SaltDogg WB200A User Manual
by Buyers
Toll-Free Fax 800-841-8003 • buyersproducts.com
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Assembly Instructions
WB100A
Heavy-Duty Carbon Steel
Walk Behind Salt Spreader
WB200A
Heavy-Duty Stainless Steel
Walk Behind Salt Spreader
17
—continued inside
by Buyers
2
3
1
16
9
6
4
7
14
15
5
17
8
12
13
10
11
18
21
24
20
22
23
Check contents of box against the parts list to make
sure all components are included. When ordering
replacement or spare parts refer to the parts list for part
numbers.
2
by Buyers
M6x40 (5)
M6x20 (2)
M6x45 (3)
M6x60 (4)
M6x70 (2)
M6x50 (4)
TOOLS NEEDED FOR ASSEMBLY
• (2) 10mm Wrenches
• (2) ½" Wrenches
• (1) Slotted Screwdriver
• (1) Pliers
• (1) 3mm Allen Wrench (included)
Fastener Selection Guide
FULL ONE YEAR WARRANTY
Manufacturer will repair, or at manufacturer’s discretion will replace
any part of this salt spreader which proves to be defective in workmanship or material under normal use for a period of one year from
the date of delivery to the original purchaser. Any cost incurred
in returning the product to the supplier is the responsibility of the
consumer.
EXCLUSIONS
Manufacturer shall not be liable for special, incidental, or consequential damages, or for damages resulting from lack of necessary maintenance, from misuse, abuse, acts of God, or alteration of the product.
Some states do not al low the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
Bill of Materials (for all figures)
WB100A = CS / WB200A = SST
ITEM PART NO. QTY DESCR IPTI ON
1 3009153cs/sst 1 UPPER FRA ME ASSY
3007853cs/sst 2 Upper Frame
— 1 M6x60 Hex Head Cap Screw
— 1 M6 Locking Nut
2 3009154cs/sst 1 LOWER FRAME ASS Y
3009168cs/sst 1 Lower Frame (Left)
3009169cs/sst 1 Lower Frame (Right)
3007857cs/sst 1 Long Crossmember
— 2 M6x40 Hex Head Cap Screw
— 2 M6 Locking Nut
3 3009155cs/s st 1 HOPPER SUPPORT ASSY
3007856cs/sst 2 Hopper Support
3009171cs/sst 1 Short Crossmember
— 2 M6x40 Hex Head Cap Screw
— 2 M6 Locking Nut
4 3009156 1 HOPPER ASSY
3009144 1 Hopper
3009162 1 Restric tor Assembly
5 3009157 1 SPINNER ASSY
3009150 1 Spinner Shaft
3007863 1 Spinner
— 1 Cotter Pin
3008882 1 Support Bracket
3008892 1 Bushing
3009364 1 Spacer
3008879 1 Pinion Gear
— 1 Spring Pin
6 3008142 1 DEFLECTOR A SSY
— 3 M6 Wing Nut
3007877 1 Long Deflector
3007878 2 Short Deflector
3007879 1 Deflector Rod
3007880 2 Deflector Hanger
— 5 M6x20 Carriage Bolt
— 2 M6 Locking Nut
7 3009160 1 CONTROL HANDLE ASSY
3009172 1 Control Handle
3007868 1 Plastic Washer
3007869 1 Control Plate
3007876 1 Stop Spacer
— 2 M6 Wing Nut
— 1 M6x20 Carriage Bolt
8 3009163cs/sst 1 REAR DEFLECTOR ASSY
3008812cs/sst 1 Mounting Bracket
3007877 1 Long Deflector
— 1 M6x20 Carriage Bolt
— 1 M6 Wing Nut
9 3009159cs/sst 1 HAND LE
10 3009173 1 UPPER LINK AGE
11 3009174 1 LOWER LINK AGE
12 3007862 1 DRIVE WHE EL
13 3008135 1 COAST W HEEL
14 3009158 1 AXLE
15 3008880 1 DR IVE G EAR
16 3009175 1 LINK AGE PLATE ASSY
17 3009170cs/sst 2 HOPPER SUPPORT BRACKET
18 3008813 1 SC REEN
19 3007993 1 R AIN COVER
300 9161 1 HARDWAR E BAG
20 3008881 1 SP INNER SHAFT SUP PORT
21 — 6 SHIM WASHER
22 — 3 A XLE BU SHING
23 — 2 COTTE R PIN
— 5 M6x40 Hex Head Cap Screw
— 3 M6x45 Hex Head Cap Screw
— 4 M6x60 Hex Head Cap Screw
— 2 M6x70 Hex Head Cap Screw
— 4 M6x50 Machine Screw
— 2 M6 Flat Washer
— 20 M6 Locking Nut
— 2 Jam Nut
— 2 M6x20 Hex Head Cap Screw
24 3009767 2 LOCKING COLLAR S
3009768 1 Allen Wrench
3
by Buyers
FRONT
3
2
17
M6x60
M6x60
M6x60
1. Loosely assemble the Lower Frame(2) to the Hopper
Support Assembly(3) including the two Hopper Support
Brackets(17). Start the nuts, but DO NOT FULLY
TIGHTEN.
4
by Buyers
5
12
13
21
23
22
15
20
21
M6x45 WITH
M6 FLAT WASHERS (x2)
M6x40
M6x45
23
DRIVE WHEEL
MOUNTING HOLE
DRIVE GEAR
MOUNTING HOLE
22
14
17
24
M6x45
M6x40
RIB SIDE MUST
FACE AWAY FROM
LARGE GEAR
SHIM
WASHER
COTTER
PIN
M6x45
(WITH WASHERS)
MOUNT TO HOLES
IN FRAME
2. Loosely assemble the axle components to the frame
A. Attach the Drive Gear(15) to the axle with a
m6x40 bolt
B. Position the Spinner Shaft Support(20) and orient it
as shown
C. Add one Shim Washer(21) as shown
D. Add the two stainless steel Locking Collars(24)
E. Add two plastic axle Bushings(22)
F.
Insert the axle and components thru the frame holes
and add third Bushing to coast wheel side as shown.
3. Position the Spinner Assembly(5) into the Spinner
Shaft Support(20) and assemble the parts so that
the small gear fits into the drive gear. Using a Cotter
Pin(23), pin the Shim Washer against the Spinner Shaft
Support as shown.
4. Loosely mount the spinner shaft mounting plate
to the frame using the two m6x45 bolt that have flat
washers pre-mounted.
(with washers)
5
Loading...