How it Works
Salda
Loading...
R
S
V
Loading...
Loading...
Smarty 2X V 1.3

Salda Smarty 3X V 1.2, Smarty 2X V 1.1, Smarty 2X V 1.2, Smarty 2X V 1.3, Smarty 3X V 1.1 User And Service Technical Manual

...
AHU WITH HEAT RECOVERY
Smarty 2X V Smarty 3X V
Subject to technical modication
User‘s and service technical manual
Smarty 2X-3X V_P0110_AZ_0004
Smarty 2X/3X V
Cover opening 7 Filters maintenance 7 Fans maintenance 7 Heat exchanger maintenance 9 Bypass Dampers and Pre-Heater maintenance 9 Control board maintenance 10
Recommendations for Installation of Unit Functional
Wiring Diagram 11
Smarty 2X/3X V connection possibilities 11
Mounting on wall 16 Mounting on Legs 16 Connection of the unit to electric network 17
1.1 System modes 19
1.2 System Control 19
1.3 System status 20
1.4 Indications of Functions, Alarms and Warnings 20
1.5 Setting Date and Time 20
1.6 Weekly Schedule 20
1.7 Holiday Schedule 20
1.8 Winter/Summer Mode 20
1.9 “BOOST” Function 21
1.10 Protection against Dryness 21
1.11 Night Cooling Function (not available in Smarty
1.12 Air Filter Timer 21
1.13 Display and Cancellation of Alarms and Warnings
1.14 Event Log (History) 22
1.15 System Versions and Running Time 22
1.16 Air Flow Adjustment 22
1.17 PID Controller Adjustment 23
1.18 Manual Control of Components 23
1.19 System Monitoring 23
1.20 Stand-By Mode Blocking 23
1.21 Supply Air Temperature Control and Compensati-
1.22 Supply Air Temperature Limits 23
1.23 Mode from an External System Contactor 23
1.24 Fan Speeds from an External System Contactor
1.25 Filter Protections 24
1.26 Fire Protection against External System Contac-
1.27 CO2 Reduction Function (only using additional
extract air CO2 sensors) 24
1.28 Changing Passwords 24
1.29 Restoring Factory Defaults 24
1.30 Fan Control 24
1.31 Damper Control 25
1.32 Heat Exchanger Control 25
1.33 Heaters 26
1.34 Digital Input Conguration 26
1.35 Sensor Conguration 26
1.36 Communications Line Conguration 26
System protection 39
Recommendations before the start of the unit (before
Possible faults and troubleshooting 39 Sensors and their technical information 39
Fire Protection Signal Input (Fire protection input
Outdoor Air Pre-Heater 44 Pre-Heater Capacity by Regions 45 System mode ir Fan speed switch 45 Supply air CO2 or RH (input 0-10VDC) 45 Extract air CO2 or RH (input 0-10VDC) 46
Room CO
CO2 concentration according to Pettenkofer limit 47
transmitter installation recommendation 46
2
Smarty 2X/3X V 1.1 Version - Heater Control 47 Smarty 2X/3X V 1.2, 1.3 Versions - Heater Control 49 Connection of Supply and Extract Air Dampers 51 Connection of Remote Control Panel or ModBus 51
Operation and Alarm Indication (Smarty 2X/3X V 1.1)
Fire Place Connection (Smarty 2X/3X V 1.1) 52
2
www.salda.lt
Smarty 2X/3X V
www.salda.lt
3
Smarty 2X/3X V
200003025238
IV
PV
KE
PE
M
0.084 kW; 0.92 A; 230/50 V/Hz; ~1
0.085 kW; 0.93 A; 230/50 V/Hz; ~1 kW; A; 0 V/Hz; ~0 kW; A; 0 V/Hz; ~0
0.005 kW; 0.021 A; 24/50 V/Hz; ~-
0.17 kW; 1.87 A; IP-34
TOTAL:
gu072489 / 2014.03 www.salda.lt
1
3
4
5
2
6
200003025238
IV
PV
KE
PE
M
0.084 kW; 0.92 A; 230/50 V/Hz; ~1
0.085 kW; 0.93 A; 230/50 V/Hz; ~1 kW; A; 0 V/Hz; ~0 kW; A; 0 V/Hz; ~0
0.005 kW; 0.021 A; 24/50 V/Hz; ~-
0.17 kW; 1.87 A; IP-34
TOTAL:
gu072489 / 2014.03
www.salda.lt
1
3
4
5
2
6
P
A
V
Y
Z
DY
S
E
X
A
P
L
E
PAVADINIMAS
TITLE
M
585 mm
700 mm
2120 mm
Warning – pay attention Additional information
Stick the auxiliary label on the unit (on an easily accessible place) or on the dashed place of a technical manual in order to keep the important informa­tion about the unit.
1 – Logo 2 – Internal usage code 3 – Brand name 4 – Technical data 5 – Units number 6 – Web address
STICK HERE
• All units are packed in the factory to withstand regular conditions of transportation.
• Upon unpacking, check the unit for any damages caused during transportation. It is forbidden to install damaged units!!!
• The package is only for protection purpose!
• While unloading and storing the units, use suitable lifting equipment to avoid damages and injuries. Do not lift units by holding on power supply cables, connection boxes, air extract or exhaust anges. Avoid hits and shock overloads. Before installation units must be stored in a dry room with the relative air humidity not exceeding 70% (at +20 °C) and with the average ambient temperature ranging between +5 °C and +30 °C. The place of storage must be protected against dirt and water.
• The units must be transported to the storage or installation site using forklifts.
• The storage is not recommended for a period longer than one year. In case of storage longer than one year, before the installation it is necessary to verify whether the bearings of fans and motor rotate easily (turn the impeller by hand) and if the electric circuit insulation is not damaged or the moisture is accumulated.
8
0
0
m
m
Smarty 2X V Smarty 3X V
m m
35 3
mm
5
2
6
485 mm
700 mm
2160 mm
755 mm
8
m
m
0
0
7
0
0
m
m
0 mm
0
7
700 mm
585 mm
585 mm
912 mm
1058 mm
700 mm
2120 mm
585 mm
4
Preparation for transportation
www.salda.lt
Smarty 2X V Smarty 3X V
Smarty 2X/3X V
1
2
3
4
Standard package (without optional accessories) includes:
1. Key - 1 pc.
2. Sealing tape FIX-PV 6x20
3. Suspension bracket - 1 pc.
4. Condensate outlet pipe G3/8 - 1 pc.
- Do not use the unit for purposes other than its’ intended.
- Do not disassemble or modify the unit in any way which may lead to mechanical failure or injury.
- Use special clothing and be careful while performing maintenance and repair jobs – the unit’s and its components’ edges may be sharp and cutting.
- Do not wear loose clothing that could be entangled in to operating unit.
- Do not place ngers or other foreign objects through inlet or exhaust guards or into connected duct. If a foreign object enters the unit, immediately disconnect power source. Before removing object, make sure that any mechanical motion has stopped, the heater has cooled down and the restart is not possible.
- Do not connect to any other power source than indicated on the model label.
- Do not place or operate unit on unsteady surfaces and mounting frames.
- Mount the unit rmly to ensure safe operating.
- Never use this unit in any explosive or aggressive elements containing environment.
- Do not use the unit if external connections are broken or damaged. If there are any defects, stop operating the unit and replace the damaged parts im­mediately. That can be performed only by qualied electrician.
- Do not use water or another liquid to clean electrical parts or connections.
- If you notice water on electrical parts or connections, stop operating the unit.
Smarty 2X/3X V are residential air handling unit with a high e󰀩ciency (up to 90 %) counter ow heat exchanger. The unit provides ventilation in the home and takes the heat from the exhausted air. AHU complies with ErP 2018 and Passivhaus requirements. The unit is operated by a separate remote control panel or though separate MB-Gateway by PC. Remote control panel and MB-Gateway are optional and not included in standard pack­age. Control functions depend on selected control board type: MiniMCB or MiniMCB basic. Smarty 2X/3X V operates within the limits of the airow diagrams and is suitable for indoor operation only. Required ambient temperatures must be from +5 oC to +40 oC. For the cold climate zones (air temperatures below -6 oC), integrated or optional pre-heater is required.
www.salda.lt
5
Smarty 2X/3X V
1
2
3
4
5
6
7
15
14
13
12
11
8
9
10
Smarty 2XV, 3XV are available in three versions:
Optional heating elements
*- only pre-heater or
Product name
Control board
Type
Heat recovery
Temperature
control
Bypass damper
(lter pollution
Pressure sensor
monitoring)
heater
Duct based
Integrated pre-
Smarty 2X V 1.1 Mini MCB Premium + + + - + - +
Smarty 2X V 1.2 Mini MCB Basic Advanced + + + - - +*
Smarty 2X V 1.3 Mini MCB Basic Basic + + - - - +*
Smarty 3X V 1.1 Mini MCB Premium + + + + + - +
Smarty 3X V 1.2 Mini MCB Basic Advanced + + + - - +*
Smarty 3X V 1.3 Mini MCB Basic Basic + + - - - +*
Not suitable for swimming pools, saunas and other similar facilities.
Smarty 2X V Smarty 3X V
8
1
2
3
4
5
6
7
9
10
11
12
13
14
15
1
2
3
4
5
6
7
Air Pre-
Heater
heater
Duct based
Air Heater
8
9
10
11
12
13
14
15
16
16
1. Flange 4 pcs.
2. Outdoor air temperature sensor (TL)
3. Outdoor air lter (G4/(F7 - optional)) and the EPP cover*
4. Extract air sensor (TA)**
5. Bypass damper (M1)**
6. Preheater (PE1)**
7. Extract air lter (G4) and the EPP cover*
10. Control board.
11. Supply air fan (PV)**
12. Exhaust air fan (IV)**
13. Galvanized steel casing
14. EPP casing
15. Heat exchanger
16. Condensate tube plugs
8. Supply air sensor
9.CE7/7 power supply cable - 3 m.
*Filter EPP cover only on Smarty 3X V. ** Depends on unit type.
• Unit is designed to operate only indoors.
• It is forbidden to use the unit in potentially explosive environment.
• Unit is designed to supply/extract only clean air (free of chemical compounds causing metal corrosion, of substances aggressive to zinc, plastic and rubber, and of particles of solid, adhesive and  bred materials).
Outdoor
- temperature min./max. [°C]
- humidity [%] 90
-15 / +40**
-40 / +40***
-5/ +40* Extract
- temperature min./max.*
- humidity [%] 60
[°C] +15 / +40
* - Outdoor air temeperature without preheater (Salda Antifrost o󰀨) ** - with integrated preheater (Smarty 2X/3XV 1.1) or Smarty 2X/3XV 1.2/1.3 (Salda Antifrost on) *** - with optional preheater on duct Salda Antifrost uses dis-balancing of the air ow and it may cause negative pressure in premises.
6
www.salda.lt
Unplug unit from mains before opening the door (discon­nect the power plug from the outlet or if there is a two-pole automatic circuit breaker installed – disconnect it as well. It is necessary to ensure that it won’t be turned on by third parties) and wait until the full stop of the fans (for about 2 min.).
Smarty 2X V Smarty 3X V
Smarty 2X/3X V
Smarty 2X V Smarty 3X V
Remowing Smarty 2X V lters: key loosened and removable product doors, removable lters. Uses G4 / (F7 - optional) lters.
Dirty lters increase air resistance, airow into the room.
Changing lters, lters reload timer control. Description of remote control panel functions is provided in the remote control panel technical documentation or on the website www.salda.lt.
Allowed to operate the unit without lters!
Remowing Smarty 3X V lters: opening lter cover (pulling the strap),
retractable lter. Uses G4 / (F7 - optional) lters.
It is advisable to change the lters every 3 - for 4 months, or according to their testimony timer remote control.
• Maintenance should be performed only by experienced and trained sta󰀨.
• The fan should be inspected and cleaned at least once a year.
• Be sure the fan is disconnected from power source before performing any maintenance or repair.
• Observe sta󰀨 safety regulations during maintenance and repair.
• The motor is of heavy duty ball bearing construction. The motor is completely sealed and requires no lubrication. Supplied air fan from X15, X2, X4. Extract air fan from X16, X2, X4.
• Detach fan from the unit.
• Impeller should be specially checked for buil-up material or dirt which may cause an imbalance. Excessive imbalance can lead to accelerated wear on motor bearings and vibration.
• Clean impeller and inside housing with mild detergent, water and damp, soft cloth.
• Do not use high pressure cleaner, abrasives, sharp instruments or caustic solvents that may scratch or damage housing and impeller.
• Do not plunge the motor into any uid while cleaning impeller.
www.salda.lt
7
Smarty 2X/3X V
• Make sure, that impeller ’s balance weights are not moved.
• Make sure the impeller is not hindered.
• Mount the fan back into the unit. Connect the fan to power supply source.
• If after maintenance the fan does not start or stop itself, contact the producer. Malfunction of the fan can be identied according to the pressure in the system (when pressure switches are connected). When there is a folt in fans’ motor, any separate notice is shown on the control panel.
Be sure the unit is disconnected from power source before performing any maintenance or repair.
- Remove the fan connectors from the control board. Supplied air fan from X15, X2, X4. Extract air fan from X16, X2, X4.
Note:
- X2, X4 are common for both fans.
- Reassembly shall be executed in the reverse order.
X2
Smarty 2X V
X15
X4
X16
Smarty 3X V
8
www.salda.lt
Smarty 2X/3X V
• Proceed to maintenance and repair after any rotation in the fan stopped.
• Clean the heat exchanger once a year.
• Firstly take out heat exchanger cassette carefully. Submerge it into a bath and wash with warm soapy water (do not use soda). Then rinse it with weak hot water stream (too strong stream can fold the plates). Place back the heat exchanger only when it is completely dry.
Smarty 2X V Smarty 3X V
Bypass damper and pre-heater are mounted on one block. The pre-heater shall be disconnected by removing X29 connector. The bypass damper shall be disconnected by removing X25 .
Smarty 2X V Smarty 3X V
X29
X25
www.salda.lt
9
Smarty 2X/3X V
- Unscrew the front bolt securing the control board holder to the unit casing.
- Withdraw the automation through the front part.
- Disconnect the connectors from the control board.
- The connectors are marked according to connection location. Thus during automation reassembly please observe the marking of the connection location of connectors and controller. If the marking on the controller terminals is not visible follow the PCB information provided in this passport (see miniMCB description: Fig. 2 and Fig. 3):
Smarty 2X V Smarty 3X V
• All the metering, control and execution units shall be mounted in freely accessible locations for maintenance, repairs or replacement.
• Prior to handover to the user, the pre-commissioning activities shall be performed to ensure proper operation of the automatic control system of the air handling unit. Power plug socket shall be installed at a distance to ensure unstrained power cable of the unit. Standard length of the unit power cable shall be: ~2.5 m long from the unit casing.
Prior to connecting the unit to the mains, the door shall be closed.
The installed plug socket shall be of at least the same nominal current as the unit nominal current, which is indicated in the unit rating plate.
Unit shall be connected to the mains through the cur­rent leakage relay (30mA).
After complete dismantling of the unit control auto­mation and its reinstallation, when connecting the automation connectors, it is necessary to check if the connector conductors are not damaged or otherwise broken.
• Install the control panel at the designed location.
• Connect the connection cable supplied with the remote control panel kit between the control panel and the HVAC unit. It is recommended to install the remote control board separately from the power cables. NOTE: If the cable is used together with other power cables, the remote control panel cable shall be shielded with grounded shielding armour. NOTE: the remote control panel shall be connected and/or disconnected only after disconnecting power supply to HVAC unit.
10
www.salda.lt
Smarty 2X/3X V
Electrical equipment connection to the control board terminals. Control board connectors shall be of the following cross sectional area.
Control board 0,5 mm
2
1,5 mm
2
2,5 mm
2
miniMCB X1, X2, X3, X4, X5, X6, X7 X9, X13, X14, X15, X16 X10, X11, X12, X17
miniEX1 X19, X20, X21, X23 - -
Power supply - - Xp1
Automation E zone, connector Xp1 general power connection to the unit ~1/230 VAC.
Smarty 2X V Smarty 3X V
Exhaust air Supply air Outdoor air air Extract
Right side connection Left side connection
www.salda.lt
11
Smarty 2X/3X V

Technical data

phase/voltage
power/current [kW/A] 0,035/0,35 0,083/0,75
Exhaust air fan
Supply air fan
Total power consumption power/current [kW/A] 0,67/3,35 0,07/0,75 0,07/0,75 1,37/6,75 0,17/1,55 0,17/1,55
Automatic control integrated + +
Thermal e󰀩ciency 92 %* 88 %*
Insulation of walls [mm] 30 30
Netto weight [kg] 25 39
Pre-heater power/current [kW/A] 0,6/2,6 - - 1,2/5,2 - -
According to EN 13141-7 standard.
Smarty 2X V
Supply 60,3 51,8 56,0 61,1 55,2 50,4 46,1 31,9 Exhaust 47,4 36,4 50,2 47,4 38,2 26,7 19,8 22,9 Surrounding 47,7 46,4 52,0 45,6 38,4 28,9 24,3 22,9
Measured at ow/pressure [m3/h / Pa] 116/50
speed [min-1] 4060 3200
control input
protection class
phase/voltage
power/current [kW/A] 0,035/0,35 0,083/0,75
speed [min-1] 4060 3200
control input [VDC] 0-10 0-10
protection class IP54 IP54
LWA all, dB(A)
125 Hz 250 Hz 500 Hz 1 kHz 2 kHz 4 kHz 8 kHz
[50 Hz/
VAC]
[VDC] 0-10 0-10
[50 Hz/
VAC]
~1/230 ~1/230
IP54 IP54
~1/230 ~1/230
LWA, dB(A)
Smarty 3X V
Supply 62,8 54,3 64,9 61,1 56,5 51,3 42,8 35,3 Exhaust 47,7 42,0 54,6 45,0 36,0 28,8 19,6 22,4 Surrounding 49,0 47,2 54,8 46,1 39,5 34,2 24,9 22,6
Measured at ow/pressure [m3/h / Pa] 267/50
Exhaust air lter class G4 G4
Supply air lter class G4/(F7 - optional) G4/(F7 - optional)
LWA all, dB(A)
width L [mm] 270 475 height H [mm] 187 180 depth W [mm] 25 25 model MPL MPL
width L [mm] 270 475 height H [mm] 121 134 depth W [mm] 25 25 model MPL MPL
125 Hz 250 Hz 500 Hz 1 kHz 2 kHz 4 kHz 8 kHz
Smarty 2X V Smarty 3X V
LWA, dB(A)
NOTE. Subject to technical modication
12
W
www.salda.lt
Operational limits
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
40%
40%
40%
50%
40%
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
40%
50%
40%
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
40%
40%
40%
40%
40%
40%
50%
40%
40%
50%
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
40%
40%
50%
40%
40%
50%
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
50
14
150
42
200
56
250
69
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
40%
40%
40%
40%
100%
100%
40%
40%
50%
40%
40%
50%
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
40%
40%
100%
50%
40%
40%
50%
-7°C
2°C
7°C
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
50
14
150
42
200
56
250
69
50
14
150
42
200
56
250
69
v [m /h]
3
v [m /h]
3
v [l/s]
v [l/s]
Δ P [Pa]
stat
Δ P [Pa]
stat
50
45
40
35
30
25
20
15
10
5
0
50
14
150
42
200
56
250
69
P [W]
Δ P [Pa]
stat
v [l/s]
v [m /h]
3
40%
40%
40%
40%
100%
100%
40%
40%
50%
40%
40%
50%
-7°C
2°C
7°C
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
100
90
80
70
60
50
40
30
20
10
0
800
700
600
500
400
300
200
100
0 100 200 300 400 500
28 56 83 111
100%
100%
80%
80%
70%
70%
60%
60%
50%
v [m /h]
3
v [l/s]
Δ P [Pa]
stat
P [W]
900
40%
40%
100%
50%
40%
40%
50%
Power consumption
Smarty 2X V Smarty 3X V
Supply air Supply air
Temperature e󰀩ciency (balanced mass ow):
Extract air = 20 °C/60 % RH
Outdoor air = -7 °C / 2 °C / 7 °C
Exhaust air Exhaust air
Specic fan power (SFP) Specic fan power (SFP)
Temperature e󰀩ciency Temperature e󰀩ciency
www.salda.lt
Smarty 2X/3X V
13
Smarty 2X/3X V
732 mm
697 mm
35 mm
ø 125 mm
83 mm
79 mm
155 mm
82 mm
195 mm
386 mm
430 mm
125 mm /100 mm*
158 mm
595 mm
G3/8
242 mm
G3/8
156 mm
316 mm
82 mm
* Possibility to insert coupling of corresponding diameter
14
www.salda.lt
80 mm
810 mm
900,5 mm
Smarty 2X/3X V
Ø 160 mm
Ø 150 mm
110 mm
170 mm
252 mm
116 mm
110 mm
406 mm
599 mm
386 mm
Ø 150 mm/160 mm*
224 mm
G3/8
265 mm
113 mm
284 mm
G3/8
538 mm
* Possibility to insert coupling of corresponding diameter
www.salda.lt
15
Smarty 2X/3X V
40
mm
c
b
90
90
d
a
10
mm
10
mm
a
10
mm
b
c
14 mm
b
a
10
mm
10
mm
a
10
mm
b
b
a
10
mm
10
mm
• Installation should only be performed by qualied and trained sta󰀨.
• When connecting air ducts, consider the notices indicated on the casing of the unit.
• Before connecting to the air duct system, the connection openings of ventilation unit should be closed.
• When connecting the ducts , you should pay attention to the air ow direction indicated on the device housing.
• Do not connect the bends close to connection anges of the unit. The minimum distance of the straight air duct between the unit and the rst branch of the air duct in the supply air duct must be 1xD, in air exhaust duct 3xD, where D is diameter of the air duct.
• It is recommended to use the accessories-holders. This will reduce vibration transmitted by the unit to the air duct system and environment.
• Enough space must be left for opening of the maintenance door and lter covers.
• If the installed ventilation unit is adherent to the wall, it may transmit noise vibrations to the premises. Though the level of noise caused by the fans is admissible, it is recommended to mount the unit at the distance of 400 mm from the nearest wall. If it is not possible, the mounting of the unit is recom­mended on the wall of the room where the level of noise is not important.
• Ducts are connected to the unit in such way that they could be easily disassembled and the heater could be removed from the unit when performing service or repair works.
Smarty 2X V Smarty 3X V
Unit mounting on wall:
a) To reduce the vibration stick the insulating tape on the unit‘s casing side which touches the wall before mounting the unit on the wall. b) The unit has to be mounted on the mounting brackets. c) AHU mounting drawing.
Unit mounting on wall:
a) To reduce the vibration stick the insulating tape on the unit‘s casing side which touches the wall before mounting the unit on the wall. b) The unit has to be mounted on the mounting brackets. c) AHU mounting drawing. d) After the unit is mounted two wall bracket tabs has to be folded to 90o angle by pliers to avoid the accident fall of the unit.
Legs are optional and not included in standard package.
16
www.salda.lt
400 mm
Smarty 2X/3X V
L
2xL
• Supply voltage to the unit must be connected by a qualied specialist following the manufacturer’s instructions and e󰀨ective safety instructions.
• The unit’s power network voltage must correspond to electrotechnical parameters of the unit indicated in the technical decal.
• The unit’s voltage, power and other technical parameters are provided in the unit’s technical decal (on the unit casing). The unit must be connected to the voltage plug socket of the grounded power network in compliance with the e󰀨ective requirements.
• The unit must be earthed according to the rules on installing electrical equipment.
• It is prohibited to use extension wires (cables) and power network plug socket distribution devices.
• Prior to carrying out any ventilation unit installation and connection activities (until its hand-over to the customer), the unit must be disconnected from the power network.
• After installation of the ventilation unit, the power network plug socket must be accessible at any time and disconnection from the power network is performed through the two-pole circuit breaker (by disconnecting phase pole and neutral).
• The unit must be thoroughly checked against damages (execution, control, measurement nodes) during transportation before it is connected to the power network.
• The power cable can be replaced only by a qualied specialist upon the evaluation of the rated power and current.
The manufacturer does not assume any liability for personal injuries and property damage due to non­conformance with the provided instructions.
www.salda.lt
17
Smarty 2X/3X V
II
IV
I
VI
III
V
VII
VIII
It’s required to connect condensate drainage system after hanging or placement of air handling unit. Insert condensate draining into AHU. Condensate draining must
1
2
3
Before every heating season the condensate tube shall be lled with water as indicated during the rst start-up! Before every heating season the condensate tube shall be lled with water as indicated during the rst start-up!
be lubricated with sealant (I-VII). Then place plastic washer on the bottom and tight­en with counter nut (VII). Pipe (3) (metal pipe should be connected with G3/8 elbow, plastic pipe – with G3/8 elbow or rubber hose – with strap if the unit is placed on the legs, in other cases condensate hose can be connected in any direction) should be connected by following order: AHU (1), pipe (2), and drainage system. Pipes (3) should be bended not less than 3° degrees (1 meter of pipe must be bended 60 mm downwards)! Before turning on AHU (1) the draining system should be lled up with at least 0.5 l of water (pipe loop (3) must be always lled with water), also check if water reaches sewerage system! In other case premise can be ooded during AHU operation! Draining system must be installed in the premise where the temperature is not lower than 1°C. If temperature falls below 0°C the draining system should be isolated with thermal isolation. The pipe loop 2) not necessarily must be mounted below the AHU (1), but below the AHU (1) level. Note. If the collector is situated upstream, install a system with a condensate pump (o󰀨ered as an accessory).
3
D = min 150 mm
Air Handling Unit uses two types of boards, depending on the selected product version: miniMCB or miniMCB basic. Their functionality is di󰀨erent, thus check the board name by the product version.
Control board functions and logics are designed according to Standards DIN 1946-6:2009-05 and EN 12098-3. MCB control board can be controlled by: Ptouch remote control panel, Stouch remote control panel or MB - GATEWAY web application. Description of remote control panel functions is provided in the remote control panel technical documentation or on the website www.salda.lt.
The unit can be congured only with Ptouch remote control panel or MB-Gateway web application. The following control board functions can be fully controlled only with Ptouch remote control panel or MB-Gateway web application. In case of Stouch remote control panel use the description of remote control panel functions for MCB control board.
18
www.salda.lt
Loading...
+ 40 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use