Salsbury Industries 4874 User Manual

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.mailboxes.com [e-mail]

Deluxe Mailbox Posts – 4870, 4872, 4873 and 4874

Post Assembly Installation Instructions

Installing Arm(s) on Deluxe Mailbox Posts

Thank you for selecting Salsbury’s deluxe mailbox post. This instruction sheet is for assembling the 1-sided or 2-sided deluxe mailbox post. All hardware to
assemble the deluxe mailbox post is provided.

When you install a curbside or roadside mailbox, make sure that it is easily accessible to the mail carrier. By regulation it should be 41” to 45” from the ground or
street surface up to the inside floor of the mailbox. The door should be set back 6” to 8” back from the front face of the curb or the road edge. However, you should
check with your local postmaster to ensure that the mailbox is installed according to local regulations.

4870 – 1 Sided

First check to see that all the parts and fasteners in the carton have been
located and identified according to the illustration below. Also refer to the
illustration below to position the parts correctly.

1. Attach the small right-angle bracket to the post with the long leg on top
with two (2) 5/16”-18 x 2” long pan head bolts.

2. Attach the long square-tube arm to the small right angle bracket with two
(2) 1/4”-20 x 1/2” long flat-head socket screws.

3. Attach the large decorative arch to the post and the long arm with four (4)
5/16”- 8 x 1” long hex flange head bolts. Cover with cap plugs.

4. Attach the other small right-angle bracket with the long leg on the bottom
with two (2) 5/16”-18 x 2” long pan head bolts.

5. Attach the short square-tube arm to the small right-angle bracket with two
(2) 1/4’-20 x 1/2” long flat-head socket screws. This completes the
assembly.

4872 – 2 Sided for 2 Mailboxes
4873 – 2 Sided for 3 Mailboxes
4874 – 2 Sided for 4 Mailboxes

First check to see that all the parts and fasteners in the carton have been
located and identified according to the illustration below. Also refer to the
illustration below to position the parts correctly. The 4873 has the same
parts as the 4872, except one (1) arm is longer. The 4874 has the same
parts as the 4872, except the two (2) arms are longer.

1. Attach the small right-angle bracket to the post with the long leg on top
with two (2) 5/16”-18 x 2” long pan head bolts.

2. Attach the long square-tube arm to the small right angle bracket with two
(2) 1/4”-20 x 1/2” long flat-head socket screws.

3. Attach the large decorative arch to the post and the long square-tube arm
with four (4) 5/16”-18 x 1” long hex flange head bolts. Cover with cap plugs.

4. Repeat steps 1 through 3 above for the second arm on the other side of
the post. This completes the assembly.

4870 Assembly

4872, 4873 and 4874 Assembly

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 04, 3/17/14)

SALSBURY INDUSTRIES

1010 East 62nd Street, Los Angeles, CA 90001-1598

Phone: [phone] Int’l Phone: [phone]

Fax: [phone] Int’l Fax: [phone]

www.mailboxes.com [e-mail]

Deluxe Bridge Style Mailbox Post – 4875

Post Assembly Installation Instructions

Thank you for selecting Salsbury’s deluxe bridge style mailbox post. This instruction sheet is for assembling the deluxe bridge style mailbox post. All hardware to
assemble the deluxe bridge style mailbox post is provided.

When you install a curbside or roadside mailbox, make sure that it is easily accessible to the mail carrier. By regulation it should be 41” to 45” from the ground or
street surface up to the inside floor of the mailbox. The door should be set back 6” to 8” back from the front face of the curb or the road edge. However, you should
check with your local postmaster to ensure that the mailbox is installed according to local regulations.

First check to see that all the parts and fasteners in the carton have been located and identified according to the illustration below. Also refer to the illustration below
to position the parts correctly.

1. Attach a right-angle bracket to a post with the long leg on top with two (2) 5/16”-18 x 2” long pan head bolts.

2. Attach a short square-tube arm to the right angle bracket with two (2) 1/4”-20 x 1/2” long flat-head socket screws.

3. Attach a decorative arch to the post and the short square-tube arm with four (4) 5/16”-18 x 1” long hex flange head bolts. Cover with cap plugs.

4. Attach another right-angle bracket to the other side of the post with the long leg on top with two (2) 5/16”-18 x 2” long pan head bolts.

5. Attach the long square-tube arm to the right angle bracket with two (2) 1/4”-20 x 1/2” long flat-head socket screws.

6. Attach another decorative arch to the post and the long square-tube arm with four (4) 5/16”-18 x 1” long hex flange head bolts. Cover with cap plugs.

7. Repeat steps 1 through 6 above for the other the post. This completes the assembly.

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Copyright © 2014 Salsbury Industries. All rights reserved. 3/17/14