Salsbury Industries 51000 User Manual

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Extra Wide Standard Lockers – 51000 Series

Single Tier Installation Instructions

Thank you for selecting Salsbury’s extra wide standard single tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker
components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on
the outside of the locker or on the exposed surface.

One Wide Locker Assembly

Step 1: Attach the top shelf, bottom shelf, and the first single coat hook to the back

panel.

Step 3: Attach the second side panel and the right rear leg to the assembly of Step 2.
On 15” deep lockers attach a third single coat hook. On 18” deep lockers substitute a
single coat hook with a double bend for the third single coat hook and install the coat
rod as shown on page 3. The locker chassis is now complete.

Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the
first side panel, the left rear leg, and the hat shelf to the assembly from Step 1. On 15”

Step 4: Attach the pre-assembled door frame onto the assembly of Step 3.

deep lockers attach the double coat hook to the bottom of the hat shelf and attach a
second single coat hook to the first side panel. On 18” deep lockers omit the double
coat hook and substitute a single coat hook with a double bend (not shown) instead of
the second single coat hook (this will accommodate the coat rod).

Step 5: Tighten all fasteners checking for squareness of the locker while tightening.
Attach optional sloping hood, end bases or front base (see pages 4 and 5).

Step 6: Place the locker in the installed location and anchor to the floor, wall, or to
both. Individual job conditions will dictate the type of fastening anchors to use (not
provided).

Step 7: Fasten all lockers in a row together by installing fasteners provided through
the side panels. Installation is now complete.

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]
www.lockers.com [e-mail]

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2014 Salsbury Industries. All rights reserved. Page 1 of 5 3/27/14

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Extra Wide Standard Lockers – 51000 Series

Single Tier Installation Instructions

Three Wide Locker Assembly

Step 1: Attach a top shelf, a bottom shelf, and the first single coat hook to a back

panel.

Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the
first side panel, the left rear leg, and the first hat shelf to the assembly of Step 1. On
15” deep lockers attach the first double coat hook to the bottom of the first hat shelf
and attach a second single coat hook to the first side panel. On 18” deep lockers omit
the double coat hook and substitute a single coat hook with a double bend (not shown)
instead of the second single coat hook (this will accommodate the coat rod).

Step 3: Attach the second top shelf, the second bottom shelf, and an additional single
coat hook to the second back panel as in step 1.

Step 4: Simultaneously attach the assembly of Step 3 (second Step 1 assembly), the
second side panel, and the second hat shelf to the assembly of Step 2. On 15” deep
lockers attach the second double coat hook and attach two additional single coat
hooks to the second side panel. On 18” deep lockers omit the second double coat
hook and substitute two additional single coat hooks with a double bend (not shown)
instead of the single coat hooks and install a coat rod as shown on page 3.

Step 5: Attach the third top shelf, the third bottom shelf, and an additional single coat
hook to the third back panel as in steps 1 and 3.

Step 6: Simultaneously attach the assembly of Step 5 (third Step 1 assembly), the
third side panel, and the third hat shelf to the assembly of Step 4. Repeat the Step 4
coat hooks instructions to attach additional coat hooks and coat rods.

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]
www.lockers.com [e-mail]

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2014 Salsbury Industries. All rights reserved. Page 2 of 5 3/27/14