Salsbury Industries 98000 User Manual

Plastic Lockers – 98000 Series

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.lockers.com [e-mail]

SIDE

PANEL

BACK

PANEL

OTHER

SIDE PANEL

BASE PANEL

(THICKER)

SIDE

PANELS

TOP

PANEL

BACK

PANEL

LOWER

(FIRST)

UNIT

UPPER

(2nd, 3rd, 4th)

UNITS

LEVELING FEET

(NOT SHOWN)

TOP PANEL

(THINNER)

LOWER

(FIRST)

UNIT

FILLER

STRIPS

FILLER STRIPS

INSTALLED

Models 98168 & 98368 Eight Tier

Assembly Instructions

Thank you for selecting Salsbury 98000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a
good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the
lockers must be anchored to the wall, the floor, or both. Please read the entire assembly instruction document before beginning assembly.

Step 1. Insert the back panel tabs into the pockets along the rear
edge of the side panel. Tap with soft mallet to engage two (2) latch
points.

Step 4. Install a thinner top horizontal panel on top of the unit.

Step 2. Press another side panel onto the tabs on the other side of

the back panel. Tap to engage as above.

Step 3. Join and press down the sides-and-back-panel assembly
from step 2 above into the base panel as shown below. The base
panel is the thicker of the five (5) horizontal panels provided. Then
thread four (4) leveling feet provided into the bottom of the base
panel.

Step 5. Assemble three (3) identical units the same as Steps 1
through 4, except installing the thinner top panel on each instead of
the thicker base panel. These units will not have leveling feet.

Step 6. If no optional sloping hood is ordered, install the three (3)
filler strips into the recesses in the top panel of one (1) of the upper
units. This will be the uppermost unit after the units are stacked.

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2010 Salsbury Industries. All rights reserved. (Rev. 01, 12/8/2010) Page 1 of 3

Plastic Lockers – 98000 Series

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.lockers.com [e-mail]

PANEL WITH

FILLER STRIPS

(IF NO OPTIONAL

SLOPING HOOD)

BASE PANEL

(THICKER)

CAM

LOCK

PLATE

HASP

LOCK
KNOB

NUT

ALL

UNITS

STACKED

SCREWS

(2)

NAMEPLATE

(OPTIONAL)

SCREW

DOOR

HINGE

DIVIDER

PANEL

DOOR

HINGE

Models 98168 & 98368 Eight Tier

Assembly Instructions

Step 7. Stack the three (3) upper units onto the lower unit. Press all
units firmly together. Use a soft rubber mallet if necessary.

Step 8. Insert one (1) of four (4) divider panels in between each of
the horizontal panels previously installed. The panels slide in
grooves in the side panels and may need the use of a soft rubber
mallet to fully engage the two small latch pins into the holes in the
front edge of the side panels.

Step 9. Attach the plastic oval lock plate to the front of the eight (8)
doors with two (2) screws from the rear of the door. Do not over
tighten. Insert the stainless steel hasp through hole in front of doors
making sure cutout is facing downward. Secure by threading nut
provided onto it from the rear. Insert lock knob through hasp from
front of door making sure hole in lock knob is positioned downward.
Attach cam to rear of lock knob shaft with screw provided. Be sure
the cam is pointing horizontally toward the outside of the door when
the lock knob is positioned vertically, and is properly engaged with
the square shaft on the end of the lock knob.

Step 10. Fasten the eight (8) hinges (one (1) for each of the eight (8)
doors) provided in the hardware package securely to each hinge
position with the screws provided as shown below. Fasten each of
the eight (8) doors to the appropriate hinge. Ensure that the molded
pin in the upper right corner of each door is engaged in the mating
hole in the corner of the underside of each horizontal panel.

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2010 Salsbury Industries. All rights reserved. (Rev. 01, 12/8/2010) Page 2 of 3