Salsbury Industries 92000 User Manual
Plastic Lockers – 92000 Series
T
(
T
A
T
Models 92168 & 92368 Double Tier
Assembly Instructions
Thank you for selecting Salsbury 92000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a
good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the
lockers must be anchored to the wall, the floor, or both. Please read the entire assembly instruction document before beginning assembly.
Step 1. Insert the back panel tabs into the pockets along the rear
edge of the side panel. Tap with soft mallet to engage two (2) latch
points.
Step 4. Join two long interlocking plastic joint pieces and one short
interlocking plastic joint piece into a U-shaped assembly as shown
below. Press the U-shape assembly down onto the U-shaped top
edges of the lower (first) unit assembly from step 3.
LOWER
(FIRST)
UNI
SIDE
PANEL
Step 2. Press another side panel onto the tabs on the other side of
the back panel. Tap to engage as above.
OTHER
Step 3. Join and press down the sides-and-back-panel assembly
from step 2 above into the base panel as shown below. The base
panel is the thicker of the three (3) horizontal panels provided. Then
thread four (4) leveling feet provided into the bottom of the base
panel.
BACK
PANEL
SIDE
PANEL
LOWER
(FIRST)
UNI
SHORT
STRIP
INTERLOCK
LONG
STRIPS
JOINT
Step 5. Assemble a second unit per Steps 1 and 2. Press this
assembly into the joint assembly on the top of the lower half of the
unit from Step 4 above. Then press down one of the two top panels
(thinner) onto the top of the assembly.
SSEMBLY
TOP PANEL
(THINNER)
INTERLOCKING
JOINT
ASSEMBLY
LOWER
(FIRST)
UNI
JOINT
BASE PANEL
THICKER)
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2010 Salsbury Industries. All rights reserved. (Rev. 05, 7/22/2010) Page 1 of 4
LEVELING FEET
(NOT SHOWN)
SALSBURY I
1010 East 62nd Street, Los Angeles, CA 90001-1598
Phone: 1-800-562-5377 Int’l Phone: 323-846-6700
Fax: 1-800-562-5399 Int’l Fax: 323-846-6800
www.lockers.com engineering
NDUSTRIES
ASSEMBLY
@lockers.com
LOWER HALF
OF THE UNIT
Plastic Lockers – 92000 Series
(
)
Models 92168 & 92368 Double Tier
Assembly Instructions
Step 6. If no optional sloping hood is ordered, install the three filler
strips into the recesses in the top of the remaining (second) top
panel.
FILLER
STRIPS
Step 7. Assemble a second compartment per steps 1 though 5
except without a base panel and using the second top panel with the
filler strips installed. This unit will not have leveling feet. Stack this
second unit onto the first unit as shown below. Use a mallet if
necessary.
SECOND
UNIT
BOTH
UNITS
STACKED
FILLER
STRIPS
INSTALLED
SECOND
TOP PANEL
(THINNER)
Step 9. Install a lock catch bar at the center of each of the two (2)
compartments, on the left front inside edge of the side panel with the
four (4) short flathead screws provided.
LOCK
CATCH BAR
FOUR (4)
SCREWS
Step 10. Attach the plastic oval lock plate to the front of the two (2)
doors with two (2) screws from the rear of the door. Insert the
stainless steel hasp through hole in front of doors making sure cutout
is facing downward. Secure by threading nut provided onto it from
rear. Insert lock knob through hasp from front of door making sure
hole in lock knob is facing downward. Attach cam to rear of lock
knob shaft with screw provided. Be sure the cam is pointing toward
the outside of the door and is properly engaged with the square shaft
end of the lock knob.
FIRST
UNIT
BASE PANEL
(THICKER)
Step 8. Install screws and hole covers where side panels join to top
panels and base panel. There are 18 screws and hole covers on
each side of the two sides of the assembly (36 in total).
HOLES
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
SCREWS
Phone: 1-800-562-5377 Int’l Phone: 323-846-6700
www.lockers.com engineering
Copyright © 2010 Salsbury Industries. All rights reserved. (Rev. 05, 7/22/2010) Page 2 of 4
FIRST
TOP PANEL
THINNER
COVERS
SALSBURY I
1010 East 62nd Street, Los Angeles, CA 90001-1598
Fax: 1-800-562-5399 Int’l Fax: 323-846-6800
NDUSTRIES
SCREW
CAM
NUT
SCREWS (2)
@lockers.com
PLACARD
(OPTIONAL)
LOCK
PLATE
HASP
LOCK
KNOB
Loading...