Page 1
SYNERGY 339
!
Triple Assembly
BEFORE YOU BEGIN:
!
• Unpackallpartsandreadinstructionscarefullybeforebeginning.
•Shelfpegsanddoorhingesmustslideintothechannelsofthepostinthecorrectorder.
They cannot be removed individually without disassembly.
Includes:
(1) Triple 30 Unit
(2) S30 Si de Panels
(3) S20 Doors
(3) Adjustable Shelves
(1) Triple-Width Shelf
Connect Posts to Bottom Shelf
1
A. Square Post
Square the post to the bottom shelf.
O
90
B. Connect Post
Screw foot with metal washer through bottom
shelf and into the end of each extruded post.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.
Short Post
Washer
WARNING: Tighten by screwing the leveler foot NOT the post.
Leveler Foot
Limited Warranty
Five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in
a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Salamander Designs Ltd. • 800-535-5659 • www.SalamanderDesigns.com ©2006 Salamander Designs Ltd. Synergy System, Patented.
TM
Hex Nut
Doc No. 501-095/v4.12 339 -1/5
Page 2
Installing Hardware
2
D
C
C
3
Attach Rear Panels
A. Insert Hardware
Combine the 1” threaded studs with flat nuts.
Slide 2 sets of hardware down the two outside
C
posts and 4 sets down the two center post s.
Allow studs to remain loose at bottom of post.
B
A
A. Bottom Door Hinges
Slide the bottom door hinge
plate through the front post
channels (Doors can be either
left or right side opening).
C. Top Door Hinges
Slide the top door hinge plate
through the front post channels,
aligning with bottom door hinges.
A
A
B. Shelf Pegs
Insert one shelf peg down each post.
NOTE: There are two varieties of shelf pegs
(A and B). They are designed to cradle the
shelf in place. Refer to drawing.
A B
D. Heavy Duty Bracket
Install heavy duty brackets down outer
posts to support the triple-width shelf.
Place rubber shelf tabs through bracket.
2X
4X
4X
8"
TOOL
6"
SPACER
"
4
1/2
S30 / S40
REAR PANEL
S20 / SVDO
L
REAR PANE
ED
EXTEND
ANEL
REAR P
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
8"
TOOL
6"
SPACER
"
1/2
4
S30 / S40
ANEL
REAR P
/ SVDO
S20
R PANEL
REA
EXTENDED
REAR PANEL
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
2X
B. Position & Secure Studs
Align the Spacer Tool at the top of each post,
then position top studs through the small “Rear
Panel” hole. Repeat this step with the bottom
studs aligning the Tool along the bottom of post
to set spacing for cable passage. Use the hex key
to secure the top and bottom studs to the posts.
C. Place Rear Panels
Secure each panel in place with thumb nuts.
www.salamanderdesigns.com
1 2 3 4 5 6 7 8 9
REAR PANEL
EXTENDED
REAR PANEL
S20 / SVDO
REA
R PANEL
S30 / S40
4
1/2
"
SPACER
6"
TOOL
8"
TIP
To ease installation of rear
panels gently place the unit
face down on the floor to
improve aligning of panels.
8"
TOOL
6"
SPACER
"
1/2
4
S30 / S40
REAR PANEL
S20 / SVDO
REAR PANEL
EXTENDED
REAR PANEL
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
8"
TOOL
6"
SPACER
"
1/2
4
S30 / S40
REAR PANEL
O
S20 / SVD
REAR PANEL
EXTENDED
REAR PANEL
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
Doc No. 501-095/v4.12 339 - 2/5
Page 3
4
Placing Shelves
C
A
8"
TOOL
6"
SPACER
1/2
"
4
40
S30 / S
ANEL
REAR P
VDO
S20 / S
ANEL
REAR P
EXTENDED
L
REAR PANE
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
5
Install Spanner
A. Disassemble cross dowel using
the hex key as shown.
B. Install the cross dowels into both
ends of the spanner post as
shown. Gently tighten the set
screw in place with the hex key.
(Adjust set screw to move dowel
fastener in and out as needed.)
A. Adjustable Shelves
Place shelves from the bottom up. Angle
the shelf in between the front post and set
on top of shelf pegs. Use the Spacer Tool to
adjust spacing between shelves. Position the
peg through the Spacer and tighten.
C. Triple-Width Shelf
Place triple-width shelf on center
posts and secure with bolts.
NOTE:
Raise brackets to
bottom of shelf and
tighten in place.
B. Fine Tuning
Use the bubble level to precisely adjust
the adjustable shelves. Be sure to level
both sides as well as front to back. Use
the hex key to tighten each peg.
400-080
C. Slide the spanner post into the
front two riser posts.
SPACER
Adjust screw
to move in
and out.
Doc No. 501-095 /v4.12 339 -3/5
Page 4
6
Sides and Top Assembly
A. Insert Side Panels
Carefully slide side panels down outside posts. Be sure the posts are square
to the bottom shelf to prevent any damage to side panels.
B . Secure Top
Secure top with the connector bolts. Place the plastic plugs in the front
center holes.
Doc No. 501-095 /v4.12 339 -4/5
Page 5
7
Attach Doors
A. Attach Hinges to Door Frames
Insert the hinges into the corresponding holes
on the doors. Turn the screws 1/4 turn to the
right to lock hinges in place. NOTE: Do not over
tighten or the hinge will break.
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the hinge
base. Separated hinges snap back together.
LIFT UP
B. Adjust Clearance
Doors should be 1/8” above the bottom shelf before fully
tightening hinges to post. Use the wrench thickness as a guide
for the bottom gap. Secure hinges in place with hex key.
C. Rubber Stops
Attach the rubber stops to the
inside of the door frame where
it hits the shelf pegs.
SHELF
PEG
D. Door Pull
Screw the Door Pull into place.
Doc No. 501-095/v4.12 339 -5/5
CLOSE
INSTALLATION
A
B
SOFT
SLOW CLOSE
FAST CLOSE
Loading...