Salsbury Industries Anchoring Bracket User Manual

Anchoring Bracket - One Wide Locker Without Legs

Installation Instructions

Thank you for selecting Salsbury’s standard lockers. These
instructions are intended to assist you in attaching one wide lockers
without legs to a concrete base or floor.

Step 1 – Drill Anchor Hole Locations

Begin the locker installation by placing the locker on its back. Clamp
the appropriate drill template (provided) onto the bottom shelf against
each side wall of the locker. The appropriate drill template is the one
that measures 4” shorter than the locker depth. Drill four (4) 3/16”
diameter holes and four (4) 3/8” diameter holes through the bottom
shelf of the locker in the locations depicted on the templates.

Step 3 – Fasten Locker to Concrete

Attach the locker to the concrete base or floor by installing four (4)
1/4” x 2-1/4” long concrete screws (provided) and four (4) 1/4” flat
washers (provided) through the four (4) drilled 3/8” diameter holes in
the bottom shelf, through the slots in the anchoring brackets, and
through the holes drilled into the concrete. The four (4) #8 x 1/2”
long self-drilling screws may be removed after installing the concrete
screws. Installation is now complete.

Step 2 – Attach Anchors and Drill Concrete Screw Holes

Remove the templates. Attach two anchoring brackets that are 4”
shorter than depth of locker underneath the bottom shelf of the locker
by placing four (4) #8 x 1/2” long self-drilling screws (provided)
through the four (4) drilled 3/16” diameter holes in the bottom shelf
and through the pre-drilled holes in the anchoring bracket. Set the
locker in place on the concrete base or floor. Drill four (4) 3/16”
diameter holes into the concrete base or floor through the four (4)
drilled 3/8” diameter holes in the bottom shelf and through the slots in
the anchoring brackets. Drill holes at least 2-3/8” deep from the top
surface of the bottom shelf.

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.lockers.com engineering

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2013 Salsbury Industries. All rights reserved. (Rev. 01, 2/19/13) Page 1 of 1

@lockers.com

Anchoring Bracket - Three Wide Locker Without Legs

Installation Instructions

Thank you for selecting Salsbury’s standard lockers. These
instructions are intended to assist you in attaching three wide lockers
without legs to a concrete base or floor.

Step 1 – Drill Anchor Hole Locations

Begin the locker installation by placing the locker on its back. Clamp
the appropriate drill template (provided) onto the bottom shelf of the
left locker against the side wall of the locker. The appropriate drill
template is the one that measures 4” shorter than the locker depth.
Drill two (2) 3/16” diameter holes and two (2) 3/8” diameter holes
through the bottom shelf of the locker in the locations depicted on the
template. Repeat these steps against the right wall of the right locker
if no additional lockers will be installed next to it.

Step 3 – Fasten Locker to Concrete

Attach the locker to the concrete base or floor by installing two (2)
1/4” x 2-1/4” long concrete screws (provided) and two (2) 1/4” flat
washers (provided) through the two (2) drilled 3/8” diameter holes in
the bottom shelf, through the slots in the anchoring bracket, and
through the holes drilled into the concrete. The two (2) #8 x 1/2” long
self-drilling screws may be removed after installing the concrete
screws. Repeat these steps on the far right locker. To complete the
installation, bolt all lockers in a row together through their side walls
with fasteners provided. Installation is now complete.

Step 2 – Attach Anchor and Drill Concrete Screw Holes

Remove the template. Attach an anchoring bracket that is 4” shorter
than depth of locker underneath the bottom shelf of the left locker by
placing two (2) #8 x 1/2” long self-drilling screws (provided) through
the two (2) drilled 3/16” diameter holes in the bottom shelf and
through the pre-drilled holes in the anchoring bracket. Set the locker
in place on the concrete base or floor. Drill two (2) 3/16” diameter
holes into the concrete base or floor through the two (2) drilled 3/8”
diameter holes in the bottom shelf and through the slots in the
anchoring brackets. Drill holes at least 2-3/8” deep from the top
surface of the bottom shelf. Repeat these steps to the right locker if
installing an additional anchor.

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.lockers.com engineering

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2013 Salsbury Industries. All rights reserved. (Rev. 01, 2/19/13) Page 1 of 1

@lockers.com