SALSBURY INDUSTRIES
1010 East 62nd Street, Los Angeles, CA 90001-1598
Phone: 1-800-624-5269 Int’l Phone: 323-846-6700
Fax: 1-800-624-5299 Int’l Fax: 323-846-6800
www.lockers.com www.mailboxes.com engineering@mailboxes.com engineering@lockers.com
Cell Phone Lockers - 19000 Series
Surface Mounted Installation Instructions
Installation of the Surface Mounted Enclosure
Remove the locker unit from the enclosure. Drill mounting holes in
the enclosure to fasten it to the mounting surface. It is important to
use at least four (4) fasteners (not provided) and place one each at
the four (4) corners of the mounting surface (either on the rear panel
or the bottom panel). Choose appropriate hardware for the particular
conditions of the installation.
Installing the Cell Phone Locker into the Enclosure
Install the locker unit into the enclosure by sliding it into the enclosure
until its front peripheral flange is flush against the front of the
enclosure. Open the four corner compartments of the cell phone
locker. Install #8 x 1-1/4 in. long screws (provided) through the top
and bottom of the locker unit into the enclosure. Close the
compartment doors.
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 12, 1/21/2014) Page 1 of 10
SALSBURY INDUSTRIES
1010 East 62nd Street, Los Angeles, CA 90001-1598
Phone: 1-800-624-5269 Int’l Phone: 323-846-6700
Fax: 1-800-624-5299 Int’l Fax: 323-846-6800
www.lockers.com www.mailboxes.com engineering@mailboxes.com engineering@lockers.com
Cell Phone Lockers - 19100 Series
Surface Mounted with Front Access Panel
Installation Instructions
Installation of the Surface Mounted Enclosure
Remove the locker unit from the enclosure. Drill mounting holes in
the enclosure to fasten it to the mounting surface. It is important to
use at least four (4) fasteners (not provided) and place one each at
the four (4) corners of the mounting surface (either on the rear panel
or the bottom panel). Choose appropriate hardware for the particular
conditions of the installation.
Installing the Cell Phone Locker into the Enclosure
Install the locker unit into the enclosure by sliding it into the enclosure
until its front peripheral flange is flush against the front of the
enclosure. Open the front panel access compartment of the cell
phone locker then open the front panel. Install #8 x 3/4 in. long
screws (provided) through the slots in the sides of the front peripheral
flange of the locker unit into the enclosure. Close the front panel
then the front panel access compartment.
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 12, 1/21/2014) Page 2 of 10
SALSBURY INDUSTRIES
1010 East 62nd Street, Los Angeles, CA 90001-1598
Phone: 1-800-624-5269 Int’l Phone: 323-846-6700
Fax: 1-800-624-5299 Int’l Fax: 323-846-6800
www.lockers.com www.mailboxes.com engineering@mailboxes.com engineering@lockers.com
Cell Phone Lockers – 19000/19100 Series
Surface Mounted Installation Instructions
The surface mounted cell phone locker may be installed on the surface of a wall, on a table or a counter top. It is the installer’s
responsibility to ensure the unit is properly anchored to prevent tearing out of a wall or tipping over on a table or counter top.
See below for further information.
WARNING: Installation of the surface mounted cell phone locker unit must be to a surface of sufficient load
bearing strength. Attachment of the enclosure to the surface must be with fasteners that can adequately
support the weight of the surface mounted cell phone locker unit. Installing to a deficient load bearing
mounting surface and/or use of inadequate fasteners could cause the surface mounted cell phone locker unit to
fall from the surface possibly resulting in serious injury.
Installation Planning
1. Consider the weights in the table on the next page when designing the wall or selecting the appropriate fasteners and anchors to
be used.
2. If attaching to studs in a custom built wall, determine the optimum location of the wall studs to which to fasten the units. Frame the
wall with wood studs. Build a robust wall.
3. If attaching to studs in an existing wall, determine the stud locations, and position units to maximize the number of studs to which
the units will be attached.
4. If not attaching to studs, choose an appropriate high strength anchor, especially if attaching directly to drywall. When attaching to
drywall, place the anchor and fastener as close as possible to the studs to which the drywall is attached.
5. If attaching to a table or countertop, consider the combined weights of the units when selected the location to mount the units on
top of. Ensure the mounting structure is of adequate strength to prevent the units from falling through the mounting surface.
6. If attaching to a table or countertop, use fasteners of adequate strength to secure the units to prevent the units from tipping over.
On the surface mounted cell phone locker with a front access panel, use fasteners of adequate strength to secure the units to the
table or countertop to prevent the units from tipping over when the front access panel is fully opened.
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 12, 1/21/2014) Page 3 of 10
Loading...