made for such repair or replacement.

Service and Repair: Should the appliance malfunction, you should first call toll-free 1 [phone]
between the hours of 9:00 am and 5:00 pm Central Standard Time and ask for CONSUMER SERVICE stating
that you are a consumer with a problem. Please refer to model number RHOK3123 when you call.

I n - Warranty Service (USA): For an appliance covered under the warranty period, no charge is made for
service or postage. Call for return authorization (1 800 233-9054).

Out-of Warranty Service: A flat rate charge by model is made for out-of-warranty service. Include
$8.00 (U.S.) for return shipping and handling. We will notify you by mail of the amount of the charge for
service and require you to pay in advance for the repair or replacement.

For Products Purchased in the USA, but Used in Canada: You may return the product insured,
packaged with sufficient protection, and postage and insurance prepaid to the USA address listed below.
Please note that all customs duty / brokerage fees, if any, must be paid by you and we will require you to pay
the cost of customs duty / brokerage fees to us in advance of our performing any service.

Risk During Shipment: We cannot assume responsibility for loss or damage during incoming shipment.
For your protection, carefully package the product for shipment and insure it with the carrier. Be sure to
enclose the following items with your appliance: any accessories related to your problem, your full return
address and daytime phone number, a note describing the problem you experienced, a copy of your sales
receipt or other proof of purchase to determine warranty status. C.O.D. shipments cannot be accepted.

To re t u rn the appliance, ship to: To contact us, please write to, call, or email:

ATTN: Repair Center Salton, Inc.
Salton, Inc. P.O. Box 7366
708 South Missouri Street Columbia, MO 65205-7366
Macon, MO 63552 1 - 8 0 0 - 2 3 3 - 9 0 5 4

Limitation of Remedies: No representative or person is authorized to assume for Salton, Inc. any other
liability in connection with the sale of our products. There shall be no claims for defects or failure of
performance or product failure under any theory of tort, contract or commercial law including, but not
limited to negligence, gross negligence, strict liability, breach of warranty and breach of contract. Repair,
replacement or refund shall be the sole remedy of the purchaser under this warranty, and in no event

shall Salton be liable for any incidental or consequential damages, losses or expenses.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

Legal Rights: This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.

For more information on Salton products: visit our website:
©2002 Salton, Inc. All rights reserved. P/N 60959
Made in China 2 / 0 2

E-mail: [e-mail]

w w w. s a l t o n - m a x i m . c o m