Page 1
SYNERGY 133
!
Triple Assembly
Includes:
BEFORE YOU BEGIN:
!
• Unpack all parts before beginning and refer to the drawing below.
• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.
(1) Triple 10 Unit
(2) S10 Side Panels
(3) S10 Doors
Joint Connector Bolt 300-540 (8)
Washer 300-470 (8)
Foot & Nut P-300-350 (8)
Top Shelf (1)
Bottom Shelf (1)
Rear Panel (3)
Aluminum Post (8)
Sides (2)
Door (2)
Door
Hinge (6)
Limited Warranty
For five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or
destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing
material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com ©2005 Salamander Designs Ltd. ® Synergy System, Patented.
Doc No. 501-065 / v6.12 133 - 1 of 4
Page 2
1
!
Connect Posts to Bottom Shelf
WARNING: Tighten by screwing the leveler foot NOT the post.
!
A. Square Post
Square the post to the bottom
shelf.
O
90
2
Carefully slide the three rear panels down center channel of rear posts. Be sure
the posts are square to the bottom shelf to prevent any damage to rear panels.
Insert Rear Panels
REAR
B. Connect Post
Screw foot with metal washer
through bottom shelf and onto
the end of each extruded post.
Hand tighten fully and use
wrench to tighten nut onto
underside of shelf.
Washer
Hex Nut
Leveler Foot
Doc No. 501-065 / v6.12 133 - 2 of 4
Page 3
Attach Doors
3
A. Attach Hinges to Door Frames
Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place. NOTE: Do not over tighten
or the hinge will break.
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the
hinge base. Separated hinges snap back together.
PULL
B. Adjust Clearance
Doors should be 1/8” above the bottom shelf before
fully tightening hinges to post. Use the wrench thickness
as a guide for the bottom gap. Secure hinges in place
with hex key.
C. Rubber Stops
Attach the rubber stops to the inside of the door
frame where it hits the shelf pegs.
SHELF
PEG
D. Door Pull
Screw the Door Pull into place.
Doc No. 501-065 / v6.12 133 - 3 of 4
Page 4
4
DE F INING ORIG INAL
™
DE F INING ORIG INAL
™
DEFINING ORIGINAL
™
Logomark
Logotype
TaglineRule
Insert Side Panels
Carefully slide side panels down center channel
of outside posts. Be sure the posts are square to the
bottom shelf to prevent any damage to side panels.
5
Secure Top
Secure top with the 8 connector bolts to complete installation.
SOFT
CLOSE
INSTALLATION
A
B
SLOW CLOSE
Doc No. 501-065 / v6.12 133 - 4 of 4
FAST CLOSE
Loading...