SALORA
PROJECTOR
MODEL: 60BFH3800
ENGLISH
Warning …………………………………………………………………………………………………………………………………..
1
Safety Precautions …………………………………………………………………………………………………………………..
2
Caution ……………………………………………………………………………………………………………………………………
3
Installation ……………………………………………………………………………………………………………………………..
4
Structural Diagram …………………………………………………………………………………………………………………..
7
Panel Keys Introduction …………………………………………………………………………………………………………..
8
Input Terminals ……………………………………………………………………………………………………………………….
9
Turning ON/OFF ………………………………………………………………………………………………………………………
10
Image Adjustment …………………………………………………………………………………………………………………..
11
Remote Control Introduction ………………………………………………………………………………………………….
12
Menu Settings ………………………………………………………………………………………………………………………….
13
Multimedia Menu ……………………………………………………………………………………………………………………
16
Connection to a PC Instructions ……………………………………………………………………………………………….
17
Troubleshooting ………………………………………………………………………………………………………………………
18
Specifications …………………………………………………………………………………………………………………………..
19
Accessory List …………………………………………………………………………………………………………………………..
20
CONTENT
WARNING
High Voltage, only to be
Warning
Do not look directly into the light of the lens, this can cause damage to the eyes, especially
for children.
Warning:
Do not place the projector on a wet surface, this can cause an electric shock.
opened by professionals
WARNING
Important Operation Instructions
Dangerous High Voltage indicated
Caution class A device:
As the projector is class A device, it can cause electromagnetic interference.
Installation of the batteries in the remote control:
To avoid any damage to the remote control, please be sure to install the batteries correctly,
matching the polarity in the battery compartment.
Never let children change the batteries, this can be dangerous.
SAFETY PRECAUTIONS
Please read this manual carefully before operating the projector and keep it for future
reference
Please follow the instructions mentioned in this manual when operating or if the projector
needs maintenance.
1. Cleaning
Unplug the power cable before
cleaning it. Clean the projector
with a soft damp cloth. Do not use
any liquid detergent or spray
cleaner.
2. Accessories
In order to avoid any damage, only
use the accessories recommended
by the manufacturer.
3. Wet surfaces
Do not place the projector on any
wet surfaces.
4. Installation
Please install this projector on a
stable and even surface.
5. Ventilation
Do not place the projector on a
bed, sofa carpet and the like.
6. Power
Always check before using the
projector that the mains voltage
corresponds to the voltage of the
projector.
7. Ground wire
The plug on the power cord is
connected to a ground wire.
8. Protect the power cable
Make sure the power is in perfect
working condition and not
damaged in any way before using
it.
9. Lightning
When there is a storm and
lightning disconnect the power
cord from the mains. When not in
use for an extended period, also
unplug the projector from the
mains.
10. Repair
Never try to open the projector for
any maintenance. Always ask a
professional if any repairs have to
be done.
11. Heat
Make sure not to position the
projector near a heat source or any
heating devices. This can shorten
the life-span of the projector.
CAUTION
Installation
• In order to extend the life-span of the projector, do not use it under damp, dusty and
foggy conditions, unless the lens and ventilation openings are cleaned frequently.
• For the best possible performance, please use the projector in a dark room, with the
curtains drawn, protecting it from direct strong light. Make sure the projector is
positioned on a stable and level surface, so that it cannot fall and cause personal
damage. Please use this projector carefully, if it falls or hits something it can be
damaged, especially the lens.
• Working temperature of the projector is: 5°C - 35°C
• Storage temperature of the projector is: 0°C - 40°C
• Do not block the ventilation openings of the projector. If the interior temperature of
the projector is too high, it will automatically shut down to protect itself from
damage. To prevent overheating, please clean the filter once a month.
Turning the projector on/off
• To turn the projector on, connect the power cable to the mains. Then press the
power key on the panel. It will take a couple of minutes for the lamp to start
operating.
• To turn the projector off, turn press the power key on the panel and the projector
will be turned off. Then remove the power cable from the mains.
INSTALLATION
Screen
DVD Player
Projector
Seats
Speaker C
Door
Speaker
Speaker
Speaker
Subwoofer
Amplifier
Speaker
Avoid direct sunlight to obtain the best quality image. Draw the curtains, when using
FULL SETTING
the projector during day time.
INSTALLATION
Distance
16:9
4:3
50”
1.63m
1.90m
70”
2.25m
2.65m
100”
3.10m
3.55m
120”
3.08m
4.40m
Screen
Screen
Axis
Projector
Incorrect Installation
Correct Installation
Incorrect Installation
Standard Setting (Front Projection)
Please refer to the following table to adjust the picture size and distance (from the lens to
the screen).
Dimensions Image
(For the best quality image, we advise you to not use the projector over 80”.)
Please allow a ± 3% margin to the image sizes in the table above. If the distance is less or
more than the minimum or maximum parameters, the image can get blurry.
Warning:
Please check the diagram below for the trapezoid adjustment.
Symmetrie
INSTALLATION
Projector
screen
projector
Front projection
Ceiling mount
projector
screen
Rear projection
Ceiling mount
projector
Rear projection
Table mount
screen
Front projection
Table mount
screen
Installation procedure
Contact a professional installer to mount the projector to the ceiling.
Follow the instructions below for the correct projector positions.
Warning:
1. This can be damaged beyond repair if not correctly mounted on a ceiling or on a
surface.
2. This projector should only be used in an environment where the temperature does
not exceed the range of 5°C - 35°C. Failure to do so can cause the projector to
malfunction.
3. Malfunction can occur if the projector is used in dusty, wet, moist or smoky
conditions.
4. Poor ventilation can cause overheating which can lead to damage to the projector as
well as life threatening situations.
INSTALLATION
1.
Vent cool air intake
2.
Level-stand adjustment
3.
IR receiver
4.
Focus Lens
5.
Keystone
6.
Power switch
7.
Input terminals
8.
Speaker
9.
Vent hot air exhaust
10.
Level-stand adjustment
11.
Projector mount holes
12.
Rating plate
13.
Vent cool air intake
Panel key instruction
1) Navigation Key
By pressing this key, you can adjust the menu by using the Up/Down as well as the
Left/Right navigation buttons.
2) Menu
By pressing this key, you can enter the main menu. With the navigation buttons you
can scroll through the various options.
3) Source
With this key you can choose the input source: USB/AV/YPbPr/HDMI/VGA.
4) Power Key
With this key you can put the projector on/off. This function can also be found on the
remote control.
5) Indicator Light
Red: Standby mode
Blue: Operation mode
Input Terminals
Y/Pb/Pr
Component Video input
AV
Video output
L-Out, R-Out
Audio output left and right
L-In, R-In
Audio output left and right
VGA
VGA input
HDMI 1/2
HDMI signal input
USB 1/2
USB Flashdrive
Caution:
projector.
Interface
To avoid any damage, connect the input signal cable correctly prior to switching on the
Turning the projector On/Off
Turning the projector on:
1) Install the two new batteries into the remote control before using the projector.
2) For switching the projector on, you need to press the power switch at the back, the
indicator light will turn red.
3) Press the power button on the top panel or the remote control, the indicator light
will turn blue.
4) After a few seconds, the lamp will begin to work.
5) When you use the projector for the first time, the image may appear blurry or
distorted. Please refer to the Image Adjustment chapter for instructions to adjust the
image quality.
6) You can always reset the system parameters at any time. Please refer to the menu
Setting chapter.
Turning the projector off:
1) When the projector is in operation, press the power key and the projector will enter
standby mode.
2) When the projector is in standby mode, the auto protection system will be activated.
If you would like to restart the projector, press the power key again.
Image Adjustment
Keystone
Screen
Projector
Height
Screen
Projector
Height
Adjustable feet
When you are using the projector for the first time, the image may appear unclear or
trapezoid, because the focus and keystone haven’t been adjusted yet. You can adjust the
image by carrying out the following steps.
Focus adjustment
Turn the lens clockwise, after that turn it slowly counter clockwise. At the same time check
the resolution point. The best position of the lens will be determined when the image is
clear.
Please note: When you have moved the projector from a cold to a warm environment,
water vapor may occur. Do not turn on the projector until the vapor has disappeared
completely.
Keystone
If a projected image has a keystone distortion, you can adjust it with the keystone
adjustment. The image has a trapezoid shape when the screen or projector is not level.
Please reposition the projector to improve its angle to the screen. However, the outline of
the image cannot be focused.
If the image cannot be corrected by using the keystone adjustment to correct the trapezoid
distortion, please lower the projector to the center of the screen vertically.
Remote Control
On/Off
Up ! Mute
Down
Info
Display Information
Left
Pic.
Picture mode
Right
Audio
Audio mode
Previous
Enlarge/reduce
image size
Repeat function
multimedia)
AB cycle (when using
USB multimedia)
Audio tracks (when
multimedia)
Subtitle (when using
USB multimedia)
To go to a certain
USB multimedia)
USB
Enter USB mode
Vol +/-
Volume up/down
Next/Previous
channel
16 :9 / 4 :3 Aspect
Ratio
Trun image 360
degrees
M
Menu
FRZ
Freeze image
exit
Exit
1,2,3..9
Choose TV channel
q
Zoom
Rep.
AB
Aud.T
Subt.
Goto
(when using USB
using USB
time (when using
W
S
A
D
7
8
5
6
12
3
OK Confirm
Next
Rewind
Fast Forward
Play/Pause
Stop
S Switch source CH +/-
R
Flip
Loading...