Salamander Designs SNX20C-B User Manual

SYNERGY EXTENSION KIT - SX20 / SX30 / SX40

WARNING: If you are installing accessories such as doors or drawers to the base unit, read all instructions for the
accessory and install in conjunction with these instructions.

!

(300-450)

Connector Bolt

4x

(P-400-040) - Level

(400-060) - 3/16” Hex Key

1x

(400-080) - 5/32” Hex Key

1x

1x

Rear Panel Bag - PHK-240

1x

4x

4x

4x

(400-070) - 1/8” Hex Key

(300-560)

Flat Nut

(300-530)
ThumbNut

(300-510) - Stud

Rear Panel Bag - PHK-150 (Only SX40)

Parts

4 - Aluminum Posts Adjustable Shelf (SX20 -1) (SX30 - 2) (SX40 - 4)
1 - Top Shelf Heavy Duty Shelf Bracket (SX40 - 2)
1 - Rear Panels 1 - Spacer Tool

(PHK-370)
Shelf Peg “B”- Right

SX20 -2x
SX30 - 4x
SX40 - 6x

(PHK-380)
Shelf Peg “A” - Left

SX20 - 2x
SX30 - 4x
SX40 - 6x

4x

4x

(300-490)

Low Head Screw

(300-610)

Rubber Tab

4x

(300-560) - Flat Nut

4x

(300-260) - Felt Pads

Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com

Doc No. 500-360/v2 ©2002 Salamander Designs Ltd.

Limited Warranty

For five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original car ton and packing material. Any damage incurred in a
shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.

1

Remove Top Bolts

Remove the four connector bolts securing
the top shelf. Save for Step 6.

2

Attach Extension Post

A. Screw threaded studs into the ends

of the posts. Tighten with hex key.
Stick felt pads to underside of post,
this will prevent marring the surface
of the top shelf.

B. Screw the posts into the base unit.

Be sure to square the post with the
shelf. Do not over tighten.

B

B

A

A

B.

Position the peg through the Spacer
to desired position and tighten. You
may also consider using books or
CD's for shelf spacing.

A.

Insert all shelf pegs and heavy shelf
brackets (SX40 only) down each post.

3

Add Shelf Pegs

WARNING: If you are installing an optional door or drawer refer to
specific instructions before proceeding.

8"

SPACER

TOOL

!

A.Insert Hardware

Combine the 1” threaded studs
with the flat nuts. Slide hardware
into rear channel

B.

Allow studs to remain loose at
bottom of posts. Align the Spacer
Tool at the top of the post and
position top studs through the small
“Rear Panel” hole Secure the top 2
studs to the posts. Repeat this step
with the bottom studs, aligning the
Tool along the bottom of each post.

5

6

7

4

1
/
2

"

DRAWER 9.375

"

2X

2X

REAR

C. Placing Shelf

Place shelves from the bottom up.
Angle the shelf in between the front
post and set on top of shelf pegs
and heavy duty brackets.

1 2 3 4 5

S20 / SVDO

REAR PANEL

www.salamanderdesigns.com

EXTENDED

REAR PANEL

S30 / S40

REAR PANEL

4

Insert Rear Hardware

5

Final Assembly

STOP

Side Panels

Before enclosing the unit with the top shelf install side
panels (if applicable).

See Side Panel Instructions

A.Secure Rear Panel

Secure thumb nuts to finish panel
installation.

B.Install Top

Insert the four connector bolts and
tighten shelf down.

THE

SPACER

1

8"

"

6"

8

9

8"

6

1 8 9

SPACER

THE