Page 1
TM
SYNERGY 329
Twin Assembly
Includes:
(1) Twin 30 Unit
(2) S30 Side Panels
(2) S20 Doors
(2) Adjustable Shelves
(1) Double-Width Shelf
Salamander Designs Ltd. • 800-535-5659 • www.SalamanderDesigns.com ©2006 Salamander Designs Ltd. Synergy System, Patented.
Limited Warranty
Five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in
a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Doc No. 501-100/v9.06 329 -1/4
BEFORE YOU BEGIN:
• Unpack all parts and read instructions carefully before beginning.
• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.
1
90
O
B.Connect Post
Screw foot with metal washer through bottom
shelf and into the end of each extruded post.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.
A.Square Post
Square the post to the bottom shelf.
Connect Posts to Bottom Shelf
!
Short Post
WARNING: Tighten by screwing the leveler foot NOT the post.
Leveler Foot
Hex Nut
Washer
Page 2
Doc No. 501-100/v9.06 329 - 2/4
C
2
Installing Hardware
D.Heavy Duty Bracket
Install heavy duty brackets down outer
posts to support the double-width shelf.
Place rubber shelf tabs through bracket.
A.Bottom Door Hinges
Slide the bottom door hinge
plate through the front post
channels (Doors can be either
left or right side opening).
B.Shelf Pegs
Insert one shelf peg down each post.
NOTE: There are two varieties of shelf pegs
(A and B). They are designed to cradle the
shelf in place. Refer to drawing.
C. Top Door Hinges
Slide the top door hinge plate
through the front post channels,
aligning with bottom door hinges.
D
B
A
A B
C
A
A.Insert Hardware
Combine the 1” threaded studs with flat nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the center post. Allow
studs to remain loose at bottom of post.
B.Position & Secure Studs
Align the Spacer Tool at the top of each post,
then position top studs through the small “Rear
Panel” hole. Repeat this step with the bottom
studs aligning the Tool along the bottom of post
to set spacing for cable passage. Use the hex key
to secure the top and bottom studs to the posts.
C.Place Rear Panels
Secure each panel in place with thumb nuts.
Attach Rear Panels
3
4X
2X
2X
TIP
To ease installation of rear
panels gently place the unit
face down on the floor to
improve aligning of panels.
www.salamanderdesigns.com
1 2 3 4 5 6 7 8 9
REAR P
ANE
L
E
XTENDED
REA
R
PANEL
S
20
/ S
VDO
REAR PANEL
S30 / S40
4
1/2
"
SPACER
6"
TOOL
8"
8"
TOOL
6"
SPACER
"
1/2
4
S30 / S40
REAR PANEL
VDO
/ S
S20
L
ANE
R P
REA
ED
END
EXT
L
ANE
R P
REA
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
8"
6"
"
1/2
4
40
S
S30 /
L
REAR PANE
S20 / SVDO
REAR PANEL
ED
END
EXT
L
ANE
R P
REA
1 2 3 4 5 6 7 8 9
TOOL
SPACER
www.salamanderdesigns.com
8"
TOOL
6"
SPACER
"
1/2
4
0
S30 / S4
REAR PANEL
/ SVDO
S20
REAR PANEL
ED
EXTEND
REAR PANEL
1 2 3 4 5 6 7 8 9
www.salamanderdesigns.com
Page 3
B. Fine Tuning
Use the bubble level to precisely adjust
the adjustable shelves. Be sure to level
both sides as well as front to back. Use
the hex key to tighten each peg.
A. Adjustable Shelves
Place shelves from the bottom up. Angle
the shelf in between the front post and set on
top of shelf pegs. Use the Spacer Tool to
adjust spacing between shelves. Position the
peg through the Spacer and tighten.
D. Double-Width Shelf
Place double-width shelf on brackets.
C. Rubber Pads
Place rubber pad on top of center post.
A
C
D
A. Insert Side Panels
Carefully slide side panels down
outside posts. Be sure the posts are
square to the bottom shelf to prevent
any damage to side panels.
Doc No. 501-100/v9.06 329 -3/4
4
Placing Shelves
B. Secure Top
Secure top with the 5 connector bolts.
Place the plastic plugs in the front center hole.
5
Sides and Top Assembly
Page 4
6
SOFT
DE
FI NING O RIG
INAL
™
DE FI NING O RI G INA
L
™
D
EFIN ING ORIGINA L
™
Logomark
Logotype
TaglineRule
A.
Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place. NOTE: Do not over tighten
or the hinge will break.
Attach Doors
Attach Hinges to Door Frames
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the hinge
base. Separated hinges snap back together.
LIFT UP
B.
Adjust Clearance
Doors should be 1/8” above the bottom shelf before fully
tightening hinges to post. Use the wrench thickness as a guide
for the bottom gap. Secure hinges in place with hex key.
C.
Rubber Stops
Attach the rubber stops to the
inside of the door frame where
it hits the shelf pegs.
SHELF
PEG
Door Pull
D.
Screw the Door Pull into place.
Doc No. 501-100/v9.06 329 -4/4
CLOSE
INSTALLATION
A
B
SLOW CLOSE
FAST CLOSE
Loading...