Page 1
SYNERGY 248
!
Quad Assembly
Includes:
(1) Quad 20 Baseunit
(4) Side Panels
(4) Rear Panels
(2) S20 Doors
(2) S10 Doors
(2) Adjustable Shelves
(1) Double Width Shelf
PHK - Parts:
BEFORE YOU BEGIN:
!
• Unpack all parts before beginning and refer to the drawing below.
• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.
(2) Hardware Bags
(2) Double Wide Shelf Brackets
Limited Warranty
For ve full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factor y prepaid, in the original carton and packing material. Any damage incurred in a
shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com ©2005 Salamander Designs Ltd. ® Synergy System, Patented.
Doc No. 500-255 v 7/11 1 of 4
Page 2
Connect Posts to Bottom Shelf
!
1
WARNING: Tighten by screwing the leveler foot NOT the post.
!
A.
Square Post
Square the post to the bottom shelf.
B. Connect Post
Screw foot with metal washer through bottom
shelf and onto the end of each extruded post.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.
90
Add Shelf Pegs & Door Hinges
2
A. Group Shelf Pegs
There are two varieties of shelf pegs (A and B).
O
They are designed to cradle the shelf in place.
Refer to drawing.
2
1
1
2
2
1 2
1
1
2
Note:
“BOTTOM SIDE FRONT”
Label position down. and
!
towards front - Both Panels
Washer
Hex Nut
Leveler Foot
B. Heavy Duty Bracket
The heavy duty brackets will be used
to support the double-width shelf.
C. Door Hinges & Shelf Pegs
1. Slide the bottom hinge plate through
the front post channels. (Doors can be either
left or right side opening.)
2. Insert one shelf peg into each post
location shown.
3.
Slide top hinge plate through front
post channels.
Use spacer tool as in step 5 to align
4.
brackets and pegs.
Doc No. 500-255 v 7/11 2 of 4
Page 3
3
Attach Doors
A. Attach Hinges to Door Frames
Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place.
or the hinge will break.
NOTE: Do not over tighten
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the
hinge base. Separated hinges snap back together.
PULL
B. Adjust Clearance
Doors should be 1/8” above the bottom shelf before fully
tightening hinges to post. Use the wrench thickness as a guide
for the bottom gap. Secure hinges in place with hex key .
C. Rubber Stops
Attach the rubber stops to the inside of the door
frame where it hits the shelf pegs.
SHELF
PEG
D. Door Pull
Screw the Door Pull into place.
Doc No. 500-255 v 7/11 3 of 4
Page 4
4
SOFT
DE FI NING ORI GINAL
™
DE FI NING OR IG INAL
™
DEFINING ORIGINAL
™
Logomark
Logotype
TaglineRule
Attach Rear Panels
Final Assembly
5
A.
Insert Hardware
Combine the 1” threaded studs with the at nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the three center posts.
Allow studs to remain loose at bottom of post.
2X
4X
REAR
4X
B. Position & Secure Studs
Align the Spacer Tool at the top of each post,
then position top studs through the small “Rear
Panel” hole. Repeat this step with the bottom studs
aligning the Tool along the bottom of post to set
spacing for cable passage. Use the hex key to
secure the top and bottom studs to the posts.
4X
2X
A. Placing & Adjusting Shelves
Place shelves from the bottom up. Angle the
shelf in between the front post and set on top
of shelf pegs. Use the Spacer Tool to adjust
spacing between shelves. Position the peg
through the Spacer and tighten.
B. Fine Tuning
Use the bubble level to precisely adjust
the shelves. Be sure to level both sides
as well as front to back. Use the hex
key to tighten each peg.
C. Insert Side Panels
Carefully slide side panels down center
channel of outside and center posts as
shown. Be sure the posts are square to
the bottom shelf to prevent any damage
to side panels.
CLOSE
INSTALLATION
A
C. Place Rear Panels
Secure each panel in place with thumb nuts.
D. Secure Top
Secure top with the 9 connector
bolts to complete installation.
B
Doc No. 500-255 v 7/11 4 of 4
Loading...